Search Documents

With mine activity dating back to 1792, the Lehigh Valley, about 80 km (50 miles) northeast of the historic Allentown/Bethlehem steel mills and about 160 km (100 miles) northeast of Philadelphia, PA, defined early-day coal mining. Coal mining began just nine years after the end of America?s Revolutionary War. The high-carbon, clean-burning anthracite coal that was hand-dug from the Pennsylvania hills fueled the steam engines that powered the Industrial Revolution, helping build early steam ships and even the first automobiles. Around 1910, at the peak of the U.S.?s early mining effort, there were more than 250,000 men working underground ? 10,000 of them in the Lehigh Valley.

Jan 1, 2012

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014

By Keith Kern, Joseph P. Matoney, Kenneth E. Harrison

INTRODUCTION "When there is an economic need for cleaning fine coal to low ash, the technical difficulties will be solved. The utilization of fines below 28 mesh will determine the degree to which beneficiation will be carried. Whenever these "fines" will be processed into smokeless fuels or used as new materials for the chemical industry or for hydrogenation, a higher degree of cleaning will be economically justified”.(l) This quote from the 1943 edition of Coal Preparation correctly anticipates the use of fines as "smokeless" fuel or as a future component of boiler fuel and a1 so as a raw material for the chemical industry or possible new uses such as for internal combustion engines. Fines utilization depends upon an economic need and possibly neglects to say an environmental need or a government funded development program as the prime mover for development. In any event, this conference is faced with the "need" to beneficiate fine coal and undoubtedly among the processes that will be discussed are the unit processes of future coal preparation facilities. HISTORY OF DEVELOPMENT It is interesting to look at where we have been, where we are now and where we possibly will be in the future. In order to put some limitations on this presentation, we will for the most part confine our remarks to this century and particularly developments since World War II. We also will limit our remarks to the preparation of bituminous coals in the United States, and for the most part, to wet processes. In the 1943 edition of Coal Preparation, clues to the processes being used to beneficiate coal are contained in the Chapter Titles. An extensive treatment of "Hand Picking" was contained in Chapter 8. Chapter 7 contained a description of methods for "Preparation at the Face". Chapter 18 dealt with "Slurries, Sludges, Slimes and Water Treatment" and defined this size of coal as being the size at which "Jigs and Chance Cones are usually dispensed with and other methods such as the hydrator, tables, and froth flotation are employed. Generally the limit is 1.7mm to 3.4mm. In the days before World War I1 the then modern bituminous coal preparation plant contained jigs or Chance Cones for the coarse material +6.35mm, concentrating tables, launders or some classifier type of coal washer for the fines (6.35 x 0.15mm), and froth flotation as the only method of cleaning minus 0.15mm coal which was used very sparingly.

Jan 1, 1988

By Robert L. Sundeen, Richard V. Wenberg

Overshot loaders are loading machines which fill a front-mounted bucket by crowding and bucket lifting, passing the loaded bucket over the machine and throw¬ing the load into a haulage unit to the rear. The load is retained in the bucket as the load mass is accelerated in its path over the machine. At the point of discharge, the bucket is stopped suddenly and the load leaves the bucket, following the throw trajectory past the rear of the loader. Fig. 1 shows a typical overshot loader of this type. Overshot loaders were developed for loading in nar¬row drift headings and drawpoints, where it is impossible to place or pass a haulage unit alongside the loader. Haulage access is to the rear of all overshot loaders. The first overshot loader was developed in the early 1930s. The early machines were rail-mounted, air¬powered, and had small loading capacities. To this day, the same basic design configuration exists, and all suc¬cessful overshot loaders still use compressed air. Bucket sizes range from 0.14 to 0.59 m3 (5 to 21 cu ft). The most commonly used machines are rail-mounted, al¬though crawler versions are popular for special applica¬tions, particularly shaft sinking. Rubber-tired machines have found some application where a greater travel distance is required between the loading and discharge points. CONDITIONS INFLUENCING APPLICATION Roadway Type Rail-mounted loaders are used where soft bottom requires rail support or where the long haul is ac¬complished with rail. This situation usually occurs in civil tunnels or in mine drifts that will continue to utilize rail-bound main haulage after development work is completed. Crawler and rubber-tire mounted loaders are used where the roadway surface is rough and lateral travel beyond the range of rail-bound machines is required. Work Area Dimensions The largest rail-bound loaders can clean roadways as wide as 4 m (13 ft) from a single track. Wider headings require multiple trackage. Headroom require¬ments are dependent upon the path described by the bucket as it passes over the machine. The largest over¬shot loader requires approximately 3.4 m (11 ft) of headroom. It follows that the largest heading that can be driven by overshot loaders from a single set of rails is approximately 4 m (13 ft) wide and a minimum of 3.5 m (11.5 ft) high above the rail. The smallest rail-bound loaders can work efficiently in headings as small as 1.8 m (6 ft) wide by 1.8 m (6 ft) high above the rail.

Jan 1, 1982

By Dean E. Albon

In the late 1940's and early 50's in southern Illinois, the usual open pit blasting in the coal field consisted of one or two rows of churn drilled vertical holes being shot with instant electric blasting caps. The entire shot detonated at one rime. In southern Indiana and Ohio most mines were drilling horizontal holes and they too were primed with instant EB caps. During the ten years from 1355 through 1965 many changes occurred in drilling and blasting methods. The churn drill in southern Illinois and the horizontal drill in Indiana and Ohio were replaced by the rotary vertical drill. The ammonia dynamites and liquid oxygen explosives were replaced by ANFO. The elctric blasting cap in the hole was replaced by a detonating cord down line and detonating cord trunk lines made the connections between holes and rows of holes. Host open pit mining was in areas far enough from town that the noise and vibration from blasting was, if not ignored, at least tolerated. During the 1960's open pit mining expanded to account for nearly 50% of the coal produced. Mines came closer to town and towns expanded along the highways with suburban homes and mobile homes. The mines began receiving complaints about the noise and vibrations from blasting operations.

Jan 1, 1976

By H. G. Naidu, Raj K. Singhai, S. P. Singh

Introduction The economics of open-pit mining de¬pend heavily on the cost of overburden removal. It is necessary to maintain a pit slope as steep as possible. Steeper slopes lower the volume of overburden to be handled, thus lower the cost of material handling. There is, however, a limit to which the pit slopes in any given situation can be steepened. Steepening beyond this point could jeopardize the pitwall stability, ren¬dering it unsafe. It might even result in curtailment of pit production. Several factors affect the stability of pitwalls. Some are natural, such as topogra¬phy and regional and local geology. Others are man made, such as pit geometry, ground water management, equipment, drilling and blasting, and the type of excavation. Greater control can be exercised in the latter with proper planning and by following a set of procedures based on field experiences. This article deals with one such control¬lable factor - drilling and blasting. The eco¬nomics of steeper pit slopes is discussed, followed by a record of drilling and blasting practices in western Canadian surface mines. Microprocessor-based instrumentation and its application to blasthole drilling is also described. Economics of steeper pit slopes The economics of steeper pit slopes is not a new issue. It should be reinforced, though, that pit slopes must be as steep as possible to ensure maximum recovery of minerals at a minimum stripping ratio. For operating, economic, and safety reasons, different pit slopes are maintained during different phases of pit development. Figure 1 shows a hypothetical ore body, cylindrical shape, with a radius of 225 m (740 ft) and located 30 m (100 ft) beneath the surface. The mining operations are planned at two different slope angles of 25° and 40°. The ultimate pit depth was established on the basis of the criterion of "break even pit." The variation of the stripping ratio at differ¬ent mine levels is shown in Fig. 2. Table I summarizes the eco¬nomics involved for two pit slopes, 25° and 40°. Figure 3 presents the profits during the life of the mine for these two pit slopes. This study shows that steeper slopes for an open pit operation are far more advanta¬geous than flatter slopes. But, what is the optimum slope at any one point in the life of a moving pit? And how can the stable slopes be maintained over the short- and long-term? Canadian blasting practices A survey of blasting practices in western Canadian surface coal mines revealed that, at most mines, hard consolidated overburden is drilled and blasted. Blastholes are drilled with rotary crawler-¬mounted rigs using bits in the 220 to 310 mm-diam (8.5 to 12 in.-diam) range. Typi¬cal hole depths are 12 to 18 m (40 to 60 ft) to accommodate the pit bench heights of 12 to 15 m (40 to 50 ft). For a 12-m (40-ft) high bench, a typical hole will be 14.6 m (48 ft) deep including the subgrade drilling of 2.6 m (8.5 ft). Half of this hole will typically be a powder column and half will be stemmed. For a 15-m (50-ft) bench, a typical hole will be up to 18 m (66 ft) deep including the subgrade drilling. Drilling patterns are usually 9 m (29.5 ft) spacing and 9 m (29.5 ft) burden. De¬pending on local geology and hole diameter selected, drilling patterns of 8 x 8 m, 8.5 x 7.3 m, and staggered patterns of 11 x 5.5 m

Jan 1, 1989

By Ernest B. Snyder

The word "line" has been used loosely for many forms of the common steel plant flux. For example, many people use the word "lime" for nigh calcium and dolomitic limestone, for high calcium and dolomitic quicklime (also called caustic lime, calcined lime; burnt lime, pulverized and pebble lime) and ;van for clinkered dolomite. Calcium hydroxide, also called slaked lime and hydrated lime, is called "lime" but is seldom used as a flux except when the quicklime air slakes in open boxes or bins. All of the above forms of "lime" are used in the steel plant. Calcium hydroxide is used for water treatment, acid neutralizing, and as a lubricant for wire drawing. All the other limes are used as fluxes in the sintering plant, blast furnace or steel producing furnaces. In the production of self-flux or super-flux sinter, high calcium and dolomitic limestone fines are used. Where quicklime fines are available, they may be added to the sinter mix also. The blast furnace uses both high calcium and/or dolomitic limestone. A few trials have been made using iron oxide stabilized dolomitic lime in an attempt to reduce coke consumption and to increase the production rate. The trials were very successful but would' not be economical, except in periods of coke shortages, with resulting extremely high coke cost and exceptionally high hot metal demand.

Jan 1, 1979

By Dan G. Wasyluk, Meryl J. Klassen, Tony J. Morris, Clive H. MacKay

The Rogers Pass Project in British Columbia has involved the construction of two railway tunnels totalling 16.6 km and a 345 m deep shaft. Systematic geological mapping was carried out at four headings during construction. The paper discusses the procedures used to record the geology, structure, rock mass characteristics and excavation performance. Coded data from the geological mapping and shift inspector reports was entered into a computer data base. The rock mass quality was evaluated for both the Geomechanics and Q classification systems. Continuous computer generated graphic logs were produced showing the excavated perimeter map, geological parameters, installed support and construction activities. The tunnel logs were updated on daily basis and used during construction by project staff for evaluating support requirements and monitoring excavation progress. The specific requirements, difficulties and advantages in mapping tunnels using a computer based system are compared to those of a conventionally mapped tunnel excavation with hand drafted tunnel logs.

Jan 1, 1987

By D. J. Turk

Faced with decreasing production from the gold heap leach operation, Robinson implemented a drilling and blasting program on the leach pads in 1993. This program offset some of the negative effects of low ore permeability and short circuiting of leach solution that resulted in lower than optimum recoveries. The drilling and blasting program created new solution flow paths and increased gold recovery. Production and pulp assays at depth intervals, prior to and following drilling and blasting, reveal the degree of short circuiting and benefits of the program.

Jan 1, 1995

By F. A. Molloy

As a result of feasibility studies made in 1975 a 3-0 seismic reflection survey was shot over part of the Veendam salt pillow during 1978-1979. The Zechstein salt pillow, located in the northeast of the Netherlands near the town of veendam, occurs at a depth of 1400 m and contains three carnallite rich horizons over an interval of 300 m below top salt. MgCl2 brines are produced from these layers as feedstock for a magnesia plant, which starts up in 1981. Prior to the acquisition of the seismic data four wells had been drilled. The thickness of the carnallitite layers encountered in these wells varied between 50 and 125 meters. In view of these variations it was necessary to obtain a reliable isopach of the different layers. The 3-0 seismic survey covered an area of ± 4x4 km with a sampling interval of 20 m in all directions. The data was recorded it an area array using a 120 channel instrument. Final presentation of the data was in the form of 3-0 migrated acoustic impedance cross sections. The quality and resolution of the seismic data allowed reliable structural and isopach mans to be made. It was shown that the carnallitite layers are continuous over the area surveyed, whilst local thickening is "fault" related. Having this information brine production locations could be choosen in the thicker parts, allowing maximisation of production potential whilst avoiding faults and fulfilling mining regulations. A subsequent benefit of this approach is the possibility of using the seismic data to predict ore grade. Using the available wells as calibration points the acoustic impedance response of the seismic at the well was matched to the ore grade found. From these points a synthetic section was made with varying ore grades. Pre¬liminary results are encouraging and the liability of this predictive tool will be evaluated in the light of future drilling.

Jan 1, 1981

By Robert Dimock

The successful management of large dispersed mineral operations is dependent upon accurate and timely decision making. The plant locations providing the data to support the decision making process are generally separated by distances which elongate the time required to accumulate the data at a central focus. The need exists to examine operational data in context with total mining operations, and in relation to target projections and historical trends. The use of microcomputers for local information tasks is an established capability. Grouping microcomputers into local-area networks is rapidly becoming established. Interconnecting multiple local-area networks to provide a free flowing stream of information between all operational locations of a mining enterprise is possible with use of some emerging technologies. The benefit of the potential interconnections and rapid transfer of information can readily be seen from a production reporting perspective. Numerous other advantages exist' by providing routing to enable a workgroup to be established between separated work functions.

Jan 1, 1989

By A. M. Tunstall

Blasting is commonly viewed separately from mechanical handling and crushing. This view is misleading because the degree of fragmentation achieved by blasting can have a significant effect on the efficiency of these processes and, hence, on the overall cost of the mining operation. In this paper, aspects of blasting and crushing and their interaction are examined. A case study is also presented that dramatically illustrates the influence of blast fragmentation on subsequent processing and on the financial implications involved

Jan 1, 1997

By J. P. Golightly

The nickeliferous laterites of Soroako are described in their setting in the huge Cretaceous ultramafic complexes of central Sulawesi, Indonesia. The ore bodies occur on spurs, ridges and hill flanks beneath remnants of extensive erosional surfaces. Weathering pro- files that have developed on unserpentinized harzburgite and on strongly serpentinized lherzolites show distinctive laterite structures, mineralogy and chemistry. The former are unique to the Soroako area and permit an unusual degree of upgrading by rejection of unserpentinized peridotite boulders. A mass balance calculated for a selection of profiles indicates that in situ leaching of a column of peridotite 20-50 meters thick has taken place with only minor lateral migration of nickel in solution.

Jan 1, 1979

By J. H. White

It is hypothesized that the Hotelling valuation principle (HVP) can determine the value of developed gold reserves using simple methods and easily obtainable data. This paper reports the results of an empirical test of this hypothesis. The model for the HVP is given by [V R=Cp-0(1) or V - CP-0' R(2)] where p = current spot price of gold per oz, [c] = average extraction cost of gold per oz, V = current market value of the gold in the ground (dollars) and R = gold reserves (oz). Using publicly available data from North American gold companies, we obtained data for V, R, p and c, and we ran a simple linear regression using Eq. (1) as the definition of the dependent and explanatory variables. By examining the value of the coefficients of the resulting regression equation, we can draw conclusions as to whether or not the HVP can be confidently used as an estimator of the value of developed gold reserves.

Jan 1, 1997

By F. Nelson

RJB Mining is the largest coal producer in the UK. In January 1995 the Company acquired the Central North and Central South Regions of British Coal consisting of: ? 15 operating collieries -including capital equipment ? 2 care and maintenance mines ? 16 operating Opencast sites ? Interest in 26 prospective and 46 potential Opencast sites ? Approximately 417 million tonnes of proven and probable reserves and considerable mineral resource ? 9 million tonnes of coal stocks ? Long term contracts to supply approximately 90 million tonnes of coal to National Power and PowerGen to the period of 3 March 1998 ?Approximately 7,600 employees and 4,500 mining contractual labour. Up to the acquisition RJB Mining had the capacity to produce 14 million tonnes of saleable output with an approximate 1,500 strong workforce.

Jan 1, 1998

By A. W. Laughlin

Analytical costs are a major part of exploration programs in developing nations which may lack adequate laboratories. Laser-Induced Breakdown Spectroscopy (LIBS), a variant of atomic emission spectroscopy, can reduce exploration analytical costs and can provide the analytical results in <1 minute. CPI is now marketing battery-powered, backpack mounted analyzers, using LIBS to analyze for many elements of interest to the explorationist. LIBS is well suited to the analysis of elements in industrial minerals. Limits of detection in ppm for some of these are: Li-1, Be-2, Na-100, B-33, Sr-10, Ba-300, Cs-1, K-500, Fe-500, Mg-500, and Ti-500.

Jan 1, 1999

By Nikhil Dhawan, SHAILA MIR

The emerging problem of electronic waste has promoted the interest in exploring metal recovery from secondary sources under the umbrella of urban mining. This study presents the physical and chemical characterization of various components present in end-of-life laptops to help ascertain the sites of metallic values and develop sustainable and environment-friendly recycling. The recycling potential of a laptop is evaluated by sequential disassembly, separation, and characterization of components such as body (49.8 wt.%), printed circuit board (9.7 wt.%), hard disk drive (4.9 wt.%), and battery (12.4 wt.%). The printed circuit boards comprise metallic values, majorly copper (25 wt.%), tin (5.8 wt.%), and lead (3.1 wt.%). The precious metals (Au, Ag) with an economic advantage are abundantly present in electronic components such as integrated circuits, capacitors, resistors, and processors. Critical elements such as lithium, cobalt, and rare earth elements are detected in the discarded laptops' batteries and hard disk drives. The recycling potential representing the amount of material that can be recycled in various components, depending on the type, concentration, and purity, is determined in the range of 36–100%. On average, a unit laptop contains~ 386 g of Cu (14.45 wt. %), 49.73 g Co (1.86 wt. %), ~346 mg Ag, ~141.2 mg Au, ~650 mg of rare earth elements (Nd, Dy). This study presents a database for investigating integrated and economical recycling techniques from different components of a laptop, and an overall process flow is also proposed.

Jul 24, 2021

By Robert Rautenberg, Ted Budd

The paper will discuss the successful construction of the largest dollar value ($194.5 million, U.S.) TARP (Tunnel and Reservoir Plan) project built to date for the Metropolitan Water Reclamation District of Greater Chicago. The mining and lining of the 18.5km (11.54 miles) tunnels will be emphasized. The tunnels were driven utilizing three TBMs ranging in size from 9.85m (32.33 ft) to 3.70m (12.16 ft) in diameter. The operations surrounding the 11,546m (37,876 ft) long 9.85m (32.33 ft) diameter tunnel will be highlighted. A total system concept was utilized to attain mining rates up to 29.3m (96 ft) per shift and lining productions of 58.5m (192 ft) per day. The reliability of these systems was instrumental in the completion of the project more than a year ahead of schedule.

Jan 1, 1995

By R. N. Gow

Acidic treatment of enargite (Cu3AsS4) dissolves both arsenic and copper from the mineral and then attempts to separate them in the leach solution. The reactivity of enargite was examined in acidic solutions, over the pH range 1-7, to determine a potential range for co-dissolution.. Enargite mineral samples from Butte, MT and Quirivilca, Peru were used as working electrodes in a cyclic voltammetry corrosion cell setup, which were then cycled multiple times over -1000 to 1000 mV. Surface reactions and transitions were characterized using in-situ Raman spectroscopy, which were then compared to updated predominance diagrams for the copper-arsenic-sulfur system from a previous study done under alkaline conditions. The region of co-dissolution is limited to > 600 mV vs. SHE and pH < 1 under the proposed diagram.

Feb 23, 2014

By P. R. Taylor

Batch leaching experiments have been performed to study the kinetics of galena leaching in fluosilicic acid solutions with oxidants. Variables studied included: fluosilicic acid concentration, oxidant type, oxidant concentration, particle size and leaching temperature. It was found that hydrogen peroxide was the most effective oxidant, compared to the others studied, and the effect of the oxidant concentration on the leaching behavior of galena was very significant. Also, decreasing the particle size and increasing the leaching temperature increased the extraction rate. The initial, apparent activation energy was calculated to be 11.72 kJ/mole (2.8 kcal/mole) and suggested that galena leaching in fluosilicic acid solution, with hydrogen peroxide as an oxidant, may be controlled by fluid film mass transfer initially. The reaction appears to be retarded by the formation of elemental sulfur and the sulfur oxidation becomes a major resistance to the overall leaching reaction.

Jan 1, 1992