Search Documents

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the key parameters influencing the gold recovery. The model was used to direct modifications to plant operating practice. The cyanide dosing strategy was changed to reduce preg-rob gold masses and cut reagent consumption A finer grind was achieved without capital investment. The density in CIL was lowered, and tighter control was exercised over plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz, and concomitant reagent cost savings of $55,000/month.

Jan 1, 1999

By S. K. Kawatra, A. K. Bakshi

Mineral suspensions in water show Newtonian flow properties at low percent solids. However, this changes to a non-Newtonian regime as the pet-cent solids increases. For Newtonian fluids, viscosity is independent of shear rate, hut, for non-Newtonian fluids, viscosity varies with shear rate. Therefore, if the slurry is non-Newtonian, attempting to measure the viscosity at a shear rate different from the shear rate experienced by the fluid within the process is futile. This is especially true for a hydrocyclone, where the rate of shear is different at different points within the hydrocyclone. In this case, it is very important to determine the flow type of the suspension before attempting to establish any correlation between the viscosity and the process efficiency. A new technique to distinguish such changes inflow type was developed. This involves two viscometers: a coaxial cylinder-type viscometer that measures apparent viscosity at low shear rates and a vibrating sphere-type viscometer that measures the apparent viscosity at high shear rates. For each of these instruments, special precautions were taken to allow, for the measurement of the viscosity of rapidly settling mineral suspensions. Because the vibrating sphere viscometer is operated at a much higher shear rate than the rotating viscometer, the two instruments together could determine the shear-rate dependency of the viscosity. Ground silica (80% passing 65 µm) in water was used to prepare slurries at concentrations ranging from 10% to 70% (by weight) solids. The viscosity of each slurry sample was measured simultaneously by both viscometers, and the results were compared. With this technique, it was found that all of the silica-slurry samples tested were in the Newtonian flow regime for up to 70% (by weight) solids. Methocel and Cellosize polymer solutions showed clear non-Newtonian behavior using this technique. This confirmed that non-Newtonian behavior of the silica slurries, if present, would have been detected by this arrangement.

Jan 1, 1997

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a longwall installation roadway (faceroad) design methodology that could be utilized by suitably qualified colliery personnel. This goal was achieved in 2012 and the design methodology (and software package) is referred to as Analysis and Design of Faceroad Roof Support (ADFRS). The intended benefits to underground operations, in the provision of this information and resource, are a safer and more productive workplace.

By M. Dale Slade, Gordon S. Bird, Robert S. Kelly

Gallium scrap is obtained from many different sources, therefore each lot received has to be evaluated and then processed accordingly. Some of the problem areas are separating small amounts of gallium from large concentrations of iron, eliminating trace amounts of gold, silver, copper, germanium, tin, and zinc from gallium, and having the flexibility to process each lot of scrap individually Following gallium from the raw scrap material to the final seven nines pure product requires stringent quality control and excellent analytical capabilities.

Jan 1, 1983

By O. A. Bascur

The problem of setting the proper control objectives and/or having several objectives to be met in the implementation of grinding control strategies can be resolved. The design and implementation of a distributed control system for safe operation of a grinding circuit while maximizing profit is presented. An optimal recovery through- put target for a desired grind is accomplished by advanced control strategies at the DCS level. A mill load constraint control technique provides stable operation with a substantial increase in throughput, while the desired grind index is maintained by an inferential grind control technique without using a particle size analyzer. The integration of crushing/grinding and flotation in the overall design was the key to the success of the project. This synergistic effect was obtained by implementing a computer plant management system in the concentrator. The overall/philosophy was to keep the implementation simple while using new technology creatively.

Jan 1, 1991

By William K. Brown

Are the results of an exploration program worth the cost? This is a question I suspect many of you are familiar with and, theoretically at least, it is an easy question to answer. The answer, of course, lies in comparing the future earnings stream the program is expected to generate, to the present value of the cost of carrying it out. While historical costs can be determined without much difficulty, estimating the value of a future earnings stream involves all sorts of assumptions regarding future costs, metal prices, inflation rates and an appropriate discount factor; and in the context in which the question arises, requires additional assumptions about mineral deposits which have yet to be discovered. As a practical matter, this kind of approach isn't likely to produce a very convincing answer; certainly not one convincing enough to satisfy a skeptical audience; nor one likely to temper the illusions of recent converts to mineral exploration, who are convinced that if enough money is spent, profitable discoveries will inevitably follow. Within broad limits, however, I believe it is possible to analyze the costs and results of gold exploration in the U.S.A. over the past 20 odd years in a useful manner. And while such an analysis is imperfect, it will provide some insight into this fascinating subject.

Jan 1, 1983

By B. Govindarajan, T. C. Rao

A simulation of batch-flotation experiments was carried out using a simple empirical model to identify the process parameters that would give maximum yield at any given ash level. The relationship between the maximum yield values and the percentage ash-reduction ratio (ARR) has shown two regions where the collector and the frother dosages have individual influences on the flotation performance. Based on this observation, a simple "selection-criterion diagram" is proposed. This diagram can he used to select the process parameters to achieve maximum yield, for a given ash content of the concentrate and at any given flotation period.

Jan 1, 1997

By M. W. Buche, E. Tarshizi, R. Chappidi, B. Inti

"Coal mining is an age-old method of power production in the world. It is also widely known for the associated risks during mining. Although the number of mishaps has dropped dramatically over the years, the number of fatal accidents is still a concern, and any aid in reducing these figures would be important to industry workers. Therefore, data from accident reports during the past seven years were collected and analyzed. Qualitative data from reports and articles provide a deeper understanding of the incidents, thus affording the possibility of identifying patterns and relationships between the accidents. For this study, a total of 119 fatality accidents occurring in U.S. coal mining operations were analyzed using advanced text mining techniques. The fatality data were obtained from U.S. Mine Safety and Health Admininstration fatalgram reports. This analysis is primarily exploratory in nature and uses term frequencyinverse document frequency (TF-IDF) methodologies along with correlation network plots. An interesting word relation pattern was obtained that identified “positioning” as the common cause of 12.6 percent of accidents, and found that 29.4 percent of accidents can be categorized as vehicle-related. IntroductionIn the mining industry, accidents are situations that employees and employers wish to avoid. They are devastating experiences to the victims and their coworkers alike. Even worse, accidents that result in fatalities create trauma and undesirable repercussions. Several measures have been taken throughout the industry to prevent such mishaps, and the U.S. Mine Safety and Health Administration (MSHA) provides continuous monitoring for miners’ safety by guiding organizations through best practices in every job role. As a result, according to MSHA, there has been a steady decline in the average number of deaths due to accidents over time. Nonetheless, any opportunity to avert one more such casualty is of paramount importance, and that is the goal of our analysis. Our objective is to identify opportunities resulting from previously unexplored directions in order to provide additional insights into potential safety recommendations. Until now, most of the studies in this area had been conducted using structured and tabulated data with a constant number of categorical and numerical variables. Unstructured text data mining is an emerging area that is still insufficiently researched and has a feasible scope for important results, as a vast majority of human communication and cognizance is comprised of words. The aim of undertaking this project by capitalizing on unstructured data is to analyze the text reports to discover potential relationships that explain the causes of accidents in new light in order to mitigate the occurrence of fatalities. The analysis in this project is based on textual data obtained from the MSHA website (2017). Individual accident reports are organized according to the date and year of the fatality. Each report includes details with images of the incident. For convenience, a simplified summary of the report is also available. Data collection consisted of gathering formal documentation of fatal accidents in the coal mining industry during the past seven years. These reports were extracted from the website in text format."

Jan 4, 2018

By W. G. Courtney

The prevention of frictional ignition with a ripper-type continuous mining machine using conical bits was investigated in the laboratory using cutter-drum-mounted water sprays. Results indicated that frictional ignition during dry cutting of sandstone with conical bits was readily obtained even at low drum rpm, while wet cutting with a carefully-designed water spray nozzle located behind the bit substantially reduced the likelihood of frictional ignition. However, the orientation and operation of the spray nozzle is critical and involves almost no margin for error. A Lee-Norse 265 ripper drum has been modified to include durable water seals and is presently being field tested underground.

Jan 1, 1987

By James B. Meredith

The European Economic Community (The Common Market) is now shifting from I a coal oriented to an oil oriented economy. The proportion of energy supplied by oil has increased from only 13% in 1950 to 38% in 1962, and will approach 50% by 1970. In the past five years Common Market petroleum demand has in- creased 15% per year compared with only 3% per year in the United States. This rapid shift to oil can be explained by looking at oil's competition, First; there is simply not enough other energy - European coal, natural gas and hydro-electric power - to meet the demand, Secondly, oil?s primary competing energy in the Common Market is coal, and Community coal is high-priced - it costs more than two and a half times as much as U. S, coal at the pithead. The third reason for the shift to oil is consumer preference for the ease of handling, convenience and cleanliness of liquid fuels. As these reasons suggest, much of the shift to oil and the resulting growth in demand would have occurred whether or not the Common Market organization had existed. On the other hand, the Common Market has stimulated the use of oil by causing a higher rate of energy consumption, and oil has been the beneficiary of most of this growth.

Jan 1, 1963

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Khaled Mohamed

Rib brows present a significant safety hazard in underground coal mines in the United States. To address this issue, researchers at the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST) are developing a practical tool to assess both the potential of rib brow formation and the stability of any formed brows. As part of this effort, a monitoring study was conducted to assess the potential for rib brow formation in coal pillar ribs. This study was conducted in a room-and-pillar coal mine where coal pillar ribs are prone to developing rib brows. Although no rib brows formed in the instrumented pillar, data from monitoring and visual observations provided valuable insights into the loading mechanisms impacting the instrumented pillar. These findings helped identify factors that may reduce rib brow formation, including the cavability of the roof in mined areas, the applied rib support, the strength of rock partings, and the overall integrity of the coal seam. The scientific findings published in the case study aid in assessing the potential of brow formation, offering additional evidence for the need to improve rib control methods in underground coal mines.

Feb 1, 2025

By Ingo Ossenbühl, Wolfgang Dolsak, Vojtech Gall, Axel G. Nitschke

"Yielding support systems for application in underground construction have a long history, primarily in mining. Typical examples are tunnels subject to loading conditions that lead to overstressing of the newly installed support or existing tunnel structures in active fault zones. Recent applications for tunnel rehabilitation projects unveiled the capabilities and flexibility of combined yielding support systems presented in this paper. Frequently, the main requirements for tunnel rehabilitation applications are a fast, safe, and simple installation along with the need for flexibility with regards to existing tunnel geometries. A combined support system consisting of steel sets with yielding connections and special groutable hoses has proven to be an efficient support measure providing a multitude of advantages compared to conventional rehabilitation approaches. The presented yielding support system provides an immediate and active support, while it allows for controlled yielding upon experiencing loads beyond its support capacity. INTRODUCTION The excavation of underground spaces leads to redistribution in the existing stress regime. This load redistribution goes along with deformations in the surrounding rock mass. Magnitude and duration of these deformations depend on the tunnel’s depth and geological conditions, but also on the installed support system. Modern civil tunneling infrastructure has generally an envisioned service life of about 120 years. Conventional tunneling provides typically a dual support system, split into the initial (or primary) and final (or secondary) lining. A typical design principle in civil tunneling is to let the vast majority of deformations acting on the initial lining cease, before the final lining is installed. Based on this approach, the loading on the final lining is significantly reduced and signs of overstressing, such as cracking of the lining, are typically limited to the initial lining. However, special cases in swelling and squeezing ground require different approaches, including yielding support systems."

Jan 1, 2016

By V. O. Tenorio, K. W. B. Requist

As the mining industry begins efforts to examine the feasibility of extraterrestrial resource utilization, the extraction and processing of icy regolith containing water and other volatile materials will be the initial focus for future expansion of capabilities. Pure water is essential for human consumption, and a source of oxygen and hydrogen. The latter, along with the volatile materials, lend themselves to the creation of fuels that may be used for further space exploration at distances not currently feasible. For any extraterrestrial scoping project, the transport of materials to geoscientists remains virtually impossible. Therefore, analysis must be done in-situ, possibly millions of miles away from the nearest human. To address the need for geologic resource estimation in the absence of geoscientists, an infrared framework has been developed for the analysis of water ice content in simulants of permanently shaded lunar regolith. This framework relies on a convolutional neural network model for the rapid analysis of percent water ice content in samples, at which point standard geostatistical methods may be employed.

Feb 1, 2023

By Emily Wortman-Wunder

As the 2009 president of the Society for Mining, Metallurgy, and Exploration, Inc., I am pleased to present the 2009 issue of Transactions of the Society for Mining, Metallurgy, and Exploration, Vol. 326. A significant portion of the contribution that we as a society make is the publication of professional and technical papers that contribute to the advancement of scientific knowledge and information transfer. Communication within the mining community is the key to a successful society. Through the information-transfer mechanisms of books, magazines, meetings and electronic media, the technology exchange that is fundamental to the existence of the Society is accomplished. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, Pennsylvania, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume certainly satisfies that intent. In keeping with SME’s tradition of promoting technological developments while honoring the past, the 2009 Transactions represents an important milestone. It is the last Transactions to appear as a bound volume. Future volumes will appear as e-books only, with some of the Transactions-only papers appearing online prior to the ebook (exactly what form the new Transactions will take is still in development). The decision to go to an all-digital format for this longstanding publication was a difficult one, but one which we hope will better serve the mining community, especially our international members. This 2009 Transactions of SME, Vol. 326, contains a total of 73 technical papers (510 pages), including all 23 papers (136 pages) that were published in 2009 in the Technical Papers Section of Mining Engineering magazine (Vol. 61) and all 32 papers (232 pages) that were published in 2009 in Minerals & Metallurgical Processing (Vol. 26). In addition, this volume contains 18 papers (142 pages) that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All 73 technical papers were peer-reviewed and approved. The process of review and publication requires much hard work by authors, reviewers and publications staff. As the 2009 president of SME and on behalf of our members, I would like to extend our gratitude to all whose efforts contributed to the publication of this volume.

Jan 1, 2009

By Judson C. Higgins

The paper addresses changes in surface transportation methods in the Industrial Minerals business starting with history, the changes to present time including such areas as energy costs, improved highways, changes in regulations and deregulation, and attempts to project future transportation trends. Transportation methods such as rail, piggyback, truck and barge are compared, and their impact on Industrial Minerals producer's costs and profits examined. The customer impact on our businesses due to deregulation is also discussed.

Jan 1, 1983

By Nawal Kishore, Nilesh Pratap Singh, Amit Kumar Verma, Vikram Seervi

In India, despite its natural abundance, demand for coal exceeds its countrywide supply due to failure to achieve high production targets, especially in opencast mines, which are responsible for 94.98 percent of total raw coal production in the country. Employment of technological solutions, such as surface miners, is key to achieving higher coal production and productivity in an environmentally friendly manner, especially in populated areas adjacent to the mining zone. This technology eliminates blast hole drilling, blasting and primary crushing units, thus reducing related environmental hazards like ground vibration and fly rocks.

May 1, 2023

By B. M. Moudgill, T. V. Vasudevan

Marine sedimentary deposits account for 80% and igneous deposits 17% of the total world output of phosphate rock. The phosphate mineral is well crystallized and exhibits a greater floatability in the igneous deposits than the sedimentary ores. Both silicates and carbonates contribute the major gangue associated with the sedimentary ores. Although removal of silica from sedimentary phosphates by froth flotation has been in practice for several decades, with the depletion of high-grade reserves, new attempts are being made to improve the efficiency of current silica removal technology and to develop new processes for beneficiation of phosphate ores associated with the carbonate gangue. In this paper, recent developments in processing of sedimentary phosphate ores containing carbonate and silica gangue are discussed.

Jan 1, 1987

By I. Iwasaki, H. Dho

Two aromatic-type chelating agents, 1,10 phenanthroline (phen) and 8-quinolinol (quip), were tested as specific depressants for magnetite in the cationic silica flotation of magnetic taconite concentrates. Micro and batch flotation tests, along with zeta potential and adsorption measurements, were used. In the presence of a cationic collector, dodecylammonium chloride (DAC), the Fe/phen surface chelate electrostatically repelled DAC, and the magnetite was depressed. The negatively charged Fe(quin)2(OH)2- on the magnetite surface attracted the cationic collector and made magnetite floatable.

Jan 1, 1997

By S. Mathur

Future Florida phosphate reserves contain higher MgO than presently mined deposits. The high MgO content is contributed by dolomite and Mg-rich clay, palygorskite. Selective flocculation was attempted to reduce the MgO content of apatite in synthetic mixtures of apatite with dolomite and palygorskie. Mixed mineral selectivity was predicted in the apatite-dolomite and apatite- palygorskite systems with Poly(ethy1ene oxide) (PEO) flocculant. Loss of selectivity in the mixed mineral systems was primarily attributed to heteroflocculation, which was minimized by addition of a Site Blocking Agent (SBA), a lower molecular weight fraction of PEO, prior to addition of the flocculant. A 80:20 mixture of apatite-dolomite (or palygorskite) was upgraded as 95% apatite at more than 80% recovery level in the product fraction.

Jan 1, 1995

By H. T. Mikkelsen

Mineral production implies emissions of particulate matter (dust), noise and vibration that may cause conflicts with neighbors living nearby. In Norway a few conflicts has been brought to court, the latest in 2006. This paper discusses dust emissions and dust depositions (dustfall). The pollution authorities have accepted monitoring of dustfall instead of suspended dust as the first step in conflict cases concerning small and medium sized enterprises. In the case of exceeded limit values, the second step is to require monitoring of suspended dust and next the implementation of control actions to reduce dust emissions. Dustfall monitoring programmes carried out at six mineral production plants in Norway, show that the mineralogical rates of dustfall are rather low a few hundred meters away from the plants or the tailings disposal. They are mostly considerable lower than the limit value of 5 g/m²/30days accepted by the authorities. Seasonal variations between mineralogical and organic dust fractions can be observed in Norway, with higher content of mineral dust during winter time. Other sources to mineralogical dust can be recognized. During winter time wear of road pavement and sand on icy roads can give high emissions of mineralogical dust to the ambient air. Parallel monitoring of suspended dust and rates of dustfall indicate that dustfall can be used to estimate the level of suspended dust. A model for estimating suspended dust based on records of dustfall is presented.

Jan 1, 2007