Search Documents

By Mike S. Ness, Allan G. Provost

High speed drilling, mucking, and hauling equipment was used in driving approximately 2.16 km(7100 ft) of lower power tunnel in quartz diorite for the Tyee Lake Hydroelectric Project near Wrangell, Alaska. The .91 m(36 in.) guage rail mounted equipment included a Tamrock 2-boom electric/hydraulic drill jumbo, a Haggl and 8HR mucker , and 3 Hagglund 115C shuttle cars. Several other innovative techniques allowed maximum advance rates of up to 17.5 m/day(57ft/day) in the 3 m(10ft) horseshoe section. Average tunnel advance was approximately 11 m(day(35.4 ft/day). The primary difficulties preventing full utilization of the equipment potential were the operators' "learning curve", the need for complete retraining of all personnel in the new methods, and minor sections of faulted ground.

Jan 1, 1983

By Brian P. Canning

Ion exchange resin processes are receiving renewed attention in the mining industry for recovery;, of metals from solution. This interest has been inspired by the development of continuous countercurrent ion; exchange systems (CCIX) which are of much lower cost than the original, fixed bed contactor processes. With the countercurrent systems and new developments to process or upgrade the eluate product, ion exchange can now compete successfully with solvent extraction for treatment of uranium ores. The low concentration of U308 obtained in the CCIX strong eluate is generally upgraded by solvent extraction methods in sulfuric acid systems. Resin loadings of up to 120 grams per liter of U308, however, have been produced experimentally by recycling of eluate (HIM-IX process) and further developments may be expected in the near future. New developments in resin technology are bringing forth products of greater strength, loading capacity, selectivity and density. Densities up, to 1.35 spgr have been claimed by some suppliers. The process is not a new one and has taken years to advance to the present state of development. The earliest system to gain widespread acceptance was the resin-in-pulp system applied to uranium recovery. Ion exchange, however, later lost acceptance in favor of solvent extraction in the 1960's due to problems in resin degradation, resin contamination and resin-pulp separation, in addition to the development of improved solvent extraction reagents and techniques. The resin-in-pulp system continues to have application on high clay ores and has advanced in design. A number of other continuous ion exchange systems were also tried but never gained continued acceptance. In the current resurgence period the CCIX systems to gain acceptance were the Utah and Chem-Sep (Higgins Loop) systems. These processes are relatively simple in concept although require sophisticated controls. Fixed bed columns have also been designed into multistage systems in countercurrent operation but are not discussed in this paper. These systems remain competitive today for many applications. The most recent advancements however have been in the multistage contactors from,, which three are in current acceptance. These are the Himsley, Porter, and NIM systems. All industrial applications of these systems are relatively new, although pilot plant and in-plant development has been in progress over the last decade. Fur36ther developments should be expected in the near future.

Jan 1, 1979

By W. Stahl, K. Keller

In addition to classifying bulk material, vibration screens are commonly used in dewatering. However, the lack of a comprehensive physical theory of dewatering often leads to difficulties in the design and operation of the vibration screens. First, in this report, the dewatering of bulk material are shown based on a physical model. Because of tile oscillatory motion of the liquid in the bulk, the inertial force of the accelerated liquid and the dripping of water out of the bulk or screen must be taken into special consideration. The physical model put forward shows the effect of the various operations parameters of dewatering screens. A comparison between dewatering theory and practice are shown by measurements using coal, limestone, etc. Dewatering measurements conducted on a vibration screen demonstrated that different vibration frequencies and rates of acceleration lead to different residual moistures. Finally, the possibility of improving vibration dewatering is described.

Jan 1, 1998

By J. W. Choung, J. A. Finch

Acid rock drainage (ARD) is a recognized environmental challenge facing mining industries. An ambient temperature ferrite (ATF) process has been investigated for treating ARD. Most nonferrous metal and calcium ions present in typical ARDs were found to be detrimental to the ATF process. Three approaches were examined, including C02 aeration, addition of complex agents and use of magnetic seeds. By introducing magnetic seeds in the ATF process, the interferences were minimized and all the precipitates formed with lime neutralization were magnetically recovered from a simulated ARD. The residual concentrations of major metal ions in the treated water were environmentally acceptable. The XRD pattern confirmed the spinel ferrite crystal structure of the products

Jan 1, 2000

By Chuck R. McLendon

A new face ventilation system was needed at the Allied Chemical Trona mine, near Green River, Wyoming. The development of an exhaust manifold face ventilation system came from a need to reduce the dust and noise concentration level while maintaining methane control at the continuous miner working face. Dust laden air from a heading being driven by a continuous miner was contaminating the intake air in the mine around the roof bolter operator and adjacent headings. Each working heading was exhausted into the last open crosscut by a face fan. A face fan would contaminate the adjacent downstream heading with dust-laden air until a high dust concentration developed in the final entry before the returns. A face ventilation system was needed to give the exhaust of each heading an individual path to the return air. In addition, the system could not interfere with the present room and pillar mining process. A manifold system of rigid duct ventilation tubing was designed using the existing fans in a parallel arrangement. Each system was to consist of the rigid duct tubing in three headings junctioned together at the last open crosscut and exhausted at a common branch in the return air. Each heading was to have its own damper (or valve) so that air could be directed where it was most needed. The system was installed using both round and oval rigid duct ventilation tubing to minimize head loss and to allow proper ground clearance for mining machinery. Two fans in parallel were used to exhaust three headings. By adjusting the valves at each heading, up to 18.0 kcfm (9.36 cu m per sec) could be exhausted from one heading and still keep the methane level controlled in the other two headings. The manifold exhaust system has proven to be an efficient, long lasting ventilation system at the Alchem Mine. It has reduced the dust and noise exposure levels at the working faces while keeping the methane level under control.

Jan 1, 1980

By F. Kitzinger

The possibility of increasing the efficiency of mineral processing plants by means of computer control has prompted metallurgists to examine their flowsheets more critically in order to develop practical control strategies. Control schemes in use to date generally rely on the automation of traditional and previously manually regulated control loops, for instance the addition of reagents to maintain a constant assay or a constant pH. This approach is predicated on the availability of well-established primary sensors such as pH electrodes or on-stream analyzers. Noranda Research Centre, in cooperation with Noranda Group concentrators, has developed a froth level monitor and a pulp density meter susceptible of application in this type of control. Although some of the basic principles on which they are based have been known for some time, their incorporation into the design of reliable, direct-reading instruments which can be interfaced with a computer, is be-lieved to be novel*.

Jan 1, 1977

By J. G. Russell

The valuation of known mineral re-serves entails the economic evaluation of the mining enterprise and the valuation of other assets employed, including mining and processing plant and intangible assets. A case study approach analyzes two reserve situations: ownership of reserves (phosphate rock), and leasing of reserve lands (kaolin). The appraisal of the physical property is outlined, along with the economic analysis of the operation. The discounted net cash flow approach is used to value the enterprise, leading to value of the reserves after correlation with other assets employed.

Jan 1, 1989

By C. E. Capes

INTRODUCTION In the coal industry, ever greater amounts of fine coal must be processed due to the need to crush to finer sizes for impurity liberation in low cost physical cleaning processes. Fine coal processing is a major problem for the industry, both through the cost of disposal of reject fines and through the mining cost of lost coal values. Of the available disposal methods, impoundment has always been the most popular. In many cases, when the coal fines were of sufficient quality, froth flotation and expensive filtration methods were used to recover the coal in these waste streams. The coal fines are not always of a marketable quality, however, and flotation, due to poor yields and difficult dewatering, has always been an expensive and not necessarily profitable process. The oil agglomeration method is increasingly important as a technology for the treatment of fine coal-in-water suspensions. These fines can be preferentially wetted and agglomerated by many different oils mixed with the suspensions. Ash-forming impurities remain in suspension and are rejected when the agglomerates are recovered, for example, by screening. Agglomeration-based methods provide perhaps the only practical means for upgrading extremely fine coal to useful products on a large scale. As with froth flotation, oil agglomeration relies on differences in the surface properties of coal and impurities to effect separation. Whereas flotation be- comes less effective with particles finer than 200 mesh (0.075 mm) or coarser than 50 mesh (0.3 mm), there appears to be no lower limit on particle size for oil agglomeration while particles % in. (3.175 mm) diameter or larger can also be treated, if desirable. In addition to this ability to clean a broader size range of coal particles, oil agglomeration can produce a dense, coarse granular product of acceptable strength and low water content without the need for vacuum or thermal drying. The preferential wetting of solid surfaces by immiscible liquids has been utilized, if not fully understood, for a long time. Indeed Gaudin,229 in tracing the ancestry of froth flotation, refers to a 15th century oil-pulp kneading procedure in which water-wetted particles were freed under water from an oiled mass. An understanding of the physical chemistry involved in such

Jan 1, 1991

By G. Purcell

When coal in an oil/water slurry is ground to minus-200-mesh in a ball mill, some of the mill energy, normally wasted as heat, can be usefully recovered to help emulsify the oil. If the discharge flows onto a suitable sized trommel screen, water and ash material are rejected through the screen while coal and oil ball together to give a clean coal product. A small (6-lb/hr) continuous plant has demonstrated the feasibility and the limitations of this process for New Mexico coals.

Jan 1, 1980

By Mark R. Stanton, Douglas B. Yager

Integration and synthesis of mine-site topography, geophysical, and geochemical data yields both two- dimensional and three-Amensional perspective models for the May Day mine located in the Cement Creek drainage near Silverton, Colorado. Induced polarization, geophysical data are spatially registered with geochemical data acquired from drill hole cuttings that are contoured m three-dimensional space, thereby permitting determination of the most metalliferous and sulfur rich zones of a waste pile. This spatial modeling application was developed to be a visually intuitive tool to aid in mine waste reclamation.

Jan 1, 2000

By W. K. Wedge

The chemical composition of the Pennsylvanian Bethany Falls Limestone Member of the Swope Formation was investigated using optical emission spectroscopy and both flame and flameless atomic absorption spectroscopy. Elements determined were Ca, Mg, Fe, Mn, AI, Si, Na, K, P, Ti, Zn, Cd, Ni, Co, Cu, Pb, Cr, V, and Mo. Over 100 samples were collected from active quarries along a 320-km-long (200-mile) outcrop in northwestern Missouri. Intervals were sampled representing uniform lithology to determine vertical and lateral geochemical variation. The Bethany Falls Limestone is the most extensively quarried Pennsylvanian limestone in Missouri. In 1975, 42 active quarries produced almost 5.4 million tons (6 million st) of stone valued at over 15 million dollars.

Jan 1, 1977

By Michael Li

Unsaturated flow and solute transport were studied in three large columns measuring 1.5 m diameter x 2 m height, loaded with up to 3.7 t of oxidised waste rock, which was excavated from the Stratmat pile at Heath Steele Division, Noranda Inc. and contained elevated concentrations of zinc in the pore water. The bottom of each column was partitioned into 37 squares, each of which was drained independently. Following rain simulations at the top of the rock bed, the drainage in each drain port was monitored for volume and physicochemical parameters at pre-determined intervals. This paper describes some of the observations resulting from the experiments. The main conclusion of the study is that unsaturated flows in waste rock are heterogeneous, and flow channelling is ubiquitous. The results imply that the transport of solutes from oxidised waste rock to its toe drainage is subject to various controlling mechanisms, including geochemical equilibrium control and successive pore water dilution control.

Jan 1, 2000

By Natasa Mitevska, Predrag Djordjevic, Zivan Zivkovic

This paper presents the results of an experimental investigation into the distribution of copper in the slag of an industrial reverberatory furnace sulfide concentrates smelting process in the copper smelter RTB Bor (Serbia). The influence of copper content in the matte, the temperature and the height of the slag on the content of copper in the slag was determined as Cuoxide, Cusulfide and Cutotal and was based on possible mechanisms for the loss of copper in a silicate slag from the smelting of sulfide copper concentrates. The greatest quantity of copper in the silicate slag was found in the form of matte particles, which were captured in the slag as a result of the “flotation” of SO2 gas which was formed by magnetite reduction with FeS at the slag–matte interphase boundary.

By Natasa Mitevska, Predrag Djordjevic, Zivan Zivkovic

This paper presents the results of an experimental investigation into the distribution of copper in the slag of an industrial reverberatory furnace sulfide concentrates smelting process in the copper smelter RTB Bor (Serbia). The influence of copper content in the matte, the temperature and the height of the slag on the content of copper in the slag was determined as Cuoxide, Cusulfide and Cutotal and was based on possible mechanisms for the loss of copper in a silicate slag from the smelting of sulfide copper concentrates. The greatest quantity of copper in the silicate slag was found in the form of matte particles, which were captured in the slag as a result of the “flotation” of SO2 gas which was formed by magnetite reduction with FeS at the slag–matte interphase boundary.

By T. N. Andersen

The history of gold and silver analyses shows an interesting duality. On one hand, classical chemical and instrumental methods have evolved to meet changing needs, but on the other hand, the age-old and somewhat empirical fire assay has remained a popular tool. Inasmuch as gold and silver generally have been present in ores at low concentra¬tions, methods have been challenged by a need for sensitivity and selectivity coupled with reasonable assay time. A progressive increase in the importance of low grade materials as ore sources has led to the need for improved methods. Assays of these materials are required for process control and accounting in operating plants as well as for guiding research and development activities. The analytical response to these needs is evidenced by numerous reviews published through 1977-¬e.g., cf Kolthoff and Elving (1966), Beamish and Van Loon (1966, 1972, and 1977), Young (1971) , Mallett (1970), and Sen Gupta (1973). In this paper we present a brief sketch of the history and status of various gold and silver methods. A more detailed summary of atomic absorption spectroscopy (AAS) is Given, as this method has gained in popularity more than other assay methods. AAS methods currently in use are summarized and discussed briefly. This paper is not meant to be a detailed review, as are the above mentioned publications. Rather, we borrow from those works and more recent papers to report trends in gold and silver analyses (particularly in AAS). Also, we discuss some selected poten¬tial problems, and problems that have been experienced by this laboratory.

Jan 1, 1981

By Wallace W. Wilson

It scarcely 1s possible to read a new issue of any of the principal mining trade journals without noting some mention of a major new overseas mining venture with which one or more domestic companies are involved. These projects seem to follow a fairly consistant pattern; most are large open pit mines, with relatively low grade ore bodies but huge reserves; the total price tag will be in nine significant figures and around half or more of the total cost will be for infrastructure. West1 noted that nearly $7 billion is being invested annually for new mining projects and the expansion of existing mining ventures, in the free world. He anticipates that by the year 1975 such investments would reach the $10-11 billion annual figure, and that in the five year period 1972-76 total capital requirements can be expected to aggregate around $45 billion. The proportion of this total investment which will be financed in some manner is difficult to estimate because of the variety of available financing arrangements. West estimated that around 75% of the total capital would come from internally generated funds, with the balance from external sources. Conceivably a substantially higher percentage could be attributable to external financing, especially it the trend of recent mineral development in Canada and Australia is any criterion, and of course, including local sales of equity as a part of the package.

Jan 1, 1973

By S. M. Khandrika

Most of the coal presently used by the utility industry is cleaned at preparation plants employing wet processes. While water is the mainstay of coal washing, it is one of the least desirable components in the final product causing a reduction of the heating value as well as handling difficulties. Currently available dewatering techniques are inefficient for dewatering very fine coal (minus 325 mesh). The US coal industry has expressed serious concern about utilizing advanced cleaning processes such as column flotation because an efficient and economical dewatering process is not available.

Jan 1, 1992

By Gy. Deák

The Romanian mining and especially the salt mining industry is going through a restructuring phase; among others it has to respect the European Environment Act. One of the most important deficits of the salt mining industry is the implementation of monitoring systems for geomechanics phenomena, in order to develop an important information database and form a real base for salt mines stability, prediction and prevention measures. Monitoring system solutions, involving discontinuous and continuous measurements of displacement / deformation fields, around underground excavations, are presented and discussed. In addition, a case study for the stability prediction of an experimental salt off-set, located in the Praid salt mine, using DKRControl method, is presented. The two monitoring systems use different tools, namely measuring tapes (to determine distance between markers in T-D station) and ultrasonic transducers (SM-TDA equipment).

Jan 1, 2006

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

Solvent extraction-electro- winning appears to be one of the most important processes for the future in the North American copper industry and for this reason both the SX and EW steps are furtive areas for development. This paper has the objective of reviewing the present state of the electrowinning technology. It discusses some recent equipment developments and concludes by discussing the direction the technology will likely go fn the next decade.

Jan 1, 1985