Search Documents

By G. T. Austin

This is an overview of the gemstone industry with special attention on particular states within the united states. The U.S. Bureau of Mines, Department of the Interior compiled and analyzed the information contained in this report. The report should be viewed as a current "still photograph" of a dynamic system. The information presented on a specific gemstone or for a specific state can and will change with time. This overview presents historical and reference information on the principal gemstones and their production in certain states. The report is not a definitive work on gemstones within the select states or United states.

Jan 1, 1995

By S. El-Mofty, P. Zhang, N. A. Khalek

This article reviews different technologies used for beneficiation of siliceous and calcareous phosphate ores of different origin. The review sheds light on recent trends suggested for solving problems associated with separation of different impurities from phosphates. Applications of recently modified flowsheets as well as new reagents in the flotation of phosphate ores of sedimentary origin are highlighted.

Jan 1, 2003

By 000-000-604

HISTORIACAL INTRODUCTION Mineral processing has three principle branches, to quote Taggart, "Ore Dressing, which comprises the methods of separation of solids in inorganic crude by means which do not affect substantial chemical change; Extractive Metallurgy, which utilizes chemical reactions for separations of constituents from solids in inorganic crude; and, Fuel Technology, which employs both physical and chemical methods for separating and rearrangement of liquid gaseous and solid components in crude oil and natural gas, tar sands, shale oil, or coal." The scope of this handbook covers the first two classifications, that is, "ore dressing" and "extractive metallurgy," which have been combined in one term: "mineral processing." For a brief history of the development of mineral processing, one could well refer to the Introduction, Sec. I of the Handbook of Mineral Dressing by Taggart, Froth Flotation, Principles of Mineral Dressing by Gaudin, and the original Richard's Ore Dressing, volume No. 1, first published in 1903-1905. In these references and the references given in them a coverage of the history of "ore dressing" can be found and studied at the reader's leisure. For the history of extractive metallurgy as well as ore dressing, the bibliography in General References, taken from a History of Ex¬tractive Metallurgy by F. Habashi, will give a good background for those who are interested in more detail on the history of metallurgy in general. Mineral processing covers a very wide field as is illustrated by the topics discussed in Part II of this handbook and dates back to the early history of man which started with the production and use of native minerals such as gold, silver, copper, mercury, and meteoric iron which were washed or picked from deposits on the surface of the earth and worked because of their malleability. Later, melting was discovered and then it was possible to cast objects of these metals, excluding mercury. The discovery of a method for reducing the metal¬lic oxide probably was developed from melting fragments of oxides or roasted sulfides with charcoal, so that the native metal could be produced in simple blast furnaces such as are used today in rural parts of Spain, China, and elsewhere. Eventually, it was learned that iron could be readily worked when hot, which resulted in its replacing bronze for tools, weapons, and cutlery. Carbon dating and correlation with the Brittle Cone pine has

Jan 1, 1985

By N. I. Jayaraman

Dust scrubbers on continuous miners are steadily gaining in popularity. Recent US Bureau of Mines research on scrubbers is reviewed, with emphasis on development of a new type of water-powered scrubber that can he retrofitted to existing miners; comparison of scrubber effectiveness with blowing and exhaust line ventilation; and improving the quartz dust collection of flooded-bed panels.

Jan 1, 1990

By James L. Patton

Automation of mining increases the productivity of labor, thereby reducing the unit cost of labor. Such cost constitutes the largest portion of the direct or variable costs of producing coal. Therefore, any increase in productivity directly reduces variable cost. The large investment in mechanical equipment carries with it the burden of increased fixed charges. As the proportion of fixed cost to the total cost increases, the effects on the cost of production changes are amplified. Therefore, equipment must be fully utilized at all times. Averaged fixed costs rise with any decline in production. Such a situation forces coal companies to seek every means of main¬taining full production. Figure I will reflect the story on the relationship of production to cost.

Jan 1, 1962

By N. P. Reddy, Y. J. Wang

This paper describes an experimental setup for multiple fan ventilation systems at the ventilation laboratory of the West Virginia University Department of Mining Engineering. Housed in a 30-ft x 70 -ft room, the experimental setup consists of three 18-in., variable-speed, axial flow fans; an 18-in. -diam, fiberglass tubing; associated fittings for arranging networks; and a picot-tube measuring and data-acquisition system. The fiberglass tubing and fans can be organized into non-planar networks of two or three fans. The setup is mainly designed for studying the characteristic curves, operating points and fan stall for multiple fan ventilation systems.

Jan 1, 1993

By B. Strickland

The decision to accelerate development of Stillwater Mining's East Boulder Mine was made in March of 1998. It required the completion of conceptual designs by July of 1998. This was accomplished through teamwork and close cooperation of mine personnel, engineering firms and vendors, all working toward the common goal of developing an efficient and workable design. Early in the project, representatives of Stillwater Mining, Kilborn International, Parsons Brinckerhoff Transit and Rail Systems, Continental Conveyor, and H.A. Simons met to develop methods to bring the mine into production at a highly accelerated rate and to solve potential bottlenecks, including the movement of personnel, materials, and muck through a 5.6 km (3-1/2 mile) adit. This interaction, including companies not normally associated with the mining industry, led to innovative approaches and designs produced by Kilborn Engineering and Stillwater Mining.

Jan 1, 1999

By Peter Van deVelde

Many companies in North America because of economic or environmental reasons are considering reprocessing material from their waste ponds. The Japanese have developed highly specialized machines and techniques to reprocess industrial/mining wastes from settling ponds. This paper discusses the techniques and results of applying this technology to North American applications.

Jan 1, 1983

By Duane Jorgensen

Two types of factors direct the search for gypsum deposits-geologic factors and economic factors. The prime control and major economic factor is the market for the possible products. The major geologic factor is the control of the depositional environment, which determines whether or not a deposit exists within a given market area. After discovery of a deposit, the distinction between economic and geologic factors is not as clear as before, and the geologic characteristics of the deposit become the economic factors in evaluating the deposit for production and processing. The geologic characteristics are concerned with 1) the gypsum rock, 2) the host or country rock, and 3) geologic fluids, such as gas and water. Prospecting includes both original discovery and the continuing information-gathering period. During this time the above three characteristics of the deposit are determined, usually from core drilling, from phenomena observed during drilling, and from the core and hole. Important information and means of gathering it include sample analyses, sample volume, impurities and their distribution, water levels, aquifer tests, permeability measurements, rock strength tests, rock and overburden thicknesses, rock types, and direct observations of water and gas. Data gathered or inferred from all of these determine the mining or quarrying geometry and environment: which in turn determine the equipment, development, production, and processing costs. Impurities in gypsum deposits are very important in manufacturing processes. The impurities and their effects vary widely from inert minerals with little effect to reactive minerals with strong and mostly detrimental effects.

Jan 1, 1978

By E. L. Bohnet

The purpose of this paper is to translate a mining company's "Corporate Objectives" into usable and practical guidelines for long term mine design and production scheduling. These guidelines are required to ensure that both operating and development properties are designed and economically ranked on the same basis, and with the "current" Corporate Objectives in mind. Secondly, if both management and mining engineers have a better understanding of the cause and effect of corporate policies, then penalties and risks associated with various Corporate Objectives can be put into better perspective for management. Corporate Objectives, relative to usable guidelines for either short and/or long term mine planning, could be defined as one or more of the following four objectives: 1) Maximize the recovery of the economic portion of the defined geologic resources, and hence, maximize total non-discounted project cash flows and profits (most common approach in mine design), 2) Maximize the Net Present Value (NPV) of the after-tax cash flows from each existing or proposed project, either on an individual basis or in concert with other projects, including downstream processing facilities (primary method used to judge relative investment merit of a proposed development or operating concept), 3) Limit short and long term capital expenditures to a defined ceiling, 4) Maximize product output for the existing facilities in the short term, or conversely, keep commodity production at a constant level for a series of years.

Jan 1, 1994

By T. K. McMahon

Formally, a mathematical model could be defined as: A set of equations whose solution will approximate the response of a physical process or system to a set of stimuli which appear as parameters in the equations. The purpose of a mathematical model is to permit the rationalization of experience to proceed by simulation rather than by physical experimentation. In the application of digital computer control to an industrial process, the mathematical model of the process (subsequently called the process model) is needed to calculate the present process performance from the measured variables and to predict the response of the process to a control change. Functionally, the cardinal element in process model development is a concise set of control objectives. These, besides implicitly defining the boundaries of the system to be modeled, will determine the accuracy demanded of the model its nature: dynamic or steady-state, and so forth, The objectives should explicitly define what process efficiencies, production rates, qualities are to lie within the scope of the computer control project, thereby providing a basis for simplifying assumptions in the development of the model. This requirement, a limited set of control objectives, is so often disregarded in formulating industrial control problems that its repetition can scarcely be avoided.

Jan 1, 1965

By Ted M. Noskiewicz, James A. Ramsay

INTRODUCTION During the various stages of an underground project from inception through design and construction, probably the single factor of most interest and concern is the nature of the ground. The ground conditions more than any other item govern costs and feasibility; and although the methods available for assessing the ground have become increasingly reliable during the past thirty years, it is still very difficult in many cases to predict the behaviour of soil and rock during and after excavation. To help in this ground evaluation process, we have frequently supplemented the boring program with one or more large diameter inspection holes; and during the past eighteen years, seventeen of these holes have been constructed on tunnel projects which we have designed. There are references in the literature to similar inspection holes (1); however, as far as we are aware, no detailed description of them has been published. The behaviour of soil or rock during and after excavation and the effect of ground water on tunneling operations are of vital interest to tunnel designers and contractors. A comprehensive geotechnical investigation is therefore among the early and most important tasks carried out on a tunnel project and the backbone of every geotechnical investigation is the boring program. A series of borings, typically 50 to 100 mm (21 to 4 in) diameter, are drilled from which soil samples or rock core are recovered and the ground water observed.

Jan 1, 1979

By R. C. Hopper, A. A. Mathews, T. A. Lang

DESCRIPTION OF PROJECT The Straight Creek Tunnel site is located approximately sixty (60) miles west of Denver, Colorado, on Interstate Route 70 in the vicinity of Loveland Pass, in the Rocky Mountains. The ultimate project will consist of dual two-lane vehicular tunnels with a building at each portal to house mechanical ventilation equipment and other installations. The tunnels run virtually east-west on an ascending 1.64 percent grade for a distance of approximately 8,900 feet, and will pass beneath the Continental Divide at an elevation of about 11,000 feet above sea level. The maximum cover is 1,450 feet and each tunnel is approximately 48 feet wide by 50 feet high as excavated. The work now under construction consists of the North Tunnel, which initially will have two-way traffic. Ultimately it will be the west bound lanes for Interstate 70. The completion of the North Tunnel will be the fulfillment of a long felt need for better communication through the high Rocky Mountains of central Colorado and is a vital link in Interstate Route 70. The early planning for a vehicular tunnel through the Continental Divide began in the late 1930's and between November, 1941 and May, 1943 an exploratory pioneer tunnel

Jan 1, 1997

By J. Fox, C. Allen, A. Greth, K. Kocsis

"It is the duty of the mine operator to ensure the mine environment is healthy and safe for the mine workers. For deep and hot underground mines, this requires maintaining adequate working temperatures by means of mitigating the heat load generated by strata, auto-compression, mining equipment, explosives, ground water, and human metabolism. The heat load is best reduced by minimizing the amount of heat transferred to the mine air from these sources and through the use of efficient ventilation with effective cooling systems. The heat emitted by mining equipment and vehicles contribute a significant proportion to the combined heat load of an underground mine. This is especially a problem for diesel equipment due to the fact that besides heat, a large amount of water vapor is produced, which increases the humidity in the production workings. Diesel engines have proven advantageous in recent history due to their high power output and reliability. However, as mines continue to become more mechanized and deeper the climatic problems introduced by elevated heat generation will continue to rise. With that, the issue of heat generated by diesel equipment must be addressed. The economic alternative for diesel engine equipment fleets in underground mines is the electric engine. Technological advances in battery technology, increased mechanical output and improved reliability have made the electric engine significantly more competitive in comparison to diesel engines. Because electric engines do not utilize internal combustion, the heat produced by them is significantly less than of the diesel engines. Battery powered mining equipment likewise eliminate diesel particulate matter (DPM) produced by diesel engines. Utilizing battery electric equipment in underground mines provides many advantages, such as: (a) reduced heat load, (b) healthier and safer environment for the mine workers, and (c) reduced mine operating costs due to lower ventilation requirements. This paper will highlight the health and cost benefits of using battery/electric fleets versus diesel fleets in deep and hot underground mines. The study analyzes simulations produced from thermodynamic ventilation models. Early simulations show significant cost reductions in terms of net present value (NPV) when comparing the air volume requirements for battery/electric equipment versus diesel powered equipment for the same production rate. INTRODUCTION The competitiveness of the world mineral market demands that mine operators continue to increase production and decrease costs as commodity prices fluctuate in often unplanned directions. This has forced underground mines to operate at deeper depths and to become more mechanized to remain competitive. Because of these changes, ventilation challenges have continued to increase as the mines combat an enlarged influx of contaminants such as heat and diesel particulate matter (DPM)."

Jan 1, 2018

By T. A. Griffin

Gentlemen: The subject of this paper is: ADVANCED APPLICATIONS OF BUCKET WHEEL EXCAVATORS AND RECLAIMERS. Against an urgent world wide energy crisis, the role of bucket wheel excavators and reclaimers in the surface mining of fossil fuels and other ores has been raised to new prominence. This paper will review the reasons for the expanded application of bucket wheel technology, its unique contributions, and other factors relative to volume, cost, versatility, and efficiency. Today, surface mining is faced with the twin challenge of (1), accelerating the rate of removal of massive quantities of overburden and ore, and (2), replacing comparable high volumes of overburden back into the mined-out portion of the pit. Optimum quantitites for - a single electrical power plant now range from 5 to 15 million tons of coal per year. The use of bucket wheels offers the best method for meeting this challenge at lowest possible cost. For example, an advanced application that also satisfies environmental concerns involves the simultaneous functioning of two bucket wheel excavators during surface mining operations. Working at spaced intervals and different levels in conjunction with a transfer conveyor and stacker, one excavator removes the ore while the other one transfers overburden to a stacker that replaces it back into the open pit. The result of this continuously operating cycle is: (1) removal of ore and replacement of overburden back into the pit in massive quantities, (2) at accelerated volume and extreme low cost that cannot be matched by conventional loading machines of any size, and (3) fulfills a basic environmental requirement which is to

Jan 1, 1974

By Todd Kilduff, Ryan O’Connell

Pipe canopies continue to gain momentum as a reliable methodology for construction of excavations below critical facilities with minimal surface settlement tolerances, such as railroads or roadways. Two tunnel projects designed by Kilduff Underground Engineering in the Salt Lake City, UT area, each at varying stages of completion, had project design criteria for selection of a tunneling methodology to minimize surface settlement. Both projects consist of a pedestrian tunnel, one crossing beneath a major roadway in downtown Salt Lake City and the second beneath UPRR tracks. Both projects were in difficult, coarse alluvium/fan ground conditions with project criteria that resulted in minimal cover above the tunnel. For each project, a pre-support pipe canopy was designed, requiring the placement of steel, canopy pipes driven the extent of the tunnel length. The pipe canopy is installed using a trenchless technology and then excavated with SEM tunneling and shoring provided by traditional support of excavation methods. The pipe canopy pre-support method offers a low-impact method to install an underpass beneath critical structures by adding significant stiffness to the subgrade to mitigate surface settlement during the main tunnel excavation sequence. These case studies seek to communicate the challenges associated with pipe canopy installation in site-specific ground conditions and explains how these challenges were overcome. This paper aims to define the project risks and describes the pipe canopy methodology as a viable solution to mitigate surface settlement in low cover tunneling scenarios.

Jun 13, 2023

By Leonard H. Hoyle

The American Society of Association Executives is a professional society composed of nearly 10,000 individuals who serve as salaried executives on the staffs of more than 6,500 associations. Represented is the full range of international, national, regional, state and local associations...including trade associations, professional societies, philanthropic organizations and others. The dramatic growth of ASAE during the past 15 years is a manifestation of the growth of the association movement during the past two decades. This is not to imply that associations are a new phenomenon, because they have existed for thousands of years. Ancient civilizations show evidence of groups formed for mutual protection and advancement. In the transition from ancient to medieval time, trade associations and guilds came to serve an important function for the craftsmen and merchants they represented, encouraging the growth of new industries, improved processes and education.

Jan 1, 1981

By J. Steven Whisler

Corporate managers are facing increasingly demanding challenges as they seek to ensure compliance with environmental laws. Management also must deal with new liabilities created by environmental laws. These laws provide both private groups and governmental agencies with access to the courts to seek penalties, compliance orders, cleanups, or to forestall developments that could affect ecosystems. Environmental laws and liabilities are also affecting commercial transactions, including the availability of financing. Corporate managers must develop new and innovative methods to address these challenges in order to assure both sustainable industrial growth and stewardship of the environment.

Jan 1, 1991

By BERND SCHÖNHERR, JÖRG DEHNERT, PETER WINDISCH, JENS STOPP

The Quick-Erect Stopping System (QESS) offers a new way of reducing the radon exposure of miners in Germany, especially during remediation work in old mines. The QESS is a lightweight, modular and reusable construction kit of interlocking telescopic aluminum tubes, radon-proof foil and expanding foam. It is designed to seal off radon-rich parts of galleries within minutes. Originally, the QESS was developed to protect miners against radon exposure. Then, the QESS found the attention of several mine rescue teams at a German mining conference. Some mine rescue drills by The Student Mine Rescue of the Technical University Bergakademie Freiberg, Wismut Mine Rescue and Front Range Mine Rescue helped to improve the system and highlighted its potential for mine rescue operations. Now, the QESS is well-suited for small-scale mining. The QESS can be used to both protect miners from radon exposure and to support mine rescue operations. Moreover, the QESS was also successfully used in ventilation experiments.

By P. S. Hettinger

Land Application Discharge (LAD) is a useful method of disposing of waste water from mining operations and in certain climatic regimes, stormwater runoff. LAD systems function under the premise that metals, salts and nutrients in water are dispersed over a large area and are effectively assimilated into the soil profile. Depending on the soil structure, migration or mobilization of dissolved metals through the soil profile can be Substantially reduced. Land application of treated effluent from sewage lagoons or waste water plants was probably the first general use of land applied water. LAD has gained popularity with the mining industry as a means of disposing of waste water and process water. In addition, large volumes of snow meltwater and stormwater are often placed in storage in Montana during spring, and Land Application Discharge has shown to be an effective method for disposing of stormwater during the dry, summer season. LAD can also provide an alternative to recycling or treating waste water at on-site waste water treatment plant&. Application of stormwater or process water can result in little or no change to the background concentrations of metals in baseline water quality samples. One cautionary note about LAD: high salt concentrations and pH values are associated with process water from heap-leach facilities and are known to cause burning of local vegetation. Some pre-treatment of process water may be necessary to prevent such environmental problems.

Jan 1, 1994