Search Documents

By W. K. Summers

During the past few years monitoring systems have been installed to measure the effects of environmental changes on the ground-water resource. The design of a monitoring system depends upon the designer's perception of how the environmental factors merge with his perception of the ground-water flow system. The validity and representativeness of measurements made during a monitoring program depend upon the validicy of the designer's perceptions and concepts. To optimize the design of a ground- water monitoring program the designer should make preliminary measurements to confirm his assumptions.

Jan 1, 1985

By Bill S. Taylor

Dutch State Mines [D.S.M] introduced the Heavy Medium Cyclone into the United States for cleaning fine coal about three decades ago. Since that time the general industry practice has been to deslime the raw coal at 28 Mesh (0. 59mm) size. The plus 28M material is fed to the Heavy Medium Cyclone for cleaning, and the 28M x 0 fraction is processed by other means (e. g. flotation or hydrocyclones). This approach recognized that 28M was the smallest size particle that could be easily rinsed on vibratory screens without excessive loss of magnetite, and without blinding of sieve bend and vibratory screen decks. Another reason for the 28M de-sliming was to avoid excessive contamination of the media with non-magnetic coal, shale, or clay fines. The most undesirable of these contaminants is the sub-micron size clay particles (2) that greatly increase the viscosity of the media and reduce the numerical maximum level that the media specific gravity can obtain due to the lower specific gravity of clay with respect to magnetite. The higher the fugitive clay content, the more severe the preceding problems become. During the last 30 years, many conventional Heavy Medium Cyclone Plants have been built throughout the world. In the United States, the initial cyclone plants were confined to the production of high quality metallurgical coal where lower gravities of separation were required than could be obtained from the conventional hydraulic or air separation processes. In recent years a large and ever-increasing number of preparation plants producing steam coal have started utilizing Heavy Medium Cyclone technology due to the environmental pressures being encountered to produce low sulphur coal. Due to the inherent characteristic of many coals of having a lower pyritic sulphur content at lower specific gravity fractions, many applications and markets are appearing for separating steam coals at much lower specific gravities than have been historically normal in the United States. Therefore. Heavy Medium Cyclones are being utilized to a much greater degree in this field, due to the flexibility of low separating gravity ability coupled with high efficiency when high percentage of near gravity material is present.

Jan 1, 1978

By Hasan Nizamoğlu, M. Deniz Turan, MÜCEVHER TURAN, RAMAZAN ORHAN

Tailings (flotation waste) that is formed during copper production may be considered in the class of valuable wastes due to the amount of copper it contains. Owing to the decreasing grade values in copper ores, utilization of wastes such as tailings that carry certain amounts of copper as secondary sources has become a necessity in both the economic and environmental sense. This study investigated the usage conditions of five different ammonia salts as leaching reactants for the purpose of selective extraction of copper from tailings. For this purpose, the effects of parameters such as leaching temperature and leaching time were examined at different concentrations of ammonium hydroxide, ammonium carbonate, ammonium nitrate, ammonium chloride, and ammonium persulfate. The copper extraction efficiency in the case of using the aforementioned salts by themselves were listed as (NH4)2CO3 (73%) > (NH4)2S2O8 (69%) > NH4OH (64%) > NH4Cl (42%) > NH4NO3 (40%). The highest copper extraction efficiency was obtained in the leaching process that was conducted with the solutions obtained by mixing ammonia salts in the best conditions. Accordingly, as a result of 6 h of leaching at 30 °C in the presence of 22.5% NH4OH and 100 g/L (NH4)2S2O8, 91.47%of the copper was transferred into the

Jun 3, 2020

By Ali Ekrem Aritan

Exposure to hand-arm vibration (HAV) among the labor force in the mining industry can result in permanent vibration diseases such as behavioral disorders, visual impairment, osteoporosis, pain (mostly in the hands, wrists, and shoulders), circulatory system disorders, and malnutrition. In this study, the vibration exposure of excavator operators working regularly in 25 different natural stone quarries was measured. In addition, the relationship between vibration exposure and rock properties was investigated. Gloved and ungloved vibration measurements were performed and revealed that antivibration gloves reduce excavator operators’ vibration exposure by 7.10–25.95%. Samples from each quarry were characterized with rock mechanics tests. The correlations between the hand-arm vibration measurements and the natural stone physical–mechanical properties (uniaxial compressive strength, Shore hardness, Knoop hardness, apparent density and total porosity) were determined to be over 70%. One finding of the study was that the health risk in excavators cannot be reduced sufficiently by the sole use of antivibration gloves. Furthermore, the excavation of any rock with a Knoop hardness above 121 is associated with an 81% risk of HAV. To increase awareness of the danger of vibration exposure for natural stone miners, training programs should be provided, and technical and operational changes should be implemented.

By Ali Ekrem Aritan

Exposure to hand-arm vibration (HAV) among the labor force in the mining industry can result in permanent vibration diseases such as behavioral disorders, visual impairment, osteoporosis, pain (mostly in the hands, wrists, and shoulders), circulatory system disorders, and malnutrition. In this study, the vibration exposure of excavator operators working regularly in 25 different natural stone quarries was measured. In addition, the relationship between vibration exposure and rock properties was investigated. Gloved and ungloved vibration measurements were performed and revealed that antivibration gloves reduce excavator operators’ vibration exposure by 7.10–25.95%. Samples from each quarry were characterized with rock mechanics tests. The correlations between the hand-arm vibration measurements and the natural stone physical–mechanical properties (uniaxial compressive strength, Shore hardness, Knoop hardness, apparent density and total porosity) were determined to be over 70%. One finding of the study was that the health risk in excavators cannot be reduced sufficiently by the sole use of antivibration gloves. Furthermore, the excavation of any rock with a Knoop hardness above 121 is associated with an 81% risk of HAV. To increase awareness of the danger of vibration exposure for natural stone miners, training programs should be provided, and technical and operational changes should be implemented.

By Kwadwo Osseo‑Asare, Isehaq Al‑Nafai

The hydrometallurgical processing of bastnasite is a well-known process that is used to extract rare earth metals. However, more accurate measures are required to enhance the efficiency of extracting and recycling rare earths. In this work, Pourbaix (Eh–pH) diagrams for La-, Nd-, and Pr-(F)-(CO3)-(SO4)-(Cl)-(NO3)-(C2O4)-H2O systems were theoretically derived to investigate the stability relations during the hydrometallurgical processing of bastnasite. The diagrams for RE-H2O systems show similar trends to the original ones drown by Pourbaix. The stability domains of RE carbonates were presented by RE-CO3-H2O systems with pH range of 4.5–11. In contrast, the diagrams for RE fluorides showed a large stability region of insoluble REF3 (pH ~ − 1.7–12). The decomposition behaviors of REFCO3 were studied by constructing Eh–pH diagrams for RE-F-CO3-H2O system. The stability regions of bastnasite species extend from nearly neutral to basic media (pH ~ 6.5–12). The acid treatment (using H2SO4, HCl, and HNO3) of bastnasite was investigated by constructing Eh–pH diagrams for REF- CO3-(SO4)-(Cl)-(NO3)-H2O systems. According to these systems, REFCO3 can be decomposed at pH ~ 6.5 when treated with H2SO4 and at pH ~ 1.7 when treated with HCl and HNO3 acids. On the other hand, the alkaline treatment of REFCO3 converts it to RE(OH)3 at pH ~ 11. The recovery of rare earths ions was studied with the aid of RE-C2O4-H2O systems which shows a wide stability region for RE oxalates in pH range of − 2–11. This theoretical approach explained the aqueous relations in the hydrometallurgical processing of bastnasite ore and it can improve the practical hydrometallurgical processing of such ores.

Feb 9, 2024

By R. K. Devala

In this paper, numerical approximation schemes, for solution of the mass transfer problem in mine ventilation have been developed by using three implicit finite difference schemes. Results from these schemes have been compared with the analytical solution for spatial and time increments, using the concept of Root Mean Square error. For implicit finite difference schemes, in general, the modified central difference scheme is better than the two other schemes at lower velocity. Also, at lower air velocities, implicit schemes underpredicted the concentration values. At higher air velocities, the Crank-Nicholson and Laasonen schemes provided better results than the Modified Central Difference scheme.

Jan 1, 1994

By SANDEEP KUMAR JENA

This paper reviews the recovery of potassium from different rocks and mineral sources. Global demand for potassium is rising steadily due to the growth of agricultural production. Fertilizer manufacture consumes the majority of the world’s potassium production, with other uses including those in the pharmaceutical, glass, ceramic, food and detergent industries. The availability of soluble potash (K2O) minerals, such as sylvite, kainite and carnalite, in countries like Canada, the United States, Israel and Russia makes them major potash producers, whereas agriculture-based countries like Liberia, Somalia, Central African Republic, Thailand, Indonesia, Malaysia and India meet their potassium requirements through imports only. In these countries, the huge availability of potassium-bearing rocks/minerals like nepheline syenite, feldspar, mica and glauconitic sandstone, containing around 4 to 17 percent K2O, brings up the prospect of commercial production of potassium. Potassium recovery from minerals/rocks is complicated due to the uniform distribution of potassium throughout the crystal structure. Different physico-chemical separation methods like bioleaching, chemical leaching, flotation and roast-leaching have been discussed for the successful recovery of potash values from these rocks/minerals. Although seawater is vastly available, the recovery of potassium from seawater using chemical precipitation, solvent extraction, membrane separation and ion-exchange methods is not cost-effective due to low concentration of potassium.

By R. S. C. Rogers

A mathematical model is proposed as a general formulation for the analysis and simulation of once-through crushing machines. Methods are described which can be used to estimate parameters of the proposed model from experimental data, thus minimizing reliance on backcalculation. The applicability of the model is demonstrated in the analysis and simulation of laboratory and full scale double roll crushers, and with evidence given for a laboratory scale cone crusher. An extension of the model for closed circuit crushing is also described.

Jan 1, 1984

By R. J. Heath

Potash, the general term for potassium salts used as fertilizers, is one of the essential growth nutrients (together with nitrogen and phosphates) required by all living things. Total world consumption of potash for fertilizer use - almost all of it in the form of potassium chloride - amounted to an estimated 47 million short tons in the 1979/80 fertilizer year*. While there is some limited demand for potash for a variety of industrial applications, this amounts to only 3 or 4 per cent of total world demand, and the potash business can be viewed as essentially a fertilizer business. Total available world potash production in the 1979/80 fertilizer year also amounted to approximately 47 million tons. There are two large potash producing countries - Canada and Russia - and a number of other countries where production is significant - East Germany, West Germany, the U.S.A., France, Israel and Spain. Production volumes are shown in Table 1.

Jan 1, 1980

By D. Goffaux

In less than two years, Stratmin has discovered, explored, developed, financed and put into production by open pit, a large graphite mine. The deposit, hinted by airborne electromagnetic survey, was discovered in September 1987 through various ground geophysical surveys, diamond drilling and trenching. The open pit started production in February 1989, feeding a nearby leased mill at Notre-Dame-du-Laus (Quebec), having a processing capacity of 400 tons per day. A new 1,000 tonne per day mill was built at the mine site, in Lac-des-lies (Quebec) and began production in April 1990. The Lac-des-lies graphite operation is currently one of the largest of its kind in the world. Mine and mill facilities are operated by Stratmin Graphite, jointly owned by Stratmin Inc. (75%) and Imetal-France (25%), a wholly owned subsidiary of Imetal (France). From initial exports limited to Japan and United States, Stratmin Graphite is now exporting in fourteen different countries, attesting to the very high quality of its products, with grades ranging from 92% to 97% carbon. Among the numerous graphite deposits discovered in Canada, Stratmin Graphite Inc. has emerged as the leader and virtually the sole crystalline graphite producer in North America, operating on a continuous basis.

Jan 1, 1992

This paper reports on the behavior of mercury and its compounds during the thiosulfate leaching and recovery of gold. Thiosulfate solutions are shown to dissolve Hg0 and Hg2Cl2 to a similar extent as cyanide, but the leaching of HgS is significantly slower in thiosulfate solutions compared to cyanide. Hence, the use of thiosulfate may be an option for treating ores containing high levels of cinnabar, especially since the legislation concerning the discharge or sale of mercury is becoming more restrictive. The deportment of mercury during gold thiosulfate loading and recovery using a strongly basic anion-exchange resin was also studied. Although the mercury thiosulfate complex loads on the resin, the adsorption is weaker than for gold, with an equilibrium constant between gold and mercury of 51. Resin loaded with gold, mercury and copper was pre-eluted with thiosulfate (to remove copper) and eluted with a chloride and sulfite eluant. The majority of the mercury is eluted by the eluant and, hence, its deportment closely follows gold and the eluate would need to be treated to remove either mercury dur-ing or prior to gold electrowinning.

Jan 1, 2010

By John C. Harkey

The paper shares programs that presently use the CDC PLATO System to train individuals in industry. A short history of PLATO development; as a training system is presented with reflection on the major training trends being used to improve training effectiveness. A discussion is offered to describe the benefits of using a system for individualizing instruction. An introduction; is offered showing how one can recognize' individual differences, with an explanation of how the strengths of a computer are used to deliver and manage the training. Simulations of hazardous processes are shown to be one of the most effective uses of the computer for training.

Jan 1, 1979

By William E. Mead

Although this paper has been entitled "Design of Embankments for Tailings Ponds and Waste Dumps," a better title might have been "Site Selection and Design Planning for Tailings Ponds and Waste Dumps," The procedures normally followed in performing the engineering calculations based upon the measured soil properties will not be detailed. Instead, we shall look at the subject in broader perspective which considers the environmental factors and the fundamental design principles. Disposal of waste materials left from the extraction and processing of mineral deposits has become, in recent years, an important engineering consideration for mine and mill operators. Land occupancy and land values almost everywhere are increasing at a rapid rate. So is the size of mine and mill waste dumps, thanks to our advancing technology in mineral beneficiation. Mining companies are being pressured to "clean up" their operations, both literally and in a safety hazard sense. Once, long ago, the miner could use any convenient location to get rid of his mine waste and mill tailings without being concerned over possible infringement on the rights and well-being of the public. Today, however, he must pay close attention to these matters if he wishes to avoid liability suits and the unfavorable reaction of civic groups as well as local and regional government. Most operators keenly sense their increased responsibility, not only because they are legally vulnerable, but because they realize the necessity for sharing space harmoniously with the rest of society.

Jan 1, 1967

By J. H. Wilhelm

Continuous thickeners can be sized either from previous experience, continuous pilot-scale test results, or from batch settling tests. Although it is a relatively simple process to size full-scale thickeners when previous experience or pilot-scale operating data are available, batch testing is often the only realistic method for sizing thickeners due to time restrictions, budget limitations and availability of sample material. Many authors have, therefore, suggested means of running batch tests and analyzing the resulting data. Fundamental thickening theory had its beginning with the work o£ Coe and Clevenger(1). In order to determine the size of the thickener settling area, they proposed that a series of batch settling tests be run at various initial concentrations. The solids handling capacity at each concentration can then be determined and the lowest capacity (maximum area requirements) used to size the thickener. Kynch(2) developed a mathematical analysis in which the relationship between solids concentration and settling rate can be obtained from a single batch settling curve. Talmage and Fitch(3), Yoshioka(4)(5) and Dick(6), have enlarged upon these works to give a basis for methods of sizing thickeners.

Jan 1, 1979

By R. O. Y. Breese

Perlite is a hydrated acid volcanic glass that has been derived from the alteration of obsidians through incorporation of water into the silica structure. It is distinguished from other members of the water-bearing natural glass family by total water content, characteristic fracture and luster. The distribution of major occurrences worldwide is associated with silicic Tertiary through early-mid Quaternary volcanics related to plate movement. The No Agua dome and flow complex is one of the most highly studied perlite occurrences in the world. It clearly exhibits lithologic and textural zonations that reflect simple cooling history. Similar features are commonly observed within other perlitized, extrusive glass selvages. This paper briefly discusses current thought regarding geologic occurrence, the hydration process and the modes of origin with special emphasis on No Agua.

Jan 1, 1985

By R. K. Mehta, G. T. Adel

A review of the literature reveals that methods for simulating the coupled behavior of size reduction and liberation are limited to binary mineral systems containing one composite particle class. The aim of this paper is to describe the development of a mathematical model to simulate such behavior for binary and ternary systems containing multiple classes of composite particles. A modified Levenberg-Marquardt algorithm and a finite difference Jacobian are used in conjunction with the developed model and a set of constrained equations to estimate all kinetic parameters. This estimation scheme is validated far a binary ore (sphalerite-dolomite) with five composite particle classes using experimental data.

Jan 1, 1991

By Stephen C. Moore

The Grossschloppen vein-uranium deposit, Bavaria, West Germany, was examined utilizing underground workings during 1980-82 by Esso Erz GMbH, an affiliate of Exxon Minerals Company (EMC). Geologic evaluation entailed dense drilling of a portion of the deposit from workings constructed specifically for the program. Discovered in 1977, the deposit was initially explored by surface diamond drillholes which allowed definition of a 30-60 m wide vein system discontinuously mineralized along a 1000 m strike length and to at least a 450 m depth. The underground program was conceived as a cost effective procedure to answer questions on vein correlation, grade continuity and variability. A 1200 m decline allowed access for detailed sampling of approximately 10% of the known area of mineralization. Fanned drillholes, logged by gaga probe, were spaced to provide intersections of veins at 10 to 20 m intervals. Six cross cuts also penetrate the pitchblende and uranophane mineralization which occurs in 0.1 to 2.5 as thick quartz veins. Detailed cross-sections and level plans were constructed for resource estimates of the intensively studied portion of the vein system. The program resulted in the discovery of local, high grade areas and an average grade in the evaluated area nearly double that expected from surface drilling.

Jan 1, 1983

By Roger G. Haga, Richard P. Campbell

Introduction Project scheduling . . . . • What is it? • Why is it done? • Who does it? • How is it done? • When is it done? These are some of the questions that will be addressed in this paper. It is intended that by exploring these questions, an understanding of project scheduling, its purpose and benefits can be achieved. The purpose of this article is not to describe in detail "how to schedule", but rather to give an overview of the scheduling function on a project. A successful scheduling effort is dependent upon the people responsible for developing, implementing, and monitoring the schedule, and the tools and procedures that are used. These three elements are integral components of project scheduling. What is it? A schedule is the integration of network relationships, resource constraints and the calendar. The schedule identifies when the activities "will" be done, while the network states when they "must" be done. Networking techniques are the most widely accepted scheduling tool for complex projects. The benefit of the network is the simplicity in illustrating, presenting and analyzing the dependency relationships of a project. The logic network is the foundation of the schedule. When calendar dates are applied to the logic network, it becomes a schedule which provides the basis for evaluation of project status, forecasting the occurrence of events and controlling the project. The sequence of activities that requires the longest time to complete determines the overall duration of the schedule. This longest sequence of activities is called the "critical path". The "critical path method" (CPM) is used to describe this particular schedule network methodology. The two common conventions of CPM networks are the "arrow diagram met hod" (ADM) and the "precedence diagram method" (PIM). There are arguments in favor of each of these two methods, and usually the one that is used is a matter of personal preference, project directive or corporate procedure.

Jan 1, 1986

By N. D. Cristescu

The aim of the present paper is to show how a mathematical modeling of a creeping rock and that of an yieldable lining can allow us to obtain an optimization of the lining design and generally of the whole procedure and sequence of excavation-lining application. We follow the procedure presented by Cristescu (1989) Chap. 13, and Cristescu et al.(1987); for some other approaches see the literature mentioned, for instance, by Ladanyi and Gill (1988). We have in mind to describe the creep of the rock, i.e. the tendency of the tunnel to close in time, and to take into account that the lining itself may be deforming, i.e. possesses some rheological behavior. We start from the well known fact that "intelligent" lining, which are yielding to the pressure of the rock, may be much more successful in supporting creeping rocks than excessively strong, badly designed supports which are unable to resist to pressure of the rock, though these are oversized supports (too strong, too stiff, installed too early, etc.). In order to optimize the lining to be used for a certain rock, it is absolutely necessary to study in the laboratory the main mechanical properties of that specific rock and to formulate for it a reasonably simple mathematical model. Standard triaxial test results are quite enough to determine the model for the rock, combined with some creep tests which have to reveal the long-term behavior of rock (the so-called rheological model). What concerns the lining, we consider several kinds of linings existing today, for which a mathematical model was also formulated. One shows which is the interaction between the creeping rock? and the yielding lining and how can it be formulated in mathematical terms. Once written in mathematical terms, an optimization of the lining design and that of the excavation layout and support application sequence is possible. We will try to make the exposure as simple as possible, avoiding details and having in mind to give only a sketch of the problem, while the mathematical details could be worked out quite easy.

Jan 1, 1994