Search Documents

By A. Noble

Linear circuit analysis (LCA) is a fundamental tool which has been used to evaluate mineral separation circuits during the preliminary design phase. Traditionally, the LCA methodology uses the analytic circuit solution to determine the relative slope of the circuit?s partition curve. This value is then used as an indicative performance measure suitable for the comparison and ranking of alternative circuit configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. In most mineral systems, this material represents a small portion of the initial feed (due to liberation) as well as a small portion of the revenue potential (due to the incremental value). Respecting these limitations, the authors have developed new separation performance indicators which may be derived from the analytical circuit solution and used in LCA problems. These indicators inherently reflect the separation potential of pure material, providing a better indication of lost revenue due to misplaced material. The complete methodology has been integrated with prior software to produce the Heuristic Optimizer for Resource Separation Economics (HORSE).

Feb 23, 2014

By Leonardo Rosas Sánchez, Darío Ángel Bulla

"The two track road sector between Cisneros-Loboguerrero (having a length of 14 km and 11 short unidirectional tunnels) is a new highway still on construction located along the existing Highway Buga – Buenaventura (Colombia). Due to the steep topography, difficult geological/geotechnical conditions, the traditional portal construction approach was impossible to be implemented in eleven (11) of the twenty two (22) portals. In this specific project, the skewed portal approach was developed as the optimal and more effective solution. The construction time and costs of portals were reduced in 21 months and 75%, respectively. At the same time, the natural equilibrium of the slopes was maintained, thus, facilitating adequate safety factors along the useful life of the project. This document pretends to show a detailed design experience (and the construction of the entry portal of tunnel 11 (left)). INTRODUCTION The Cisneros-Loboguerrero project is a 14 km length dual lane highway, connecting productive zones with the Pacific Ocean along the current Bogota-Buenaventura highway as shown in Figure 1. The project is located at the northern side of the Dagua River Valley. The preliminary design suggested constructing portals under challenging topographical conditions, i.e., slope cuts having heights between 50 to 100 m (some having slopes > 100%) requiring complex developments and having very high risks.The entry portal of tunnel 11 (left) was the first portal successfully built by implementing the skewed portal approach. Later, this approach was used as a model for the construction of the other ten (10) portal having similar topographic and geotechnical conditions. The development of this new alternative provided a considerable reduction on the construction time of portals, thus relieving a critical path in this project."

Jan 1, 2016

By C. J. Pritchard, R. D. Jacksha, K. V. Raj, C. B. Sunderman

In underground metal/nonmetal mines, repeated localized short-term exposure to high levels of airborne contaminants can become a serious health issue. Currently, there are no common mechanisms to control or mitigate these short-term high exposures to contaminants. To improve miners’ health and safety, the U.S. National Institute for Occupational Safety and Health’s Spokane Mining Research Division (SMRD) is developing a smart monitoring and control (SMAC) system for the real-time monitoring of mine air quality, with integrated countermeasures to reduce high concentrations of airborne contaminants in localized sections of mines. To develop and test a SMAC system capable of being implemented in an underground mine, SMRD researchers built a test apparatus incorporating a fan, louver, ducting and sensors combined with atmospheric monitoring and control software. This system will institute effective countermeasures to reduce contaminant levels, improving miner safety and health.

Jan 1, 2018

By L. S. Rubin

The efficient and acceptable disposal of fine coal refuse (28MxO) is one of the highest priority problems facing the coal industry today. For many years the established system for the disposal of this fine refuse slurry has been to concentrate the solids in a static thickener and pump the resulting 20-40% solids underflow to lagoons or impoundments. Although this technique has served the coal industry well, increasing environmental concerns and refuse related disasters, such as Buffalo Creek, West Virginia and Aberfan, Wales, Great Britain have resulted in federal and state regulations which now control fine refuse disposal methods. As a consequence of these regulations, the capital costs of constructing, maintaining, and operating regulatory complying impoundments has become in many cases economically unattractive. Areas processing topologies similar to those coal preparation plants of the Appalachians are particularly burdened by these regulations and are consequently turning to alternatives for handling and disposal of their fine coal refuse. The basic requirements of impoundment alternatives as defined by environmental and plant demands are: (1) A relatively solids-free liquid (1000 ppm or less) to serve as plant make-up water in a "closed circuit" system, and (2) a sufficiently dewatered solids product which can be combined with the coarse refuse to form a compactable stable land-fill.

Jan 1, 1978

By H. W. Breathitt

World demand for phosphate rock has increased significantly in the past fifteen years. Prior to the early 1960's, most of the world production was obtained from Florida, North Africa, and Kola. As the 1960's arrived, new mines in North Florida and Eastern North Carolina, as well as expanded production in the Western United States, .increased domestic production. Many new mines overseas have also become significant. This includes countries such as Senegal, Togo, Israel, Spanish Sahara, and Jordan. Limited production, often as by-products, has been noted in South Africa, Brazil, and other countries. In recent years, and even recent months, we have learned of many new areas being considered as potential sources of phosphate rock. This includes Australia, Saudi Arabia, Mexico, Colombia, and Brazil. Many other developing countries have discoveries and are considering their new deposits, often with difficult beneficiation problems, as potential sources of phosphate. These factors all relate to expanded world, population and the demand for more fertilizer products to produce food. In this paper, four areas of the world with different types of phosphate deposits are briefly reviewed to contrast the ore beneficiation problems to Florida procedures--long considered the "standard" of the industry, at least for most of the United States' domestic production. Agrico has three large operating mines in Florida with total production capacity exceeding seven million tons per year. Here, pebble phosphate (+14 mesh material) is produced without the use of flotation, whereas all of the material finer than 14 mesh is subjected to flotation beneficiation to upgrade into high grade concentrates.

Jan 1, 1977

By J. Stowe

"While there has been continual improvement in the models for predicting deposition velocity and pipeline friction losses, the fundamental design philosophy for tailings pipelines has remained the same over the previous three or four decades: design the tailings pipeline to operate in turbulent flow without a deposit on the pipe invert for all expected process conditions. Recent improvements in the understanding of slurry pipeline flows allows for the design of pipelines operating with a deposit on the pipe invert, allowing the system to operate at moderate velocities for high flow rates, optimizing system energy requirements and maximizing pipeline wear life.Tailings pipelines are increasingly operated at higher solids concentrations when there is a greater likelihood the pipeline will operate in laminar flow due to the higher tailings slurry rheology. Historically, slurry pipelines have been operated in turbulent flow. We now know that laminar-flow pipeline operation is possible as there are several operational laminar-flow tailings pipelines. While our understanding of laminar-flow slurry pipelines is not complete, recent research provides guidance on how to approach the design of these pipelines.New sensor technology has led to the development of an instrument that provides reliable indication of bed-deposit height within a pipeline. This technology is particularly helpful in operating pipelines with a deposit and has application in better understanding the operation of laminar-flow pipelines. Failure of tailings pipelines can result in consequent damage to surrounding structures and unacceptable spillage into the environment. Modern pipeline leak detection technology allows operators to better manage this risk by ensuring safe and reliable operation of tailings pipelines.This article provides an overview of the each of the above advances in the design and operation of tailings pipelines.Operating tailings pipelines with a depositTailings pipelines, and slurry pipelines in general, are typically designed to operate without a deposit on the pipeline invert. Meaning, the minimum operating velocity exceeds the turbulent deposition velocity. This approach has been adopted due to concerns regarding potential blockage of a pipeline operating with a deposit."

Jun 1, 2019

By R. A. Lowe

Smectite is a common impurity in the kaolins of Georgia. This impurity is harmful to the low-shear rheology of kaolin slurries in concentrations as low as a few weight percent. The deleterious effect of smectite on the low-shear rheology is due to the swelling of the mineral. Montmorillonite containing clays were treated to precipitate a compact brucite layer {Mg(OH)2} in the interlayer region of the expandable layer silicate mineral. This treatment forms a hydroxy-Mg-montmorillonite with characteristics similar to chlorite. This treatment effectively reduces the swelling capacity of the mineral and improves the rheological properties of kaolin slurries contaminated with smectite impurities.

Jan 1, 1999

By M. P. Meehan

The purpose of this paper is to present the Anamax Instrumentation Department's: responsibilities, organization, preventive maintenance, test facilities, training and applications. The Anamax Mining Company is a general partnership between AMAX Arizona, Inc. (a subsidiary of AMAX INC.) and The Anaconda Company (a subsidiary of Atlantic Richfield). Anamax's product and by-products include: copper, molybdenum, and silver; uranium is to be added as a by-product in early 1980.

Jan 1, 1980

By Yi Luo

Subsurface strata movements and deformations caused by longwall mining operations in underground coal mines could affect many important coal mining activities, such as gob well degasification, ground water protection and multiple seam mining. The stratifications in the overburden have significant influence on the subsurface and surface movements and deformations in the ground subsidence process. An enhanced subsurface subsidence prediction model considering overburden stratifications has been introduced in this paper. In this method, the entire overburden strata are equally divided into a finite number of layers and the percent of the hard rocks in each layer is an additional input. The proven influence function method is applied to predict the subsidence on each of the predefined layers progressively upward using the predicted subsidence on the previous layer as the subsidence cause for the current layer. A computer program is developed to facilitate the calculations. A case demonstration is used to show the applicability of the proposed subsurface subsidence prediction model.

Jan 1, 2012

By Russell Frith

A review of published literature reveals case histories whereby the entire periphery of a coal pillar has “burst” out as a single event during first workings, the associated energy and material release causing significant damage to adjacent roadways and any equipment/infrastructure located within said roadways. Such events are distinct from coal burst events during first workings such as that at the Austar Mine in 2014, or those linked to overburden bumps related to either horizontal stress-driven slip along major faults and/or thick, massive strata units in the overburden or floor of the coal seam.

By Doug Brown

The recent expansion of our cities into hilly areas, particularly on the Pacific Coast, has resulted in damage or destruction of many homes due to geological problems such as landslides, soil creep, erosion, subsidence, or groundwater seepage. In southern California, landslides are the principal cause of damage and attention is focused on them. Landslides have occurred due to the reactivation of old slide masses, or have been caused by grading and increased water, infiltration resulting from development.. Reactivation of a portion of the ancient Portuguese Bend landslide in Palos Verdes, Los Angeles County, affected approximately 150 homes. A common type of new failure' occurs when grading has undercut bedding or other essentially planar surfaces so that they dip unsupported out of slope. Other slides have occurred due to the inherent weakness of the material involved. Preventive measures undertaken to eliminate damage in the southern California area have. included areal geologic mapping programs-in-advance of development, enacting or strengthening grading codes, and requiring extensive studies by consulting geologists and soils engineers both during the design stage and during construction. In the design stage, proposed cuts are frequently flattened, lowered or reorientated. Frequently, due to the high cost of land, they are supported by compacted fill buttresses. As a result of these measures, the geologic environment has a major effect on the feasibility, design, and development of, a very substantial percentage of tracts or individual homes.

Jan 1, 1967

By D. L. Stevens

Following an in-depth scenario and strategic-planning exercise in 1997, Noranda's mine production goal was set at 500 kt/a (550,000 stpy) of both copper and zinc metal in five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in Noranda's program. The following steps were taken: the exploration and business development groups were combined, teams were formed to search for and respond to opportunity; geologists were coached to become more business minded and engineers were coached to become more optimistic; the company went global; clear thresholds were set, marginal properties were farmed out and other properties were fast tracked; reconnaissance exploration was focussed where there was a clear competitive advantage; and Noranda became a "flexible" partner to juniors and seniors. Is it working? A number of successes, near successes and outright failures are discussed. The main result is a much higher rate of opportunity flux, which is essential for success in the mining industry.

Jan 1, 2000

By J. Driscoll

After 30 years of success, Newmont Gold Company has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East Decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East underground at the rate of 700 t/d (770 stpd) for an annual production of over 100,000 ounces. Over 70 underground miners enjoy the estimated 6-year mine life at Carlin East. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By Fang-tu Wei

The purpose of developing this system is to monitor the operating status of the fully mechanized mining system in order to raise it's reliability. The completely mechanized coal mining system is a complex dynamic system, involving many sub-systems. It is the key of the mining process as well as a connected system composed of each working procedure. Any hitch in breaking, loading or transporting will interrupt the mining process. The analyses of the operating data has proved that the reasons causing the interruption of the extracting processes mainly come from the inner of coal face. Hence, after the installation of the MINOS system in England, the delays of belt conveyor sub-system were reduced. But the production increment was not as much as expected.

Jan 1, 1986

By Thomas Van Riper

Newmont Mining Corporation started as one man's investment vehicle. William Boyce Thompson, Newmont's founder, was already a millionaire many times when he incorporated his existing Newmont company in Delaware in 1921. The initial stake in the company was $8 million in capital contributed by Thompson and several close associates. In its infancy the company was truly a holding company. It did not operate or manage any properties. This situation changed drastically over time. By 1939 Newmont was actively mining 12 gold mines in North America. The following year, the first copper mine that Newmont ever managed directly, came into full production in South Africa. The period after World War I1 was a glorious one for Newmont. Plato Malozemoff took the helm of the company, and expanded its operations over the next 30 years into copper in Arizona, oil and gas in the U.S. and the North Sea, into domestic coal and thankfully, into significant gold operations.

Jan 1, 1989

By L. J. Vincze

The program of study of pellet binder materials was begun by the ORF in 1963 to examine various Canadian materials as substitutes for bentonite which is imported in large tonnages (199,270 tons in 1969) from the U.S.A. for Canadian pellet plant operations. Most of the raw bentonite used in Canada originates in Wyoming, North Dakota and more recently Greece, resulting in relatively high transportation costs to pellet producers. Some Canadian bentonites available in Western Canada (Alberta) can be beneficiated for uses as pellet binders but could not compete in cost with U.S. sources due to the cost of beneficiation and the higher rail transport charges to Eastern Canada. It is difficult to find a substitute for bentonite, and many materials have been investigated by research groups but, so far, no economic substitute is in use. However, some success is apparent in studies of low cost materials such as clays, sea weed, peat moss and low grade coal, The work done by the ORF over several years has covered systematic test¬ing of Ontario clays, lignite, some types of tree bark, waste sulphite liquors of various kinds, and peat moss as binders for iron ore pellets. The major effort has been concentrated on peat moss and has included a study of the influence of different additives. Since analysis of peat moss for humic acid is difficult and time consuming, a certain amount of time was devoted to development of improved methods, the most useful of which was a spectrophotometric method based on extraction of peat by sodium pyrophosphate for determination of humic substances. In the present paper, only the most recent work concerning the use of peat moss with suitable additives is discussed in detail, since it is the most conclusive and best documented portion of the program.

Jan 1, 1971

By P. J. Cook

Comminution is one of the fundamentals of mineral processing, requiring large expenditures to be made on capital equipment, installation, power and maintenance. The trend toward lower grades and higher operating costs, mean mining operations are becoming increasingly marginal. The challenge is to improve and more importantly, utilize crushing and milling technologies that provide for reduced capital and operating costs whilst providing increased unit efficiencies. The Svedala Barmac Autogenous Crushing Mill presents such an opportunity by providing many of the cost savings and production increases required by its ability to produce a finer mill feed size and realize reduced energy consumption. This paper briefly describes the operation of the Svedala Barmac Autogenous Crushing Mill and reviews its benefits towards improving the efficiency of crushing and milling operations.

Jan 1, 1999

By R. P. Aldis

A wide range of mineral-derived products are required by the electronics industry for it to function. In one form or another, almost all the known elements have been experimented with and tested for various electrical applications. The two major areas for which minerals are used in electronics are as conductors and semiconductors. Conductors provide the means to transport and distribute electricity, while the main application of semiconductors has been to manipulate electricity. Silicon is the most widely recognized semiconductor material, but gallium, indium, and germanium are rated as the most important metals to the semiconductor industry for future and near future technologies.

Jan 1, 1991

By Clarice L. Amaral, Ricardo Melamed

Clay-coating has been used as an environmental technology tool for the immobilization of toxic elements. The mechanisms of arsenate retention in clays suggest that not only the system pH is of fundamental importance in the process but also the character of metals and ligands that compose the electrolyte system. The goal of this study was to investigate the interactions between system pH and electrolyte ions on the retention of arsenate in an Oxisol soil. The sorption of arsenate decreases with the increase in system pH, reflecting the competitive sorption of arsenate with OH groups. Solutions containing Ca tend to favour the immobilization of arsenate in a relatively broad pH range.

Jan 1, 1998

By John A. L. Dr. Campbell, James W. Haskew, F. Hoy Lee, Elliott P. Dr. Doane

Emissions of particulates, unburned hydrocarbons, nitrogen oxides (NO[ ]) and carbon monoxide (CO) from diesel engines are of concern in mines, particularly underground mines. All these undesirable products except NOx are the result of incomplete combustion in the cylinders. Various approaches to achieving more complete combustion in diesel engines have included different fuel compositions, use of catalysts, fuel additives, engine modifications, and oxygen-enriched intake air. The present study shows that injecting minute quantities of primarily platinum group metal catalysts into the intake air of a Deutz/MWM D916-6 mine diesel engine substantially reduces emissions in the exhaust. The catalyst injection system, which was developed by National Fuelsaver Corporation (Robin. 1981), transfers catalyst compounds in solution to a stream of air bubbles by a process called Bubble Fractionation (Lemlich et al.. 1966, 1968. 1970). The amounts are so minute that concentrations in the engine exhaust should be well below OSHA/NIOSH Time Weighted Average (TWA) exposure limits at steady state, a fact that was confirmed by analysis of collected particulates in the exhaust. When the catalyst injection was used along with a pleated paper filter to remove exhaust particulates, the filter operating life was shortened greatly. Therefore, this system is not recommended for use on diesel engines equipped with a water scrubber and a filter. It does offer a practical and relatively economical way of reducing exhaust emissions from other diesel engines, such as those in outby mine service

Jan 1, 1995