Search Documents

By Robert A. Haney, David J. Atchison, Kenneth G. Fields

Mining systems with greater than a 20-foot face advance (deep cut) have become popular due to their increased productivity and safety. The face dust collection system used in many of the mines employing the deep cut systems, incorporates a machine mounted dust collector with either a blowing or exhausting line brattice and a remote control operated continuous miner. In order to characterize and quantify the parameters used to control dust with these systems, the Dust Division conducted studies on four mining sections using continuous miners with deep cut mining systems. On each section, the dust control system incorporated line brattice with a machine mounted dust collector. The remote control made it possible for the continuous mining machine to advance further while permitting the operator to remain under supported roof and away from dust generated during mining. The purpose of these studies was to evaluate the effectiveness of deep cut mining systems using dust collectors to control respirable dust exposure. This paper summarizes the results of the studies conducted. At each mine face workers were sampled to determine their full-shift dust exposure. Additionally, fixed point dust samples were collected at various locations to determine relative concentrations of dust generated from mining. Air quantities were measured at each working place to determine the amount of air delivered to the face area. Evaluations were made by comparing worker exposures to respirable dust samples taken at appropriate locations upstream and downstream of the coal faced being mined. An estimate of the amount of the respirable dust being generated at the face during mining and the amount of respirable dust being removed by the dust collectors was made by balancing the air quantities and the dust concentrations immediately upstream and downstream of the coal face. Results of the studies showed that the dust control systems, were effective for controlling workers exposure to respirable dust. Dust collector efficiencies were determined to be approximately 85 percent. While the dust collectors were effective in removing respirable dust, the success of the systems with line brattice greater than twenty feet from the face, was dependent on the use of the remote control which permitted the continuous miner operator to remain out of the high concentration dust cloud in the working face. Dilution from intake air, combined with the dust collector efficiency, maintained exposure of other section workers below applicable standards.

Jan 1, 1991

By D. A. Norrgran

The recent development of rare earth permanent magnets has revolutionized the field of magnetic separation. The advent of rare earth permanent magnets in the 1980's provided a magnetic energy product an order of magnitude greater than that of conventional ferrite magnets. This has allowed the design of high-intensity magnetic circuits operating energy free and surpassing the strength and effectiveness of electromagnets. New applications and design concepts focused on the mineral and metal processing industries have evolved. This technology also led to the development of various magnetic separators specifically designed for mineral processing applications. Applications which were not previously considered are now being applied to primary mineral upgrading and recycling and secondary recovery.

Jan 1, 1993

By Haia Roffman, Amiram Roffman

A gas company operated more than 100 distribution stations. Mercury filled manometers were used for years in these stations to measure the flow of natural gas through the system. Use and handling of these manometers resulted in mercury spills and ground contamination. To assess the human health and environmental effects of these spills and the need of remediation, it was important to determine mercury specific species present and their concentrations. Soil samples were analyzed for total mercury, methyl mercury, inorganic mercury and elemental mercury. These analyses served as important input in the risk assessment performed for these stations.

Jan 1, 1998

By S. D. Thompson

Several discrete-event simulation models have been developed for designing the conveying system capacities of underground coal mines. Most of these models require the use of a step function approach to mimic the loading process at each conveyor loading point. Over the years, practitioners have generally employed one of three versions of the step function approach. An important issue is how these three versions compare to each; other in terms of simulated capacity requirements for belt conveyors. Another issue is how they compare to the peak capacity design. This paper addresses these issues by statistically and quantitatively comparing their simulation results. The consequences and problems associated with using each version are also discussed and summarized.

Jan 1, 1997

By J. Kemeny, B. Norton, T. W. BoBo

Digital image analysis systems to quantify particle size of crushed materials have successfully been applied in large-scale mining operations throughout the world. Particle size measurement at various crushing and sieving stages, especially in aggregate production, will facilitate the industry’s desire and need to achieve higher levels of process control and automation. This paper will 1) summarize applications of digital image analysis in the industrial minerals industries and introduce the Split-Online technology; 2) detail an actual recent test application of digital image analysis that ultimately lead to the installation of an automatic, non-invasive particle size distribution monitoring system; 3) document how this information is being applied: and 4) summarize the new Split-Online Aggregates Module now available.

Jan 1, 2004

By S. Frimpong, N. Demirel

Overburden excavation is an integral component of the surface mine production chain. The walking dragline is the most economic production equipment for overburden excavation in strip mining. Draglines are capital intensive, and thus, investments in multiple units severely impact the economic viability of projects. The use of few dragline units results in highly concentrated production focus, which must be efficiently managed to derive the potential economic benefits. Efficient use of draglines requires a thorough knowledge of the powered functions, the 3D rotational and translational motions and machine-formation interactions within the operating environment. Dragline kinematics and dynamics are required to understand and characterize machine performance and efficiency. In order to sustain the high productivity in difficult operating conditions, the dynamics of the dragline must be modeled and analyzed based on comprehensive kinematics. This paper investigates the planar kinematics of the front-end assembly and its interactions with the formation during excavation using the “Vector Loop Analysis” formulation with comprehensive simulation modeling in MATLAB Simulink. The kinematic models are used to examine the translational, rotational and angular displacement, velocity and acceleration components of the dragline front-end assembly along defined bucket trajectories during excavation. The results are the precursors for comprehensive modeling to examine the load deformation, torque requirements and dragline stress loading profiles for improving machine health and longevity.

Jan 1, 2006

By R. J. Sawyer

*An earlier version of this paper was presented at the IMM meeting, "Use of Cultivated Carbon in Extraction of Gold and Other Metals," held in London in January, 1983, and was subsequently published in Trans. IMM (Sect. C: Mineral Process. Extr. Metall.) in December, 1983. Reprinted with permission of The Institution of Mining and Metallurgy, London. INTRODUCTION This paper describes the development of the processing route for the Alligator Ridge Mine which commenced operation in 1980. It also reviews the modifications which have been made to improve operating efficiency during the three years that the mine has been in production. Alligator Ridge is located 70 miles Northwest of Ely, Nevada. The mine is a joint venture between Amselco and Nerco with Amselco acting as operator. The deposit consists of micron sized disseminated gold imbedded in siltstone. Although definitive conclusions have yet to be drawn as to the age and origin of the deposit, it is probable that it is young by geological standards, perhaps only 5 million years old. It is likely that the gold was brought to the surface by hot springs. As the superheated solutions rose through the porous siltstone, they redeposited minerals in the rock, forming the present ore bodies.

Jan 1, 1984

By Saurabh Rastogi, Vikram Shishodia, B. Pitchumani

Comminution is a unit operation which consumes major part of energy in mineral processing industries such as fertilizer production. Ball mills are widely used for size reduction of a given ore to the liberation size that is required in further beneficiation processes. In grinding of materials much effort is concentrated on control of top size of the product and this results in production of fines, also creates secondary problems of pollution due to the difficulty in the collection of fine particles. The present work has been carried out to control product size distribution for rock phosphate grinding in an Industrial Ball Mill of 600 TPD. The plant data are taken for a given feed distribution and mill operating conditions. The information at various Ball Size distributions are collected. The comminution functions such as specific rate of breakage and breakage distribution functions are estimated by back calculation technique to solve the mass balance equation. A simulation program is written to study the product size distribution obtained for various ball size distribution.

Jan 1, 1993

By R. Cooper, K. De Wet, A. Janwong

"Horsehead Metal Products is a zinc refinery in Mooresboro, NC, treating crude Waelz oxide (WOX) to produce special high-grade zinc by a hydrometallurgical process comprising leaching, zinc solvent extraction/electrowinning, melting and casting and bleed treatment. Cadmium removal by zinc-dust cementation plays an essential role in the bleed treatment circuit to prevent cadmium buildup in the circuit. Silica, though present at a low level of approximately 0.3 percent in the WOX feed material, had a significant impact on the efficiency of cadmium cementation with zinc dust, most likely due to the passivation of zinc dust particles with silica gel. Solid/liquid separation efficiency by filter press was also affected. To identify the source of the silica issues, silica levels were mapped throughout the circuit, and adjustments, including using pregnant leach solution as the feed to cementation, and pH control in the WOX leaching and neutralization were introduced to mitigate the issues created by silica gel in the circuit. IntroductionLocated in Mooresboro, NC, Horsehead Metal Products Inc. is a hydrometallurgical zinc refinery processing Waelz oxide (WOX) to produce special high-grade (SHG) zinc. The flowsheet, known as the Modified Zincex process, consists of leaching, solvent extraction (SX), electrowinning (EW), melting and casting and bleed treatment (Fig. 1). Cadmium cementation, part of the bleed treatment process, provides an essential bleed of cadmium from the circuit, as metallic cement. The cadmium cementation circuit consists of agitated cementation reactors, a zinc dust addition system, filter presses, agitated purification (releach) reactors and a cadmium concentrate filter press.At the refinery, WOX pulp is leached at a controlled pH to achieve the maximum zinc extraction, according to the main reaction:"

Jan 1, 2016

By Henry W. Brandt

What is the most practical method for storing a huge quantity of crude oil for a long period of time to assure availability if conditions curtail the source of supply? Underground storage is a logical answer. But can abandoned mines be used for this purpose? That is the proposal Fenix & Scisson International, Inc. submitted to the S.F.F. Association (acting in behalf of the Department of Industries of the Republic of South Africa), Johannesburg, South Africa, in October 1966. This engineering and contracting firm with headquarters in Tulsa, Oklahoma, specializes in underground storage; and based upon previous experiences their engineers were reasonably certain that a mine could be used for storing crude oil. The answer subsequently proved to be "yes." The result was con- version of a coal mine to provide storage for a quantity of crude oil which is the equivalent of a sizeable oil field. The total cost of purchasing, testing, and converting the mine was less than 15 percent of the cost of conventional steel tanks. Operating and maintenance costs are proving to be about 2 percent of those experienced at two large tank farms owned and operated by the Association.

Jan 1, 1973

By David Green

Outokumpu introduced Flash Flotation in the early l 980's for the recovery of floatable material from grinding circuits. The devel­opment came as a result of surveys made in the company's own concentrators, initiated to find ways of improving recoveries with increasingly complex and lower grade feeds. Hydrocyclones make a separation on the basis of particle size and mass, resulting in the "over collection" of fine grained, high S.G. particles. Minerals such as pentlandite, galena and gold are easily caught in the circulating load around the mill until they are overground and rendered more difficult to collect. In the case of downstream flotation this may simply involve a reduction in the rate coefficient due to the finer sizes or, as is commonly experienced in gold operations, the mate­rial is slimed and coated onto non-floating gangue and is eventual­ly lost to tails. At the time of Outokumpu's plant surveys, it was a relatively common practice, particularly in Pb operations, to have a flotation section fed directly from the secondaiy mill discharge. This is called unit flotation and certainly provided an improvement but very high wear rates and frequent sanding out of the cells was com­mon. The development of the SkimAir® Flash Flotation cell by Outokumpu provided a subtle but quite dramatic departure from the unit cell approach. Now it was possible to feed cyclone under­flow into a special purpose-built flotation machine and recover a final grade concentrate from the grinding circuit (see Figure I). The cell was designed to handle the coarse circulating load, per­mitting the coarsest fractions to be short-circuited back to the mill and retain the floatable sizes for a nominal time of 30 seconds to several minutes. The short retention time was possible largely due to the relatively clean content of the cyclone underflow stream. This means that the fine gangue is not present except in small quan­tities and most of the fine to mid-size paiiicles are higher S.G. and more likely represent valuable mineral. This condition provides for very high rate coefficients. Typical operations would recover 40-60% of the valuable mineral in this fashion and improvements in recovery were typically from 2-5% for sulphide minerals to the 5-20% range for gold and silver.

Jan 1, 1998

By C. Opoku-Ware, M. Kukay, P. Conrad, F. Inkoom, R. Pal

Researchers at Montana Tech are investigating the potential for developing trees tolerable to degraded un-reclaimed mine site tailings and soils as a solution to re-establishing long-term tree growth on those sites. This project involves growing tree seedlings from seeds planted in the degraded mine tailings and soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in degraded tailings and soils in Butte, Montana with minimal post-planting human intervention. Work conducted on the project to date has shown successful growth of seedlings in degraded tailings and soils. INTRODUCTION In an effort to improve Butte Area One natural resources, this research project is working to help restore tree growth in the Butte Priority Soils Operable Unit Boundary (BPSOU) (Opoku-Ware, et al 2018). Research by Blicker, et al (2003) found that, the BPSOU, which is part of the Silver Bow Creek/Butte Area National Priorities List (Superfund) Site within and near Butte, Montana has multiple historic mining sites situated entirely within the urban setting of Butte. Mine wastes and mill tailings, accumulated from over 100 years of gold, silver, and especially copper mining are dispersed throughout Butte, posing health risks to human and environmental receptors. Stabilization of tailings sites is needed to control fugitive dust, prevent run-off of toxic material resulting in subsequent sediment deposition in streams, reducing the volume of water seepage through acidic and heavy metal contaminated material, and improving land productivity and aesthetic values (Watkin and Watkin, 1982). If successful, the project will help restore water quality and maintain stream flow in Silver Bow Creek where it flows through Butte Area One. Trees native to Butte are being grown to seedlings in a greenhouse located on Montana Tech’s campus which will be planted in degraded soils located within the BPSOU. Growing trees is expected to help restore vegetative ground cover within the watershed contributing to stream flow in Silver Bow Creek. The trees will prevent soil and tailings from eroding and being deposited in Silver Bow Creek where they could degrade water quality and choke stream flow. The project combines research with tree seedling growth to provide a resource for Butte that could produce thousands of tree seedlings each year adapted to the harsh climate, soil, and tailings conditions that exist in the BPSOU where they will grow. It is anticipated that the trees developed by the project will have the capability for long-term survival and growth because they will be germinated and grown into seedlings in the degraded soils and tailings collected from the BPSOU where they will be planted. Soils and tailings collected for the project have been evaluated to determine if they lack nutrients or contain substances potentially toxic to the long-term growth and survival of the trees. Toxic levels of metals, high concentrations of soluble salts, extremes in pH, nutrient deficiencies and imbalances, surface crusting, high bulk density, low infiltration rates, high surface temperatures, low cation exchange capacity, restricted microbial activity, low water retention, harsh climatic conditions and surface particle movement are some of the traits of mine tailings sites that restrict revegetation efforts (Barth, 1986).

Jan 1, 2019

By J. W. Merks

At mineral processing plants the accuracy and precision characteristics of assays in mill feed, tailings and concentrate largely determine the reliability of the metallurgical balance. The accuracy of measurements is ensured by selecting effective sampling methods and efficient sample preparation procedures, and by effecting each phase without introducing a systematic error while the precision of measurements is determined by the sampling regime. Sampling systems and components, sampling methods and regimes, and sample preparation procedures will be reviewed. Different techniques to determine variance components for sampling, preparation and analysis, and to detect systematic errors in assays at mineral processing plants, will be discussed.

Jan 1, 1986

By Stephen G. Hardcastle

CANMET has developed a simple yet very effective tracer gas method to test the efficiency of stench gas emergency warning systems which can easily be performed by mine personnel. This test method uses sulphur hexafluoride (SF,) as a surrogate for such stench gases as ethyl mercaptan. The test has many advantages: it is non-disruptive to production because SF, is odourless, colourless; it is safe to use as it is inert and only a small volume, insufficient to reduce oxygen levels, is necessary to dope the air with a measurable concentration; and most importantly it provides definitive results to assess the adequacy of the warning system. Specific findings of these tests have included, over doping sections of the mine and subsequent production loss due to sickness, the warning being ignored, the injection period being too short, excessive dispersion, and inadequate notification times. The simple test protocol involves releasing a known volume of the SF, under similar circumstances to those of the stench gas, and then sampling for its presence downstream. These samples are collected in air-tight syringes which are then analyzed in a laboratory with a gas chromatograph. By direct proportion, between the size of the stench and tracer gas releases, it is possible to convert the SF, concentration into equivalent stench gas concentrations profiles. From these, it is possible to define, the initial arrival time of the gas, the time it takes to reach a "target" notification concentration, whether the gas peak will exceed TWAEV, STEV and CEV exposure limits, and the duration of the peak above these levels. Since 1993, this test protocol has been employed a total of eight times on four different Canadian mine properties and the results are being used to optimize the stench gas release system with respect to volume of gas used, duration of injection, and number of injection locations.

Jan 1, 1997

By H. Sevim

This paper summarizes the research effort in simulating the operation of "Underground Coarse-Coal Hydrotransport Systems" (UCCHS). The equipment of the system to be simulated is already optimally selected by using an analytical optimization model. The purpose of the simulation model is to test the performance of the system and to obtain the distributions of operating parameters such as water and power consumption and amount of slurry delivered to the preparation plant. Knowledge of the distributions of these parameters is essential for the efficient operation of the system.

Jan 1, 1987

By John J. Dran

Large mining companies use a number of sophisticated analytical techniques for introducing the element of risk into the valuation of mineral reserve sites. These methods include, but are not limited to, sensitivity analysis, computer simulation, conditional probability, and portfolio theory. Such techniques enable the managements of these large companies to have an awareness of the many possible ramifications of their investment decisions. On the other hand, small mining companies and individuals in the mining business, due to limited financial and technical resources, still rely primarily on single point estimates of the value of mineral reserves. These small miners introduce the aspect of risk only through the application of an appropriate "speculative" discount rate. This paper illustrates the application of a technique for the introduction of risk into investment analysis. The method appears to be most suitable for use by small mining companies and individuals contemplating a large investment in a new mineral reserve site.

Jan 1, 1974

By Wm. I. Weisman

Sometimes in assessing where we are and where we are going it is informative to take a look at where we have been. Whether or not it adds to our understanding of the present, I think it may be interesting to review some of the past history of our industry. As a starting point I chose to use the famous Paley Commission Report, formally known as "The U. S. President's materials Policy Commission -Resources for Freedom."(l) The Paley Commission report said "Fluorspar is an essential raw material for the steel, aluminum, and chemical industries." Of course this statement is still true. It also said, "United States known reserves of fluorspar would be sufficient for some 15 years at present rates of consumption--about 426 000 short tons in 1960. Projected consumption for 1975, however, is several times as great, and reserves in other free countries do not appear adequate to supply United States deficiencies during the next 25 years." This simply demonstrates how even the most learned and competent people can observe all the facts avail-able to them at a given time and yet be unable to predict the future very accurately. We all know that reserves in other countries are more than adequate to supply the United States today, 25 years since the report was published. In fact, the report estimated free-world reserves at something over 36 million tonnes (40 million short tons). Contrast this with 246 million tonnes (271 million short tons) estimated as total world reserves from the section on fluorspar from Commodity Data Summaries of 1974, published by the Department of the Interior. (2) The Paley Report discusses other matters pertaining to fluorspar that are still of interest, such as improving mining methods. Furthermore, it certainly did a good forecasting job in noting that greater recycling should become possible in the aluminum industry in regard to fluorine lost in wastes and also concerning the substitution of fluorspar in the steel industry by other fluxing materials. It also suggested that non-fluorine containing propellants should be investigated as a replacement of those containing fluorine as a conservation matter. Some discussion was devoted to recovering the fluorine content of phosphate rock, which is being practiced today, but was in its infancy in 1950.

Jan 1, 1978

By J. G. Pippenger

The Coteau Properties Company's Freedom Mine is a surface lignite mining operation located near Beulah, North Dakota. Coteau, a wholly owned subsidiary of The North American Coal Corporation, produces more than 13.5 million tonnes per year, ranking it among the largest mines in North America. In 1993, Coteau ranked seventh in terms of annual coal sales, becoming the largest mine outside the Powder River Basin of northeastern Wyoming. However, for the Freedom Mine to stand among these Powder River heavyweights, Coteau over-came several obstacles, including a coal seam with three quarters the heating value and overburden to coal ratios three times higher than the Powder River mines. Coteau's ability to compete has been built around a program of continuous productivity improvement, cost efficiency, and innovation. This report highlights a few of the major improvements implemented in recent years.

Jan 1, 1995

By Jiang Su, Alan Bloodworth

"Composite sprayed concrete lining (SCL), consisting of two layers of permanent sprayed concrete separated by a layer of spray-applied waterproofing membrane, represents the latest development in SCL tunneling, but presents several challenges to designers. This paper aims to address the following issues: (1) how to simulate composite action, (2) behavior of a composite SCL tunnel, and (3) how to utilize composite action to achieve lining thickness efficiency. It firstly sets out the background to the composite SCL concept, and then presents a strategy for numerical investigation. The main part of the paper is the presentation and discussion of the simulation results, focusing on the lining deformation, load sharing and the safety margin of both linings. Interface stresses are also examined. It is found that significant secondary lining thickness reduction may be achieved by utilizing composite action. Challenges for the design of composite SCL tunnels are briefly discussed at the end. INTRODUCTION Sprayed concrete lined (SCL) tunnelling has seen rapid development over the last twenty years in the UK (Su 2013). One of these developments has been the replacement of traditional sheet membrane and cast in situ secondary lining with innovative spray applied waterproofing membrane and sprayed secondary lining system, which has been adopted in recent major projects, such as Crossrail (Pickett 2013), and brings many benefits to the construction (Dimmock et al. 2013). The combination of sprayed primary lining, spray applied waterproofing membrane and sprayed secondary lining is perceived to provide a structurally efficient lining system that outperforms the traditional lining system, which consists of sacrificial primary lining, sheet waterproofing membrane and cast in situ secondary lining. The claimed benefits in structural performance arises from the composite action between the sprayed primary and secondary linings via the spray applied waterproofing membrane, which produces a much stiffer cross-section and therefore a more efficient use of materials. Early investigations on the design of composite SCL tunnels were carried out without (1) definite and reliable long-term interface parameters, (2) a verified numerical modelling technique, or (3) consideration of different stress histories between primary and secondary linings (Thomas and Pickett 2011, Marcher et al. 2011). This paper reports the findings from a numerical parametric study on a typical composite SCL tunnel with varied secondary lining thickness. The results show that the true benefit of composite lining arises from the optimisation of the lining thickness (stiffness) ratio between the primary and secondary linings to achieve secondary lining safety and thickness efficiency at the same time."

Jan 1, 2016

By John B. Rigg

Thank you Mr. Chairman. It was a generous introduction. It allays some of the puzzlement I have of being a minority among the speakers at this conference. I see from the program that only two of us have been asked to speak on topics in keeping with an election year. Instead of reporting facts on past events as most speakers are, J. W. Wilson, of Consolidation Coal, and I have been designated to forecast the future. Forecasting in an election year implies a liberty to fabricate at will, hallucinate, fantasize, stretch fact and fancy and generally prognosticate without regard for the consequences. Since I'm not seeking your votes, promises aren't mandatory. This will be done with supreme confidence stemming from profound wisdom and a foolproof crystal ball. So instead of soliciting your vote, I'll simply penetrate 24 years of tomorrows, which may not be much different than some of us remembering the later hours of last night. My remarks do not draw upon Gulf planning department projections. Instead they are a roll of the dice of personal conjecture to stretch your imaginations on oil shale mining through the year 2000. In this regard, it is sobering to keep in mind that it has been in my lifetime that investors wouldn't risk a dollar on paperback books, motels, supermarkets, or drive-in restaurants. And only thirty years ago it was predicted by an eminent Ivy League professor

Jan 1, 1976