Search Documents

By Fathi Habashi

CRYSTALLIZATION from aqueous solution is a simple and old method for the recovery of metal values from leach solution. Practically all the methods for the recovery of aluminum from clay are based on the crystallization of an aluminum salt from the leach solution. Differences in solubilities may be used to advantage for separating two metals from the same leach solution. The classical method of Marignac (1866), which makes use of the difference in solubilities of K2TaF7 and K2NbOF5 to separate niobium from tantalum, has been used successfully in the manufacture of these metals (Fig. 10-1). The slurry containing the metal oxides is dissolved in 70 % hydrofluoric acid, diluted, and heated near boiling. A potassium salt is added in sufficient quantity to form the complex fluorides of the niobium and tantalum present. The solution is filtered and allowed to cool. At room temperature most of the tantalum salt crystallizes out while the niobium remains in solution.

Jan 1, 1970

By Richard D. Harvey

Petrographic properties of carbonate rocks are useful guides to the utilization of these rocks in SO2-scrubbing systems. High porosity and fineness of grain are thought to be the principal properties that contribute to high dissolution rates of the rocks in the scrubbing liquor. Lake marls and chalks are the major types of carbonate rocks that have these properties. Lake marls are composed mainly of equant grains of calcite (mean grain size generally less than 4 microns) weakly agglomerated in- to larger, porous particles. The marls commonly consist of 80 to 90 percent CaCo3 as calcite and aragonite. Impurities are, for the most part, quartz silt and organic matter. The average pore volume for samples of lake marls (1- to 1.2-mm particles) is about 0.50 cc/g, which corresponds to a porosity of about 57 percent. The mean size of pores in these marls is generally between 1 and 2 microns in diameter. Surface areas of lake marls range from 0.8 to 6.8 m2/g. Chalks have grain sizes and shapes similar to those of lake marls, but they generally have smaller amounts of quartz and organic matter and minor amounts of clay minerals. Pore volumes differ from one chalk formation to another; the 1- to 1. 2-mm particles average about 0.20 cc/g, which corresponds to a porosity of about 35 percent. The mean diameter of pores in chalks tested ranges from 0. 15 to 0.76 micron. Surface areas of chalks range from 3. 2 to 20. 1 m2/g. In the United States lake marls are restricted largely to Pleistocene- age sediments that occur in the states around the Great Lakes. Chalk and chalky limestones are restricted mainly to the Upper Cretaceous and Tertiary strata in the Kansas-Nebraska-Colorado area and in the south- eastern states, from Texas to Florida. Results of laboratory tests of the relative dissolution rates of samples at pH 6 and 44°C indicate that, in addition to many lake marls and chalks, oolitic aragonite, pelecypod shells, and carbonate waste sludges from certain industrial plants also have high dissolution rates.

Jan 1, 1974

By E. Martinez

A heavy mineral sand sample was tested containing 13% heavy mineral consisting of rutile, zircon, and ilmenite. Eleven tests were run at a mill site with a Mineral Deposit Limited MG 4 spiral to determine the effect of the addition 0; magnets to the spiral compared to conventional gravity separation. Different magnet configurations and field strengths were tested. Optimum results were obtained with the spiral retrofitted with magnets. The heavy mineral content of the concentrate was increased from 55.5% in the control to 64.2% with the magnets. The 8.7% improvement in heavy mineral recovery was due not only to the weakly-magnetic ilmenite, but also to increased recoveries if the non-magnetic zircon and rutile. The increased recoveries were achieved with no loss of concentrate grade.

Jan 1, 1992

By J. M. Hans, M. F. O’Connell, G. E. Eadie

INTRODUCTION The U.S. Environmental Protection Agency (EPA) was required, under Section 114(c) of Public Law 95-604, to provide a report to Congress identifying the location, and potential health, safety and environmental hazards of uranium mine wastes together with recommendations, if any, for a program to eliminate the hazards. The approach taken to prepare the report was to develop model active and inactive mines and locate them in a typical mining area to estimate their environmental impact. A list of uranium mines was acquired from the U.S. Department of Energy (DOE). The inactive mines were separated from the list and sorted into surface and underground categories. A literature search was conducted to obtain and consolidate available information concerning the environmental aspects of uranium mining and shortterm field surveys and studies were conducted to augment this information base. Radioactivity emission rates were measured or estimated for each mining category and were entered into computor codes to assess population exposures and subsequent health risks. The general environmental condition of inactive uranium mines was determined by walk-through surveys in several mining areas. INACTIVE SURFACE MINES We assumed that a model inactive surface mine contains a single pit with the wastes (overburden and sub-ore) stacked into a pile adjacent to the pit area. No credit for reclamation is given to the model mine. In lieu of the availability of individual mine production statistics, the model surface mine size was established from the total ore and waste production statistics for all surface mines, divided by the number of inactive surface mines. The number of inactive mines, obtained from the DOE mine listing, are summarized by type and location (Table 1). For modeling, we assumed that there are 1,250 inactive surface mines. The total or cumulative waste and ore production for inactive surface mines from 1950 to 1978 is not fully documented. Uranium mine waste and ore production statistics, on an annual basis, were available for both surface and underground producers from 1959 to 1976 (D0159-76). Annual uranium ore production for each uranium mining type are available for 1948 to 1959 (DOE79) and for combined ore production TABLE 1. Consolidated list of inactive uranium producers by State and type of mining [State Surface Underground AL 0 9 AZ 135 189 CA 13 10 CO 263 902 ID 2 4 MT 9 9 NV 9 12 NJ 0 1 NM 34 142 ND 13 0 OK 3 0 OR 2 1 SD 111 30 TX 38 0 UT 378 698 WA 13 0 WY 223 32 Total 1246 201T] for underground and surface mining from 1932 to 1942 (DO132-42). In order to estimate waste accumulated prior to 1959, the waste-to-ore ratios from the 1959 to 1976 period were plotted vs. time and line-fitted by regression analysis (Figure 1). Unfortunately, the extrapolation of the line to years prior 1959 approached zero in 1954 although surface mining began in 1950. Therefore, a waste-to-ore ratio of 8:1 was used for the period of 1950 to 1959 based on ratios estimated by Clark (C174). The waste to-ore ratios for 1976 to 1978 were estimated using the line established in Figure 1. By using waste-to-ore ratios and ore production data, the cumulative waste and ore production for both surface and underground uranium mining is estimated to 1978 (Table 2). The estimated cumulative waste from uranium surface mining for 1950 to 1978 is 1.73 x 109 MT. A crude estimate of the waste accumulated at the model inactive surface mine can be made by dividing the total waste produced to 1978 by the number of inactive mines. This, however, overestimates the waste tonnage because some of the contemporary wastes are being produced by active mines, and the waste accumulated at newer mines has increased in recent years. To adjust for this overestimate, we assumed that all mines operating in 1970 will be inactive by 1978. This eight year period is approximately one-half the lifetime of a model

Jan 1, 1981

By Douglas A. Sloan

Who would believe that young elementary school children could understand something as complex as the mining industry? THE CHALLENGE The challenge of accomplishing this is tremendous. An examination of Canadian school children indicated that they knew very little about the world of work in general, and hardly anything about the mineral resource industry in particular. It calls to mind the story about two youngsters who decided to play house. The little girl played her role well as she went about the house doing things she had watched her mother do every day. When it was the little boy's turn, he grabbed his lunch, waved goodbye to his "wife", jumped on his bicycle and pedalled furiously down to the end of the driveway -- where he stopped. The youngster explained that he saw his dad go out of the driveway each morning, but he didn't know where he went, or what he did on the job. When you stop to consider the number of families today with two working parents, you can begin to appreciate the importance of the opportunities for role identity provided by this project.

Jan 1, 1979

By L. Adler

A fairly complex analysis is required to select, or evaluate a piece of excavating and bulk handling equipment and obtain its performance. At present there is little agreement as to what specific points should be considered, and even less on what procedure to follow. This paper provides both of these in a consistent and direct form. The analysis applies to all types and sizes of equipment from the bulldozer and the continuous miner, to the B.W.E. The importance of the equipment characteristics, job activities, and work conditions are stressed and separate analytical stems are established in a flow chart for these. They are combined using suitability tests in the following steps: 1) problem statement, 2) natural conditions, 3) suitability guidelines, 4) appropriate equipment types, 5) operational activities, 6) encumbered space, 7) geometric design, 8) equipment sizing, 9) failure and limits, 10) performance and consumption, 11) public policy checks, and 12) costs and profitability. Public policy and economics while considered throughout receive emphasis towards the end. The procedure is iterative, containing distinct feedback loops. Specifying the steps and sequence provides a necessary structure which has long been overdue.

Jan 1, 1983

By Dale W. Norris

United States Steel's Cumberland Coal Operations is located in Greene County in the southwest corner of Pennsylvania. The mine and related facilities have been in operation since September of 1977. Production from this mine, U. S. Steel's first commercial coal mining venture, will eventually reach a level of 2.72 million mt of clean coal per year and is totally committed to electric power generation. Cumberland is a slope mine in the Pittsburgh seam and is mined by continuous mining machines and longwall. The coal from the mine is trans- ported by belt to the surface, taken through a rotary breaker for initial preparation, and stored in raw coal silos. It is then processed through the preparation plant and taken to a clean coal silo where it is held for train loading. Cumberland Mine operates its am 28.16 km railroad to transport the coal to the Monongahela River. The unit train consists of thirty-one 90 mt cars. The coal, once loaded on barges, is then shipped to the customer. Cumberland Mine is one of the most modern coal preparation and unit train loading systems in the nation. The preparation plant is de- signed to receive coal from the silos at a rate of 720 at per hour. The +6.35 mm material is screened out and cleaned in a Daniels heavy media vessel with two 3.35 m weirs. Minus 6.35 mm material is fed to sixteen #88 Deister concentrating tables. The cleaned coal from this circuit is dewatered, and all effluents from the mechanical dewatering report to the classifying Cyclone sump for classification through ten 35.6 cm cyclones. The cyclones overflow material (-150 mesh) is processed through two banks of three 8.5 m3 Denver D.R. flotation machines. The cyclone underflow pro- duct (28-1 0 mesh) is processed in two banks of 5 six 2.83 m Denver Sub A machines. The clean flotation product is then dewatered in Bird screen bowl centrifuges, blended with the other clean coal size fractions, and the total plant product further dewatered in a thermal dryer.

Jan 1, 1980

By P. R. Busmann, D. J. Rogers

The Bureau of Reclamation's Syar Tunnel project included excavation of a 9.2 kilometer (5.7 mile) long, 3.6 meter (11.8 ft) diameter tunnel through gently dipping sedimentary rocks consisting of shales, siltstones, sandstones and limestone. The tunnel was supported full length with precast concrete invert segments and lightweight steel sets and lagging. Several world records for advance rate were set, including 57 meters (187 ft) in an eight hour shift and 127 meters (417 ft) in a 24 hour day. The tunneling system utilized a remanufactured and modified Robbins hardrock TBM and a 9,280 meter (30,450 ft) long, 61 centimeter (24 inch) wide, continuous conveyor system.

Jan 1, 1991

By G. B. Misra

Though installations of main mine fans vary widely, the commonest installation is of a surface exhaust fan connected to an upcast shaft some distance below its collar by a horizontal fan drift bending sharply. downwards near its junction with the shaft. The junction of the fan drift with the shaft often causes considerable shock pressure loss if not properly designed. In one of the major coal mines in India circulating 180 m3/s of air through the mine a pressure drop of 229 Pa out of the total fan pressure of 568 Pa occurred at this junction while in a smaller gold mine circulating 9.4 m3/s it was 147 Pa out of a fan-drift pressure of 382 Pa. With larger mines circulating larger volumes of air, ill designed fan drifts can lead to considerable wastage of the power of ventilation. Shock loss at the junction of fan drifts with exhaust shafts depends on (1) the angle of deflection of the bend, (2) sharpness of the corners (both inner and outer) at the junction, (3) the degree of contraction of the flow-stream which depends on the cross- sectional area ratio of the shaft and the fan drift as well as the amount of leakage through the shaft collar. It must be noted here that the friction pressure loss in the bend is negligible compared to the shock pressure loss.

Jan 1, 1980

By Daniel M. Flanagan

"Editor’s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals & Aggregates Division technical committee chair and vice chairs, and to the authors of the individual commodity profiles. Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Joe Garska, member SME, of Imerys, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• Hyunjung Kim, member SME, of Chonbuk National University, agricultural materials.• Xihui Lin, member SME, of Kemira, ceramics and refractory materials.• Nikhil Gupta, member SME, of Virginia Tech, chemical raw materials.• Adam Rodriquez, member SME, of Penn State, construction aggregates.• LeDeana Roberts, member SME, of Imerys, fillers and pigments.• Harsha Kolla, member SME, of ChemEOR, sorbents, filters and process aids.• Edgar Blanco, member SME, of FLSmidth, specialty minerals.Their help makes possible this July industrial minerals issue. On behalf of ME readers, the editors thank them.During the past 25 years, U.S. ball clay production (the quantity sold or used by domestic producers) increased from 788 kt (869,000 st) in 1990 to an alltime high of 1.31 Mt (1.44 million st) in 2003 (Fig. 1). Housing construction within the United States, a leading market for ball clay-based ceramics and sanitaryware, began to decline in 2005, which resulted in a considerable decrease in sales of ball clay that continued through the 2008-2009 economic recession. After bottoming out at 831 kt (916,000 st) in 2009, ball clay production steadily increased through 2015 (Fig. 1). Estimated sales in 2015 were 36 percent higher than those in 1990 and 18 percent lower than those in 2003.Four companies (H.C. Spinks Clay Co., Imerys S.A., Old Hickory Clay Co., and Unimin Corp.), mined ball clay in five states during 2015. An estimated 1.7 Mt (1.18 million st) of ball clay valued at an estimated $47.5 million was sold or used by U.S. producers, a 4-percent increase from 1.03 Mt (1.14 million st) valued at $45.2 million in 2014. Approximately 65 percent of total ball clay production was air-float, 25 percent was crude or shredded and 10 percent was water-slurried"

Jul 1, 2016

By A. Mehmet, W. A. M. te Riele

A pilot-plant investigation in a NIMCIX contactor has shown that activated carbon can extract more than 93% of the gold in return-dam solutions. The average gold concentration in the barren solution was less than 0.003 mg/L from a feed averaging 0.048 mg/L. The carbon was eluted by the Zadra procedure. The operating conditions of the elution-electrowinning circuit are reported, and the elution of the gold and other metals is discussed. The reactivation of the carbon by use of the Rintoul kiln is described, together with the results of reactivation. The consumption of reagents in the process cycle is presented in sufficient detail to allow the economic viability of this technique to he evaluated for the recovery of gold from low-grade solutions.

Jan 1, 1990

By John C. Bowling

Many recent mine developments in North America are located in remote northern regions with extreme winter temperatures in the range of -20oF to -60°F. In addition, many locations are subject to very heavy snowfall. This paper discusses some of the key considerations in the planning and design of mine plant buildings, particularly concentrators, located in these regions. SUMMARY & CONCLUSIONS The subject is considered under three main headings: I. Building Out line and Structural Frame 2. Wall and Roof Materials 3. Foundations The plan outline of a mine plant building will naturally be governed by the scope and layout of the process equipment it contains. The selection of roof profile, on the other hand, will generally depend upon a number of factors extraneous to the process e.g. snow conditions. When these factors are considered for concentrators in cold locations, a flat or stepped roof will usually be more economical and suitable than a sloping roof. The materials normally used for the structural framework of concentrators are the same as used for other industrial buildings, namely steel, concrete and wood. Structural steel, however, is the most commonly used material for concentrators in

Jan 1, 1971

By N. J. Themelis

Autogenous grinding, broadly defined as the self-comminution of ore in a cylindrical tumbling mill without using auxiliary grinding media, was first applied in the early thirties in the so-called Hadsel mills (Figure 1) mainly used in gold mines on the U.S. West Coast. A number of these mills were built in sizes of 20 to 24 ft. in diameter and five-six feet in length but were later abandoned because of operating and maintenance problems. Further development of autogenous grinding led to the Hardinge wet grinding mill (Figure 2), the Aerofall dry grinding mill and others. A tabulation of all known autogenous and semi-autogenous installations around the world was sent recently to the authors by Hr. G. J. Kushner of the Koppers Mineral Processing Division. In the size range of 24 to 32-ft. in diameter, it lists a total of thirty mills used in the processing of copper ores. An additional 120 units are listed in the same size range for the processing of iron ores and other minerals. The largest mills in existence are 36-ft. dia X 15-ft. long mills in Minnesota, powered by 12,000 hp. motors and used in taconite beneficiation. It is indicative of the phenomenal growth of this technology that none of the above one hundred and fifty mills was in operation prior to 1964.

Jan 1, 1978

Reaction kinetics for gold dissolution in acid thiourea solutions were investigated using formamidine disulfide as an oxidant. For the conditions studied it appears that a surface reaction limits the rate of gold dissolution. The rate was found to be first order with respect to thiourea concentration and half order with respect to the concentration of formamidine disulfide; the apparent activation energy for the reaction was 10.40 kcal/mol (43.40 kJ/mol); and the reaction rate was independent of pH for the pH range 1.0 to 3.0.

Jan 1, 1999

By Michael David Harmse, Wiehan Adriaan Pelser, Jean Herman van Laar, Cornelius Stephanus Lodewyk Schutte

The South African deep-level mining industry is characterised by high operating costs and narrowing profit margins. Compressed air is commonly the largest consumer of energy in these mines, and any inefficiencies reduce profitability. Various methods aiming to optimise the compressed air networks have been implemented without an ideal economic dispatch strategy due to the lack of compressed air storage. In this study, a genetic algorithm was developed to evaluate the financial benefit of converting underground haulage to act as an air receiver (compressed air storage). By converting inactive haulage of 1.17 km in length into a volumetric air receiver, an annual monetary benefit of R2.5 million ($163 200) can be achieved, with a payback period of fewer than eight months. However, implementing the ideal size air receiver would result in an annual monetary benefit of R7.67 million ($500 700).

Jul 11, 2022

By William J. Taylor

Strictly defined, a stull is an inclined or horizontal timber support; a vertically placed timber is defined as a prop. Common usage allows the catchall term "stull" to refer to all such uniaxial mine support, regardless of orientation. Typically a stull is a round wooden column that is wedged in place to provide short-term auxiliary support between sill and back, or between hanging wall and footwall. Stulls may be used exclusively or in con- junction with other support systems such as roof bolts, shotcrete, or cribbing. Stulls are used both as local temporary support in stoping operations and for uniform systematic support installations. Where stoping areas are to be abandoned soon after excavation, stulls may be used to provide temporary support during mining operations. Where controlled caving and subsidence is required, stull supports are designed to fail in a systematic, predictable manner. Wood type is selected on the basis of availability, price, and load carrying characteristics. Coniferous woods are typically used, especially to carry heavy ground loads. Brittle woods are generally avoided because of their tendency to fail suddenly. Gradual yielding failure is preferable to sudden, unexpected failure of the support. Some usage of wood from deciduous trees such as cottonwood and other poplars has been reported in Grants, NM. These stulls reportedly mushroomed as the ground load increased but continued to maintain their structural integrity. Stulls fabricated from structural steel are used in special applications. Adjustable lengths are commercially available in mechanical, hydraulic, and pneumatic designs. The high cost of mechanical stulls limits their use to mining systems where recovery and reuse is possible. End blocking, also called headboards or footboards, uses wood blocks that are placed between the stull end and the ground they are supporting. The blocks are typically 50.8 to 101.6 mm (2 to 4 in.) thick, 203.2 to 304.8 mm (8 to 12 in.) wide, and 381 to 609.6 mm (15 to 24 in.) long. End blocking serves to distribute the support over wider back area. Compression of the end blocking gives visual indication of wall movement prior to failure of the stull. A common application of the stull is in flat-bedded uranium mining during pillar extraction. Many western US uranium mines use a pillar pattern development to delineate the irregular ore pods. After development of an appropriate sized pillar, the ore pillars are then sequentially mined out, leaving the undercut hanging wall or back to cave. Where thickness of the ore is less than 4.3 m (14 ft), stulls are generally used to provide ground control as the pillar is removed in slices. Experience dictates the density of stull placement. In general, the number and size of stulls should be sufficient to resist ground closure and to provide support for drilling and loading operations adjacent to the pillar. Stulls next to the mining face are often lagged 0.9 to 1.2 m (3 or 4 ft) up from the floor (or sill) to confine the blasted ore to a passage next to the pillar. Mucking is simplified by this confinement. Experience dictates whether back control along a mining face requires removal of stulls to allow con- trolled subsidence of the back or hanging wall. Without caving or closure, abutment pressure can create poor ground conditions near the pillar.

Jan 1, 1982

By Jozef S. Stachulak

Inco Limited operates 11 underground mines in the Sudbury District. The mines are located on the rim of the Sudbury Basin, an oval with the axis in the range of 27 and 60 km. The ore dips to at least 3000 m below surface. The ores are mined primarily for nickel and copper. Total ore production from underground is in excess of 55,000 tons per day. Over 40 surface fans have been installed since the late 1960's. All of the fans are adjustable pitch, axial flow units. A major factor influencing ventilation design in the last 30 years has been the introduction of diesel equipment underground. Volumes per fan have ranged from 60 to 330 (cubic metres per second), with motors from 100 to 2500 hp. Fans of the axial flow type have been in common use for main fan installations at Canadian mines for many years. The standard arrangement has been to mount these fans horizontally, i.e. with the fan shaft and the long axis of the housing horizontal. This is a natural arrangement for an underground fan, but for a surface installation, a vertically mounted fan has definite advantages. The surface area taken up by a typical vertical fan installation is generally about one quarter of that with a horizontal fan of the same capacity. (1) This is not a problem with isolated fans and flat surface outcrop sites, but where the installation is to be near existing buildings, or where there are poor surface soil conditions, space and cost considerations greatly favour vertical fans. MAIN FANS INSTALLED There are 43 main surface fans in operation at 11 mines. Twenty-seven of these fans are supply units, and 75% of them are vertical installation. The remaining 16 units are main surface exhaust fans, with predominantly horizontal installation. Within the last five years, some 20 main booster fans have been installed underground at several mines. Axial flow fans, with adjustable pitch blades, are used for both surface and underground installations. Exhaust fans are equipped with stainless steel or cast aluminum blades. Main underground fans are arranged horizontally and the majority of them have a floating shaft between the fan shaft and the motor. (2) The size of the fans in service varies from 1.8 m to 5 m in diameter, with the majority ranging from 1.8 to 2.5 m. The pressure produced by these fans varies from 0.25 kPa to 2.0 kPa. At Inco Limited, two main fans in parallel are preferred, rather than a single fan, so that if one fan fails, the remaining fan can still supply up to 70% of normal air quantities, while the damaged fan is repaired. This requires closure doors on each of the fans so the fan can be isolated in case of failure. It is more expensive than a single fan, but results in less production interruptions. The fan installations are well away from sharp inlet and outlet bends. FAN DESIGN INTEGRITY Both the mine operator and the fan manufacturer must understand that the main fan is critical to the mine operation, and that everything technically possible must be done in design and manufacture to ensure the highest degree of reliability. Some of the design parameters and criteria, based on Inco experience, are outlined and discussed below. RESONANT FREQUENCIES AND HOUSING MODEL ANALYSIS Any fan assembly will have many different resonant frequencies. It is a challenge to the designer to arrive at a design in which forcing frequencies do not coincide with any of these resonant frequencies to produce unacceptable vibration levels in operation. Finite element analysis is a useful tool that can be used to identify the most critical of these, so that housing and blade stiffness can be adjusted to change any resonances that might be close to forcing frequencies. Shaft critical speeds should be at least 25% above the fan operating speed, and there should be sufficient separation between other resonant and forcing frequencies to avoid excitation that might result in high vibration levels. QUALITY ASSURANCE Radiographic Blade Examination Mine fan blades are normally cast in small lots. To ensure that the castings are sound, a full radiographic examination is recommended in the highly stressed lower 1/3 of the blade.

Jan 1, 1995

By J. D. Miller

X-ray computed tomography (CT) techniques have been developed for the medical services field in order to provide accurate internal images of the human body.(l-7) Now, a decade later, CT techniques are starting to be used in non-medical applications such as, non-destructive testing(8), flow pattern analysis(9), drill core examination (10,11), and coal characterization(12,13). In these fields of application, CT techniques offer the potential to extend our knowledge and understanding beyond that provided by more traditional methods of analysis. Although, CT systems involve very specialized and expensive equipment, the advantage of x-ray CT in revealing the detailed internal structure of an opaque material non-destructively should make it an important tool to provide a more complete analysis of mineral processing phenomena. X-ray CT systems generally consist of an x-ray source/collimation unit and a detector/data acquisition unit. The object to be examined is placed between the two functional units as shown in Figure 1. With this system the density array of selected cross sections of a chosen opaque object can be obtained in two dimensions. There are numerous areas in mineral processing to which x-ray CT technology can be applied and it is the aim of this article to identify these potential areas noting the advantages and limitations of the technology. Particular emphasis is placed on particle composition distribution and multiphase fluid flow measurements. In the case of particle composition distribution, liberation analysis and coal washability are considered. While in the case of multiphase fluid flow, swirl flow in the air-sparged hydrocyclone is given by way of example.

Jan 1, 1989

By G. Deschenes, P. J. H. Prud'homme

A laboratory study was carried out to evaluate the effect of oxygen and lead nitrate on the recovery of gold by cyanidation of a free milling gold ore, which contains 0.4 % copper as chalcopyrite. Efficient gold extraction is achieved only under specific conditions. The recovery of gold was increased from less than 90% to up to 98% by addition of lead nitrate. In the pre-leaching, the kinetics of oxidation of soluble sulphides are not an accurate indication for the length of the treatment. Even though the consumption of cyanide was reduced due to the inhibition of the dissolution of chalcopyrite by increasing additions of lead nitrate, cyanide consumption had to the held above 1.85 kg/t to maintain good recovery of gold. The continued addition of lead nitrate above 300 git had no impact on the recovery of gold. It was also found that the addition of lead nitrate at the start of cyanidation gave the same performance as when added during pre-leaching. The addition of oxygen increased the recovery of gold by 1.5%. The concentration ofNaCN had to be maintained in the range of700 mg/L because of the high concentration of copper in solution. The recovery of gold dropped significantly when the average NaCN concentration fell below 640 mg/L. Application of the findings of the laboratory study at the industrial scale led to improved plant performance.

Jan 1, 1997

Since 1955 Gaspe Mines has produced 144 million tonnes of ore, averaging 0.87% Cu, mined from two open pits and underground workings. In 1994, four exploration drill holes discovered a buried porphyry/skarn Cu-Mo deposit at depths of between 1000 m and 1700 m below the top of Porphyry Mountain. The mineralization and alteration associated with the Porphyry mountain quartz monzonite does not outcrop. A total of 19,500 m of drilling in 12 drill holes has outlined 200 million tonnes grading 0.73% Cu and 0.08% Mo. Mineralization occurs as veins and disseminations of chalcopyrite and molybdenite. Drilling and feasibility studies continue.

Jan 1, 1998