Search Documents

By D. -P. Georgescu

A native sulfur mineralization associated with pyrite and iron oxides containing 20% iron was quarried in Calimani Mountains, Oriental Carpathians. The wastes resulted from this exploitation activity, with a volume of 33 millions m3, were stored in four dumps while the wastes resulted from ore processing using flotation and the subsequent treatment were disposed of in a settlement pond. The investigations carried out in the entire mining area focused on the following two aspects: - the impact of environmental factors mainly on the hydrographic network; - the characterization all pollution sources, namely dumps, leachates and the quarry and the assessment of acidic drainage generation. The total sulfur content of the excavated ore was 3.8% while in dumps it ranged between 0.54 and 1.06%. Analysis of samples collected along the hydrographic network, draining the mining area, resulted in pH values ranging between 1.7 and 2.83 as well as high concentration of iron (4525 mg/L to 1.6 mg/L), copper (1.87 mg/L to 0.04 mg/L) and zinc (13.13 mg/L to 0.3 mg/L). Samples from the quarry, the dumps and the tailings pond were analyzed in order to deter-mine: - the maximum potential acidity (MPA); - the acid neutralization capacity (ANC); - the net acid production potential (NAPP).

Jan 1, 2005

By G. J. Olson

This paper describes the microbiology basics underlying heap and tank biooxidation of metal sulfide ores and concentrates. The primary organisms are identified and described along with the reactions they catalyze and their growth requirements. Also described is the interaction between ore leaching bacteria and the leaching environment in terms of solution chemistry, temperature, and mineral precipitation. Specific factors and agents that stimulate or inhibit growth and activity of ore bioleaching will be identified. Some of these factors are organism-specific and others are generic for microorganisms that grow under acidic conditions. Current knowledge of the limits of bioleaching in terms of dissolved ions in leach solutions, pH, and temperature will be summarized.

Jan 1, 2003

By H. C. Seeber

When considering all the aspects of a viable mine plan, it is important to estimate the accurate cost of mine ventilation, which varies as a function of airway dimensions, fan selection and ventilation network. Optimization of the overall elements of ventilation design can lead to very significant cost savings when capital and operating cost savings are considered in combination. This paper will describe a methodology, whereby ventilation costs can be minimized by optimizing the ventilation aspects of mine design and fan selection, by providing a brief description on ventilation theory and the factors which affect ventilation operating and capital costs.

Jan 1, 2002

By R. P. Killmeyer, W. W. Wen, B. K. Parekh

A continuous pilot-scale test of the GranuFlow Process was conducted using a screen-bowl centrifuge for the dewatering and reconstitution of column -flotation concentrate at a coal preparation plant in Virginia. In this test, a slipstream of the fine clean-coal slurry from the column flotation con¬centrate was treated with a bitumen emulsion before dewatering. The treated products from the screen-bowl centrifuge appeared to be dry and in a free flowing granularform, while the untreated products were wet, sticky and difficult to handle. Test results indicated that the average moisture contents of the dewatered coal products were 35.7%, 35.5%, 32.6%, 29.9% and 26.5% (by weight) with Orimulsion additions of 0.0%, 0.7%, 3.2%, 4.8% and 6.4% (by weight), respectively. The handleability and dust reduction of the dewatered coal products were also vastly improved.

Jan 1, 2000

By D. J. Turk

Stillwater Mining Company’s, Nye Operation has been producing PGM concentrate since 1987.Several expansions have allowed for increasing capacity from the initial rate of 500 tons per day, to its present capacity of 3,000 tons per day. The expansions were performed with minimal impact upon production and maximum utilization of the existing equipment. The latest expansion incorporates a 6’ X 18’ SAG mill, 13’ X 20’ Ball mill, pebble crusher, rougher flotation cells, 1250 Hp tertiary grinding mill, middling and scavenger flotation cells, and cleaner column flotation cells. This paper will describe the concentrator flow sheet, and controls for improved concentrator performance.

Jan 1, 2000

By M. Hamarat

Freeport-McMoRan Copper & Gold (FCX) is committed to preserving and enhancing biodiversity in the areas in which we operate. As a member of the ICMM, FCX is committed to implement the 10 Sustainable Development (SD) Principles throughout our business. FCX is also a member of the Wildlife Habitat Council (WHC), a nonprofit coalition dedicated to protecting and enhancing wildl ife habitat. In alignment with ICMM SD Principle 7 and our Environmental Policy, FCX has set a performance goal to prepare a biodiversity inventory in 2010 and land management plan by end of 2011 for all active mining sites. In 2010 FCX established a Biodiversity Task Force to assist sites in biodiversity management; optimize use of resources around the globe; implement FCX goals and targets; and align biodiversity programs with ICMM principles and guidance. The task force consists of Environment and SD Department management, scientists and engineers from FCX sites, and WHC staff. The Task Force recently issued a biodiversity inventory guidance document to set expectations and provide consistency across the sites when developing a biodiversity inventory and land management plan.

Jan 1, 2011

By T. R. Ellis

The author attempted to concurrently apply the US Uniform Standards of Professional Appraisal Practice and the Australian VALMIN Code to a complex mineral property appraisal assignment. This led the author into many severe difficulties. These difficulties included the high standards needed in the work of others, and information and statements needed from the client. The exercise also highlighted many positive features of both documents. Some conflicts were found between the two documents. Implications and thoughts regarding the development of a set of US minerals appraisal standards are discussed.

Jan 1, 2000

By I. Douni

The aim of this study is to synthesize hydrated compounds of calcium silicate (tobermorite) using as siliceous source perlite milling process wastes, containing more than 70% of SiO2. Calcium silicate hydrates are mainly used for construction of lightweight building materials, plasters, tiles and filters. The effect of temperature, time and particle size of perlite on the quality and composition of the solid product was studied. The solid products were characterized by X-ray Diffractometry, Differential Thermal Analysis and the amount of Acid Insoluble Residue. The synthesis of tobermorite was per-formed by the hydrothermal treatment of perlite waste with a saturated calcium hydroxide solution at a molar ratio CaO/SiO2 of 1, liquid to solid ratio 10 mL/g and 1% w.t. NaOH addition. Three experimental sets were performed. In the first series of experiments the synthesis temperature was kept constant at 205°C while the synthesis time varied from 0.5 h to 24 h. In the second experimental series the synthesis time was kept constant at 2 h while the temperature varied between 150°C and 245°C. In the third experimental set the temperature was 205°C and the reaction time was 2 hours and two perlite waste size fractions were used, a coarse (d50=18 µm) and a fine grained one (d50=8 µm). Reaction products consisted of semicrystalline calcium silicate hydrate (I) and crystalline Al-substituted tobermorite or a mixture of both. An isomorphic Si4+ ions substitution with Al3+ ions in the hydrated calcium silicate lattice was detected by thermal analysis. The experimental results show that good quality crystalline Al-tobermorite can be produced after 6 hours of autoclaving at 205°C or after 2 hours of hydro-thermal treatment at 225°C. Generally, the in-crease of synthesis temperature or time favors the crystallization of calcium silicate phases and enriches them in aluminum. The use of fine grain size perlite is more efficient for the hydrothermal synthesis of calcium silicate hydrates.

Jan 1, 2006

By C. P. Mangelsdorf

Introduction The use of frequency of vibration measurements to determine tension has long been accepted by industries that use electrical or stranded cables of wire ropes in their operations. In contemplating how to determine the tension in chords of a roof truss, it seems almost inevitable that a similar approach should be investigated even though there are some important dissimilarities in physical behavior between a chord of a rod-type Birmingham truss and a stretched wire rope. While the dominant feature of both types of behavior is the existence of tension, the bending resistance of the vibrating truss chord cannot be ignored. And it is common to have attached to the chord, pieces of hardware (turnbuckles, extension sleeves, wedge boxes) that represent concentrations of mass not usually found in a vibrating wire rope. Analytical solutions to the problem of vibrating wires or beams can be found in the literature on vibrations (Timoshensko, 1955; Den Hartog, 1956). But in every case, at least one of the ingredients of the vibrating truss chord is missing. The presence of axial tension, or bending resistance, of concentrated masses and of end conditions peculiar to truss chords is a combination that appears not to have been dealt with before, although the techniques for dealing with it are commonly known. The purpose of this note is to report the results of a project to measure and calibrate such frequencies. The work was conducted by the University of Pittsburgh under the sponsorship of the US Bureau of Mines. Field observations Tests were conducted on 24 different truss installations. The first 18 trusses were installed in shale roofs above Kentucky No. 9 seam and Illinois No. 6 seam. The remaining six were placed against the competent sandstone over the Pocahontas No. 3 seam in West Virginia. Chord tension was determined by two electrical resistance strain gages, in series, applied diametrically opposite to one another on the rod before tensioning. Due to the combined effects of inexact gage placement, rod bending and residual torsion in the chord due to tightening, errors in tension as high as 1780 N (400 lb) were reasonably possible. Due to faulty soldering or damage, three of the first 18 trusses and one of the final six were rendered completely unreliable. In addition to strain, the first natural frequency of vibration was observed to the nearest 0.1 Hz. Dimensions recorded included the span between contact points at the bearing blocks (Fig. 1) and the locations and amount of excess rod and rod gap at the wedge box and turnbuckle, respectively.

Jan 9, 1985

Due to deposit shape and dimension, narrow vein makes reserve modeling, geological control, stope design, drill and blasting more challenging. It needs high standard quality control as errors can be created easily, which could cause significant amount of ore loss or dilution. From channel sampling, survey control, reserve modeling, drill hole design, blasting, communication with underground drillers to backfill, this paper illustrated every step and its quality control of a long hole stope mining. Compared to other narrow vein mining methods (cut and fill and shrinkage), long hole stoping means higher production, less labor, and significantly lower cost when deposit characteristics allowed.

Jan 1, 2012

By W. Chae

The influence of solution ionic strength (IS) and electrolyte valence on the flotation behavior of malachite has been investigated. The microflotation tests were conducted over a range of solution IS (1?300 mM) at a constant speed (340 rpm), pH (9.5), flotation time (10 min), and sodium oleate dosage (5.3×10-7 moles/g). The size of malachite ranged from 45 to 53 µm, and two different types of electrolytes (NaCl and CaCl2) were employed. Electrophoretic mobility was also measured over the same IS range employed in the microflotation study. Overall, strong coupled effect of solution IS and ion valence was observed. Specifically, the flotability of malachite increased with increasing IS in the presence of monovalent cation (Na+) while the flotability increased up to 30 mM and decreased with increasing IS in the presence of divalent cation (Ca2+). Notably, the flotability of malachite was greater with the presence of Na+ compared with Ca2+ under high IS conditions (IS>30 mM). Consistent trend for Na+ versus Ca2+ was observed from the flotation results with different SO dosages. The characterization and flotation results suggested that the trend was likely attributed to the increased unfavorable interaction between malachite and bubble via the charge reversal of bubbles and malachite at higher IS in the presence of Ca2+.

Feb 27, 2013

By C. J. Burkhalter, H. Andrade, T. C. A. Gardner, J. P. Campbell

During the 1990’s several copper heap leach facilities treating crushed and agglomerated oxide and sulfide ore were constructed in South America. The majority of these facilities have been in operation for at least three years, during which time the operators have been able to monitor the performance of the heaps. The basis for the paper is a compilation of these operators’ experiences, leading to a discussion of the lessons learned over the past decade. Several key geotechnical issues are examined, focusing upon the integrity of the ore, drainage material and pipe network, along with the success of any inter-lift liners.

Jan 1, 2002

To preserve Washington Group International's quality of service in the mine operations area, the company has established a Supervisor Training Program to provide all levels of supervision with the required skills to meet objectives and guarantee consistent, excellent performance for each of our projects. A need developed to establish this training program internationally. The first international training session was held at the APEX San Cristóbal Mine in Bolivia. This paper discusses the program’s development, execution, results, and lessons learned with an emphasis on multicultural environments.

Jan 1, 2007

By T. R. Ellis

Minerals Appraisers/Valuers often find great difficulty or failure in attempting to employ the Sales Comparison Approach to the Market Value Appraisal of development and operating stage mineral properties. An important factor generally overlooked is a comparison of net operating income (NOI) margins on a per-unit-of-production basis between mineral properties, whether these be demonstrated or forecast margins. NOI margins can vary greatly between mines or quarries that are producing similar products. Ultimately, the expected NOI margin determines what a buyer is willing to pay for an income producing property. Common criticisms of the sales comparison approach by minerals appraisers are introduced. These are counterbalanced by raising some issues in the way the inputs for the Income Approach are usually derived by minerals appraisers, and by review of some conspicuous examples of the much too common misuse or abuse of the income approach in market value minerals appraisals. Example transaction analyses and sales comparison analyses are used to demonstrate the author?s methodology for adjusting units of resource in his transaction adjustment tables (see APPENDIX). The examples are used as the basis for discussion of ways to employ adjustments for operating economics and many other factors, while cautioning about the potential for double counting. The conclusions include a recommendation that minerals appraisers attempt to apply at least two of the three valuation approaches when appraising the market or fair value of development and operating stage mineral properties, the two being the sales comparison and income approaches.

Jan 1, 2011

By D. Jacobson

There are many different machine setup parameters and variables that affect the production of cone crushers in a mineral processing plant. One of these variables is the eccentric speed at which the cone gyrates. In June 2012, pilot tests were conducted on a 200 hp high speed cone crusher to determine the production and operating conditions over a wide spectrum of eccentric speed. Every plant will have variations in the ore characteristics and feed rates throughout the life of the mine, and at times throughout a single shift of operation, which result in non-optimal use of the crushing energy and inconsistent process control. For high speed cone crushers, the crusher will exhibit a different capacity, power required, and discharge size distribution as the speed ranges over the design limits of the machine. This study documents the measured variation in production and energy efficiency both when the crusher was ran at full capacity as well as when the feed to the crusher was not sufficient to run at full capacity. Overall, the results match theory and the capacity and power fluctuated by 25% and 17%, respectively, over the speed range when operated full while there was an overall trend of slightly coarser discharge size distribution as the speed decreased. The results with the fixed feed rate were more telling, as the crushers had 4-14% higher production when making a theoretical minus 12.5 mm product when operating at the optimal speed as compared to the worst speed in the ?typical? speed range for this application. Secondary analysis of the fixed tonnage testing also showed that the power draw was more consistent with lower magnitude spikes at the higher speeds (higher cavity level), as on average the standard deviation of the power draw increased from 7% to 18% and the peak power spikes from 20% to 48% over the speed range tested. The findings lay groundwork for more efficient plant design. Varying the speed of the crusher can be used to tune the crusher speed during commissioning, adapt to changing ore conditions over long periods of time, or be used as a dynamic input into an advanced control system. Each action above would serve to make the crusher(s) more productive and more energy efficient, and would also have mechanical benefits for the machine. Key Words: cone crusher, ore reduction, process control, crushing efficiency

Feb 27, 2013

By M. Galetakis, C. Roumpos

A sustainable coal industry needs to achieve a number objectives concerning mainly with superior utilisation of deposits and improved environmental performance. Modern quality control systems, which are greatly based on the on-line analysers, play an important role in achieving sustainability targets. This paper discusses the testing and application of on-line ash analysers installed in the Ptolemais and Megalopolis lignite mines in Greece and examines the possibility of using this type of analyser to control blending and homogenisation operations. The effect of the accuracy of on-line analyser to control process, when used for the characterization of low rank coals with complex and variable composition, such as greek lignites, is examined.

Jan 1, 2005

By Russell B. Dix

Laboratory column leach tests are used routinely to evaluate gold and silver ores for heap leaching. The tests are fairly straightforward. The ore to be tested is placed into an appropriately sized leach column. Then an alkaline cyanide solution is applied to the ore and the effluent solutions are collected. The effluent solutions are then put through a column of activated carbon to recover the gold and silver in solution. Zinc precipitation may also be used for silver ores or if the ore contains a significant amount of soluble silver in addition to gold. The length of the leach time in the tests is mainly a function of how quickly the precious metals are recovered from the ore. At the completion of the tests, the tailings are assayed and the recoveries determined from the calculated head grades. The amount of ore to be used for a test is partly a function of its crushed size. The coarser the size, the larger the sample size for the column. A typical small-scale laboratory column test on ore crushed to -12 mm (-0.5 in.) would usually be conducted in a 100- to 150-mm-diam (4- to 6-in.-diam) column 2 m (6.6 ft) in height, containing about 20 to 45 kg (44 to 99 lb) of ore. A comparable test on the same ore crushed to 50 mm (2 in.) would be conducted in a 200- to 300-mm-diam (8- to 12-in.-diam) col¬umn 2 m (6.6 ft) in height, containing about 80 to 200 kg (176 to 441 lb) of ore. Larger-scale tests can be run by increasing the column heights and diameters. Conducting larger-scale tests results in increased costs for sample procurement, preparation, and running of the tests. The additional data obtained from

Jan 1, 1989

By B. Salopek, D. Rajkovic, D. Rumenjak

In decision making support system, that are used in various fields of environmental protection (environmental impact assessment, environmental management systems, setting environmental standards and regulation, etc.), it is often important to apply various mathematical environmental engineering models. The question of linking environmetal engineering modeling to decision making support system used in environmental protection is not yet methodically solved. The reasons for that could be manifold. Decison making support systems, used in environmental protection, because they are simply taken from bussines decision making, are not often adequate for specific problems raised in environmental protection. On the other hand, there are great number of types of models in environmental engineering, what urges the problem of finding the way of their proper linking with decision making support systems. The application of fuzzy logic in that field is estimated as one of possible solution of the problem.

Jan 1, 2005

The HB 2500 hydraulic breaker attachment from Atlas Copco Construction Tools features Krupp percussion technology and a service weight of 2,500 kg (5,512 lbs). This makes it ideal for demolition, tunneling, trenching, foundation work, rock mining and secondary breaking. Suitable for carriers in the 29-to 43-t (32-to 47-st) weight class, the HB 2500 accepts maximum hydraulic flow of 219 L/min (58 gpm) at 18 MPa (2,610 psi) of pressure, and delivers an impact rate of up to 550 blows per minute. The HB 2500 features PowerAdapt, a new system that automatically shuts down the breaker in the event that it receives excessive oil pressure from the carrier.

Jan 1, 2006

By Bart Bartholomew, Randall J. Essex

INTRODUCTION In June of 2004, at the North American Tunneling Conference in Atlanta, an all-day workshop was conducted to review the application of Geotechnical Baseline Reports (GBRs) for underground construction. The moderator for the program was Bart Bartholomew, former President of Fruin Colnon Construction Company. The program involved commentary by a panel of engineers, owners, contractors, and legal representatives within the North American tunneling industry, as well as an extended audience discussion. The panelists were: Peter Douglass, President, Peter Douglass, Inc. Randall Essex, Executive Vice President, Hatch Mott MacDonald Joseph Gildner, Deputy Director for Technical Services, Sound Transit Randall Hafer, Esq., Kilpatrick Stockton Robert Fitzgerald Esq., Watt, Tieder, Hoffer, & Fitzgerald Kirk Samuelson, Senior Vice President, Kiewit Construction Group DEVELOPMENT OF PROGRAM FORMAT The focus of the program was to assess the state of the practice in the preparation of GBRs, and to discuss improvements that could and should be made with regard to their preparation, interpretation, and application. The approach used to achieve this focus in the broadest possible way was unique, in that it involved the panelists’ preparation of the workshop format and materials months before the presentation of the workshop. First, each of the six panelists was selected by the moderator based on their reputation and involvement in their respective fields of expertise, taking care to maintain balance and contrast within the collective pool of talent assembled. Following selection and agreement to serve on the panel, each panelist was asked to independently submit to the moderator a list of the six most pressing issues involving GBRs that they each frequently encountered in their individual professional experience. Each was asked to rank their issues in descending order of perceived importance. This process resulting in a pool of thirty-six potential or “candidate” issues for use in the workshop program. Contrary to the moderator’s expectations, there was surprisingly little duplication among the thirty-six issues submitted.

Jan 1, 2005