Search Documents

By M. Leduc, M. Backens, M. E. Smith

An emerging technology for sustainable development in mineral development, tailings co-disposal™ is a means to dispose of conventional mill tailings within the void space of a waste rock dump. This method, while not applicable to all tailings systems, can offer a significant reduction in short-term and long-term environmental liability, land disturbance, closure costs, and negative public image. The concept is to dispose of the tailings simultaneously with the waste rock or leach ore, controlling the ratio of tailings to coarse material such that the resulting dump is stable both physically and chemically. The resulting co-disposal dump can be as safe as a conventional waste dump. In the case of alkaline tailings in a potentially acidic waste dump, the acid production can be buffered or slowed.

Jan 1, 2004

By Y. C. Kim, M. Preston, F. Martino

Because of the high cost of obtaining coal washability samples, it has been difficult in the past to obtain washability variograms. As a result, it could not be determined if the geostatistical prediction tool known as kriging can be applied to predict in situ coal washability characteristics. This paper presents the obtained variogram models for the Upper Freeport coal seam in western Pennsylvania. Variogram model parameters are presented for a total of 27 models. They are for four different variables: float- weight, ash, sulfur, and Btu, at seven different specific gravities: 1.275, 1.300, 1.325, 1.400, 1.600, 1.800, and 1.80,Sink. Based on the obtained variogram results, it can be con¬cluded that all attributes of coal washability show definite spatial correlation structures, and, consequently, geostatistics can be used to predict the in situ coal washability characteristics.

Jan 1, 1990

By Michael J. Friedel

The permeability and flow capacity in unsaturated media is investigated by the Bureau of Mines for application to in situ copper leach mining at the Cyprus Casa Grande mine site. Moisture retention properties are derived and combined with scanning electron microprobe data to characterize the mineralogy, texture, pore size, distribution, and permeability of the host rock. Finite element modeling is used to derive a saturated permeability, ambient degree of saturation, and assess various injection-recovery schemes. Recommended design modifications for optimization of solution distribution and maximum recovery from the rock matrix requires either (1) the injection pressures on the order of 1500 psi and recovery wells operating in a suction mode, or (2) performing permeability enhancement, through rubblization. By producing a maximum block diameter of 4 m, injection pressures can be reduced to 500 psi with improved recovery and containment of solutions.

Jan 1, 1991

By Lyman File

This paper discusses the overall challenges to construct a two-lane highway tunnel located in southwestern Colorado on U.S. Highway 160 for the Colorado Department of Transportation by the Kiewit Western Company. The purpose of this project is to provide the excavation and temporary support for a highway tunnel 280 m (916 feet) long. The tunnel cross section is 14.3 m (47 feet) wide by 8.5 m (28 feet) high, 105 m2 (1,130 SF).Construction methods include conventional drill and blast excavation with rockbolt and shotcrete ground support. This unique tunnel is being constructed under alpine tunnelling conditions and in the immediate vicinity of active highway traffic.

Jan 1, 2003

By M. J. Hannan

Considerable interest has arisen in developing analytical methods suitable for measuring resource commodity substitution patterns. some of this work has applied the Translog method to estimate actual elasticities of substitution. Recent examples incl.uae Privolos and Dunietz (1987), Kopp and Smith (1983), and Moroney and Trapani (1983). Another method, one which has received attention earlier in the work of Fisher and Pry (1970), is that of the logistic or diffusion function. We believe that the latter method has properties suitable for analyzing current problems of material substitution. The present study thus evaluates this method in its original logistic form as well as an extended version incorporating additional explanatory influences. The analysis is applied to copper/aluminum substitution and iron ore beneficiation. Substitution for copper by aluminum is examined in the building wire and cable, and magnet wire end-use markets. For iron ore, the substitution of pellets for sinter is considered for the U. S. market.

Jan 1, 1990

By Muhammad I. Kabir

A new minitest of in situ uranium leaching processes at reservoir conditions is proposed. The test which consists of a single observation/ production well and two observation wells is designed to permit the evaluation of both restoration and leaching parameters. It is shown that by using a straight forward history matching procedure, sometimes called a type curve analysis, both the rate of leaching and the ultimate uranium recovery can be evaluated based on the results of the test. Type curves are presented for the case in which the reaction rate is kinetically controlled and there are no other minerals competing for oxidant. Other situations can be approached using the same techniques as those presented here.

Jan 1, 1981

By M. Karmis

Subsidence planning and control must be an integral part of mine design in order to minimize the economic impact of underground mining on the surface. Pre-calculation of surface deformations which may cause damage to surface structures must be performed and dam-age criteria must be established, if the response of structures to such movements is to be determined and the extent of damages to be assessed. In this paper the Surface Deformation Prediction System (S.D.P.S.), which can be used to predict accurately the vertical and horizontal parameters of surface movements due to underground mining, is discussed. The Subsidence Response Modeling Program (S.R.M.P.). which can be applied to evaluate the response of buildings to subsidence-induced movements, is also reviewed. Finally, an example is presented demonstrating the applicability of these techniques for subsidence design and control.

Jan 1, 1990

By Onuralp Yücel, Kağan Benzeşik, Ömür Can Odabaş, Selçuk Kan

Extraction and processing constitute an important area in the metallurgy of molybdenum. Molybdenum trioxide (MoO3) production is one of the most important stages in molybdenum production. In this study, the effects of different furnace types on MoO3 production were investigated by using molybdenum concentrate as a raw material obtained during the enrichment of copper ores. Preliminary experiments have been made using a chamber type furnace, and a transition to a pilot-scale has been carried out with rotary kiln experiments. The effects of a different time and atmospheric conditions on MoO3 roasting kinetics were investigated by experimental studies conducted in the temperature range of 500–650°C. It was determined that the optimum temperature and time for sulfur (S) removal was 625°C and 180 min in the studies carried out in the rotary kiln, and it was determined that 0.61%S content was reached with an average removal efficiency of 98%. The activation energy in these sets was calculated as 89.519 kJ/mol.

May 3, 2021

By C. A. Rowland

When studying the feasibility of using autogenous or semi-autogenous grinding, operating and engineering companies frequently request assistance from the mill manufacturers in three areas - 1. Recommendations for studying the suitability of autogenous or semi-autogenous grinding for the specific ore. 2. Mill sizing, to accomplish required grind. 3. Recommendations on mill design and operation. Rod mills and ball mills are selected by the use of bench scale standard grindability tests and established calculation procedures, of which the most frequently used are the Bond Grindability tests and the Bond Work Index equation(1). The accuracy of these have been reviewed by C. A. Rowland in his papers, showing the correlation of work indices calculated from plant operating data and laboratory grindability tests(2)(3). The selection of autogenous and semi-autogenous primary mills has not reached the stage where mill size selection can be made from bench scale tests. Considerably more extensive testing will be necessary than required for selecting rod mills and ball mills.

Jan 1, 1974

By Lauren W. Choate

Wollastonite, a calcium metasilicate, derives its name from the man who discovered the mineral, Doctor William H. Wollaston, an English scientist. OCCURENCE Occurences of the mineral have been noted in Finland, Switzerland, Russia, Japan, Mexico and in the United States in Texas, California, Arizona, and New York. The only commercial deposit now being exploited is at Willsboro, New York. It is mined and processed by the Cabot Corporation whose home offices are in Boston, Massachusetts.

Jan 1, 1964

By Martial P. Corriveau

The preparation of coal is essentially the same for export as it is for the domestic market. The big difference, I would say, is that, while coal for certain domestic uses (utilities, for instance) need not always be of the highest quality, as long as it is uniform, the buyer of coal for export invariably demands a well-prepared, top-quality product. And he is willing to pay for it, as long as he knows what he is buying. This is where quality control enters the picture. The day is long past since the export market was the dumping ground for coals which could not be sold on the domestic market. Today, the export buyer wants American coals not so much for a price but for the necessity of blending the American coals with foreign coals to achieve the desired chemical and/or physical characteristics, To blend intelligently, he must know in detail what are the qualities of the coals to be blended. Sampling and chemical analysis facilities at the piers provide the information on the coals exported, These facilities are maintained for the export buyer by independent laboratories; however, in one instance, the buyer operates his own laboratory. With very few exceptions, and Clinchfield?s Moss No. 3 mid-volatile coal is one, cargoes shipped overseas are loaded as blends of two or more coals. Up to now, foreign requirements have not been too clearly defined; therefore, shippers must be prepared to blend mixtures of the desired combination. Successful blending requires an accurate knowledge of the coals shipped. And this makes it necessary for the coal producer to maintain his own control laboratory.

Jan 1, 1959

By Andrew N. Peterson

US mine operators frequently fail to investigate more cost effective and productive bulk material handling systems because surface mines seem to lend themselves to truck ore haulage. In this country, as a result, use of conveyors to move heavy loads from mine to process facilities has been minimized, if not actually neglected. In contrast, there are more than 50 conveyorized surface mines in successful operation around the world. These mine operators have learned that properly applied conveyorized systems can offer major savings in capital and operating costs, which contribute to improved profits when combined with other proven mining technologies. Growing acceptance and application of conveyorized bulk material handling in surface mines also points up how unique each mine is and how careful planning contributes to maximum mine effectiveness. Because of these differences, mining executives and technical and operating staffs need to develop an understanding of three factors in applying conveyorized bulk material handling in surface mines: • Why each mine will benefit from the type of automation permitted by conveyorized operation, •What kind of equipment is available, and • What applications most effectively demonstrate the first two factors in action - hauling either ore or waste. The conveyorized systems considered in this presentation have production rates from 0.5-2.7 kt/h (500-3,000 stph). Worldwide, these systems have been operating since the early 1960s. Advantages of Conveyors Why do you want conveyorized bulk material handling? First, it almost always provides lower operating and maintenance costs. Second, it frequently requires lower initial capital costs and almost always requires lower capital costs over the life of the surface mine. Third, it provides comparable operating availability, and finally, it frequently gives comparable operating flexibility - depending on the mine plan. Cost avoidance can be accomplished with modern production methods. These, in turn, permit increased productivity and reduced operating costs such as those for energy, maintenance, and manpower. It has been demonstrated in European surface mines and elsewhere, that conveyor systems frequently require lower initial costs than does truck haulage. Almost always such operations require lower capital costs over the mine life. Those costs include the continual addition of haulage trucks to both accommodate the increasingly difficult haulage routes and fulfill replacement requirements when trucks wear out. Conveyor systems handling ore in numerous large crushing and port facilities, which have operated since the early 1950s, have clearly demonstrated a useful conveyor life of more than 25 years. In contrast, off-highway trucks have life spans of six to eight years. The following examples illustrate comparative capital costs to purchase conveyor systems and comparable truck haulage units. Example 1 The ore haulage route from point A to point B is level and 610m (2,000 ft) long. The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be transported at a rate of 1.8 kt/h (2,000 stph). The installed capital costs to provide a properly designed conveyor that will transport the described material from point A to B is about $450,000. The capital cost to purchase three 77-t (85-st) off-highway trucks and one spare truck - which would provide equivalent capacity - would be about $1.2 million. The truck cost estimate is based on a 6 min. or 771 kt/h (850 stph) truck cycle time. Truck efficiency is estimated at 0.8. Each 77-t (85-st) truck would have an actual haulage rate of 617 kt/h (680 stph). Therefore, three trucks would be necessary to transport the designated tonnage of 1.8 kt/h (2,000 stph). A movable crushing plant would be located at point A for the conveyors and a permanent crushing plant at point B for the truck haulage system. Capital costs for these primary crushing plants were not included in the calculations for either system because the capital costs are frequently comparable. Example 2 The transport route from point A to point B is 610 m (2,000 ft) horizontally and 122 m (400 ft) vertically - on a 20% grade (Fig. 1). The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be moved at a rate of 1.8 kt/h (2,000 stph).

Jan 6, 1983

By David Runnels

In September 1970, the Quebec Cartier Mining Company, started development of the Mount; Fright iron ore mine. The estimated ore reserve is in excess of 1,000,000,000 long tons with an average grade of 31.5% Fe. The run of mine ore is crushed, ground and concentrated to a product having 66% Fe and 5% silica at an annual concentrate production rate of 18.4 million long tons. The daily production rate of over 50,000 long tons of concentrate necessitates a daily mine output of approximately 250,000 long tons of material of which 50% is waste. The mine is located in the Province of Quebec, close to the Labrador border approximately 600 miles north-east of Montreal. The development of the mine necessitated the construction of an all electric one thousand housing unit townsite along with associated services such as a shopping center, swimming pool, arena, school, etc... A one-hundred mile long, 315 K.V. Dower line was built between the mine site and the Hydro-Quebec 735 K.V. existing power line between Churchill Falls and the Montreal area. The construction near the mine of a beneficiation plant was necessary to upgrade the 31.5% iron ore to a marketable product of 66% iron.

Jan 1, 1977

By P. R. Taylor

The ability to process complex precious metal sulfide concentrates containing antimony and arsenic, in an economic and environmentally safe manner, is an important problem facing the mining industry in the united states. Preliminary experiments have been performed to evaluate the possibility of treating a complex sulfide concentrate to recover antimony and precious metals while fixing the arsenic and sulfur as calcium arsenate and calcium sulfate. The process involves the oxidation of the antimony and arsenic minerals in the presence of soda ash (to collect the sulfur dioxide and to keep the antimony and arsenic from forming volatile compounds), the selective leaching of the arsenic from the roast calcine with a heated caustic solution, the precipitation of the arsenic and sulfate with calcium hydroxide and/or calcium chloride, the reduction of the residual antimony (collecting the precious metals), fuming of the metal to form a marketable antimony oxide, and crucible reduction of the residue to obtain a gold and silver dore. Experiments have been performed to evaluate the first stage of this process. Batch experiments were performed using synthetic concentrates of stibnite and arsenopyrite. Variables that were studied included: mixture weight fractions, temperature, gas flow rate, oxygen partial pressure and time. All of the off gas dust and sulfur containing gases were collected and analyzed. The roast solid residue was subjected to arsenic leach tests and the leach solutions were subjected to arsenic and sulfate precipitation tests.

Jan 1, 1993

By G. Kritikakis

Rehabilitation of sites contaminated by oil products and chlorinated organic compounds is a costly task which affects the planning of urban and infrastructure development. An integrated approach based on the non-invasive geophysical technology is utilized for subsurface characterization of contaminated land. In this approach the localized information, provided by chemical analysis of soil samples collected from bore-holes, is used for the calibration of the geophysical data. This information is subsequently extrapolated to the area under investigation by combining it with the geophysical results, providing thus information about pollution accumulation, contaminants? flow and pollution sources. Two case studies are presented from sites contaminated by heavy metals (Venice, Italy) and oil products (Athens, Greece). Resistivity, electromagnetic and seismic methods were used in this approach. Namely, electrical tomography, electromagnetic mapping, ground penetrating radar (GPR), multichannel analysis of surface waves (MASW) and seismic refraction experiments were conducted. In Italy, the sections from the multichannel analysis of surface waves imaged successfully a buried channel where the pollution is concentrated. Preliminary results are also discussed from the geophysical survey in Greece where the thickness of the oil phase located on top of the water layer is 60 cm.

Jan 1, 2006

By Adabala Raja Venkata Sai Naresh, Radhakanta Koner

Particle size distribution (PSD) is an essential parameter in assessing the overall efficiency of blasting operations in mines and the subsequent mine-to-mill process in the mining industry. Despite some drawbacks of 2D image analysis techniques in accurately estimating particle sizes in PSD, the mining industry has relied on them for the last three decades. This study proposes the 3D rock fragmentation measurement (3DFM) technique for deducting the accurate dimensions of 3D rock particles for the PSD. 3DFM has utilized different processing algorithms. Images of different views of the non-touching rock particles of varying sizes have been acquired as a data acquisition step of structure from motion technology for generating sparse point cloud. Dense point cloud reconstruction is used to avail finer details of the point cloud using clustering views for the multi-view stereo algorithm. Random sample consensus (RANSAC) algorithm coupled with an unsupervised classification using the density-based spatial clustering of applications with noise (DBSCAN) classifier is employed to extract the rock clusters from the 3D point cloud. Finally, the accurate rock sizes are derived using the hybrid bounding box rotation identification (HYBBRID) algorithm with a root mean square error (RMSE) of 0.10 cm for length, 0.10 cm for breadth, and 0.32 cm for depth. The PSD of rock fragments obtained from the proposed 3DFM technique is found to be matching with the results of mechanical sieving and manual gauging with an R2 values of 0.98 and 0.99, respectively. The 3DFM method can be considered cheaper, more accurate, and computationally faster in determining the rock dimensions for the PSD determination method to enhance the productivity of the mining industry.

Dec 29, 2023

By David B. Campbell

INTRODUCTION This submission was made to the Royal Commission of Inquiry into uranium mining in British Columbia. It discusses the stability of waste rock piles that might be developed in conjunction with uranium mining and the control of leachates that might be generated within these waste rock piles over the short and the long term. Short term refers to the interval during which a waste rock pile undergoes either continuous, or alternatively intermittent development, and in general can be considered to extend over the operating life of the mine. Long term refers to the postmining period, i.e. after the ore-body has been exhausted, and mining operations have ceased. Two major classes of waste material are generated in the course of mining and milling operations. Tails, which are the solid waste materials produced by the milling operations commonly exit the mill in slurry form and are stored in tailing retention ponds. Management and control of these slurried wastes are the subject of other papers to the Commission and this conference. In the course of the mining operations, it may be necessary to remove rock materials that are below cut-off grade. That is, ore concentrations within some of the mined rock may be lower than the concentrations which on the basis of economic considerations justifies milling the material. Rock which is removed in the course of the mining operations, but which is below cut-off grade is referred to as waste rock. This waste rock is commonly consigned to a specific area for disposal where it is placed in a mound or pile, i.e. a waste rock pile. Ore concentrations within the waste rock may vary from zero to just below cut-off grade. Since an increase in the market value of uranium could at some time in future result in reduction of the cut-off grade, it follows that waste rock containing ore concentrations slightly below today's cut-off grade could become ore grade rock at some time in future. For this reason, the mine operators may deem it advisable to separate waste rock according to grade, and to consign the waste rock to two or more individual waste rock piles. For purposes of clarity and simplicity, this submission treats the stability of waste rock piles and leachate control in a manner which assumes that these potential problems are isolated and separate from other aspects of the mining and milling operations. For many site specific cases, the problem of potential leachate control might be integrated with the tailings management aspect of the project, thereby realizing economic benefits while at the same time reducing the potential for adverse environmental impact.

Jan 1, 1980

By G. J. Simandl

Jade is a commercial term encompassing green, white, black or yellow-brown jadeitite and nephrite. Jadeitite consists of Na-rich pyroxene, whereas nephrite consists of prismatic to acicular amphiboles of the tremolite-actinolite series forming bundles that are randomly oriented and interlocked. Nephrite is tougher (harder to break) than jadeitite. Its fracture strength is about 200 MN/m2 whereas that of jadeitite is about 100 MN/m2. On the other hand, jadeitite has a higher hardness (7 compared to 6.5 on the Mohs scale). There are over fifty known nephrite occurrences in British Columbia (B.C.). These occurrences consist of individual blocks, boulder fields, talus blocks and in situ occurrences. Most of the in situ occurrences are lens or cigar shaped. They occur at, or near the contact of ultramafic/mafic rocks (mainly serpentinites) with cherts, and other metasedimentary or igneous felsic rocks of Mississippian to Jurassic oceanic terranes such as Cache Creek and Slide Mountain. These contacts are commonly interpreted as shear/fault related. In general, it is believed that the B.C. nephrite formed by metasomatic exchange between ultramafic and silica-bearing rocks. Impurities in B.C. nephrite are spinel group minerals (chromite, magnetite, picolite), diopside, uvarovite, titanite, chlorite, and talc. Jadeitite is slightly denser than nephrite and good quality material sinks in methyl iodine. There are no known jadeitite occurrences of economic interest in B.C., but there are at least four geographic areas where favorable lithologies, and metamorphic conditions (Pn) required for the formation of jadeitite coincide. These are Bridge River, Pinchi Lake, Dease Lake, and Jennings River. These areas are known to contain small concentrations of jadeite, or are characterized by blueschist or eclogite-grade metamorphic conditions. Rhodonite and pyroxmangite are MnSi03 polymorphs. These minerals are pyroxenoids and are macroscopically and microscopically very similar. For brevity, both are grouped together under the term "rhodonite". Most of the B.C. occurrences are hosted by late Paleozoic chert sequences and are lens shaped and concordant. The common association of rhodonite with iron formations, jasperoids, and/or volcanogenic sulphide deposits in southwestern B.C. permits the delineation of favorable horizons using magnetic or electro-magnetic geophysical methods. Geographic associations between manganese showings and sulphide deposits, and the hydrothermal chemical signature of the rhodonite occurrences from this area, suggest a genetic link between rhodonite and volcanogenic sulphide deposits. The typical rhodonite rocks consist of rhodonite, pyroxmangite, neotocite, black amorphous Mn-oxides, Mn-bearing garnet, ± epidote, ±chlorite, ±rhodochrosite, ± parakutnah-orite, ± Mn-bearing calcite, ± iron oxides and hydroxides. Garnet ± epidote forms yellow patches and layers within the rhodonite. Within some of the rhodonite occurrences, the garnet is altered to chlorite. Rhodonite-bearing rock is commonly cross cut by secondary manganese oxide veins, creating a characteristic web-like texture. In several localities, the contorted bedding planes are readily recognized. Mn-calcite and quartz also crosscut rhodonite. Rhodonite deposits hosted by high grade metamorphic rocks may contain pyroxmangite. Rhodonite is an important gemstone and ornamental stone in B.C., second only to nephrite in dollar value. B.C. nephrite and rhodonite have been used for the past 100 years in local jewelry and ornamental applications. More recently they have been used in table tops, and they have potential as upscale materials in tile-making. There may be a market for tiles made from lower grade materials that were previously extracted and stockpiled. The prices of nephrite, jadeitite, and rhodonite vary widely with quality, but gem and ornamental grade stones are relatively highly priced materials and they trade world-wide.

Jan 1, 2001

By Zoltan F. Oszter

The frictional resistance to motion of a belt conveyor has always been a subject of intensive studies and research by engineers throughout the years. Numerous informations have been developed by analysing series of field tests on belt conveyors of different characteristics and carrying different materials at various capacities. Within certain limits of weight per unit length and tension, the theoretical considerations and the analysis of the field tests, both in the US and abroad, resulted in the development of similar formulas. In general these formulas are safe to use up to the following limits:

Jan 1, 1977

By Malcolm Wills

Boddington Gold Mine commenced operation in 1987 with an initial production of 3.0 Mt/y at a grade of 3.5 git. Head grade has reduced over the life of the mine and the major response to the drop in grade has been to increase mining rates and increase plant throughput. A capital expansion was carried out in 1996 increasing the throughput to 6.0 Mt/y and since that date tonnage has been increased without major capital expenditure. BGM's current mill throughput is 8.77 Mt/y ( 1999). In 1999 the combined basement plant and direct leach plant processed 8,770,055 tonnes to produce 233,507 ozs or 7.262882 tonnes of gold at an average head grade of 0.83 git. With grades of 0.83 git, and gold price at record lows, $US251.95loz in August 1999 or $A393.67loz it has been necessary to make and maintain major cost savings to remain profitable. Boddington Gold Mine has achieved this by a number of steps including a productivity study by outside consultants.

Jan 1, 2000