Search Documents

By B. K. Parekh, R. H. Mehta

Handling of fine coal is an importance issue for coal as well as the utility industry. Reconstitution in form of pellet or briquet would be desirable if it could be done economically. This paper evaluates the effectiveness of three binders e.g., asphalt- emulsion, corn starch and Brewex, in forming pellets of ultra-fine clean coal. It was found that asphalt emulsion and corn starch were not effective binders for ultra-fine clean coal, however, Brewex provided excellent quality of pellets, which exceeded all the minimum quasi requirements of coal pellets. INTRODUCTION Advanced coal preparation techniques (physical or chemical) are designed to process ultra-fine (minus 200 mesh or 74 pm) coal. The average particle size of the clean coal product is about 25 pm. Currently available dewatering techniques are effective in providing a 25 to 30 percent moisture product of this size coal slurry (Parekh et al. 1989). Handling and utilization of this dewatered ultra-fine size coal is difficult. Reconstitution, which includes pelletization, briquetting, extrusion, etc., of the dewatered coal product provides an ideal answer to handling and transportation problems. However, reconstitution of fines in the coal industry has not been successful due to various reasons. The most important criterion for its unsuccessful application in the coal industry is the cost of the binder (Capes et al. 1965). Various methods of reconstitution, such as briquetting, disk pelletization, extrusion pelletization and roller and die-pelletization, have been tested for fine coal agglomeration (Conkle et al., 1991) (Richards, 1990). Conkle et al., (1992) have provided a detail analysis of each technique in terms of moisture and operating cost requirements. According to Conkle, briquetting requires a product containing very low moisture, whereas pelletization can be done with coal containing up to 30 percent moisture. Currently available dewatering technique provides about 25 percent moisture product, thus, pelletization appears to be an ideal route for reconstitution. In this paper, results are presented on the comparison of three different binders i.e., asphalt-emulsion, corn starch and Brewers condensed solids (BCS or Brewex), for fine coal pelletization.

Jan 1, 1995

By Cloyd D. McDowell

The Federal coal Mine Health and Safety Act of 1969 has been criticized by those who say it goes too far in controlling the activity of private enterprise and by those who say it does not go far enough in eliminating fatalities and accidents in an accident prone industry. Possibly a better evaluation of this legislation lies somewhere in between. From the viewpoint of the coal industry it can be said that through the efforts of those engaged in mining, both the operator and the miner, the year 1969 marked a record year in mine safety with only 190 fatalities and a frequency of 0.84 per million man hours exposure. This outstanding achievement compared to any previous was the result of a determined effort on the part of a concerned industry to improve its reputation as being the most hazardous industry in the nation. After the effective date of the Act, March 31, 1970, the Bureau of Mines assumed complete control of all safety and health activities of the mining industry. Unfortunately, there was no improvement in the safety record of underground mines in 1970 with the total of 255 fatal injuries and a frequency of 1.04 for the year. The number of fatalities declined to 177 in 1971 but the number of underground coal mines had declined from 5,955 to 2,268 during the two year period. Meanwhile, surface mined coal increased from about 38% of total production in 1969 to over 50% in 1971, keeping the annual production of coal at a normal level but involving fewer men.

Jan 1, 1973

By Roy M. Fleming

During the decade of the 1970's, a new emphasis was placed on assuring a safe and healthful workplace for all American workers. Much of the basis for this national effort was federal legislation: the Occupational Safety and Health Act of 1970 and the Federal Mine Safety and Health Act of 1977 (amended from the 1969 Coal Mine Act). One of the agencies involved in this protection effort is the National Institute for Occupational Safety and Health (NIOSH) of the Centers for Disease Control (CDC) in the Department of Health and Human Services (DHHS). In fulfilling its mandates under the 1970 and 1977 Acts, NIOSH conducts research, experiments, and demonstrations to support and stimulate advancements in health and safety practices. Priorities for NIOSH research are established primarily through congressional mandates, requests from the Department of Labor, needs as defined by NIOSH researchers, and surveillance information. Emphasis is placed on research in the areas of toxicology, industrial hygiene, physical and chemical sciences, physiology, ergonomics, engineering, psychology (behavior and motivation), and epidemiology (industry-wide studies). The framework of the current Institute program to identify, evaluate, and control occupational hazards includes activities in surveillance, research, evaluation, and training. These activities are planned and evaluated through a system that coordinates the efforts of eight research and scientific divisions. Each division develops projects to address program areas that have been identified by NIOSH management as having highest priority. In surveillance programs, the objectives are to identify substances and agents found in a representative sample of workplaces and to collect and evaluate information on rates of disease and injury in occupational groups. Information is also collected on occupational safety and health programs implemented by industry. Estimates of worker exposures and the potential for adverse health effects are considered in setting priorities for further investigations. A related activity, which also serves to provide technical assistance to industry, is NIOSH's Health Hazard Evaluation program. On-site investigations of workplaces are made in response to worker, employer, or government agency requests. Both industrial hygiene and medical examinations are conducted, and the results contribute to identifying new problems and evaluating their significance which may have public health implications beyond the particular worksites that are investigated. Field and laboratory research projects are performed to meet several objectives: - Characterize the working environment by evaluating current and past exposure levels for workers who are included in epidemiological or medical investigations. - Develop epidemiological information to define the association between the substance or agent under investigation and the acute and chronic health effects on workers. - Determine through animal studies the parameters of an association between exposure and effect. - Investigate the etiology of disease. - Develop sampling and analytical instruments and techniques and demonstrate their application for measuring toxic materials in the workplace. - Formulate sampling strategies that will accurately and precisely indicate exposure levels. - Develop medical procedures to prevent disease and to detect the presence of disease and early indicators of disease. - Assess the technology for control of exposures, including engineering and administrative techniques, personal protective equipment, and work practices. Presently, the research program is focused on reproductive effects, neurotoxic effects, injury/trauma, lung disorders, cutaneous disorders, cardiovascular disorders, cancer, stress-related disorders, effects of physical agents, digestive disorders, and renal and other organic disorders. In studying these issues, priorities are determined by the seriousness of possible adverse health effects resulting from occupational exposures, the feasibility of studying existing records or obtaining new data, and the size of the population which is potentially affected. Where there is low level of suspicion concerning adverse health effects or where an occupational disease occurs in a variety of industrial environments, investigations are limited to gross analyses of health effects such as review of mortality patterns. In such studies, the industrial populations selected are those for which existing data resources can be utilized. Such data consists of records of occupational exposures or health status which have been maintained by the employer, the union, or Government agencies. Where a review of the available information suggests that serious health hazards exist and the existing data resources are inadequate for quantifying the relationship between the specific biological response and type and degree of exposure, prospective studies are initiated. Information derived from such research is essential for the development of sound criteria for control of industrial exposures to noxious agents. Other input to the criteria documentation process comes from searching and evaluating the literature. Criteria documents contain the recommendation of an environmental limit where information is available to support it, as well as the recommendation of work practice controls, medical evaluation, information for workers to recognize and avoid the hazard, and identification of specific research gaps. In some cases, during the criteria document preparation, gaps in knowledge are found which necessitate further research before an occupational standard can be recommended.

Jan 1, 1981

By Harry M. Castrantas, James L. Manganaro, Craig W. Rautiola, James Carmichael

Caro's acid (peroxymonosulfuric acid) was successfully field tested as a cyanide detoxification agent at a North American gold mine. An on-site FMC generator injected Caro's acid into a mill tailings slurry sump. The WAD cN-(weakly acid dissociable plus free cN-) was reduced from 40-108 ppm to below the target level of 20 ppm using a 1/1 mole ratio of CA (Caro's acid) /CN-. At an inlet CA/CN-mole ratio of 1.8/1, WAD CN­concentrations as low as 4 ppm cN-were achieved. Raw material costs for the cyanide detoxification were cut by 60% compared to using hydrogen peroxide (H202) alone. Detoxification time with Caro's acid was much faster compared to H202. This resulted in completion of detoxification before the treated slurry reached the tailings pond thereby substantially reducing the probability of wildlife fatalities.

Jan 1, 1993

By F. L. Wilke

A model is presented to minimize the winning costs per shift within the different sections of a potassium mine by liner programming and to simulate the other areas to get all costs in order to comp re different production strategies. he model is based on a a given total layout of the underground mining which is considered to be fix during the planning period. Room-and-pillar mining is assumed to be used. Potassium extraction is done by drilling and blasting. Transportation of the raw material to sectional crushers is done by scoop-trams where it is crushed to coarse-grains which allow further transportation by conveyor belts to the hoisting shaft or to a bunker. When production is stopped, the continuously working factory is supplied by means of this bunker. Starting from a desired composition of the raw material the model has to keep the given total. demand of raw material per shift, to minimize the winning costs, to keep the capacity constraints of the equipment and to determine the planned output of production of the sections per shift. Costs of the areas which follow the extractions are added to extraction costs in order to allow a comparision of costs of several alternatives of production. Optimization in extraction and assignment of scoop-trams to sections is done by linear programming. The other areas of the mine are treated by simulation. The model output is a schedule of the calculated costs broken down into costs of processes, equipment, and kinds of costs. This proceeding enables to compare different ways of production.

Jan 1, 1979

By J. Starwood

Post-super-cycle mining executives must exploit every aspect of the value chain to deliver continued value to stakeholders. Integrating enterprise-wide information technology with value-chain-wide operational technology, known as IT-OT integration, is essential to extracting optimal results from the value chain. Mining companies trail other industries with respect to IT-OT integration across the value chain. Manual data consolidation and value chain optimization using spreadsheets and human intelligence are widespread practices within the industry. Increasing automation with smart devices and controllers means the volume and velocity of data will soon increase beyond human abilities. Enterprise Architecture provides a method for aligning information technology with the business operating model to successfully implement IT-OT integration. A Value Realization Framework (VRF) provides a means for predictable traceable value realization from IT investments and assets. With these principles, frameworks, models, methods, and techniques, mining organizations can accomplish IT-OT integration that provides their executives with a strategic value-chain-aligned platform for sustained value realization over the long term.

Feb 23, 2014

By Richard E. Hucko

The U.S. Department of Energy (DOE) Coal Preparation Program focuses on providing the technical and process-development basis that can be utilized to produce environmentally acceptable clean-coal feedstocks for use as market conditions permit. A major objective of the Coal Preparation Program is the development of physical coal-cleaning technologies capable of significant removal of mineral matter and pyritic sulfur at high energy recovery levels.

Jan 1, 1989

By H. Gerry Stephenson, Devin Castendyk

"One of the most important environmental issues associated with contemporary openpit mining is the closure of mine pit lakes, and the perpetual legacy these lakes can potentially generate. Ideally, successful pit lake closure includes the following:• The water quality within the pit lake, plus surface water and ground water discharging from the pit lake, meets premining or other acceptable water quality conditions of the receiving environment. • The termination of all active treatment processes.• The return of the pit lake to the government for long-term care and maintenance.• The release of the mining company from all future liabilities associated with the pit lake.• The return of the environmental bond to the mining company.• The reuse of the pit lake for some post-closure, beneficial purpose.The achievement of these goals is known as walk away pit lake closure.Peer-reviewed publications of successful walk away, pit lake closure provide mining companies with the ability to address public concerns regarding the safety of pit lakes which commonly occur during the permitting, operations, and closure phases of mining. To date, most published work on walk away, pit lake closure work has occurred in the coal mining sector in Germany and Australia (McCullough et al., 2009; Jones and McCullough, 2011; Kumar et al., 2013; Schultz et al., 2013). In North America, examples of walk away, pit lake closure are not widely discussed in the literature despite there being excellent examples from the coal mining sector in Alberta, Canada (e.g. Pleasure Island, Black Diamond, East Pit, Sphynx, Robb, Lovette, Siltstone and Sterling), and from the iron mining sector in Minnesota in the United States (e.g. Portsmouth Lake, see MNDNR, 2018). Although seldom included in discussions of pit lakes from the metal and coal mining sectors, the aggregate and fabricated-stone mining sectors also produce pit lakes, and there are numerous examples throughout North America where these pit lakes have been successfully closed and transformed into post-mining resources (Vandenberg, 2018; Crossman, 2019). The difficulty of finding these good examples in the literature makes it challenging for companies to respond to public and regulatory questions regarding pit lake closure and reuse. As such, there is a pressing need to document the motivations and approaches used in examples of successful, walk away, pit lake closure in North America so that the mining industry, at large, can learn from these examples and can better address public concerns."

Aug 1, 2019

By P. J. Mackey

A whole new group of non-ferrous pyrometallurgical processes with the ability to utilize tonnage oxygen and capture sulphur dioxide were developed and commercialized over the period 1940s–1980s. Many of these earlier process developments were undertaken with limited knowledge of the process chemistry and influence of key process variables; in many cases, piloting helped provide much new physico-chemical data, but gaps remained. The second generation versions of these technologies of today provide all the primary copper, nickel and lead produced worldwide by pyro-metallurgical smelting. Further, process development has continued and a new generation of copper and lead smelting technologies have also been developed in China since the 1990s. The older reverberatory and blast furnaces have been progressively replaced by the newer technologies—a good example being the introduction in 1992 of the copper IsaSmelt technology at the Mt. Isa smelter in Australia where the former fluid bed roaster and reverberatory furnaces were replaced by a single new smelting unit, together with an acid plant for sulphur dioxide collection. The development of these new technologies was made possible by investment in fundamental and applied research. The lesson for the future is, in order to sustain these improvements, continued investment in research and development capability is required—to do otherwise is to risk obsolescence and lack of competiveness in the world market. Dr. Peter Hayes at The University of Queensland is one of the many researchers and process engineers who have contributed to the fundamental understanding of metallurgical processes over this period of rapid change in technologies. The present paper briefly outlines some of the many contributions Peter Hayes has made to the understanding of kinetics, mechanisms and phase equilibria in metallurgical systems, and metallurgical process development.

By N. Bat, N. Sarantsatsral

Blasthole sampling practices were investigated at the Erdenet copper and molybdenum mine in Mongolia to address grade reconciliation issues. The goal of the study was to determine if the particle size distribution (PSD) of blasthole cuttings was accurately reflected in the samples. The study additionally examined if the measured grade was related to the particle size of samples. Using a sector sampler specifically designed to collect samples for the study, six large samples were collected from three blocks following a specialized protocol. Each sample was split into nine size fractions, ranging from larger than 12 mm to smaller than 63 µm. Copper and molybdenum grades were determined for each of the size fractions. For comparison, nine samples were collected from the same blocks following the standard mine sampling protocol. These samples were also split into the same nine size fractions. As with the other samples, grades were determined for each of the size fractions. The results showed that the PSD in the samples collected following the standard operating procedure varied significantly from sample to sample. This variation was much lower for the samples collected following the specialized protocol. Loss of fines was also indicated in the standard mine sampling process. These observations suggest that the standard sampling protocol did not consistently capture the PSD. The copper and molybdenum grades increased as particle size decreased, regardless of the sampling protocol used. This observation underscores the importance of the PSD of a sample being representative of the true PSD. Given the low number of samples in the study, it is not a strong conclusion that the standard sampling protocol captures the PSD inconsistently. However, it could be taken as a caution. On the other hand, the grade versus PSD relationship is more certain, given that it was observed regardless of the sampling method used.

Feb 1, 2017

By James D. Cooper

Technologic advances in materials utilization during the past two decades have brought is a long way toward the point where we can make the products we need from the materials we have readily available. Notable examples are the synthesis of diamond, zeolites, quartz crystal, mullite, and mica, and the development of phosphate bonded tale. Two of these--zeolites and mullite--involve the use of clays. There is little reason to doubt that equally important advances will be realized in the next decade, and that clays will play an important role in the developing materials technology. Indeed, the stage is already set for many of them. This discussion is concerned primarily with the high quality, relatively high priced clays, kaolin, bentonite, fuller's earth and ball clay. The first three have enjoyed demand growth rates over the past two decades which on the average exceeded the growth rate for the economy as a whole. There are indications that demand for ball clay will be growing at a faster rate in the future.

Jan 1, 1970

By John D. Hanifin, C. Kevin Moon, Eric C. Wang

Value Engineering on Connecticut DOT’s Walk Bridge selected the trenchless option for utility relocation to address the channel crossing’s environmental concerns. The design and construction considerations of the twin micro-tunnel drives and associated shafts are presented. Key challenges included vertical alignment selection to achieve minimum one-tunnel diameter stable cover within thin glacial till underlying extremely soft clay, limited choice of pipe and joint materials meeting stringent non-metallic conduit requirements, thermal grout backfill application, and the close proximity of temporary trestle piles. Mitigation measures were developed for potential point loading pipe damage from remnant boulder fragments in the annular space.

Dec 1, 2022

By Adam Levy, Thomas Novak, Sampurna Arya, Joseph Sottile, Kozo Saito

The use of a woven wire-mesh screen as part of a flooded-bed dust-scrubbing system is popular in the underground coal mining industry. It is used in combination with a demister (mist eliminator) to remove dust from the dust-laden air. A study was conducted to measure the pressure drop across a flooded-bed, wire-mesh screen at different airflow rates in one-phase (dry) and two-phase (wet) conditions. Two empirical relationships between pressure drop and air velocity were developed for dry and wet conditions, respectively. In both cases, the form of the empirical relationships was found to be similar to relationships given by Sabri Ergun for high velocity, non-Darcy, single- and multi-phase flow through porous media. The experiments were repeated on a reduced-scale model of the wire-mesh screen, and the pressure-velocity relationships obtained from the full-scale prototype experiments were tested. The test results show validation of the full-scale empirical formulae on the small-scale model with an insignificant variation. This paper presents the empirical equations for pressure drop across the wire-mesh screen in dry and wet conditions. Researchers can use these equations as a tool to predict total pressure drops for wire-mesh screens of different scale sizes.

By Greg Watson, Dennis Ofiara

"TBMs have been used in mining in decades past, but their use has been limited and sporadic, due to both perceived and actual application difficulties. With new technology and mounting success stories, this is changing. For both coal and metals mining, deep ore bodies require long access tunnels, and an efficient and economical method of reaching those deposits. Today, mining engineers are considering TBMs as part of the overall mine development plan. Planned TBM mine drifts are not only longer, but have more complicated trajectories. Mine development TBMs will have to cope with varying geology, potential for high water inflows, steep gradients, and high temperatures. TBM systems are being planned to cope with such difficulties. TBM systems will be considered and increasingly deployed for mine development, even if commodity prices remain low. TBMs can satisfy the need for increased productivity, better life of mine infrastructure, and safety. Effective conveyor systems are essential to support TBM operation in many mining applications. Many mine development tunnels are slopes, driven down at the steepest practical gradient to reach the deep ore body. Conveyors are often the only safe and effective way to haul the TBM muck form such tunnels. This paper will review the historical use of TBMs in mining, and will discuss the 2015 status of TBMs and conveyor systems in mining, and the special requirements and adaptable features needed in order to make efficient TBMs a reality in mines worldwide.HISTORICAL USE OF TBMS IN MINING APPLICATIONS The first successful hard rock TBM was invented in 1954. Over the next decades, TBMs have been used in many mining applications: Mine access drifts in several Spanish mines •,White Pine Copper Mine, USA •,Selby Coal mine drift, UK •,Coal slopes in Appalachia, USA •,German coal mines accdess drifts, several mines •,Magma Copper San Manuel, USA •,Cape Bretton Undersea Coal Slopes, Canada •,Stillwater Mines, USA"

Jan 1, 2016

By P. M. Lin, P. Tsang, S. S. Peng

This paper presents an overall stabilization method to eliminate the potential of reoccurrence of subsidence over abandoned mine lands (AML). The method considers column grouting at specific locations, including the destressed and stress concentration zones, instead of grouting around and beneath damaged structures. The latter method is currently commonly used for AML subsidence abatement. The finite element method (FEM) can be used to calculate stress distribution in the strata before and after grouting. A grouting pattern is generated that includes the location and number of grouting holes. Stress concentration can be reduced or eliminated. A comparative analysis, including the number of grouting holes, area of grouting influence, stress level and potential of subsidence reoccurrence, is also presented.

Jan 1, 1993

By B. Das

Most coals are susceptible to spontaneous heating which in turn creates problem to mining, storage and transportation of coal. It is impossible in actual practice o eliminate spontaneous heating but spontaneous combustion can effecively be controlled through a clear understanding of its mechanism and the factors affecting it. There are altogether six stages in the process of spontaneous combustion. This includes the water adsorption stage and six oxidation stages: chemi-sorption (upto 70°C), decomposition of peroxygens (70°C-150°C), oxy-coal formation (150°C-230°C), combustion initiation (230°C) and active combustion (> 230°C). Heat is produced in all these stages. On the other hand heat is also dissipated so that some equilibrium temperature is reached. If this temperature exceeds a certain critical value (generally about 70°C), coal oxidation may advance to spontaneous combustion. The major factors influencing spontaneous combustion of coal are: coal rank, maceral composition,, water, mineral matter, joints and fissures, seam depth and thickness, mine Layout, method of ventilation, etc. Susceptibility is high for low rank coals and generally decreases with increase in rank. Of the macerals, the exinites are generally most susceptible, the inertinites least and the vitrinites somewhere in between. Water plays a major role on the spontaneous heating of coal, assisting in someways and inhibiting in other. Unrecovered coal in the gob (generally in thick seams) is a major source of fire hazards and this is specially important in shallow mine. Proper design of mine ventilation system can substantially reduce the risk of mine fire. Panel layout and load transfer can affect the development of induced cracks which in turn influence spontaneous heating. Finally, the difference between the spontaneous heating of coal in a seam and that in storage or transportation is mainly due to the change in moistured content, air circulation through the coal and coal fragmentation. These aspects have been analyzed in this paper with a view o reducing the risk of spontaneous combustion.

Jan 1, 1986

By M. M. Rajkovich, J. J. Zaluski, S. J. Gardner

The telephone rings at 3:20 a.m. and an exasperated voice on the other end says, “There’s been a mine explosion at Mine No. 5 and we have not heard from three units of men!” Twenty-three minutes later, the phone rings again and another panicked voice says, “There’s something wrong at the slurry impoundment, the pool level has just dropped five feet and we’re trying to figure out what’s wrong!” Thirty minutes later, the mobile phone rings and an excited security guard says, “We have reports of thick black water running down both the right fork and left fork of Straight Creek and both seem to be rising in the banks!” As if this isn’t enough excitement, the mobile phone rings again and a stressed company official says, “I just heard a report that black slurry is running out of the portals of XYZ Company No. 2 Mine, which is adjacent to our No. 5 Mine!” Is this all some kind of dream or nightmare? More importantly, however, if this could happen, what on earth do you do? Although we all like to think that “It can’t happen to me,” we all must admit that mine explosions do happen, slurry impoundments can rupture and creeks can flood with black water causing damage to others, including competitors. Your response must be quick, cool-headed, calculated and effective. This paper will examine the issues, concerns and ramifications of this hypothetical “disaster” and then present a systematic crisis management response. While each situation is different, there are general guidelines for forming an effective plan of action.

Jan 1, 2003

By W. E. Anderson

As part of a larger study to identify factors influencing the practical operating life of wire rope used on large draglines in surface coal mining, field trips to operating surface coal mines were made during late 1975. Wire rope performance information was obtained from personnel at thirteen mine sites west of the Appalachians. Seventeen pieces of equipment, utilizing buckets ranging from 30-to 220-cubic-yard capacity, were documented. We have judged that U.S. surface coal mining draglines, 30 yards and larger, can be represented as 120 machines having 60-cubic-yard buckets, moving 1.8 x 10 yards of overburden during 6,650 hours of productive availability per year. Based on our limited field study, we have calculated that downtime resulting from rope-related causes averages 105.6 hours per year for each (typical 60-yard) dragline. The total lost production from this source alone is thereby estimated at about 25 x 10 yards annually. Although study findings did not reveal anything about dragline rope life that wasn't known or practiced by one operator or another, most operators could expect improved rope life by periodic review of their practices and by adopting or adapting one or more life-improvement measures employed at other sites. Since rope productivity was found to vary by about five to one, among the sites studied, we believe considerably improved average performance is possible. As little as ten percent overall improvement would mean increased national productivity exceeding two million yards of solid overburden removal, and associated savings in rope costs alone of some two million dollars annually, not to mention any reduction of labor-related expenses. This report outlines preliminary findings which may prove useful to many operators in extending wire rope life, thereby lowering expenses and increasing surface coal mining productivity. Some of these modifications or adjustments in maintenance/operating practices would not require capital investment. We did not find anyone who had tried cost reductions by using presocketed dump

Jan 1, 1977

By Harold Gibson

The mechanisms leading to the impact of airborne dust particles onto bluff flow obstacles have been extensively reported [1] and widely applied in dust measuring instruments (e.g., impactors) and in dust collecting devices (e.g., filters and scrubbers). If the human head is regarded as a bluff body, particles from dusty flowing air can impact onto the face by virtue of those mechanisms. While a great deal has been researched and written on the nuisance caused to human beings by the entry of dust particles into the body by inhalation through the nose and mouth, there appears to be nothing reported in the scientific literature about the irritation which can be caused by the impact of dust onto the face. And yet there is sufficient evidence to suggest that in certain working environments and under certain conditions, the problem is indeed a real (albeit subjective) one. In the coal mining industry, underground workers are exposed to conditions, involving dust-creating production and handling processes on the one hand and high ventilation rates demanded by the gassy nature of the environment on the other, in which the problem can exist. At the coal face, for example, the movement of powered roof supports ("chocks") can release bursts of dust formed by the crushing action of the supports, which in turn is entrained into the moving air and impacts onto the faces of miners working just downstream. The dust in question contains a large proportion of coarse particles which, while still fine enough to remain airborne for appreciable distances downstream of the point of release, are coarse enough to produce sen¬sation on impact with the skin. Adverse subjective response of workers to such irritation could damage morale and productivity. We have performed laboratory and field experiments to investigate the psychophysical and physiological responses of human subjects to dust impacting onto the face and into the eyes. Since this appears to be the first systematic investigation into these questions, the aim has been to construct a useful scientific framework from which to allow characterisation of the problem of such "fly-dust", and, ultimately, the development of methods for monitoring and controlling it. The main results of our research are given here; the theoretical and experimental details will be presented at greater length elsewhere.

Jan 1, 1980

By Wen H. Su

Extensive investigation has been conducted to determine the causes of a series of roof falls occurring in a room-and-pillar working located in southern West Virginia. Underground observation, along with laboratory testings and finite element analyses were conducted to search for possible mechanisms for the roof falls. Results of the investigation have led to a better understanding of the mechanisms involved in the roof falls. Necessary modifications of mine layout and roof support plan are proposed for improving safety and profitability at the mine.

Jan 1, 1984