Search Documents

By R. C. Ford, W. L. Niccoli, J. B. Finley

All mining operations are superimposed on natural hydrologic systems. As a result, mining operations are influenced by natural hydrologic processes and require water management systems to successfully conduct mining activities. Managing water and mining-related solutions is a critical task at all stages of the mine life because of the time-dependent nature of natural and mining-related flows. Effective operation of the mining water management system requires a “systems” approach that integrates the time-dependent effects of all water and mine solution handling components. This paper discusses the concept and application of dynamic systems modeling to address the time dependent nature of mining water management systems.

Jan 1, 2002

By E. C. Robertson

D.G. Wilder I found the suggestion that the amount of displacement of a fault can be numerically related to the thickness of gouge or breccia to be both intuitively satisfying and intriguing. I have long agreed that there is some type of relationship between the amount of gouge and the amount of displacement of faults. I congratulate the author for developing a numerical relationship between them. However, I am concerned that the limits for applying this relationship be fully understood. An underlying assumption in this approach is that there is either a uniform thickness of gouge or breccia along a given fault or the thickness does not vary widely. Since it is not always possible to confirm this, the displacements derived by this method should be viewed with caution unless significant fault extent can be observed. At the Nevada Test Site, in drifts constructed in granite for test emplacement of spent nuclear reactor fuel, we found a fault with 0.3 to 0.4 m (12 to 16 in.) of clay gouge. Within a few meters of this location, the fault had no clay gouge, but rather consisted of a highly fractured zone with significantly altered rock and some slickensides. Based on Fig. 1, the 0.3 to 0.4 m (12 to 16 in.) thickness of gouge would indicate a displacement in excess of 30 m (98 ft). However, no gouge thickness would indicate essentially no displacement. Based on a quartz vein that terminated on the fault, and is not identified nearby, an estimated displacement of more than a few meters was made. This estimate is consistent with that obtained using the regression line proposed in the paper if the 0.3 to 0.4 m (12 to 16 in.) thickness for the gouge is used. However, using the regression curves with zero thickness would not yield results consistent with what was observed in the field. Therefore, it is important to recognize that the suggested procedure would properly yield a range of probable displacements. ? *Work performed under the auspices of the US Department of Energy by the Lawrence Livermore National Laboratory under Contract W-7405-Eng-48. Reply by E.C. Robertson It is certainly true that the t (thickness) of gg-bx (gouge and breccia) on a fault does vary along the fault. My observations have been that near the termination of a fault, the displacement d is small and the t is also small, whereas the maximum d and t will usually be found in the central part of the fault. The information on gg-bx and t of the fault found in granite in the NTS tunnel by Mr. Wilder could be interpreted somewhat differently than he does. He speaks of the fault changing within a few meters from 0.3 to 0.4 m (12 to 16 in.) of clay gg to "a highly fractured zone with significantly altered rock and some slickensides," but no gg. The highly fractured rock may be taken to be bx, rock not so finely ground as gg but still crushed by the fault movement, equivalent to the gg in my usage, and probably occupying about the same t. Mr. Wilder's estimates for the fault in the NTS tunnel for t of 0.3 to 0.4 m (12 to 16 in.) and for d of a quartz vein, in excess of "a few meters," would place the point on the low side of the central trend line in my Fig. 1, at the lower limit. There is, of course, a problem with determining d using displacement of only one planar surface. It would be greater or lesser depending on the rake of the movement. Finally, estimating the d of a fault from its t should be made with awareness of our present uncertainties, as pointed out by Mr. Wilder. Although the central trend line in my Fig. 1 has a ratio of d/t of 100, I have put the limiting ratios at 10 and 1000. Understanding of the values of the ratio will be improved only with collection of more data, for which the discussion of Mr. Wilder is much appreciated. G.C. Waterman E.C. Robertson's paper provides significant information to a geologist attempting to deduce fault offset by noting the products of structural dislocation. However, considerable mapping in underground and open-pit mines, and examination of structures produced in different geological settings, have convinced me that gouge and breccia thickness are controlled by geological conditions and fault movement. The following paragraphs suggest geological variables that control them. 1. Depth of Loading A near-surface fault resulting from tensional stress has more breccia/gouge than is produced by a similar stress at considerable depth. A deep-loaded compressional stress may produce a linear zone of schist, or structural dislocation may occur along an earlier formed belt of schist. Such "shear zones" are common in Canadian mines in precambrian rocks. In neither case can offset be directly deduced by an analysis of the minimal gouge/breccia in the shistose rocks. At greater depth, stress may be partially to wholly relieved by flowage. I vividly recall first noting the regional "Midas Thrust" in the Lark mine, Bingham Mining District, UT (where we called the structure the North Fault). My recorded notes, as I remember them, showed a narrow gouge streak separated the `Jordan" and "Commercial" limestone units from impure, muddy limestone beds of uncertain stratigraphic position. The visible structure did not indicate the great importance of this premineral fault

Jan 12, 1984

By B. A. Osei

Research to evaluate possible metrics for predicting dredgeability of compact aggregates, by hydraulically actuated clamshell dredges, shows work done by the pistons as a viable metric. Analysis of field data shows that there is a low, positive, correlation between cycle time (CT) and work done. If this correlation exists, then CT has to be considered an independent variable affecting work done during dredgeability assessment. Further research is required to elucidate the relationship between CT and work done during dredging. The objective of this paper is to test the hypothesis that work done during dredging increases with increasing CT. Kinematics and dynamics of the hydraulic clamshell were modeled and implemented in Simulink® in MATLAB. The model was validated using field data. The model was then used to test the research hypothesis. The results show that work done increases with increasing CT. This work confirms that work done during dredging increases with increasing CT. This result indicates that though an operator can increase the CT to deal with difficult digging, inputting unduly high CTs results in higher energy consumption during dredging.

Jan 1, 2011

By A. K. Dikshit, H. R. Murty, S. K. Gupta

This paper deals with the development of environment performance indicators (EPIs) for the steel industry. Environmental performance has become one of the key measures of business success. Emergence of continuing pressure from customers, employees, government and NGOs for environmental performance evaluation (EPE) of industries has led to evolve a framework for the development of sector specific environmental performance indicators. EPIs can be used by steel industry for assessing the continual improvement in environmental perfromance, selecting various eco-friendly options, benchmarking, environmental reporting, technology assessment and dissemination, evaluating environmental impacts and building EPIs based environmental management systems. The objective of this paper is to develop EPIs for steel industry and provide framework for development of environmental performance indicators based environmental management system and its integration with the overall management system. An indepth discussion has been presented concerning identification of EPIs, eavaluation of significance of EPIs, their prioritization and its integration with Environmental Management Systems. A new methodology has been proposed for implementing EPIs based environmental management systems . The material presented is derived in part from PhD studies of Rajesh Kumar Singh.

Jan 1, 2005

By Y. H. Zhan

A new P(MAAA) latex was developed and used in separation of ultrafine apatite from calcite and silica by means of selective flocculation. The latex was found to flocculate selectively apatite from apatite/calcite and apatite/silica mixtures in the presence of sodium tripolyphosphate and sodium silicate over a pH range from 9.1 to 9.4. The separation of apatite from calcite was more selective with sodium tripolyphosphate, while the results of the separation of apatite from silica were better when sodium silicate was used. In the apatite/calcite system, 90% apatite recoveries into a concentrate containing 34% P2O5 were possible in the presence of 4 mg/l of sodium tripolyphosphate at a latex dosage of 2.2 kg/t. In the apatite/silica system, 80% of apatite could be recovered into a concentrate containing 33% P2O5 in the presence of 20 mg/l of sodium silicate at a latex dosage of 1.1 kg/t. Deposition tests were used to study the interaction between the latex and the mineral surfaces. The results revealed that deposition density of the latex on apatite was higher than on calcite; the differences between the deposition onto these two minerals were higher at pH 9.2 than at 7.2. The results point to the stronger interaction between the latex and apatite surface when compared with the latex-calcite interactions.

Jan 1, 1998

By X. M. Yuan

In the flotation of Zn-Pb ores, sphalerite is floated following copper sulfide activation. In this type of sulfide ore, pyrite is commonly treated as a gangue, and poor selectivity between sphalerite and pyrite/quartz is often reported. But pyrite may also appear in association with gold, and flotation of such auriferous sulfides is of great importance in many countries (e.g. South Africa, Australia). In the cationic flotation of sulfide ores with dodecyl amine, sphalerite can be floated while depressing quartz and pyrite. While in a well-aerated pulp in the presence of lime (especially after oxidation with H2O2) the cationic flotation of pyrite is depressed, oxidation of pyrite in the presence of Na2S makes it floatable with amines even in very alkaline environment.

Jan 1, 2002

By S. Hadley, M. Placha, M. Mishra, V. Choudhry

Under a DOE-funded project, four advanced flotation technologies (the Jameson cell, the Outokumpu HG Tank Cell, an open column and a packed column) were evaluated at the benchscale to identify the technology or combination of technologies that best improved fine coal recovery and reduced processing costs. The results indicated that two-stage application of the Jameson and packed column cells provided the optimal performance. Subsequently, proof-of-concept scale testing was conducted at the Cyprus Emerald Coal Preparation Plant. The results confirmed that levelized production costs were lower using two-stage cleaning with the Jameson cell followed by the packed column.

Jan 1, 1999

By S. Ilyas

Technical innovation in electrical and electronic equipment with new functions and design, stimulate consumer?s purchasing desire towards the latest equipments and this leads the rapid increase in the production of increased amount of waste materials Treason et al (2006) have reviewed the data on electronic waste generation in different parts of the world. Studies by Bertram et al (2002) have also affirmed that waste electrical and electronic components are the fastest growing waste category; this emphasizes the need for efficient recycling strategies. Recycling of electronic waste is an important subject not only from the point of waste treatment but also from the recovery aspect of valuable materials. However, recycling of electronic scrap is still quite limited due to the heterogeneity of the materials present in the products (Veit et al. 2005). A bioleaching based process offers a number of advantages compared to the conventional pyro or hydrometallurgical methods (Lee et al. 2007; Lee and Pandey, 2012). The advantages include simple, inexpensive (in some cases) and eco-friendly approach besides, generation of less active leach residue then other metallurgical processes. Though, biohydrometallurgical process has been successfully applied for the leaching of metals from ores (Olson et al. 2003; Rawling 2000), data pertaining to its application for the extraction of electronic scrap is still scanty. Recently, a few studies have been undertaken for extraction of metals from electronic scrap/printed circuit boards (Brandl et al. 2001; Faramarzi et al. 2004; Choi et al. 2004, Ilyas et al. 2007; Ilyas et al. 2010). These studies were conducted with mesophilic chemolithotrophic (Acidithiobacillus ferooxidans and Acidithiobacillus thiooxidans) or cyanogenic bacteria (Chromobacterium violaceum) or moderate thermophilic bacteria (Sulfobacillus thermosulfidooxidans). However, compared to bacterial leaching, fungal leaching has the following advantages: (i) ability to grow under higher pH, and thus is more suitable in bioleaching of alkaline solid waste (ii) a generally faster leaching process with shorter lag phase (iii) Chelation of excreted metabolites (e.g. organic acids) with metal ion, thus reduce its toxicity to the biomass (Burgstaller et al. 1993; Aung and Ting 2005). The specific objective of this work was to; ? Collection, isolation and enrichment of fungal strain ? Evaluate the abilities of Penicillium chrysogenum to leach metals from electronic scrap at various leaching modes (one-step bioleaching, two-step bioleaching, spent medium leaching, fresh medium leaching, leaching with deionised water and chemical leaching). ? Comparative study of all leaching modes

Feb 27, 2013

By N. Ohmura, H. Saiki, T. Nagaoka

A microbiological flotation system that facilitates the removal of pyritic sulfurfrom coal is reported. The chemoautotrophic bacterium Thiobacillus ferrooxidans is utilized as a pyrite-selective biological surfactant that augments the flotation-mediated rejection of pyritic sulfur. The bacteria were produced by continuous cultivation in 50-L tanks, where it was possible to produce 3.8 x 1012 cells/day when the dilution rate was optimal and the pH was 1.6, a condition that prevented ferric precipitation. Prior to flotation, the bacteria were mixed with coal, which allowed cells to selectively adhere to the pyrite. The adherence of bacteria made the pyrite surfaces more hydrophilic, which facilitated separation by increasing the tendency of pyrite to sink, while the hydrophobic coal floated. When a synthetic coal/pyrite mixture (10.1 % sulfur) was subjected to microbial flotation, the level of sulfur rejection was stable during the entire period of operation (i.e., one hour). In the absence of bacteria, flotation reduced the sulfur content of a coal/pyrite mixture to within the range of 6.7% to 7.4%, with the combustible recoveries ranging from 93.9% to 99.0%. In the presence of bacteria, the sulfur content of cleaned coal was in the range of 1.3% to 1.4%, with the combustible recoveries ranging from 80.8% to 86.3%. Bacterial activity accounted for 57% of the total sulfur rejected through flotation. The desulfurization capacity of the system was further confirmed by testing it with run-of-mine coal. The pyritic sulfur content was reduced from 2.9% in the feed coal to around 1.2% in the froth product, while 80% of the combustible recovery was retained. Microbial flotation removed 60% of the pyritic sulfur from the feed. These findings demonstrated that micro¬bial flotation could be utilized for the removal of pyritic sulfur from coal in a semicontinuous system.

Jan 1, 2000

By Earl Rau

Introduction Will cogeneration be a major power source in the future? The location of electric power generating plants has changed. In 1900, more than 50% of electricity was generated by industrial plants. Since then, industrial plant generation of electricity greatly decreased to 17% in 1950 and to only 3% in 1980. Changing economics in electric power generating costs, though, may allow cogeneration to reverse this trend. Cogeneration has been defined as the simultaneous production of electric (mechanical) and thermal energy from a single energy source. Some applications are considered to be byproduct generation of electricity from industrial, thermal operations. Cogeneration is not new to the mining and minerals industry. Smelters and steel mills have used waste heat to generate electricity. Public Utilities Regulatory Policies Act of 1978 The potential for increased industrial cogeneration of electricity is related to the March 9, 1978 enactment of the Public Utility Regulatory Policies Act (PURPA). The US Supreme Court ruled that PURPA is constitutional. The court upheld requirements that utilities interconnect to cogenerators. It also ruled that 100% of avoided costs be used as the guideline for electricity sales by a qualifying facility (QF) to a utility. The state of New York established a floor price $0.06/kWh for electricity sales from a QF to a utility. It is obvious, then, that a cogenerator must first establish price and then become a qualifying facility in order to sell electricity to a utility. Proposed cogeneration plants The estimated industrial cogeneration potential for the years 1986 to 2000 is 9500 to 25,000 MW. Industries represented in this cogeneration estimate are pulp and paper, petroleum, chemicals, food, textiles, rubber, plastics, steel, lumber and wood, cement, glass, metal fabrication, and industrial parks. A cogeneration plant has been proposed for the Union Carbide chemical plant in Institute, WV. A steam turbine/generator would be installed to replace the pressure-reducing valve in the 2.7 MPa (400 psig) header. Scott Paper Co., Mobile, AL, proposed a cogeneration plant using a coal- and wood-fired boiler and a turbine/generator to produce process steam and electric power. A cogeneration system has been proposed for a large oil refining plant. A pulverized coal boiler would produce high-pressure steam to operate a turbine, generator. The exhaust steam from the turbine will go to the process and an existing turbine. Kansas City, MO's Armour meat-processing plant has proposed a cogeneration plant. This proposal is to use a natural gas or oil-fired, gas-driven turbine and a generator. The waste heat from the gas turbine would go to a heat recovery boiler for use as process heat. Dade County, FL is implementing a central energy system to supply electricity, air conditioning, and domestic hot water for five buildings in downtown Miami. The cogeneration system is to provide flexibility, to optimize fuel use efficiency while serving the variable thermal demands. Generation of electricity from municipal waste is not considered to be a cogeneration process but is covered by PURPA. Special considerations are provided for waste/electric power generation to encourage the development of these systems. ?

Jan 7, 1987

By Y. Nien Wang

The Devil?s Slide portion of Highway 1 between Pacifica and Montara is often closed due to the instability of the adjacent slopes. Following many years of public input and careful evaluation of alternatives, Devil?s Slide will be by-passed via two inland tunnels, providing a safe, dependable highway between Pacifica and Montara. For the twin tunnels, each 9m diameter tube will accommodate only one traffic lane. Each tunnel tube will accommodate a 3.6 meter roadway, 0.6 meter and 2.4 meter inside and outside shoulders respectively, and 1.2 meter walkways on each side. Cross passages will connect the bores at about 120 meter intervals and jet fans will provide tunnel ventilation. The twin tunnels are approximately 1,250 meter long and 9 meter wide. Excavation will progress from south to north using tunneling techniques that rely on inherent rock strength for support known as the New Austrian Tunneling Method (NATM). Both tunnels will be excavated at the same time, one tunnel face approximately 40 meters ahead of the other. Staggering the tunnels reduces the likelihood of damage from blasting in alternate tunnels. The work schedule is 24 hours a day, 7 days a week resulting in a 24-month timetable to break through to the north portal.

Jan 1, 2008

By M. Wiber, P. Nicoll

Rio Algom has embarked on a major programme of expansion with the goal of becoming one of the world’s top-performing base-metal mining and metals distribution companies. To assist the company and its operations in achieving its business objectives, we are implementing an environment, health and safety (EHS) management system, built to be compatible with the 14001 model. We recognize that a sustainable development approach for Rio Algom includes outstanding performance in EHS and community responsibility and is essential to earn acceptance within the communities where we operate or wish to locate; raise capital; obtain permits, and operate efficiently. We are committed to triple bottom line accountability, i.e. full consideration of environmental, social and economic concerns in our business decision making.

Jan 1, 2000

By W. W. Wen

A continuous pilot-scale test of the GranuFlow Process was conducted using a screen- bowl centrifuge for the dewatering and reconstitution of column flotation concentrate at a coal preparation plant in Virginia. In this test, a slipstream of the fine-clean-coal slurry from the column flotation concentrate was treated with a bitumen emulsion before dewatering. The treated products from the screen-bowl centrifuge appeared to be dry and in a free-flowing granular form, while the untreated products were wet, sticky, and difficult to handle. Specifically, test results indicated that the average moisture contents of the dewatered coal were 35.7, 35.5, 32.6, 29.9, and 26.5 wt% with Orimulsion additions of 0,0.7,3.2,4.8, and 6.4 wt%, respectively. The handleability and dust reduction of the dewatered coal product were also vastly improved.

Jan 1, 1997

By S. K. Samal, B. Mishra, M. K. Mohanty, S. C. Mishra

Steelmaking industries consume the majority of chromium and manganese ferroalloys to impart several properties in steel and also for other purposes. The quality of ore governs the process kinetics as well as the process economy of the ferroalloy industry. The present study demonstrates the thermal transformation behavior of chromite and manganese ores with varying compositions. Simultaneous thermal analysis (DTA/TG) is employed for such ore samples where the transformation of mineral phases is correlated with the thermogram characteristics and quantified. Phase, microstructure, and compositional analysis results of individual ores corroborated with thermal analysis are in good agreement. Chromite samples are ferruginous with goethite and gibbsite contents, whereas manganese ores vary in composition and also exhibit multiple and/or overlapping transformations.

Jan 21, 2021

By V. Bush, T. G. Killingsworth, E. P. Ruffel

Effective and sustained corporate energy management programs are becoming a necessity for energy users as electricity deregulation laws are enacted on a state-by-state basis across the country and environmental regulations pertaining to emissions become more prevalent. The “Total Energy Asset Management” (TEAM) approach has been developed to assist energy end users with the development and implementation of corporate energy management programs designed to reduce energy risks and increase energy cost savings. This paper highlights the ways in which this approach can be applied to the mining industry while minimizing initial program implementation costs and increasing potential program benefits. Nearly the entire mining industry has become very focused on identifying opportunities to reduce costs per unit of yield. The industry as a whole has increasingly faced pricing pressures in large part due to the effects of global competition. The result of international marketplace participation and the emergence of higher efficiency recovery techniques have resulted in flat or even decreased prices for mining products. Thus, opportunities to reduce costs are actually opportunities to gain a competitive edge over similar mining operations. Due to the energy-intensive nature of many mining operations, the costs associated with energy are often a substantial percentage of operating costs. Therefore, it becomes very important to develop the corporate mentality that energy is an asset whose use should be optimized globally. In addition to the cost benefits of the TEAM approach, other benefits may occur such as reductions in facility greenhouse gas emissions.

Jan 1, 2002

By D. McSwain-Santos

Soda ash is the trade name for sodium carbonate, a chemical refined from the mineral trona or naturally occurring sodium carbonate-bearing brines (both referred to as natural soda ash) or manufactured from one of several chemical processes (referred to as synthetic soda ash). It is an essential raw material in glass, chemicals, detergents and other important industrial products. Production U.S. soda ash production during 2004 increased to10.9 million Mt (12 million st). Five companies comprised the domestic soda ash industry. Four were in Wyoming operating five plants. One was in California with one plant.

Jan 1, 2005

By D. Denton, L. Buckingham

The dry grinding and leaching circuits of the Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs. Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes. The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper. The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility. Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike.

Jan 1, 2001

By W. W. Edgerton

Construction projects may be delivered under one contract package or multiple packages divided by discipline, geographic location, or other characteristics. Dividing the construction into contract bid packages is called contract packaging, and is a vital and strategic aspect of effectively delivering tunneling projects. The process of contract packaging considers many factors, including the type of project, location, and owner?s priorities. This paper describes the key facets of the contract packaging process used recently on several tunnel projects, reports, where possible, on the success of the process, and concludes with recommendations for applying this process to achieve the right contract package.

Jan 1, 2008

By Timothy D. Arnold

Barrick Gold’s Bullfrog underground mine, near Beatty, NV, was established as an after-thought to the main open pit. As open pit ore dwindles, the underground mining became increasingly more important as an ore source, and to the overall economics of the project. This situation is similar to many other mines. Today, there is a move towards underground mining in the United States. There are inherent problems in starting and operating underground mines in the shadow of any open-pit operation. Several attempts were made at the Bullfrog Mine for productive increases. Some were successful, while others were not.

Jan 1, 1996

Outokumpu Technology’s HSC Chemistry process calculation software enables the user to simulate an entire chemical or physical process. The HSC Chemistry 6.0 contains 21 calculation modules and 11 databases for reaction, equilibrium, heat balance, heat transfer, petrological and simulation applications. Most of the calculation modules automatically utilize the same extensive thermochemical database which contains enthalpy (H), entropy (S) and heat capacity (C) data. This database has been expanded to include more than 20,000 species.

Jan 1, 2007