Search Documents

By Isabel F. Barton, Christian A. Rathkopf, Mark D. Barton

Rhenium (Re) is one of the rarest elements on earth and is a designated critical element in the United States and European Union for its uses in superalloys. Unusually among critical elements, Re is produced entirely as a byproduct of molybdenite (MoS2) mining, as pure Re minerals are extremely rare. However, Re concentration in natural molybdenites varies from a few parts per trillion to tens of percent. There are few known consistent patterns and no firmly established reason for this variation, making it difficult to use molybdenite Re content as a proxy for metal grades, a vector to high grades, a clue to the geological and geochemical nature of the ore deposit, a guide to overall Re resources or for any other of the applications that have been suggested for it over time. 

By S. K. Bhoumik, D. K. Sengupta, B. P. Singh

This paper deals with experimental work to improve the settling and filtration characteristics of an industrial sludge from an iron-ore mine using synthetic polymeric flocculants. The experimental work consisted of the characterization and evaluation of suitable flocculants to enhance settling and filtration rates. The optimum dosage of the flocculants were determined. The experimental results revealed that the settling rate can be increased many times, compared to untreated sludge, by using a suitable combination of flocculants. Compared to cationic and nonionic flocculants, anionic flocculants were found to be more efficient in sludge flocculation. The synergistic effect of two anionic flocculants produced the best settling conditions. Filtration test results also reveal that suitable flocculants can improve the dewatering characteristics of the slurry.

Jan 1, 1997

By Charles F. Herbert

The waves of prospectors who struggled across the wide Alaskan wilderness between 1898 and 19 10 came close to but did not actually find the rich copper/zinc/silver deposits strung out along 161 km ( 100 miles) of felsic schist in the remote Brooks Range of northwestern Alaska. They had heard rumors of gold in the valley of the Kobuk River, so they skirted the Arctic ice pack in the Chukchi Sea and, in a force at least 800 men strong, ascended the Kobuk River in 1898. Twenty-eight placer mining camps were established but only a handful survived for more than a few years. One of the placers that died rapidly was Ruby Creek. A map showing the location of Alaskan mineral deposits is given in Fig. 1. The Ruby Creek miners, disappointed with the scarcity of gold in that creek, followed copper-bearing float to two places where the float was especially plentiful. Pits, a short adit, and a shallow shaft uncovered copper carbonates, bornite, and chalcopyrite in fractured limestone but the remoteness of the district blocked efforts to sell the claims or to raise capital for development. Shortly after 1906, the copper prospects were abandoned and, except for an account published in 1913 by the US Geological Survey, they were forgotten, as were the names of the prospectors.

Jan 1, 1991

By Charles E. Barker

Striking similarities exist between the sediment features and facies formed in some modern heliothermal lakes and the characteristics of some ancient borate depositional environments. Heliothermal lakes are density-stratified with shallow submerged margins surrounding areally restricted deep pool(s) containing a dense brine overlain by a much less dense brine. The reflective brine interface allows solar energy to be trapped in the dense brine which may warn to over 900C. carbonate precipitated from the dense brine is the typical sediment produced in warm deep pool. The strong density stratification reduces turbulence in the lake so clastic sediment is deposited under most of the lake as finely-stratified mudstone-limestone couplets (varves). This depositional process results in clastic lake sediment interfingering with and enclosing a thick evaporite pod(s). Because deep pools can exist at the same time or through geologic time, the evaporite pod(s) may occur sporadically throughout the lacustrine beds.

Jan 1, 1988

By Masahiro Lnoue, Kenichi Uchino

Airflow velocity vectors by a forcing auxiliary fan at a heading face were measured in an actual size model gallery and an actual mine. The location of an outlet of ventilation duct gives significant effects on the airflow at the heading in the gallery. It was also found that there were several stagnated regions which may have danger of methane accumulation. The flow were also examined using the visualization technique by laser light in a reduced scale model. The flow in reduced scale model showed similar behavior to those observed in actual size galleries. The air velocity at the outlet has no significant effect on the airflow. It was found that a region to be ventilated by the direct flow of the exhaust fan is limited to a relatively short distance but a secondary flow region is generated near the heading face. CFD ( Computational Fluid Dynamics ) method was also developed to examine the airflow. The calculated results coincides with those measured by actual and reduced scale models. It is concluded that the CFD is useful tool for the analysis of ventilation at the headings.

Jan 1, 1997

By B. Slaker, M. M. Sears, G. Rashed

Ground falls represent a significant hazard at underground mines in the stone, sand and gravel (SSG) sector in the United States. Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) are conducting detailed investigations into the complex loading conditions at underground stone mines operating in challenging conditions. This paper presents the application of numerical modeling to analyze pillar and roof stability at a dipping underground limestone mine.

By Nasser Madani, SULTAN ABULKHAIR

The geological and geostatistical modeling of mineral deposits requires densely sampled drillholes that provide accurate and reliable hard data. Furthermore, quantifying orebody uncertainty through geostatistical simulation can allow mining engineers to assess long-term risk in mine planning. Nevertheless, ore deposits can sometimes lack dense drillhole information, reliable hard data with proper quality assurance/quality control (QA/QC), or sometimes both. This study is based on a coal mine located in the Republic of Kazakhstan, where an iron dataset is based on data from three newly drilled drillholes, and geological information comes from a massive collection of legacy drillhole data with no evidence of proper QA/QC. For this reason, a workflow was introduced to construct a representative training image from legacy data and stochastically model geological domains within these three drillholes using a multiple-point geostatistics technique. Once the geological model was obtained, a two-point geostatistics algorithm was applied to model the iron inside each geological domain. The direct sampling algorithm was chosen for modeling geological domains, and sequential Gaussian simulation for iron grade calculation. Both methods were extensively evaluated using different statistical tools and analyses.

Aug 1, 2022

By G. Brofas

Mt Giona situated in the floristic hot-spot of southern-central Greece has an especially rich flora that counts more than 1000 native vascular plant taxa (species and subspecies) and an important plant endemism that is estimated to be about 10% of the native flora. The danger of population reduction of rare and endemic plant species and the opportunity to use rare native species in rehabilitation projects are two different aspects of rehabilitation planning in Mt Giona. In this study, an inventory of rare and endemic species of the area, their classification into IUCN threatened categories and an estimation of their habitats vulnerability are provided. The results emphasize the necessity to develop a monitoring program to analyze population viability of certain threatened plant species. The creation of artificial micro-reserves on calcareous spoils derived from bauxite mining for the conservation of water-stress tolerant rare and endemic plants is also proposed. An inventory of the species that have colonized the mining spoils was also undertaken. Twelve of them are endemics. Seven native species, because of their biological and ecological features, were selected for rehabilitation purposes of disturbed areas by mining activities. Seed germination, aspects of their reproductive biology and seedling emergence after sowing in pots under field conditions were studied. The seed germination study in the laboratory led to the identification of the optimum germination conditions and the creation of germination protocol for each species. Seedling emergence depends on the sowing season and the mulching. The use of the above species is recommended for rehabilitation purposes. The creation of artificial micro-reserves on calcareous spoils derived from bauxite mining for the conservation of water-stress tolerant rare and endemic plants is also proposed.

Jan 1, 2007

By B. P. Boisen

INTRODUCTION The rapidity of onset, rate of increase, and magni¬tude of loads in an underground support system can be measured using load cells or pressure cells, whichever is appropriate to the type of support. These instruments should be installed at the various instrumented station locations immediately after excavation. If the loading of a member is of interest, the load should be measured, whereas if the deflection or strain of a member is of interest, the strain should be mea¬sured. It makes as little sense to use a load cell to allow computation of strain as it does to measure the strain and then back calculate the load. Tunnel steel set de¬signers today invariably rely on the early work of Karl Terzaghi, the basis for which is load, so load measure¬ment should be the main concern. The current trend of using strain gages on steel sup¬port systems stems from the inability by some to eval¬uate unusual loading conditions caused by uneven block¬ing. In fact, uneven blocking will obscure almost any attempt (whether with load cells or strain gages) to properly evaluate support performance. The load curve in Fig. I shows the development of a characteristic early peak load sometimes called the "rear abutment load" seen in many underground open¬ings. It is thought that the peak reflects the coupling of the rock and the support system, and that the magnitude will increase until some yielding, or minor failure, of the support system occurs. At that time, the slight deforma¬tion of the support system promotes the formation of minute shears in the opening walls, and these shears tend to distribute stress between the support system and the adjacent rock in proportion to the relative rigidity of the support elements and the rock. In normal rock, as a result of this stress redistribu¬tion, subsequent load magnitudes generally do not reach the magnitude of the early peak load. In physically unstable (squeezing) or chemically un¬stable (swelling) rock, however, the loads experienced after passage of the early peak load may in fact show a slow, continuous increase. One of the very important purposes of load instrumentation is to provide the means for recognizing such long-term adverse trends, thus enabling the proper remedial steps to be taken. Another purpose of load instrumentation is to pro¬vide a comparison between the magnitudes of the early peak load and the subsequent stable load. The ratio of these two loads is analogous to a safety factor, and may be used to evaluate the efficiency and economy of the support system design. Aside from considerations of economy, it may be well to design support systems which do not have excessively high ratios of early peak load to subsequent stable load. Should these ratios be exces¬sively high, the support system may be so rigid that the yield or failure associated with stress redistribution may occur with explosive violence. Load cells for use in mines, tunnels, and on con¬struction projects come in many forms. Almost all, however, employ the same procedures for installation, readout, etc. Therefore the following comments are almost universal in application. LOAD CELL INSTALLATION Load cells should be installed with bases parallel to the surfaces against which they bear. Care must be taken to orient the cells so that their signal cables are protected from accidental damage as a result of con¬struction, maintenance, or cleanup activities. Most electronic load cells are compensated for tem¬perature variations likely to be encountered during nor¬mal operations. However, if a large difference is an¬ticipated between the calibration temperature [21°C (70°F)] and the average operating temperature, the cells should be conditioned to the operating temperature for at least 8 hr prior to installation. This is to insure that the initial reading, made under no-load conditions prior to installation, provides a stable value to which subse¬quent measurements can be referred. Hydraulic load cells tend to be temperature sensitive and should be used with that in mind. Also, hydraulic load cells tend to be soft compared to electronic types and will sometimes allow movement to take place in a system intended to be semirigid. Furthermore, hydrau¬lic load cells tend to be difficult to read remotely. Care must be taken to use bearing plates on both sides of load cells which are sufficiently rigid and of high enough bearing capacity to prevent bending and crush¬ing under load. This is very important with tieback load cells (basically a ring of steel) which can easily dig into bearing plates. MAINTENANCE AND TROUBLESHOOTING Except for a direct hit by a miner's axe or flyrock from a blast, most hydraulic load cells are nearly in¬destructible and require little, if any, maintenance. Hy¬draulic oil on the bearing plates is a good indication of a leak and the need for corrective action. Field maintenance of electronic load cells involves protecting the instrument and signal cable from mechani¬cal damage and from unnecessary exposure to dirt and moisture, and recognizing and correcting damage and the effects of normal wear and tear.

Jan 1, 1982

By Jürgen F. Brune

The Fourth Industrial Revolution, that of digital technologies and their application, is rapidly impacting the mining industry, as it is manufacturing, transportation, agriculture, trade, and most other industries. Mining is about 40,000 years old and has its origins in Africa. Since its earliest days, it has experienced four distinct “revolutions” that each resulted in significant improvements in production, productivity, and safety and health: The First Revolution in the fifteenth through eighteenth centuries brought technologies that improved miners’ lives and health, including pumps, forced and mechanical ventilation with wind catchers and bellows, the wire rope and black powder, to name a few. Many simple, muscle- or water-driven machines have been pictured and described in great detail by Agricola who wrote De Re Metallica in 1556. Agricola was familiar with, and concerned about, accidents where miners fell off rotten, wooden ladders, acrid smoke, and dust that caused respiratory illnesses and diseases. He also knew the dangers of fatigue and recommended that miners should sing aloud to prevent them from falling asleep.

By Jr. Cook

Panned stream-sediment,geochemistry-based gold exploration in those parts of the southeastern Piedmont proximal to the Fall Line must take into account potential contamination from basal fluvial gravels of the Coastal Plain. Anomalies attributable to the incorporation of placer gold of Coastal Plain origin into modern Piedmont drainages have been identified in portions of Lee, Macon, and Tallapoosa counties, Alabama, and Baldwin and Hancock counties, Georgia. Identification of such multicyclic anomalies must be based on knowledge of the local maximum Cretaceous transgression, paleotopography, modern and paleofluvial system dynamics, and fineness trends and Au-Ag zoning in gold grains.

Jan 1, 1988

By M. Woodie

INTRODUCTION Information such as application review to choose the proper style of vibrating screen, parameters that determine the proper size of vibrating screen, engineering design information that governors proper screen design, review of topics that govern proper isolation from structural steel and other topics that dictate proper screen selection for applications will be presented in this paper. Topics like process and application information review to choose the style of screen and how material size and type influences proper type of screen selection (multi-slope, incline, horizontal, linear incline or dewatering) will also be discussed. Parameters will be reviewed that help size the screen for the application. The total amount of surface area to size a screen is critical to the overall success of a screen installation. Once proper style of screen is determined there is an engineering process that is required to design the screen to operate correctly in the environment it will be used. Finite Element Analysis, Dynamic Modeling, Field Vibration Analysis and other engineering tools will be reviewed to best implement a successful vibrating screen installation. TYPES OF SCREENS Multi-Slope Multi-Slope vibrating screens are used where sizing large amounts of tonnage on surface areas that would be smaller than conventional screening where roughly 6” (150mm) minus material is required to be sized. Occasionally larger particle sizes can be screened on the Multi-Slope machine but the effectiveness of the machine can be diminished with larger particle sizes and larger than 4” (100mm) screen opening. The most common and effective size range of screening with these machines is 2” (50mm) minus material. The Multi-Slope screen is used where particle size is not extremely important. Mineral processing, hard rock mining and industries where exact material size is not critical are best suited for this equipment. Because the aggregates industry requires very specific material sizes, the Multi-Slope screen is not suited for most aggregate screen applications. The key to the success of a Multi-Slope screen is proper material presentation at the feed end of the screen. This allows for the material to stratify quickly and disperse the fines through the screen quickly with a relatively thin bed depth at the feed end which allows the undersize material through the screen quickly.

Jan 1, 2019

By Andrea Brickey, RICHARD AMOAKO, Akshay Chowdu

Production forecasts derived from the medium-term schedule represent the best path forward for underground mining operations to achieve corporate and operational goals. Unforeseen circumstances, such as equipment breakdown, can cause significant deviations from established production forecasts in the short term. Such situations require timely mitigation of the effects of the deviations in order to stay as close as possible to the medium-term plan. This paper presents a deterministic mathematical formulation for short-term scheduling that addresses this challenge. The formulation is able to make up for deficits resulting from operational disruptions by minimizing deviations from medium-term production goals and medium-term activity start dates. We demonstrate this in a case study by simulating disruptions involving reduction in ore extraction capacity and development advance rate. Aside from the rescheduling capability, this formulation can help mine planners conduct analysis on the impact of various disruptions on the schedule. The formulation can help identify those conditions or disruptions that are more detrimental to the achievement of forecast targets, or otherwise. The formulation also affords mine planners the flexibility to prioritize one production goal over the other, depending on operational conditions at the mine. In the future, we seek to incorporate in the formulation respirable dust, diesel particulate matter and ventilation constraints in order to create more realistic schedules, and enhance miners’ health and safety.

Jan 1, 2024

By E. V. Kuzmin

The rock properties improvement means the exchange of natural properties: increase of stability, strain and compress tension, reduction of gas-liquid filtering property, increase Jung- module, other mechanical and physical parameters of rocks by injection the hardening materials, such as polymeric pitches, micro-or geocements by special technology under high pressure, to fill cracks. Flow of liquid materials between the rock units and hardening under high pressure create full redistribution of rock pressure in rock massif. There are many reasons to use this technology in underground mining, tunnelling, creation barrier technology in raioactive, chemical and other danger material site etc.

Jan 1, 1996

By M. D. Martin

Low metal prices and increasingly stringent environmental regulations, coupled with the threat of higher governmental royalties are adversely affecting both existing and new operations. Existing operations must therefore be run at maximum operating efficiencies to enable mining companies to survive and grow. Well planned and executed "outsider" reviews can help achieve this goal. Many mine managers and those who direct them resist the idea of "outsider" reviews for a variety of reasons, some valid and some not. Those managers who do bring in the "outsiders" are nearly unanimous in reporting that the exercise in self-discipline was well worth the pain and effort and repaid the cost many times over. This paper makes a strong case for "outsider" reviews and gives recommendations on the kinds of reviews to undertake. The authors draw upon their nearly 70 years combined experience, much of which has been in operations.

Jan 1, 1994

By David M. Mchaina, Allan E. Hall, W. C. H. Kruining, Alan Coode, Stephen Hardcastle

This paper details an investigation into the feasibility of recirculating mine exhaust air in Saskatchewan potash mines. This project was initiated following a previous study at Ruttan Mine, Manitoba, which indicated that recirculation of exhaust air to reduce winter heating costs was feasible. The potash industry was selected for study because the mines use a minimum of blasting in their production methods and the exhaust temperature is significantly higher than that of most metal mines. These factors simplify the monitoring system required and have the potential for greater waste heat recovery. A series of measurements of underground mine pollutants was made at the main exhaust and intake shafts in order to determine the feasibility of introducing controlled recirculation of exhaust air. An experimental recirculation circuit was created by opening two existing doors situated between the return and intake shafts. During this recirculation trial, the air quality parameters at the intake, mixed intake and exhaust measuring stations were monitored. The results obtained from a questionnaire circulated to the regulatory agency and the major potash producers together with results obtained from underground field studies at Central Canada Potash (CCP) Division of Noranda Minerals indicated that controlled recirculation of mine exhaust air has potential application in these mines either to reduce heating costs and/ or to increase the face air quantities. A recirculation system is to be designed in conjunction with CCP and the Saskatchewan Ministry of Labour, Mine Safety Unit to attempt to implement a working recirculation system for CCP.

Jan 1, 1989

By J. A. Cole

Santa Fe Pacific Gold's Lone Tree mine is located in Humboldt County, NV, 45 km (28 miles) east of Winnemucca. The mine currently operates a 1.74-Mt/a (1.92-million stpy) run-of-mine heap-leach operation and a 2.27-kt/d (2500 stpd) refractory gold¬ore-processing plant. Most of the mill-grade ore reserves are refractory, mainly due to pyrite and arsenopyrite encapsulation of the gold. The autoclave pressure-oxidation circuit was commissioned in February 1994 to process the refractory ore. Mineralogy unique to the Lone Tree deposit allowed for the design of a partial-oxidation process. It takes advantage of the heterogeneous nature of the pyrite morphology. Partial oxidation has resulted in an autoclave plant that is able to achieve low operating-unit costs (Figs. 1 and 2).

Jan 1, 1995

An incremental-analysis-based stope design and cutoff grade calculation method was developed for an underground metal mine project. Traditional stope design methods are typically very time consuming and lack consistency and accuracy by manually drawing stope shapes. For quick reserve calculation and economic analysis, a new method named "3D incremental analysis based stope design" was created for mine-wide stope designs. The key idea of this method is to replace engineers' manual checking of each incremental ring with one calculation of all the rings, and to build the final stope shape with the maximum values. This process was realized through a 3D ring grid setup and proper naming conventions for rapid calculations. With this unique but practical method, multiple options for a mine design were completed within a short time before the final selection of optimal cutoff grade and best stope designs for the project.

Jan 1, 2012

By David L. Moffatt, Leon Peters

A unique electromagnetic pulse sounding system for the detection and identification of geological and man-made anomalies which represent hazards in hard rock rapid tunneling operations is described. The main features of the system including a periodic video-type pulse interrogating signal and a probe structure that permits operational modes which either "see" or are "blind" to homogeneous-type targets are reviewed. The results of experimental pulse measurements on targets buried in the overburden and in a limestone medium are presented. Since the electrical properties of limestone are not radically different from those of a hard rock medium, conclusions based on these data should be valid for a hard rock media also.

Jan 1, 1997

By D. A. Kramer

Seawater and natural brines accounted for about 51percent of U.S. magnesium compounds production during 2004. Dead-burned magnesia was produced by Martin Marietta Magnesia Specialties from well brines in Michigan. Caustic-calcined magnesia was recovered from sea-water by Premier Chemicals in Florida; from well brines in Michigan by Martin Marietta and Rohm and Haas; and from magnesite in Nevada by Premier Chemicals. Intrepid Mining and Great Salt Lake Minerals recovered magnesium chloride brines from the Great Salt Lake in Utah.

Jan 1, 2005