Search Documents

By Peter Sullivan, Johan van Heerden

Increased use of continuous miners and roadheaders in the underground coal mining industry in South Africa has led to improved productivity and efficiency of operations. Of major concern, however, is the increased amount of airborne dust generated during mining. Dust is a health hazard in terms of respiratory diseases, can impede productivity and is the major contributor to the potential of underground explosions. The concern of the South African coal mining industry with regard to the underground dust problem has led to the establishment of a Dust Control Section in the Coal Mining Division of COMRO. In the field of dust suppression system evaluation and design, collaborative work has been undertaken by COMRO and FLOSEP. This paper gives a review of the application of Computational Fluid Dynamics (CFD) in evaluating and improving environmental conditions in continuous miner and roadheader sections. A brief history of the development of the CFD model as well as a discussion of a typical application is included.

Jan 1, 1993

By A. Haghighat

A risk analysis on mine fires for all U.S. underground coal mines from 2000–2012 was completed to identify locations that have a high risk for fire incidents. The data for this analysis was extracted from the Mine Safety and Health Administration’s (MSHA) mine fire accident reports database. After identifying fire incidents from this database, a risk matrix was developed for underground locations that showed a significant propensity for fire incidents. This matrix associates the hazards and risks with the severity and frequency of their consequences at each location. These significant mine areas will be the concentration of future studies in fire behavior, suppression techniques, and simulation methodologies. INTRODUCTION Fires in underground mines pose significant hazards to personnel because of inherent restrictions to movement and limitations to egress routes. Despite improvements, mine fires remain serious hazards in underground coal mine. In order to better mitigate the risks from fire hazards in the modern underground mining environment, a better understanding of where fire events occur must be gained. The following paper presents an investigation on the number of fatal and non-fatal incidents in underground coal mines fires from 2000 to 2012. Three phases of risk assessment (i.e., risk identification, estimation, and evaluation) were applied to the recorded fire events from the MSHA incident database that occurred during this time period. Using this process, a fire hazard was first defined. This definition was then used to identify any incidents that had occurred as a result of the defined hazards. The seriousness of the injuries and damages were finally quantified for each incident though an estimate of severity and frequency and then aggregated according to underground location (ISO, 1999; Van Duijne, 2008). Using this approach, locations prone to incidents resulting from fire hazards were first identified. The risk for the occurrence a fire incident in general was then estimated for each of the identified locations. The results of this assessment will be used to improve fire simulation techniques for the identified, high risk underground locations. RISK IDENTIFICATION A risk for this assessment was defined as any single occurrence of a fire initiated by the ignition of gas, dust, or electricity. Each recorded occurrence of such an event in the MSHA incident database was counted as a single fire incident. Both non-fatal incidents that were reportable but did not result in a fatality and fatal incidents that fell into the aforementioned criteria were counted. Incidents in the MSHA database that were already classified as “generic” were not considered. The remaining incidents were then totaled and aggregated according to the underground location in which they occurred. In previous studies, a number of locations, which are listed in Table 1, were highlighted as high fire hazard areas (McDonald et al, 1980; Pomroy et al, 1995; De Rosa, 2004). These locations were used to group the fire incidents extracted from the MSHA incident database. The compiled numbers of non-fatal and fatal underground coal fire incidents from 2000 to 2012 are displayed in Table 1.

Jan 1, 2019

By Jacob Grasmick, Bill Newns

Despite ongoing digitization and “hardware” technological advances, geotechnical uncertainty remains the most significant risk in underground and tunnel construction. And, whilst they are commonly held up as an example of the sophistication of the industry, the practice of drafting and using geotechnical baseline reports is subject to a wide range of influences, not all of which support good risk management. Uncertainties in predicting ground behavior, the gap between the pre-construction assumptions, and the systemic response to construction remains a significant technical and communication challenge. Accordingly, this paper presents a framework to quantify geotechnical uncertainty using geostatistics and translate these into practical tools for ground risk management throughout planning, procurement and construction. Adopting even some of the principles of this framework should provide improvements to contract risk management and should assist to minimize the potential for commercial losses.

Dec 1, 2022

By M. Westendorf, T. Banerjee, S. Kaushik, D. Tinney

"Cyclones are one of the most extensively used pieces of equipment within the mineral processing industry because of their simplistic operating and maintenance philosophies. They are commonly used as classifiers within the comminution circuit to control the grinding product particle size for satisfactory performance of downstream operations.Cyclones are a key contributor to the effective operation of the plant and have a significant impact on the mineral processing plant operations. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput. Similarly, an inefficient cyclone operation may also lead to low or high recirculating loads that impact the efficiency of the comminution circuit. This highlights the importance of having proper stability in cyclone operation while implementing any plant-wide optimization strategy.One of the key challenges in cyclone operation is that cyclones are highly sensitive to changes in operating conditions and are affected by process fluctuations such as feed pressure, solids concentration and flow rates. Fluctuations in cyclone feed characteristics lead to unstable cyclone performance which affects mineral liberation. For such an impactful unit operation, cyclones have historically been under-instrumented in an otherwise highly instrumented process plant. Traditionally, mill operators have relied on visual observations of the apex discharge to determine the operating state of the cyclones. Visual cues corresponding to the different cyclone operating conditions have been discussed by Neesse et al. (2004) as shown in Fig. 1."

Jan 1, 2014

By Jerry W. Danni, John E. Hardaway

Corporations today must comply with an ever growing number of complex and increasingly stringent environmental laws and regulations. An environmental audit program is an effective means in which to uniformly and systematically assess compliance, and to assure management that environmental liabilities are being minimized. This paper describes the design and implementation of Homestake Mining Company's environmental audit program, which has as its primary focus the objective verification of compliance with external requirements and internal good management practices. Major elements of the audit program discussed in the paper include: pre-audit preparation; on-site audit activities; and the post-audit report.

Jan 1, 1992

By C. Woofter

Quarry operators must continue to change and adapt environmental compliance methods to meet the increasingly demanding regulations. To fulfill industry needs, a computer-based decision support system is being developed to facilitate decision making that mine operators are required to make regarding environmental responsibilities. This system can help to determine permitting and compliance measures needed for air, surface water, groundwater, noise, aesthetics, vegetation, wetlands, hazardous wastes, storage tanks and wildlife habitats during the development, operation, and closure phases of mining. Operators will utilize the system's user-friendly interface consisting of mouse driven responses and limited keyboard entries on a desktop computer. The system is easy to upgrade according to the user's needs and changes in current laws and regulations. Data input models, user interfaces, and support of decision making are explained. The program permits inclusion of the decision maker's own insights through "what-if' analysis, in which the user can change ad hoc entries and check the related consequences. Using this approach, the user has complete control over all steps of the decision making process. A storm water example is selected to demonstrate the potential benefits of the support system to environmental decision makers.

Jan 1, 1995

By Kalle Hakalehto

Automation and mechanization in mining has no value of its own. It has to be measured in economic terms or in Increased safety or in the utilization of deposits which otherwise were unavailable. The mechanization and automation of workphases in the mining and rock construction process has led to the decrease of manual work. This has had a very essential importance in the countries where the labor is expensive or where there has been difficulties in the availability of labor. The work has become much more efficient. We would like to argue that the need of mechanization has been initiated mostly from the above mentioned reasons. The origin has seldom been the "process" approach or the real need or will to change the way mining is done. Through mechanization bigger unit sizes of machines and operations have become possible and better efficiency is achieved. This has led to new problems as well, but in most cases they have been solved so that better and more economic outcome than before has been the end result. The changes have thus been justified. It is perhaps feasible to state already at this stage that we see that the mechanization andautomation steps in the difficult conditions of mining have been remarkable. There is not a slightest underestimation of the achievements and importance of this development in our mind. Where we are to- day is the result of the experience, know-how and technological excellency of all the parties involved. The natural approach to automation has been through mechanization and automation of individual unit operations and machines. This has been the way as well in manufacturing industry as in mining. There may not have been any other way. The other presentations in this session tell us very clearly of the approach .which the machine manufacturers have taken. They have not done it alone but 'most of the initiatives have come from them. A good use of their present achievements gives many possibilities to increase the, efficiency in mining. We would, however, like to extend the view one step further to the future:

Jan 1, 1989

By Don Rose

Steel-fiber-reinforced-shotcrete (SFRS) methods of testing and the wording of specifications vary from country to country. In the USA ASTM C1018 is widely used. The Canadians have taken a close look at C1018 and point out that exact determination of the first crack is very subjective, and they propose a method of design that eliminates this variable. The Europeans (EFNARC) have taken the principles of testing a step further than ASTM C1018, and have added a new step in measuring the effectiveness of SFRS. EFNARC uses an "energy absorption" of a plate loaded in its center, in addition to the principles of C1018. The principles of SFRS design are also used in Japan, Norway and elsewhere.

Jan 1, 1999

By Numan Elmas

This paper presents detailed information on the genesis, formation, and industrial utilization of Yaylacik magnesites. Tectonically, the study area is located within the Tavsanli Zone, immediately south of the Izmir-Ankara suture in western Turkey. The geologic setting mainly comprises ophiolitic melangks basics, and ultrabasics associated with very rich magnesite deposits and lacustrine sediments. The ophiolitic unit tectonically overlies the schists and carbonate rocks. The presence of glaucophane and lawsonite indicates a low-temperature/high-pressure metamorphism. The ultra- basic rocks, which exhibit cumulate composition, have been mostly serpentinised and represent the oceanic floor of the Yaylacik ophiolite. Basic intrusives consist of dolerite and diabase, and they show the characteristics of within-plate dolerites. The magnesite occurrences are commonly observed in block, stockwork, lens, and vein forms and were deposited within the serpentinites. In most magnesite samples, secondary quartz/chalcedony formations are observed as fracture fillings due to the highly effective tectonic movements. Field surveys and microscope studies reveal that magnesites had been formed by the metasomatic alteration of serpentinites. Chemical analyses show that, although MgO content of the magnesites varies from 43.41% to 50.48%, Fe203 and CaO are lower than 1%. Silica contents are as high as 5.52% in a few samples. Although Yaylacik magnesites are not suitable for making basic refractory bricks, they are widely used as caustic-calcined magnesite in a variety of applications, including animal food, artificial fertilizer, chemical (acid neutralizer), medical and pharmaceutical, and water treatment.

Jan 1, 1999

By S. S. Churchill

Introduction Amidst the apparent chaos of the final push to complete a major construction project, a small group of specialists works with great intensity. Armed with yellow "in test" and green "turned over to operations" tags, these startup engineers follow detailed preoperational test procedures to confirm that a plant is ready to operate. They follow a test schedule designed to complete individual process system in the order they will be needed by operations. After extensive preliminary testing, the startup engineers begin the truly exciting part of their work - initial operations. The thrill of engaging the clutch for the first time on a 10,000 horsepower grinding mill makes all the long hours worthwhile. Preoperational testing and startup are of critical importance to the success of a project. No other aspect of a construction project allows such opportunities for success or failure, and no other aspect is so critically influenced by careful planning. At Bechtel, the tasks of preoperational testing and startup are among the responsibilities of the Mine and Plant Operations group. The Preoperational Testing Process Preoperational testing is the transition phase between constructon and startup on a new plant. It includes the preparation of detailed test schedules and procedures. The schedules are used to coordinate construction completion activities, so that systems are available for startup and operations in a rational sequence. The procedures form the basis for performing the testing and documenting its completion. Tests include instrument calibration, wire insulation tests, wire termination verification, mechanical alignments and inspections, and system cleaning and flushing. Where possible, the systems are then operated on water and their performance recorded. Normally, either the construction contractor or a team of specialists has the responsibility to perform preoperational testing. Witnesses to the testing may be owner operations and maintenance personnel, engineers from the design firm, or specialists assigned to the project who provide assistance and guidance to the contractor in addition to witnesing the work.

Jan 1, 1986

By John L. Burnett

Field criteria are needed to help the prospector recognize a potentially expansible shale, clay, or slate. Certain criteria have proven useful in California even though the physical-chemical mechanisms of expansion are not thoroughly understood. Three conditions must be satisfied before expansion can take place, The raw material must partially fuse at a low temperature (1800-2000°F.), Concurrently a gas must form. The raw material must be sufficiently impermeable to trap the gas within the particle. Low temperature melting, which is controlled by bulk chemical composition, is difficult to assess in the field but most common shale, clay, and slate is suitable in this respect, The presence of organic carbon, the most common source of an expanding gas, is indicated by dark color of the rock, A large proportion of clay-sized particles promotes impermeability; fine grain-size is indicated by conchoidal fracture, The shape of the expanded particle is commonly indicated by the texture of the raw material. Rocks with well-developed slatey cleavage produce accordion-shaped particles; massive rocks tend to form rounded particles. Undesirable materials commonly present with expansible shale include: weathered shale; sandstone and other coarse-grained sediments; and limestone, Weathering, which is indicated by color, reduces or eliminates expansion; therefore, surface samples seldom are representative of the shale found at depth. Sandstone does not expand and will increase the average weight of the finished product, Limestone or particles of carbonate minerals can be actively harmful because they are converted to free lime (CaO) during the firing process, If free lime is present in concrete, hydration will cause expansion of the lime particles which result in surficial ?popouts.?

Jan 1, 1963

By K. K. Haramy, J. McDonnel

INTRODUCTION Primarily because of mining at greater depth, an increasing number of coal mines in the United States experience floor heave problems. In many instances, the floor heaves at a slow rate without causing health and safety related problems; only additional roadway maintenance and coal handling equipment are required. However, when rapid, massive heaving occurs, the safety of mine personnel in the vicinity is jeopardized. Extensive floor heave causes a redistribution of stress around the mine opening and can cause additional ground control problems. This paper presents an analysis of rapid floor heave in a deep western coal mine. The analysis is based on field measurements, laboratory data, and beam design theory. Factors affecting floor heave, such as mining-induced stress, mine opening size, entry orientation, mine geology, rock physical properties, and gas pressure, are considered. Examination of floor heave in the mine indicates that heaving is primarily caused by deformation of a soft floor member that is subjected to high mining-induced stress. Theoretical analysis of in situ floor stresses resulting from overburden loading indicates that floor failure will occur. The analysis is confirmed by visual observations of floor heave in the mine. Recommendations for mine layout and opening design to control rapid, massive floor heave under these conditions are also presented. MINE-FLOOR-FOUNDATION THEORY The floor stratum in a coal mine acts as a foundation to support coal pillars and artificial supports, thereby providing support to the mine roof. The overburden load, transferred through pillars and other supports, applies tremendous stress to the floor. Soil mechanics theories provide solutions for foundation design problems that apply to the mine floor. Based on foundation theory, vertical load on pillars causes high shear stress zones in the floor. If the floor is relatively weak, it may fail and dislocate upward into the mine opening. Strong roof strata that do not readily fail transmit most of the overburden load through pillars to the floor. Heaving may result, depending on the thickness and physical properties of the floor

Jan 1, 1986

By Paul Eimon

In the world of minerals exploration, computer-oriented data storage and retrieval methods are being talked about, studied and researched. The goal is to facilitate the recording, collating, indexing, recovery, and analysis of mineral deposit-prospect data. A survey has been made of the various report forms, suggested outlines, and computer coding forms that are currently used in mineral exploration to index and/or describe mineral deposits and prospects. These forms have a number of common characteristics: location, commodities, type of deposit, host rock, etc. Such basic mineral deposit-prospect "data units" are part of most exploration programs. "Data units" may be comprehensive bound published descriptions of mines or mining districts or 3x5 file cards or elaborate computer coding forms being developed in Canada. Initial attempts to develop computer-oriented information systems have run into the same roadblock: the lack of a body of organized, processible data describing the basic qualities of mineral deposits and prospects. To solve this problem, international committees are considering coding forms, world-wide semantics, and rules or standards for data collection and description. It appears that mistrust and lack of understanding of the computer; fear of loss of proprietary information; and disagreements over terminology are distorting the picture of what has to be done if the mining industry is to grow into more meaningful information systems for mineral exploration.

Jan 1, 1969

By N. Prenn

"INTRODUCTION The 2014 SME Guide for Reporting Exploration Results, Mineral Resources, and Mineral Reserves (the SME Guide) has been adopted by the Society for Mining, Metallurgy, and Exploration, Inc. (SME). The SME Guide is recommended as a minimum standard and a basis for developing industry best practices in the classification of Mineral Resources and Mineral Reserves for public and private purposes. The Guide is therefore strongly recommended to be used by members of this organization. The SME Guide was updated in 2014 to include CRIRSCO (Committee for Mineral Reserve International Standards) core definitions, and it is envisioned that the U. S. Securities and Exchange Commission (SEC) will adopt the SME Guide in 2016. However, as of the end of 2015, the SEC Industry Guide 7 remains the standard for the U.S. reporting of Mineral Reserves. This paper will cover the classification of Mineral Resources and Reserves, a discussion of Modifying Factors, and the classification definitions and guidelines. The definitions and guidelines contained in this report are from the SME Guide. FRAMEWORK FOR MINERAL RESOURCE AND MINERAL RESERVE CLASSIFICATION Figure 1 illustrates the classification of Mineral Resources and Mineral Reserves using the Guide. Mineral Resources are divided into three classifications of Inferred, Indicated, or Measured while Mineral Reserves include Probable and Proven classifications. These classifications reflect improved knowledge and confidence of the deposit from the top of the figure to the bottom. In other terms, the deposit risk also decreases from top to bottom.The relationships in Figure 1 reflect different levels of geoscientific knowledge and different degrees of technical and economic evaluation. Mineral Resources can be estimated on the basis of geoscientific information with input from other disciplines to establish reasonable prospects for eventual economic extraction. It was not too many years ago that the classification of a Mineral Resource was based on the evaluation of a limited set of factors that included spatial drill hole and grade distribution (kriging variance, as example), distance to the closest hole, and number of samples used to estimate a block grade. These are still important considerations, but classification following the Guide must also take into account sample integrity, sample QAQC, database integrity and completeness, geological understanding, and geological and grade or quality continuity. In addition, a general consideration of the Modifying Factors, to establish reasonable prospects for eventual economic extraction, adds complexity to the classification."

Jan 1, 2016

By Raymond L. Jones

With the inauguration of the open pit operation in Bagdad, plans were formulated for a large scale leaching operation. Dump stockpiling was started almost immediately, but actual production was not initiated until the spring of 1961. Like all neophytes, we started something about which, on a commercial scale, we knew next to nothing, either dump preparation or leach procedure, and as a consequence, we are still paying the piper. True, we had been through an extensive laboratory pilot program, but it soon became apparent that there was considerably more to increasing solution volumes than simple multiplication. Had we initially possessed our present acumen, the Cyprus Bagdad plant could be operated more efficiently and at a better profit. During the past several years, the art of dump leaching of copper has improved in many ways, primarily because of the application of scientific principles gleaned from general mining practice. Rigid pH control and the use of atomic absorption techniques for rapid," accurate assaying have probably played a leading role in this respect, although we cannot overlook the other sophisticated electronic controls lending improvement to acid addition and pumping, better piping materials, and lastly, the more efficient use of our pregnant liquors. Thin too, the years of experience have given us a greater understanding of dump behavior in general; and, we can, to a greater extent, measure, predict, and avoid some of the idiosyncrasies inherent in every dump. However, it is my firm belief that we will still be confronted with unexplainable dump behavior as long as we are involved in leaching. We have found our dump to be a wonderful money bank, but one that is capable of yielding a wildly fluctuating profit.

Jan 1, 1975

By E. A. Rychkun

It is essential for a. mining company to determine an optimal mining strategy which will maximize the return on investment. In the case of Placer Development Ltd., the Lerch-Grossman three-dimensional optimization technique has been implemented on a digital computer to assist in the determination of such a strategy. It is the purpose of this chapter to explain and illustrate the methodology of the Placer Development Ltd. computer system with emphasis on the feasibility phase of a mine's development. In the Placer Development Ltd. strategy determination process, it is essential that certain objectives be considered: 1) There must be some means of constructing a realistic computer model of an ore body which gives a significant weight to geological constraints. 2) Data must be accurate and quantifiable. 3) Computer solutions must be unique, i.e., approximation or iteration methods of determining optimal solutions are undesirable. A method must be used which, when given fixed parameters and data, yields a mathematically sound unique solution. The following material is a presentation of how these objectives have been implemented. The flow of this outline will be from the general to the specific, with an example application.

Jan 1, 1979

By J. A. Murray

Maintaining satisfactory air quality in electro-winning tankhouses has been problematic and costly, particularly as plant operating current densities have increased. Conventional approaches, including the use of beads, hollow spheres, surfactants and coalescer devices, have not proved completely effective, requiring that powerful ventilation systems be installed. As workplace and environmental regulations become more stringent, containment of the acid mist at its source is more attractive. An electrode cap system based on this approach has been developed and tested in two commercial copper electrowinning tankhouses. The design, development, installation and cost of the new electrode cap system are described.

Jan 1, 1996

By E. Varouchakis

Spartan Spatial Random Fields (SSRF?s) provide a new geostatistical framework (Hristopulos, 2003) with applications targeting environmental risk assessment and natural resources estimation. SSRF?s have the ability to incorporate constraints based on physical laws in the statistical description and have proved to be computationally fast in the analysis of synthetic data sets. This paper presents an application of a specific SSRF model and a new local-error spatial estimator (Hristopulos, 2005) in the mapping of environmental pollutants using a real data set. A detailed comparison of the local SSRF estimator with a classical kriging method is presented. It is shown that the SSRF approach provides a competitive alternative for spatial estimation.

Jan 1, 2005

By Corale L. Brierley

The depressed economic condition resulting from normal cyclic behavior, a more fundamental structural alteration, or both, is a mandate for change within the mining industry. Although several strategies for change have been proposed, the option of applying high technology processes to this smokestack industry offers the greatest opportunity for regaining global competitiveness and a new vitality. Research and development to secure new technologies require a corporate commitment for substantive change, a tech¬nologically enlightened management, a well¬funded and stable science and engineering effort, and a dedicated and motivated technical team--features in short supply in the mining industry today. However, an alternative to in-house development of frontier technologies is available to this beleagured industry through entrepreneurial, high-tech companies. These entities, with their dedicated focus toward product development, motivated and streamlined teams, high productivity and efficiency, and low costs offer a unique opportunity for large corporations to obtain high-tech products and services. These commodities are available through traditional commercial channels and an array of creative business arrangements. The latter offers notable benefits to large companies including windows on frontier technologies and mitigation of risk. Likewise, entrepreneurial companies profit through manufacturing and marketing relationships and an expanded financial base.

Jan 1, 1985

By Christopher Mark

Area wide pillar failures, or “squeezes,” were once fairly common in underground coal mines. While rare today, they do occur. This paper describes seven case histories that were investigated by MSHA Technical Support. They occurred across the range of US coalfields, in both longwall and room-and-pillar mines, and involved development mining, pillar recovery, longwall panel extraction, and multiple seam interactions. Significant lessons from each are discussed.

Jun 25, 2024