Search Documents

By P. Harris, G. Groenmeyer, L. Parolis

The effect of molecular weight, charge and the presence of the cations Ca2+, Mg2+and K+ on the adsorption of carboxymethyl cellulose on pure talc obtained from Balmat, New York have been investigated. Higher adsorption densities were obtained in the presence ofCa2+ and Mg2+ ions than with K+ ions and higher ionic strength solutions resulted in higher adsorption densities. Changing the molecular weight did not influence the adsorption however increasing the charge (DS) of the polymers resulted in lower adsorption densities.

Jan 1, 2004

By L. Max Scott

[INTRODUCTION] The significance of gamma exposure to uranium miners has been recognized only in the last few years. Most ore deposits which have been underground mined, were 1% or less U308. Full-time mining of this grade ore can result in exposure exceeding 1 Rem per year. Several companies in Saskatchewan are planning to mine recently discovered ore bodies which contain ore pods in excess of 10% U308. The purpose of this paper is to present dose data which can be used to estimate gamma exposure from high-grade ore deposits, and to present mining techniques which will minimize miner exposure. [Dose Estimates] When one has a point source of radiation, the conventional laws of isotropic emission and the fall of dose with square of the distance, make dose calculations relatively easy. However, if one has an area source of infinite thickness, the assumption must be made that a uniform gamma flux is being emitted from all faces of the source (Figure 1). Dose from gamma emission would fall off only due to air attenuation up to such a distance at which the source can be considered to be a point source (usually 10 times the largest dimension of the source). For short distances, such as to the cab of ore-moving equipment, the dose reduction would be negligible. Assumptions: 1) Radium and gamma-emitting daughters are in secular equilibrium with uranium. 2) All gamma radiation is emitted from radium and its daughters. 3) Average gamma energy of 0.8 MeV. 4) Uranium ore has a linear attenuation coefficient of 0.212 cm-1, similar to that of Si02(sand). 5) Uranium ore density of 3.0 gm/cm3. 6) One curie of radium emits 6.84 x 1010 photon/sec(l). 7) One percent uranium ore contains 1 x 10-8 Ci/cm3 of radium. 8) Each MeV of 0.8 MeV photon results in a dose of 2.10[ ]10-3 mRem/hr. per MeV/cm2 -sec. 1) 9) Minimum ore depth 100 cm. 10) Linear attenuation coefficient instant for radium gamma of 0.374 cm -1 [ ] The photon flux from a radioactive slab is computed as follows: [Flux = photon/cm3 3(1) 2u S] [where, us is the linear absorption coefficient of s the source (uranium ore).] Thus, 1% uranium ore, in the form of an infinite slab, emits 1613 photon/cm2-sec, which results in a dose rate of 2.71 mRem/hr. Since the dose from an infinite slab is the same as a dose from an infinite radius right circular cylinder, the only correction needed from the above dose rate is for finite radius and point of dose above the end of the cylinder (Figure 2) [Dose = mRem/hr. {E2(bl) - E2(b3) - [(E2(b1sec[E] -E2(b3sec[E]]cos[O](1)]

Jan 1, 1981

By Eero Pokki

The Päijänne Tunnel is being constructed to conduct raw water from Lake Päijänne to the Helsinki Metropolitan Area. The length of the tunnel will be 120 km and the cross-sectional area is 15.5 sq m. Excavation started in 1973 and will be completed in 1982. 94 km of the tunnel have been constructed from Lake Päijänne towards Helsinki. The construction has advanced according to plan, and due to Finland's hard bedrock there have not been any great surprises. When completed, the tunnel will meet the water requirements of the Helsinki Metropolitan Area for a long time in the future because, with a free fall of 36 m, 9.6 cu m/s of water can be conducted through the tunnel from Lake Päijänne to the Helsinki Area. With pumping it will be possible to obtain a flow of 15 cu m/s, although at first the discharge will only be 5 cu m/s. The tunnel was partly taken into service as early as March 1979 when it was possible to conduct water to the municipalities north of the Helsinki Area. It is already possible now to conduct water to Helsinki, too, but from the Korpimäki pumping station onwards it must be done through the River Vantaa, which is polluted. When the tunnel is completed in 1982, good quality water can be conducted from Lake Päijänne to the Helsinki Metropolitan Area through a continuous rock tunnel. The cost estimate in 1973 was $ 88 million while it is now $ 90 million notwithstanding high inflation. AREAS NEEDED FOR CONSTRUCTION The areas needed for construction were bought through voluntary deals. Areas of 4 - 5 hectares were bought along the tunnel line at about 5 km intervals. The excavation of access tunnels was started from these places, and the crushed rock from the main tunnel was also transported there. However, it was not necessary to buy the area

Jan 1, 1979

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal', present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar' while the new design employed a 36.6 by 54.9 m' abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991

Western Energy Co.'s Rosebud mine in Colstrip, MT, has implemented innovative mining techniques in the past,* and following in that tradition, new techniques for overburden removal were recently introduced at the Montana coal mine. In April 1979, falling coal production left Western Energy in a bind. At that time the company was one of the first to implement a dozer/scraper stripping system for additional stripping capacity. This time around, however, the challenge was to eliminate spoil rehandle with a dragline while digging down 33 in. "Rehandle will increase 20% by going down an additional 3 m past the 24-m level," according to Bob Cope, mine supervisor for Western Energy. To cut this additional expense by eliminating the need to rehandle, Western now uses scrapers to bench down for the dragline. This system utilizes the flexibility of scrapers as earthmoving tools. Although scrapers were originally purchased to fill an immediate need for productive, low-cost overburden stripping, they are now benching and continue to optimize the overall effectiveness of existing draglines. According to the company, the draglines couldn't keep up with production requirements if they had to rehandle spoil material. Benching with the scrapers eliminates spoil rehandle. Western Energy expects to produce 10.6 Mt of coal this year from three active pits in the Rosebud mine. Western estimates that there are enough coal reserves at Rosebud to support a 40-50 year operation. The sub-biturninous coal has an energy value of 9.2-9.4 Mj, 0.87% sulfur, 8% ash, and 20% moisture. Pit A, approximately 610 m long and 45-55 m wide, is the mine's greatest producer. A Marion 8050 dragline with a 46-ms bucket digs 30-33 m to uncover the 7.3-m Rosebud coal seam. Here, the scrapers were put to work benching for the dragline. Long Construction Co., which operates the mine equipment for Western Energy, uses four Caterpillar 637 tandem-powered scrapers, two Cat 631s and two Terex TS-24s. The number and combination of scrapers actually used for benching periodically changes, depending on which ones are needed for topsoil removal and reclamation. Scrapers benched down about 9 m and removed nearly 2.3 Mm of over-burden at pit A. About 1 Mm was placed in a 9-m lift on top of the high-wall at the head of the pit. The scrapers built up one side of the lift first and then the other on successive passes to

Jan 2, 1981

By C. Wen

In Huoqiu region of Anhui Province, Fe2O3 occurs mainly in the form of specularite. Besides quartz, the gangue minerals include iron-bearing silicates such as chlorite and sericite which account for about 10% of the total gangue. The separation effect of conventional collectors is poor in the flotation of the minerals, that is, the average grade of iron concentrates is only 60-62%. Using the developed amphoteric collector can successfully realize not only the separation of specularite from various gangue minerals with results of iron concentrate grade above 65% and iron recovery of above 80% but also low temperature flotation at 15°C.

Jan 1, 2012

By C. G. Buttleman, W. C. Brice

In Minnesota, reclamation of active aggregate mining sites is primarily regulated through local permits issued at the county, township, or municipality. However, for abandoned or depleted aggregate mining sites, a responsible party for reclamation is often no longer available. Since 1995, the Minnesota Department of Natural Resources has reclaimed several abandoned aggregate sites using innovative public/private partnerships and emphasizing native plant materials. The purpose of these projects is to demonstrate cost effective reclamation methods that can be utilized by both aggregate operators and local government and to promote mine planning and resource identification as it relates to reclamation.

Jan 1, 2000

By Dermot M. Winters, Brent T. Wahlquist, C. Y. Chen

The enactment of the Surface Mining Control and Reclamation Act (SMCRA) in August 1977 addressed subsidence resulting from underground mines, in addition to creating the requirements for reclamation of surface coal mines. Subsidence control regulations pursuant to SMCRA were initially promulgated in March 1979. Several revisions have since been made. In addition, due to court challenges some regulations have been remanded and others are still on appeal. In the meantime the Secretary has agreed to initiate rulemaking on some issues. It is yet to be determined how the prohibition of certain areas from surface coal mining operations under Section 522(e) of the Act applies to subsidence. This presentation discusses the status of the regulations and issues related to or affecting the subsidence regulations.

Jan 1, 1986

By F. M. Jenkins

Improvements in miners? safety and health, as reflected by injury and illness statistics, have reached a plateau and even been reversed. Research into miners' OSH is a necessary adjunct to regulatory enforcement. Under the National Occupational Research Agenda (NORA) mining experts have come together to draft a national agenda for this research. The Mining Sector Council, one of ten NORA Sector Councils, has produced a draft national research agenda to guide all mining research entities: academia, government, and industry. The agenda has seven major objectives, each of which has a sequence of sub-objectives: Reduce the likelihood of disasters in mines; Improve mine disaster response; Improve the health of miners; Improve atmospheric control (ventilation) in mines; Improve health and safety through behavioral research; Improve mine design, systems operations, and management performance to enhance mine health and safety; Apply ergonomics, human factor engineering, to increase health and safety. Long-term maintenance of the Mining Research Agenda requires input from the public, both here and abroad, monitoring of the impact of research results using OSH data, and partners who will translate the research to practice.

Jan 1, 2012

By D. Brady

When deciding to deploy rescue teams underground the decision makers need to be able to determine that there won?t be an explosion whilst the rescue teams are underground. Previously general body concentrations in areas likely to be travelled were compared to explosive limits on a one off basis with no formal process looking at trends or other areas. A new approach is being adopted that takes into account the rate of change of gas concentrations with triggers set to enable a withdrawal of personnel prior to a possible explosion and influences such a barometric pressure changes. This paper explains the rationale behind the changes made and the advantages and implications of adopting such an approach.

Jan 1, 2012

By J. R. Kunkel, V. Lishnevsky

At mine sites, the operational and required storage volumes of solution and water storage ponds and reservoirs are usually calculated based upon a water-balance approach. Many climatological variables including precipitation, air temperature, solar radiation, pan evaporation and relative humidity along with operating parameters, are used in the water-balance model. The water-balance model often seeks to find a “critical period” of wet or dry climatological sequences which result in a “maximum” pond storage volume or water demand. The problem with this approach is that the designer usually does not know when the project will come on line in relation to the historical record. To avoid this pitfall, we use a more robust approach. In the more robust method, the water-balance calculations begin in each year of the historic climatological record. This method results in the same number of water-balance runs (or realizations) as the number of years of climatological record. Results of this type of analysis guarantee that the critical period or maximum required pond volume will be found if it is assumed that the historical climatological record repeats itself or if a synthetic time series is used. In addition, this method permits calculation of the likelihood (probability) that a given pond volume will be equaled or exceeded in any given month of the operational life of the facility. In this paper, the results of the sizing of a heap leach pad solution pond are presented along with the probabilities of a given solution pond size being equaled or exceeded based on the robust water-balance approach.

Jan 1, 2002

The last time Mining Engineering presented an issue with a special focus on Canadian Mining (ME, August 2008 pp. 28 to 40) things were going well. A feature story took a look at Xstrata?s Nickel Rim South Mine in Sudbury and the booming Canadian oil sands were discussed at length. Potash prices were soaring, large diamonds were being found and British Columbia was launching plans to find more workers. How things have changed in six short months. What began as a mortgage crisis grew into a credit crisis, then mutated into a financial crisis, that has taken its toll on the value of bonds, loans, stocks, real estate and commodities. Miners that were flying high on unprecedented commodity prices six months ago have begun scaling back with delays, shut downs and layoffs as they struggle to survive this most recent economic downturn.

Jan 1, 2009

By S. Hardcastle

Tele-remote operation of production equipment from surface will change the design criteria for underground mines. And for ventilation, with machine operators on surface, conventional planning to dilute and remove pollutants can become redundant. Natural Resources Canada with industrial partners are investigating what will be the new environmental design criteria. Additional complications include new mining equipment being designed without standard services and mines’ desire to eliminate conventional auxiliary ventilation. Findings to date show the cooling of equipment’s hydraulic systems to be the most demanding element, especially in dead-ends and when stationary. Consequently, revised ventilation based heat control strategies for equipment are being developed for the automated mine of the future.

Jan 1, 2001

By G. G. Marino, J. W. Mahar

This paper provides an utierstanding of the betivior and potenttil damage of homes resulting from sag-type mine subsidence. This is done with extemive research of numerom case histories in Illinois collected by the authors. The howe response to substience-itiuced ground displacements are summarized and evaluuted. A damage level criteriu, specifically developed for residenttil structures, is presented based primarily on repair costs. Damage levels and the associated subsidence profile characteristics for each case history are compared.

Jan 9, 1985

By S. C. Sun

A study(1) on the sulfuric acid extraction of alumina from some Pennsylvania ferruginous clays indicated that the published electrolytic method(2)(3) seems to be more efficient than the known chemical methods (4-9) for removing iron from the leach liquor. The main disadvantages of the chemical methods are the consumption of excessive amounts of reagents and/or the precipitation of prohibitive amounts of aluminum. In the electrolytic method, iron is deposited on the mercury cathode, while aluminum is not and remains in solution. This method, however, had been handicapped by the lack of an effective and economical way to purify the contaminated mercury cathode.(7)(l0). Described herein is a scheme for cleaning the mercury cathode, and for recycling the clean mercury back into the electrolytic cell. Armed with such an apparatus, the effects of applied potential, temperature, and operation time on the electrolytic separation of iron from aluminum sulfate solutions were determined. For the sake of comparing results, a term, removability, was coined to represent the percentage of iron amalgamated per unit height of electrolyte (cm.), per unit surface area of cathode (cm.2), per unit of operation time (second).

Jan 1, 1968

By Duane L. Abata

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during actual mining operations. The six explosives included two semigelatin dynamites, three slurry explosives and an ammonium nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and the toxic gases produced by the detonation were trapped to the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/lbm): NO, 0.010-0.035; NO2, 0.003-0.019; CO, 0.08-0.30; S02, 0.00-0.05; and CO2, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1979

By A. Gene Collins

The demand for lithium may increase because of its potential use id lithium batteries and in the generation of electrical power by fusion. Therefore, lithium abundance in some United States oil-field brines was surveyed. Oil-field brines from numerous locations were found to contain more than 100 mg/l lithium and several exceeded 500 mg/l. An area of 25,000 km2, with a reservoir thickness of 60 m, an effective porosity of 5 percent, and a brine with a specific gravity of 1.2 containing 100 mg/l of lithium, contains about 0.75 x 106 tonnes (1 tonne = 1 metric ton = 1,000 kg) of lithium in 7.5 km3 of brine. It is postulated that the brines were enriched in lithium by lithium-rich spring water or lithium leached from volcanic rocks followed by evaporation sequences.

Jan 1, 1978

By L. Shevenell, L. Stillings

The Acid Drainage Technology Initiative-Metal Mining Sector (ADTI-MMS) has established a Pit Lake Committee to enhance the science and understanding for the long-term management of pit lakes. Participation in this new committee is from members of federal and state agencies, industry, and academia, including numerous individuals representing 10 states. Work has begun on a pit lake literature search and review, database, classification, and sampling and monitoring procedures document. Coordination with the International Network for Acid Prevention (INAP) has been established. Future work will include preparing a prediction and assumption verification document, a report identifying variables upon which water quality is dependent, and an applied remediation technologies document, including an evaluation of the effects of backfilling.

Jan 1, 2002

By Alan A. Campoli

The US Bureau of Mines (USBM) conducted research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments. The goal is to minimize the over and under design of mine roof support, resulting in more productive and safer mines. To obtain the necessary data on roof behavior and support performance, USBM conducted several field studies. Each study covers roof geology, stress regime, ground reaction, support interaction and mining environment. A consistent experimental design is being used. This includes measurements of roof bolt loads and roof movements. So far, 10 studies have been conducted in several geologic settings.

Jan 1, 1996

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION This method is a variation of cut-and-fill mining where either the wall rock or the vein is too unconsolidated to permit safe mining by conventional cut-and-fill methods. Basic development consists of driving a 2.4 x 2.7-m (8 x 9-ft) haulage heading laterally in the footwall side of the vein. Crosscuts are driven over to the vein at 91-m (300-ft) intervals. Then the vein, at each inter¬section, is mined out to a distance of about 9 m (30 ft ) above the track level. After the installation of an ore chute, scrams or intermediate drifts are driven in both directions along the vein. Mining then starts imme¬diately below the level bounding the upper limit of the stope. A cut varying between 3 and 4.2 m (10 and 14 ft) in depth and mined for a distance of 45.7 m (150 ft )along the strike is taken from the orepass in each direction (Fig. 1). In this mined-out void, the floor of the cut is equipped with 203 x 203-mm (8 x 8-in.) caps hitched into the wall with steel saddle hitches installed on 1.5-m (5-ft) centers. Double wood stringers, 152.4 x 152.4 mm (6 x 6 in.), are then installed on 1.2-m (4-ft) centers longitudinally down the length of the stope. Reinforc¬ing wire mesh is also placed, overlying each mat of timber. Directly above the stringers, stulls are installed from hanging wall to footwall to hold the timber in place during the sand-filling operation. Then a cement¬sand mixture in a ratio of about 1:10 weight is poured to a depth of about 2.4 m (8 ft). The entire cycle is then repeated down to the scram drift. Another variation of timbering is illustrated in Fig. 2. There is a vein width of approximately 5.5 m (18 ft) with the same unconsolidated ground conditions. The primary difference between handling this situation and the previously described undercut-and-fill method is that standard timbered sets are installed in each excavated stoping void rather than stulls. Once again the basic method is to work down the ore block from an upper timbered drift to a lower timbered drift. Cuts are taken from a timbered raise with a chute on the stope side. Each piece of ground excavated is essentially two sets high, 5.5 m (18 ft), by two sets wide, 5.5 m (18 ft), by the length of the cut along the strike of the vein. The timbered sets are 2.4 x 2.4 x 2.4 m (8 x 8 x 8 ft). The net result is, therefore, two sets of timber on a top floor separated by doubled-up 76-mm (3-in.) lagging from

Jan 1, 1982