Search Documents

By C. Douglas Lee

This case study describes the work done at the University of Arizona on the development of a computer mine model for an irregularly shaped and spotty ore deposit. The purpose of the work was to develop techniques for modeling any highly irregular deposit, for which the regular 3D fixed block model is not well suited. The deposit contained complex geology consisting of sedimentary beds that had been faulted, thrusted, and intruded by igneous rocks (see Fig. 1). The physical dimensions of the modeled ore body were 1067 m (3500 ft) along the N-S direction and 914 m (3000 ft) along the E-W direction. Topographic relief in the modeled area was approximately 274 m (900 ft). The highest grade of ore was found near the surface with mineralization extending down to approximately 152 m (500 ft) below. Using a fixed bench height of 12 m (40 ft), the model required 25 levels with the highest elevation being at 1286 m (4220 ft). Fig. 2 shows a cross section of the developed computer model of the ore deposit. The particular modeling approach selected for this deposit was the 3D irregular block model.* This meant that only the dimension of bench height was fixed at 12 m (40 ft). Irregular size blocks in the form of polygons were adopted in the model to describe the ore zones and geologic contacts. The following sections of this chapter describe some of the techniques used in modeling.

Jan 1, 1979

By J. Wagner, P. Eger, G. Melchert

In 1991, LTV Steel Mining decided to close an open-pit taconite mine in northeastern Minnesota using a passive-treatment approach consisting of limiting infiltration into the stockpiles and wetland treatment to remove metals. More than 50 Aft (55 million st) of sulfide-containing waste had been stockpiled adjacent to the mine during its 30 years of operation. Drainage from the stockpiles contained elevated levels of copper, nickel, cobalt and zinc. Nickel is the major trace metal in the drainages. Before the closure, the annual median concentrations ranged from 1.5 to 50 mg/L. Copper, cobalt and zinc are also present but they are generally less than 5% of the nickel values. Median pH levels range from 5 to 7.5, but most of the stockpile drainages have pH levels greater than 6.5. Based on the chemical composition of each stockpile, a cover material was selected. The higher the potential that a stockpile had to produce acid drainage, the lower the permeability of the capping material required Covers ranged from overburden soil removed at the mine to a flexible plastic liner. Predictions of the reduction in infiltration ranged from 40% for the native soil to more than 90% for the plastic liner. Five constructed wetlands have been installed since 1992. They have removed 60% to 90% of the nickel in the drainages. Total capital costs for all the infiltration reduction and wetlands exceeded $6.5 million, but maintenance costs are less than 1 % of those for an active treatment plant. Because mine-drainage problems can continue for more than 100 years, the lower annual operating costs should pay for the construction of the wetland-treatment systems within seven years.

Jan 1, 2000

By K. A. Grace, D. E. Ranta

The application of geology does not cease with the discovery and delineation of a mineral resource, but continues in the calculation of the economic parameters that determine reserves. Reserve determination, reduced to essentials, is the determination of the cost of production of a mineral commodity from a resource. This cost comprises mining, processing, waste disposal, reclamation and marketing costs. Geological input is vital in the calculation of the individual cost parameters from mining to reclamation, and even has same impact on marketing. Geology thus has a critical role in the determination of reserves.

Jan 1, 1992

By Richard C. Corson

The new 9300 TPD sinter plant being built for China Steel Corporation is incorporating the latest computer technology for plant control systems. The control system will use a central computer and distributed micro-processors to control instrument loops and switching logic in the blending yard and sintering plant. All plant functions, including combustion and fan controls, will be controlled by remote microprocessors located throughout the plant, and connected by a communications link to the centrally located computer and control room. The design, programming, construction and operation of a microprocessor based control system presents new challenges to the control engineer. With microprocessors in the control system, more power exists in the individual control loop and many supervisory functions may be added at the loop level. The specification of the microprocessor system and the resolution of hardware design and control system design can lead to development of powerful systems capable of higher level control and optimization functions

Jan 1, 1981

By W. J. Deutsch, W. J. Martin, R. J. Serne

At the termination of mining, the quality of ground water in the ore-zone aquifer must be returned to a condition predetermined by the permitting agency. To immobilize the redox-sensitive elements (e.g., uranium, arsenic, selenium, molybdenum), it has been suggested that a reducing agent be circulated through the leached ore zone. We have conducted laboratory experiments to test the ability of sodium sulfide as such a reducing agent. Sodium sulfide lowered the redox potential of the effluent such that insoluble minerals containing the redox-sensitive elements should be stable. The uranium concentration of the solution decreased by more than three orders of magnitude. In column experiments, by the time 10 pore volumes of the sulfide solution had flowed through, sulfide minerals were forming. The experimental results indicate that the addition of sodium sulfide should cause chemical reduction of the leached sediments, thereby producing long-term stability of the ground-water/sediment system.

Jan 1, 1988

"?irovski Vrh" Uranium deposit in Slovenia is type of mineralized sediments in ore bearing belts of deflected S-structure, in which the belt is less than 25% mineralized. Ore bodies of irregular small thickness, unreliably contoured, made difficult estimation of correct contours, which are necessary for design and exploitation works. The deposit was explored by vertical boreholes made at the surface and by boreholes fanned from drives. For the purpose of application of this estimation method, 1 m composites have been made in slices which were parallel to the referential belt plane. Estimation was made for 1,5m x 1,5m x lm blocks which do correspond to the size of the containers in the ore transport stage. Two variables have been used: the first, indicator of function (ore=1, waste material =0) and kriging method; the second, logarithmical content of Uranium and Minimum Mean Square Error Estimation (MMSEE) method. Based on estimated values of those variables, probability of ore quantity as well as Uranium content over determined cut-off were calculated for each block. Those two parameters enable determination of the most probable form of the ore body in ecah one metter slice. Estimation of sixteen small blocks in a large 1,5m x 1,5m x 1m block made possible estimation of ore quantity and its content for the determined cut-off, as well as categorization of exploration. This method is being used for estimation of ore reserves and planning of exploration operations. The described' methodology was tested in an exploitation block.

Jan 1, 1986

By Adam Bezuijen, Tiago Gerheim Souza Dias

"The construction of mechanized tunnels in soft ground has evolved significantly over the last 20 years, especially in the control of the face pressure and the closure of the soil-lining void to reduce the induced settlements. On the other hand, several mechanisms of the TBM excavation cycle are still not taken into account for routine design calculations, such as the increment of water pressures in front of the tunnel face, the flow of excavation fluids around the shield, the dynamic equilibrium between the grout pressures and the excavation convergence, among others. This paper discusses specifically the issue of face pressures and how several mechanisms, which are routinely not considered, can be easily verified and incorporated into the state-of-practice of design. INTRODUCTION The stability of underground excavations is traditionally assessed through analytical solutions based on the lower bound theorem of plasticity (Atkinson and Potts 1977; Mühlhaus 1985) or the limit equilibrium method (Anagnostou and Kovári 1994; Messerli et al. 2010). These methodologies depend on the tunnel geometry, certain ground parameters and the support pressure. When conventional construction methods are used, the internal support pressure is an abstract representation of the combined effects of partial excavation, ground reinforcement, and the different support elements. The use of closed-face tunnel boring machines (TBM) changed this perspective, as the magnitude of pressures acting on the excavation boundary could be controlled in a more direct way. In front of the TBM the ground is excavated as the cutterhead rotates and the cutting tools scrape the ground from the tunnel face while additives are injected to condition the material. Water, polymers, bentonite, and foam can be used as additives under different conditions (Thewes et al. 2012). The loosened ground with additives, herein referred to as the mixture, flows through the openings at the cutterhead and into the excavation chamber. This mixture is kept pressurized to support the face."

Jan 1, 2016

International Minerals & Chemical Corp.'s New Wales operation near Mulberry, FL, is reportedly the world's largest concentrated phosphate chemical fertilizer and phosphate-based animal feed ingredients complex. Its latest expansion represents a $191-million investment. Two Northwest draglines were put to work at the operation early last year and, according to a company spokesman, total production from the units have more than doubled that from older rigs. This article describes how the draglines are used and provides details on the New Wales operation. The principle product at New Wales is phosphoric acid, produced by reacting ground phosphate rock with sulfuric acid in large concrete attack tanks. For each ton of phosphoric acid produced, New Wales must dispose of about 4.5 t (5 st) of waste gypsum. New Wales stores the gypsum on-site, and uses durable Northwest draglines to help handle the material. Two Units Maintain the Gypsum Stack After the gypsum is separated from the phosphoric acid through 23-m-diam (75-ft-diam) vacuum filters, it is mixed with water from a 121-hm2 (300-acre) recirculating cooling pond and, in slurry form, is pumped to the top of a 121-hm2 (300-acre) gypsum stack located adjacent to the cooling pond. The slurry contains mostly gypsum (CaSO4), with small traces of silica and other elements. The water at this point is corrosive, containing from 1-2% phosphoric acid. Its pH usually ranges from 1.5-2.0. Water drains from the gypsum stack into the cooling pond. Only about 15% of the pond's water, however, comes from the gypsum stack; the balance is from various sources throughout the complex and is held in the pond to cool before being returned for reuse in the plant. About 97% of New Wales' water needs come from this recycling program. The gypsum remains on the stack, inert, ready for future processing if it becomes economically feasible. Throughout the handling process, Northwest draglines work around the stacks' rim, continually directing the waste flow and digging out dried solids to heighten the perimeter dike to provide more storage volume. When wet, gypsum is extremely soft. When dry, it compacts well and provides footing with enough bearing capacity to support the machines. Processing at New Wales started in 1975 and the gypsum storage area has already been built up 12 m (40 ft) above grade. A total of 14.8 km3 (12,000 acre-ft) of solids are now stored. The draglines dredge material from near the perimeter dikes and place it to build parallel berms. This

Jan 8, 1982

By K. G. Wallace

In 1982, the US Congress passed the Nuclear Waste Policy Act (NWPA) to provide for the development of an underground repository for spent nuclear fuel. This development will be managed by the US Department of Energy. In 1986, the President selected three areas for site characterization to determine their suitability for the development of an underground repository. Those sites were: (1) a site in volcanic tuff located at Yucca Mountain in Nevada, (2) a site in bedded salt located in Deaf Smith County in Texas, and (3) a site in basalt located in Hanford, WA. At present, conceptual repository designs are being developed for each site. A key element of a repository design is the underground ventilation system required to support construction, nuclear waste emplacement, and potential waste retrieval. This paper describes the preliminary ventilation system designed for the repository in tuff. The concept provides separate ventilation systems for the construction and waste emplacement activities. The paper further describes the means by which acceptable environmental conditions will be reestablished to allow reentry into previously closed rooms for the purpose of inspection, maintenance, or retrieval.

Jan 1, 1988

By Barry N. Doyle, Tarcisio M. Carvalho, Alan K. Haines, Marcos P. de Melo, Edward J. da Silva

A metallurgical complex to recover gold from highly refractory arsenical ore was recently commissioned by Sao Bento Mineraco. The plant, with a nominal capacity of 20 000 tonnes per month, is situated in the Minas Gerais province of Brazil. The process consists of run-of-mine milling, flotation, pressure oxidation of the concentrate, carbon-in-leach, elution and electrowinning, and effluent disposal. The paper provides an account of the investigations that resulted in the decision to install the pressure oxidation circuit, process and engineering design and plant start up. A comparison is made between the results achieved during the first two years of production and the design parameters.

Jan 1, 1989

By R. L. Loofbourow

The Sunro Copper Mine is near the south coast of Vancouver Island about 35 miles west of Victoria. Failure of the roof of a large open stope let a good sized mountain stream into the mine. Broken are, boulders and sand were washed into the underground mill and out through a 7 800-foot adit. The adit became plugged; water burst out an a ridge above the adit, washing out the portal and o trestle by which it was reached, Rock and ore are strong but several systems of steep, pronounced but generally tight fractures are found on and parallel to the walls of the orebody. The stope was started from a slusher drift 390 feet below the bed of the River and brought up to an elevation 155 feet below the River by blasting vertical and horizontal rings of longholes in the nearly vertical orebody. Mining was stopped there and five months were given to grouting and bolting the pillar under the bed of the River, During this time and for several months thereafter sloughing increased the width, length and height of the stope. At the last known observation the stope was 77 to 96 feet wide, 185 feet long and the highest point of the domed back was only 55 feet below the River. The flooding took no lives. In other respects, however, it might be difficult to find in mining lore o more savage example of the application of "Murphy's Laws".

Jan 1, 1968

By Samuel S. Adams

Economic concentrations of potassium are essentially limited to thick, stratigraphic sections of marine evaporites. These deposits were precipitated through the evaporation of sea water in restricted epicontinental seas or in grabens related to continental margin rift systems. Following deposition the deposits were subjected to diagenesis and varying degrees of metasomatism and structural deformation. The origin and characteristics of potash deposits are easier to study and interpret than those of most ore deposits because the phase chemistry of the salt systems is known and the approximate composition of the ore-forming fluid (sea water) can be inferred with confidence. It is particularly helpful that the temperature and pressure of deposition approximated that of present earth surface conditions and the pertinent mineral assemblages can readily be duplicated in the laboratory. The study of these comparatively simple salt deposits provides examples of the practical advantages of understanding the genesis of an ore deposit. These observations, in turn, illustrate the importance of pursuing research on the more complicated magmatic, hydrothermal, and ground-water systems as a means to the more successful exploration for and exploitation of the deposits they have produced. It is the purpose of this paper, therefore, to discuss certain aspects of salt deposit geology as they contribute to exploration and mining through some understanding of ore formation. References to field examples and chemical relations in the salt systems are brief. All examples are more fully discussed, however, in the references cited.

Jan 1, 1970

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type, and causes of accidents in Turkish coal-extracting industries using Analytic Hierarchy Process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type, and causes of accidents. For this purpose, 1st, 2nd, and 3rd level hazards consisting of location, type, and causes of accident were determined by using the data of fatal mine accidents in underground and open-pit coal mining in Turkey between the years of 2010 and 2020. And then the data were categorized, and each category was prioritized using the AHP technique. According to the weights calculated by AHP, the most dangerous main criteria at 1st level hazards in underground coal mining is ventilation operations (0.363), while the most dangerous sub-criterion at 2nd level hazards is firedamp explosions and other gas accidents (0.409). On the other hand, in open-pit coal mining, the most dangerous main criteria at 1st level hazards are slopes and benches (0.575), while the most dangerous sub-criterion at 2nd level hazards are landslides (0.429).

Dec 30, 2023

By Greg Barfoot, Kurt Keskimaki

The Henderson Mine is located approximately 50 miles west of Denver, Colorado. A project is underway to replace the existing rail system which transports molybdenum ore 15 miles from the mine to the mill using three flight conveyor system. The first conveyor is a 1 mile, high lift conveyor which transports the ore from an underground crushing station to the end of the existing rail tunnel. The second conveyor is 10 miles in length and utilizes the existing rail tunnel to transport the ore from the mine, which is on the east side of the Continental Divide, to the mill located on the west side. The third conveyor takes ore from the tunnel portal to the mill through a series of 7 horizontal curves and inclines up to 15 degrees. The project applies advanced conveyor design to tackle the installation of the system in an operating mine and achieve the highest possible level of reliability. This paper outlines the design process for this system, discusses the options which were evaluated and how the current design evolved.

Jan 1, 1998

By Howard J. Haselhuhn

The effectiveness of selective flocculation and dispersion processes for the concentration of hematite ore are strongly dependent on the ionic content of the process water. It has been noticed that magnesium ions are more detrimental to iron recoveries during gravity separation and flotation processes than calcium. This phenomenon was studied by measuring the zeta potential of hematite ore at various concentrations of sodium, magnesium, calcium, strontium and barium at a pH of 11. Results show that zeta potential inverts from negative to positive at concentrations as low as 0.16 mM of magnesium ions in the solution. It takes a significantly higher concentration (1.25 mM) of calcium ions to achieve the same effect. This difference is attributed to the ability of magnesium ions to adsorb to all surface hydroxyl groups, whereas calcium, due to its larger size, can only adsorb to every third hydroxyl group. This hypothesis was confirmed by results similar to those seen with calcium when this test was repeated with strontium and barium ions. The tendency for calcium ions to adsorb to every third surface hydroxyl group causes higher concentrations of calcium to be less detrimental to hematite concentration processes than magnesium.

May 1, 2012

By Phillip J. Maddex

After the presentation of a co-authored paper, "The Cost of Transporting Ores and Raw Materials in World Markets", at the February SME meeting, one questioner commented, "You have been talking about the large shipper and ship loads. What does the small shipper do?" This paper will attempt to answer that question, at least in part. Probably the questioner hoped to hear about specific new tools and new techniques that he could apply. But one paper could only scratch the surface of the vast fund of information available; so rather than talk specifics we should take basics, that is, people, management and technology.

Jan 1, 1967

By Bahadir Ergener, Angel Maria Tobar Escudero, Sandra Nowosad

Modern mining companies are increasingly turning to integrate digital technologies and circular economy (CE) principles to increase the sustainability of their operations. The so-called “mine of the future” is envisioned as a smart, integrated system where technologies such as automation, artificial intelligence, digital twins, and real-time data analytics work in harmony with human decision-making and environmental responsibility. Already in 2018, McKinsey and Co. identified that the three drivers that would define a technology-enabled change in mining would be technology, including digital, analytics and automation, management systems able to identify the potential and value of the new technologies, and the culture and capabilities of the organisation, leaning to more agile and responsive organisations. From the three drivers, in the last five years most developments have been centred in the first one. Yet despite rapid advances, the adoption of new technologies across the industry today remains uneven and often slower than expected. Furthermore, it has been identified that the problem on the technology uptake often relay on the lack of operational readiness, process incompatibility or misalignment, and resistance to change within the mining operation. At the same time, leading companies like Rio Tinto, BHP, and Anglo American have each launched major digital transformation programs. Rio Tinto, for instance, operates one of the world’s largest autonomous mining fleets and has integrated digital technologies across nearly all its operations (Rio Tinto, 2025). BHP is actively investing in information and communication technology (ICT) development as artificial intelligence, big data analytics and robotics, and has partnered with battery companies to pursue circular economy initiatives. Only in 2024, their ICT spending reached US$ 438.3 million (Global Data, 2024). Anglo American has rolled out its FutureSmart Mining™ framework, explicitly aligning innovation with circularity and sustainability goals (Anglo American, 2025). The accelerating pace of change across leading mining companies along with the uneven adoption in the technology uptake clearly state how digital transformation is no longer just about implementing new tools, instead it requires a fundamental shift in how people, processes, and culture are aligned. Addressing only the technical layer, while neglecting the human and organizational dimensions, leaves transformation efforts fragile and unsustainable. As the industry must act decisively to close this gap, the true test of transformation is today centred in changing behaviours, mindsets, and systems. Even at the listed leading companies, initiatives have encountered cultural and structural resistance that are relatable to the industry in large: siloed departments fail to collaborate, procurement teams focus on upfront costs rather than lifecycle value, and operators are often excluded from early-stage planning, reducing buy-in. In many cases, a lack of communication or failure to link technology to real operational bottlenecks leads to disengagement at the ground level. This friction reveals a broader issue: mining organizations have historically treated technology and culture as separate domains, when in fact they are deeply interdependent. To address this, the authors propose a systems engineering approach focusing on the mining operations as a complex socio-technical system composed of people, processes, and technologies. Systems engineering offers tools and frameworks for mapping interactions, aligning incentives, designing for feedback and adaptation, and integrating change across organizational boundaries. Specifically, besides technical requirements, it demands treating culture not as an afterthought or side-effect, but as a design variable that must be intentionally shaped alongside infrastructure and workflows. This paper explores how this approach can be applied in practice, by analysing a real-world case scenario where resistance to innovation was overcome not by technical capabilities alone, but through alignment of stakeholder incentives, thoughtful communication, and cultural integration. A particular focus is set on the adoption journey of the Powerbit X, a drill bit technology with significant potential for operational and environmental gains.

Feb 22, 2026

By BARBOSA AMILTON, Denise C. R. Espinosa, David B. Dreisinger

Chelating resins can be used to recover important metals from different sources, and it is important to understand which resin is most suitable for each metal [1]. This review  benefits the mining industry because chelating resins can be used to recover metals from low-grade ores and mining tailings, increasing the industrial process efficiency [2–4]. Furthermore, the use of chelating resins in mining processes and mining tailings has the common problem of metals contamination, with iron being the main contaminant in low-grade ores and tailings. Understanding how contaminants decrease ion exchange efficiency is significant for industries [5

By Patricia Pride, Kurt Bettger, Jack Raymer

"INTRODUCTION The Jefferson Barracks Tunnel is in the final stages of design and is expected to go out to bid in the summer of 2016. The project is located in south St. Louis County along the west bank of the Mississippi River, about 13 km downstream of the St. Louis Gateway Arch. The project consists of a deep sanitary sewer tunnel, a deep pump station and several intakes. The intakes will divert sanitary flows into the tunnel and the tunnel will convey the flows by gravity to the Lemay No. 3 Pump Station, which will pump them up into the Lemay Waste Water Treatment Plant. The tunnel is about 5.4 km long and will be lined with 84-inch (2.1 m) fiberglass pipe. It drops at a gradient of 0.1 percent from south to north and will be bored through strong limestone using a hard-rock tunnel boring machine (TBM). The diameter of the TBM is anticipated to be about 3.4 m. The Owner’s original concept was for a relatively shallow tunnel so as to minimize construction and pumping costs. The preferred alignment ran close to the river, next to the existing force main, which was to be abandoned. Keeping the tunnel close to the force main would reduce the amount of shallow sewer work needed to connect the existing feeder sewers to the new tunnel. Several geotechnical investigations were performed, with shallowly focused geophysics and the borings all going exactly down the conceptual tunnel depth. Limestone bluffs run along the Missouri side of the river. These bluffs are pockmarked by sinkholes and riddled with karst. Large, well-known caves occur both north and south of the alignment. Karst features, including deep crevices and possible caves, were found in those early geotechnical investigations. Many of these features extended well below the level of the Mississippi River and would have been encountered by the tunnel. If a large crevice or cave were encountered, then the inflow of mud and water into the tunnel could have been large and possibly uncontrollable. Something had to be done to mitigate this situation. Pre-excavation grouting was considered, but the program would have been huge and extremely expensive. Using a closed-face TBM with bolted and gasketed lining was also considered, but that too was both risky and extremely expensive. The Owner could have abandoned the tunnel altogether and built a new force main, but that would have brought a whole new set of problems and was undesirable to the Owner. The last option was to move the tunnel away from the karst."

Jan 1, 2016

By William Harrison, Robert H. Trent

GENERAL DESCRIPTION History The most striking feature of mining in the United States has been the infrequent use of longwall systems. This system, which accounts for the majority of coal production in Europe, Japan, and other countries, is only recently growing out of its infancy in the mining of normal coal seams and is still untried in the mining of thick coal seams in the US. Its use in the mining of metal and nonmetal ore bodies has been virtually ig¬nored, except for isolated instances in trona, copper, and uranium. Longwall mining is believed to have originated in Shropshire, England, towards the end of the 17th cen¬tury (Laird, 1973). Although the method used would be considered primitive by today's standards, many of the basic concepts have remained unchanged. Longwall mining of coal in the US was first introduced before the turn of the century, but it never gained acceptance as it did in Europe. Historically, longwalling was a cyclic method where a single cut of coal was removed from the face on the producing shift each day, and the work of building stone packs in the gob and manually moving roof support was completed on the off shifts. Due to the amount of dead work, productivity was extremely low. In Europe, however, longwall methods were required despite the high costs involved, because only by this method could coal under heavy depth be mined with any reasonable degree of recovery. Reserves of coal lying under shallow cover, and therefore minable by room¬and-pillar methods, were long ago inadequate to supply most of Europe's coal requirements. In the US coal min¬ing has historically proceeded laterally with the new mines in virgin areas to replace old mines; in Great Britain, Germany, Japan, and many other countries, mining must proceed downward to greater depths. The depth of cover for most coal operations in the US is shallow, i.e., 61 to 305 m (200 to 1000 ft). This, combined with large reserves, has made room-and-pillar methods almost universally applicable. However, longwall systems were tried around the turn of the century. Whenever used, it was frequently noted that the opera¬tion was under the direction of men with foreign ex¬perience and was tried under ideal conditions. Some of the mines that were using longwall or had tried longwall prior to 1910 were the Radiant mine, CO; Vinton Coal Co., PA; Cambria Steel Co., Johnstown, PA; Grundy County and Spring Valley, IL; and unnamed mines in Washington, West Virginia, Kentucky, Iowa, and Kansas. As late as 1961, there was one circular longwall in operation at Centerville, IA. The first modern-day op¬eration to take advantage of European technology and longwall methods was Kaiser Steel Corp. at its Sunnyside mine near Price, UT. Due to deep cover and extremely poor roof conditions, combined with a need for in¬creased production, Kaiser management decided a new method was required and turned to longwall in 1961. The first longwall consisted of an Anderson Mavor shearer loader, British Jeffrey-Diamond conveying equip¬ment, and Dowty roof supports with a capacity made up of two and three 27-t (30-st) capacity props. After nor¬mal start-up problems, this unit averaged over 454 t (500 st) per shift (White and Palacios, 1976). During and after World War II, technology in hy¬draulics and controls had advanced to the point that self-advancing supports and hydraulic props were being developed. In 1960 only I % of West German produc¬tion was from mechanized longwall faces. This in¬creased to 37% in 1970 and 63% in 1973 (Kohlgruber, 1974). In 1976 there were 246 coal mines operating in the United Kingdom. Although this is only 50% of those operating ten years ago, the production has increased 42%, mainly through improvements in longwall equipment and methods (Hunter, 1976). In France and other European countries, the devel¬opment of longwall mechanization has been similar in seams up to 2.44 m (8 ft) thick. In seams that exceed 9.14 m (30 ft), a variety of longwall caving has been developed for coal seams with dips of 0 to 1.6 rad (0 to 90°). Those with the greatest success will be discussed later. As noted, the development of longwall mining to its present state of the art has mainly taken place since World War II with substantial gains in the last ten years. Mechanized longwall has been the result of several re¬lated major innovations (Jackson, 1975) 1) Development of the flexible armored face con¬veyor which can be installed along the face and moved forward without disassembly. 2) Development of face machines such as single and double drum shearer and coal plows which operate in conjunction with the armored conveyors. 3) Development of self-advancing hydraulic roof supports which now include chocks, chock shields, and shields. 4) Reliance of caving of the immediate roof based on proper planning and development. 5) Use of pneumatic slowing to enable extraction below overbuilt areas. The most recent developments in the mining of coal by longwall in the US include the introduction of shield supports at Kaiser's York Canyon mine in New Mexico, single-entry longwall development at Kaiser's Sunnyside mine, and Mid-Continent's advancing longwall system in Colorado. Metal and nonmetal longwall systems in the US have included the mining of copper at White Pine, MI; uranium in Utah and New Mexico, and trona in Wyoming.

Jan 1, 1982