Search Documents

By Park. D. W., Y. M. Jiang, L. A. Morley, W. Keeton

Underground room-and-pillar mining operations in the Warrior Coal Field in Alabama frequently suffer instability due to soft floors and thinly-laminated immediate roofs. This investigation concerns a mine that was experiencing ground-control problems with weak floor conditions. Several roof falls occurred locally, and as much as 0.6 m (2 ft) of floor heaves have been experienced. The paper presents the results of comprehensive analyses conducted on floor heave, roof sagging, pillar- penetration and floor bearing capacity using instrumentation and numerical modeling.

Jan 1, 1993

By Shiwei Wang, Ziwen Li, Chenhu Zhang, Peng Chen, Chengyong Wang

Accurate prediction of the partition coefficients in coal gravity separation is key to improving the preparation efficiency of coal and promoting its clean utilization. In China, the approximate formula method (AFM) has been applied to the calculation of coal gravity separation partition coefficients for decades, but its accuracy is limited. To improve the accuracy of the predicted partition coefficients, and thus the product yield of coal preparation plants, the present study proposes a modified hyperbolic tangent model to derive direct calculation formulas for the heavy medium and water medium separation partition coefficients. Four groups of coal samples were used to verify the accuracy of the direct formulas, and their predictions were compared with those of the AFM. The results showed that the partition coefficients and partition curves predicted by the direct formulas were closer to the actual values than those predicted by the AFM. Further, when the cleaned coal ash content was basically the same, the cleaned coal yield predicted by the direct formula was lower than that predicted by the AFM, and was also closer to the actual value. These results demonstrate that the direct formula produces more accurate results compared to the conventional AFM. As this formula has a reasonable theoretical basis, is simple to apply, and produces accurate results, it is expected to help improve the design and management level of coal preparation plants.

Oct 15, 2022

By Frank X. Bellini, Marc Saidman, Allen J. Hulshizer, Anthony J. Stewart

The cooling water system for the Seabrook Nuclear Station involves 10.25 Km (33,623 ft.) of 6.7 m (22 ft.) OD hard rock tunnels, over one third of which is under and terminating over 1.6 Km (a mile) out in the Atlantic Ocean. The major excavation is accomplished by two TBM's concurrently driving the intake and discharge tunnels which by mid-January, 1981, completed 92% of the excavation. This paper presents the case history of the excavation work and describes a computer program developed to evaluate major activities of TBM excavation on a shift-by-shift basis. Details and summaries of the production efforts are computer plotted in different forms to facilitate the evaluation of production performance, trouble spots and trends.

Jan 1, 1981

By Yongsik Jeong, Kwangmin Kim

Most tailings storage facility (TSF) failures occur in active, upstream-type TSFs, often due to extreme and unexpected weather conditions—specifically, heavy rainfall and strong winds. This case study of a TSF in southern Arizona examines the use of the optimum safe beach distance (Doptimal, the optimum distance between the crest and decant pond) as a tool for monitoring geotechnical stability and reducing catastrophic failures. A digital model of the TSF was used to determine the critical beach distance (Dcritical) under normal weather conditions, and Doptimal was then determined by adding incremental distances to account for the effects of heavy rainfall (Drainfall) and strong winds (Dwind). To overcome accessibility issues, a drone was used to map the TSF geometry and create a digital model. This model served as the basis for conducting a coupled stress-seepage, finite-element (FEM) analysis with a safety factor of 2.0 to assess geotechnical stability (Dcritical). The safe beach distance increments were determined using the PMP (probable maximum precipitation) and possible maximum wind speed. Based on this analysis, the optimal safe beach distance at the study site was identified as 202.2 m. Since the current beach distance (371 m) exceeds this value, the TSF was considered to be stable and satisfied the design safety factor of 2.0. However, this distance should be reassessed periodically to account for changes in the TSF geometry and other conditions. Furthermore, it applies only TSFs that are well-managed and feature a smooth, non-undulating beach surface with a consistent slope.

By S. A. Moffatt, S. K. Kawatra, T. C. Eisele

This paper describes the decomposition of bulk samples to fine particles using alkali metal vapors. Basalt, pyrite, alumina, pyrex and quartz glass samples were exposed to sodium vapors at elevated temperatures for different time periods up to 30 hours. Examination of the particles showed that fragmentation occurred preferentially along grain boundaries. Emphasis of this paper is on the theory of the degradation mechanism and the size distribution of the particles produced.

Jan 1, 1992

By A. Vien

A major thrust in Industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements In control performance can be achieved by getting back to the basics.

Jan 1, 1998

By Zhongwei Wang, Dong Wang, Feng Ju

The coal seam in the southern coal field of the Ordos Basin serves as the main aquifer, while the region is known for its high-intensity coal mining activities. The coupling effect of mine water and the strong disturbance caused by high-intensity mining have brought serious challenges to the stability of coal pillars. To address this, a formula for determining the reasonable width of coal pillars under the aforementioned coupling effect and establish a criterion for coal pillar instability in this paper. A case study was on the 11,215 working face at the Xiaojihan coal mine in the area to investigate coal pillar stability. Results indicate that the strength and stability of the coal pillar are affected by the water content, with a small water content increasing its strength and large water content weakening it. In high-intensity exploration of watery coal seams, the best stability of the coal pillar is achieved at optimal water content and mining rates. For the Xiaojihan coal mine, the optimum water content and mining rate are 3.31% and 20 m/d, respectively, ensuring the efficient mining of watery coal seams. Furthermore, this study's findings can provide valuable references for the mining design of coal mines with similar geological conditions in the region.

Feb 13, 2024

By Tedd B. Bodimer

Why complicate an already complex machine such as a continuous miner by adding roof drills? Immediate permanent roof support is an immediate thought of the mining engineer just as elimination of frequent time-consuming places changes is a thought of the methods engineer. The realization of those two objectives has the potential for improved safety with increased production is the thought of the general manager. Miner-Bolters Used a Generation Ago These are not new thoughts as the 1CM continous miner equipped with two integral roof drills was introduced twenty-five years ago. Approximately two hundred of these machines were sold in the next five years for use in medium and high seam operations. The 1CM miner chassis that remained stationary in the center of an entry or room while the ripper bar was swung and sumped hydraulically provided an ideal platform for mounting two roof drills that could be operated during the continuous miner's production cycle. Two roof bolts could normally be installed in less time than required for the mining cycle. A typical roof drill unit is shown in Figure I.

Jan 1, 1981

By Tsuneyoshi Funazaki, Takayoshi Nakamura, Keizo Miki, Takashi Imaishi

The underground portion (about 10 km) of Tokyo Wan Aqua-Line consists of eight shield tunnels connected with Kawasaki Man-Made Island in between, at four underground locations. The connection work had to fulfill strict precision and safety requirements in the ground about 60 m below soft seabed, but was completed successfully in May 1997. This report describes the connection work in detail, featuring the method of investigating shield machines’ relative positions, ground freezing method and connection mechanism and procedures. It also mentions the present state of Tokyo Wan Aqua-Line that was put in service on December 18, 1997.

Jan 1, 1999

By Yongsik Jeong, Kwangmin Kim

Most tailings storage facility (TSF) failures occur in active, upstream-type TSFs, often due to extreme and unexpected weather conditions—specifically, heavy rainfall and strong winds. This case study of a TSF in southern Arizona examines the use of the optimum safe beach distance (Doptimal, the optimum distance between the crest and decant pond) as a tool for monitoring geotechnical stability and reducing catastrophic failures. A digital model of the TSF was used to determine the critical beach distance (Dcritical) under normal weather conditions, and Doptimal was then determined by adding incremental distances to account for the effects of heavy rainfall (Drainfall) and strong winds (Dwind). To overcome accessibility issues, a drone was used to map the TSF geometry and create a digital model. This model served as the basis for conducting a coupled stress-seepage, finite-element (FEM) analysis with a safety factor of 2.0 to assess geotechnical stability (Dcritical). The safe beach distance increments were determined using the PMP (probable maximum precipitation) and possible maximum wind speed. Based on this analysis, the optimal safe beach distance at the study site was identified as 202.2 m. Since the current beach distance (371 m) exceeds this value, the TSF was considered to be stable and satisfied the design safety factor of 2.0. However, this distance should be reassessed periodically to account for changes in the TSF geometry and other conditions. Furthermore, it applies only TSFs that are well-managed and feature a smooth, non-undulating beach surface with a consistent slope.

By Charles E. Glass

As partial implementation of the Surface Mining Control and Reclamation Act of 1977, the Office of Surface Mining (OSM), Department of Interior, has requested each state to inventory hazardous abandoned mining areas within their boundaries. Primary interest is in such areas .as unstable waste-banks, subsidence and slumping, contamination of water supplies, and preservation of overall aesthetic qualities through reclamation. In addition to the concern expressed for abandoned mining areas, the legislation requires a complete inspection of operating mines quarterly and a partial inspection monthly. In Arizona copper has been mined for over 100 years and coal and uranium mining promises to expand in future years. The OSM requirement for a waste inventory and frequent monitoring of Arizona's large, widely spaced mines places a severe demand on limited personnel and operating budgets. Remote sensing by satellite provides an attractive and effective approach to aid the inventory and monitoring requirements of the OSM legislation.

Jan 1, 1979

By Joseph W. Leonard

Much progress has been made in the application of geostatistics to hard rock ore deposits.1,2,3 4,8 Progress in the application of geostatistics to coal deposits has developed over a period of time out of hard rock technology.5,7 Exploratory drilling in many hard rock deposits is frequently significantly more productive than exploratory drilling in coal deposits. For example, hundreds of feet of drilling and/or many drill setups are frequently necessary to obtain a few samples from a typical 4 to 6 foot thick coal seam. With hard rock deposits, which are frequently thick or volumetric, less drilling dead work is involved in sampling the deposit. To produce a variogram, which is the basic element needed for geostatistical analysis, a few well positioned holes drilled into a hard rock deposit where the core(s) can be divided into many sections can produce a detailed variogram. To produce a similar type variogram in coal, it is necessary to drill many dozens of holes with much of the core length consisting of overburden data which is frequently of only secondary importance. To apply geostatistics to coal, not only are many separate sample sites needed, but frequently a problem exists in that the interval distance between samples cannot be controlled with the ease that hard rock drilling intervals can be controlled where it is only necessary to cut core segments according to some preassigned interval of distance. Because the uses of existing coal deposit samples are frequently handicapped by irregular sample distances and lack of sampling density along certain directions needed for the development of variograms, the application of geostatistics to coal deposits frequently does not proceed with the same efficiency and rapidity as when these techniques are applied to ore deposits. Grid-fitting was developed by the writers, as a logical and evolutionary improvement over the long and successful application of geostatistics to coal seams.6,9 Grid-fitting combines the trending of variance as well as other aspects of probability theory to optimize informational yields from the commonly less productive data derived from coal exploratory programs. Grid-fitting is basically a technique where a hypothesis involving numerous grid patterns, where each pattern is of a given geometry, size and direction is repeatedly matched against actual sample data to determine which match results in the closest fit of the hypothesis to the data. To determine the closest fit, a special index known as a selectivity index was developed. The selectivity index is basically the product of the mean and variance of the variances contained within each of the grids. hence, if SI is the selectivity index then [SI = Xs E (S i - Xs) /N] where [X]s is the mean of individual grid variances Si2 for any pattern of given geometry, direction and size.

Jan 1, 1984

By Pan Gao, Songyang Yin, Zhibiao Guo, Jinglin You, Yuhui Li

Under the geological conditions of the interaction of upper goafs and lower working face in deep mining, coal seam mining causes a large stress concentration, which may lead to large deformation of the surrounding rock and rock burst risk. The research reported herein is aimed to utilize the FLAC3D software to establish a three-dimensional numerical model and analyze the law of the surrounding rock stress evolution during coal mining under complex geological conditions. The simulation results reveal that the peak abutment stress reaches its maximum value at 20–30 m in front of the working face, about 1.8–4.3 times the original rock stress, and the peak stress is larger in the stable mining stage. Along the dip of the working face, the peak stress occurs about 8–10 m away from the roadway side. The upper barrier coal pillar and the interval coal pillar in order exhibit stress concentration areas of 142 m and 88 m. According to the law of the deflection stress distribution of the surrounding rock in the presence of various widths of the coal pillar, a 10-m coal pillar between the roadway and the adjacent goaf could enhance the stability of the roadway. For the stress concentration area, drilling holes with a depth of 20–25 m are utilized to reduce the pressure, and anti-impact supports are installed in the middle of the roadway. Due to the varying stresses of the rocks around the roadway, partition prevention and control countermeasures are capable of efficiently preventing the instability of the surrounding rock.

Mar 22, 2023

By Y. Luo

Based on the concept of slope stability analysis, a formula for determining an important parameter required in the mathematical model for the prediction of mining subsidence in hilly terrain has been proposed. The slope geometry and soil physical and mechanical properties of the surface natural slope can all be considered in the formula. Incorporation of this new formula into an existing mathematical model provides an integrated approach in studying ground movement in hilly regions.

Jan 1, 1998

By J. N. Hartley

Uranium mill tailings, waste products of uranium extraction, contain hazardous constituents that if released into the atmosphere and groundwater could threaten our health and environment. To provide for safe disposal and control of these tailings, Congress enacted the Uranium Mill Tailings Radiation Control Act of 1978 (Public Law 95-604). Subsequently, the Environmental Protection Agency (EPA) established standards for tailings disposal that limit radon emission into the air to 20 pCi m-2s-1 on an annual average basis (EPA 1983). The design life of the impoundment is to be 1000 years where practicable, but 200 years at least. To facilitate the design of containment systems that will meet the EPA standards, the Nuclear Regulatory Commission (NRC) and the Department of Energy (DOE) are sponsoring research at the Pacific Northwest Laboratory (PNL)* to develop the necessary technology. Earthen and asphalt materials have been evaluated for use as radon barriers (Hartley 1983) and as liners to minimize leaching (Buelt 1983). Herbicide and rock barriers against biological intrusion have been evaluated (Cline 1982). Surface stabilization techniques have been investigated to maintain the long-term effectiveness of a containment system that must be protected from wind and water erosion, chemical and physical degradation, and biological disturbance.

Jan 1, 1984

By Thomas Bubanovich

Engineers at the Freeman United Coal Min¬ing Company, located in West Frankfort, Illinois, have been using a computerized production planning and maintenance reporting system, which have been designed exclusively for underground coal mining. This paper will explain a dynamic graphical simulation and computerized time study system that has been used to design and evaluate underground production systems for optimizing productivity. Also with the aid of customized software, detailed records on changeable components of underground equipment, including the vendor's name, date installed, operating and maintenance hours, etc., have helped Management to select the best available components for their equipment. The MPASS System, Mine Performance Analysis Simulation System, developed through a cooperative agreement with Freeman United, Ketron Inc., and the U. S. Department of Energy utilizes new methods to analyze and design production systems in underground coal mines. The MPASS System is a menu-driven user oriented system of interactive computer programs, which form five major subsystems. The subsystems: 1. Simulation 2. Time Study 3. Mine Background Reports 4. File Maintenance Subsystem 5. Statistical Analysis Subsystem

Jan 1, 1987

By I. Abdullayev, M. Soberano Capistran, J. Garcia

The application of post-tensioning in segmental structures was introduced in the early 1900s and has been successfully applied in different types of structures including immersed tunnels, bridges, buildings, metro stations, and stadiums. There are, however, only five known circular concrete tunnel projects where the post-tensioning approach has been adopted. This paper discusses the application of post-tensioning to mitigate the high internal operating pressures in an effluent outfall tunnel project 7 miles, 11.3 km long, currently under construction for the Los Angeles County Sanitation Districts, LACSD. This project will be the first use of post- tensioned segmental concrete tunnel linings in North America.

Jun 23, 2024

By g. Caproni

The main constituent of the feed to the "Sulphide Section" (31 t/h), in the F. Sartori Plant (6000 tid) of the Miniere di Mon)eponi(Sardinia), is the ore of the Campo Pisano -Funtanaperda Mine (1 ? Difficulties have always been experienced in the treatment of this ore, owing to the extramely fine Pyrite-Sphalerite intergrowth and to the high Pyrite and soluble salts contents. The first mentioned difficulty was overcome with a rather complex flowsheet (see fig.1A and lB)(2); the others with a reagent combination that required a pH of 11 in a pulp loaded with soluble salts. This meant high consumption of alkalizer, and also of the other reagents; furthermore the alkalizer had to be mainly NaOH with only minor amounts of lime, because the latter tended to depress not only the pyrite but also the middlings, which were supposed to float. With dialchylditiophosphate alone as a collector, a lower pH could have been used, but a certain amount of amylxanthate was indispensable to promote flotation of the middlings. On the other hand, a bulk-flotation of sphalerite and pyrite at low pH could not be very advantageous on account of the high pyrite content in the feed(3).

Jan 1, 1971

By L. P. James

The Bulagidun copper-gold system occurs in Tertiary andesitic volcanic rocks. It is located (figure 1, from Curless, 1991) ca. two days walk from the coast in an isolated area on the northerly slope of the main range of mountains, in steep terrain dissected by erosion. Detailed and district-scale exploration from 1988 to 1991 by BHP Minerals defined a small, sub-economic resource of gold and copper. One preliminary estimate of the resource in bedrock suggests 14.4 million tons at 0.68 grams / Tonne Au and 0.61% Cu, in multiple small bodies.

Jan 1, 1993

By V. S. Znamensky, R. V. Stewart

This chrysotile asbestos ore body is located near the northern tip of the Province of Quebec, Canada. It is some 1818 km (1130 miles) north of Montreal, 480 km (300 miles) north of the tree line, and is situated within the zone of continuous permafrost. The open pit ore zone is approximately 0.4 km (1% mile) in length, some 61 m (2OO ft) in width and plunges at 25o to 30 o below surface to a vertical depth of at least 610 m (2000 ft). The ore body was originally evaluated by programs of surface mapping, diamond drilling, and bulk sampling. The fiber is semicrude, possesses excellent strength, and good fiber length distribution. GEOLOGICAL SETTING, LOCATION, AND DISCOVERY The chrysotile asbestos mineralization at the Asbestos Hill mine occurs in serpentinized ultrabasic rocks of Precambrian age. These intrusive rocks are found in older volcanic sedimentary rocks known as the Cape Smith-Wakeham Bay belt and are shown in Fig. 1. The rocks comprising this belt overlie older basement rocks composed of granite and granite gneiss. This belt has a width of 32 to 64 km (20 to 40 miles), and trends in a general east- west direction, a distance of about 370 km (230 miles) from Wakeham Bay on the east coast of the Ungava Peninsula to Cape Smith, located on the east side of Hudson Bay. Two sequences of rock have been recognized in this belt. The lower (oldest) rocks are known as the Povungnituk group, and consist principally of massive lavas and sediments. The upper (younger) rocks are known as the Chukotat group, and are composed of pillowed lavas with interbedded sedimentary rocks. Sills of ultrabasic rocks exist in both younger and older rocks, but are more often found in the Povungnituk group. Concentrations of chrysotile asbestos, as well as nickel and copper minerals are found at or near the base of ultrabasic sills, and are most common where a change in dip occurs. The mine is situated about 1818 km (1130 miles) north of Montreal, approximately 1126 km (700 miles) north of the start of continuous permafrost, and about 482 km (300 miles) north of the tree line. The depth of permafrost at the mine site has been calculated to be approximately 549 m (1800 ft). This rich deposit of asbestos was discovered in 1957 during extensive exploration for nickel in the Ungava nickel belt. During that year, traverses conducted by Murray Watts spotted interesting looking ultrabasic rocks, and followup ground examination disclosed rich surface showings of asbestos mineralization near the present open pit. In 1958, a two-man prospecting party returned to the discovery site and a mineral exploration license was granted to Fig. 1. Location map Keewa Quebec Mines Ltd., a wholly owned

Jan 1, 1986