Search Documents

By E. Watkins, R. Kimutis, H. Dougherty

Gas wells have often intersected mining resources, but unconventional shale well drilling has more recently challenged mines to balance the risk of interaction due to higher pressures and larger quantities of gas. Full extraction mining, such as the longwall method, induces ground movement that may influence the casings if wells are drilled within the mining area. The possibility of a casing shear would lead to the risk of unplanned gas migration into the mine. This has the potential to quickly overcome the ventilation system and reach the explosive range which, if ignited, can have catastrophic consequences on the health and safety of underground workers. The utilization of network software to model mine ventilation is a common practice in the mining industry and can assist with a well breach scenario. This work focuses on a well breach in between two longwall panels after second panel mining with gas entering primarily through the gobs of the adjacent longwall panels. Applying the network software Ventsim, a gob zone and ventilation network were created to better understand the distribution of gas within the mine and the limitations and effectiveness of a ventilation system. The model shows both a transient flow simulation and steady state concentrations throughout the mine ventilation system. Using a standard Pittsburgh coal seam longwall ventilation scheme, we find that the system can dilute a significant inflow of up to 700 cfm of methane.

Mar 2, 2022

By Ken J. Richards

Industries dependent on pyrometallurgical processing generally find themselves facing a common set of problems, namely, serious environmental restrictions, heavy capital requirements for new facilities and for plant modernization, the certainty of rapidly escalating fuel costs, and the uncertainty of fuel availability. To remain competitive, it has become clear to industry that a new dimension of attention must be given to assuring the maximum performance from plant facilities already in place and from those that are built in the future. In the last decade or so, in response to these needs, there has been an acceleration in the development of new pyrometallurgical process concepts. Their application, though spotty, is increasing. A common factor in this developing base of technology is the need for effective process control. Digital control is an indispensable element of meeting the challenge. We cannot make the point, however, by looking to a general survey of instrumental control of pyrometallurgical processes. Computer control is in its awkward adolescence. Its application is so new that only isolated applications can highlight the trends. For this reason, the authors have chosen to focus on the nonferrous smelting industry to illustrate the status of pyrometallurgical processing and control. We believe this approach will best meet the interests of most readers of this edition and the background of the authors.

Jan 1, 1979

By D. D. Banerjee, S. K. Kawatra, T. C. Eisele

To reduce their sulfur emissions, many coal-fired electric power plants use wet flue-gas scrubbers. These scrubbers convert sulfur oxides into solid sulfate and sulfite sludge, which must then be disposed of. This sludge is a result of reacting limestone with sulfur dioxide to precipitate calcium sulfite and calcium sulfate. The majority of the sludge is simply landfilled, but with increasing landfillimg costs this can cost the plant millions of dollars per year. As a result, this option is rapidly becoming less attractive. Producing marketable materials from the sludge is a far more promising avenue, provided that the products can meet the necessary specifications at a reasonable cost. In this paper, a method is described for using froth flotation and water-only cyclones to remove unreacted limestone from scrubber sludge. The water-only cyclone was found to be very effective for removing the coarser unreacted limestone, grinding ball chips, gravel, and similar coarse impurities. Froth flotation was found to remove fine unreacted limestone, with a minimum of reagent addition.

Jan 1, 1995

By E. D. Sehnke

The refractory materials industry provides the largest commercial market for nonmetallurgical grade bauxite. Refractory grade bauxite is prepared from bauxites having low iron, titania, and alkali content by calcining at temperatures near 1,650° C. Although there are substantial bauxite reserves in the world, premium grade bauxite ores suitable for use in refractory applications are limited to only a few specific sources, primarily in Guyana and the People's Republic of China. Consumption of bauxite for refractory use is closely associated with the production and consumption of primary metals, in particular iron and steel. Barring major disruptions within the principal producer nations, sufficient supplies of refractory bauxite will be available to meet world demand well into the next century, and raw material costs will continue to determine the availability of markets for bauxite-based refractory products.

Jan 1, 1992

By V. A. Shea-Albin

Sandstone escarpments surrounding western coal-bearing plateaus serve as critical habitat for animal species. Effects of mining subsidence on escarpment stability are not well documented; therefore, regulatory agencies may limit extraction of coal reserves underlying escarpments. Because millions of tons of this coal exist on Federal Lands, associated public revenues from Federal royalties, and valuable coal reserves, risk being lost. The U. S. Bureau of Mines is using numerical modeling techniques to analyze effects of subsidence on escarpment stability. Finite element models that incorporate bedding plane slip, gob formation, and movement along joints simulate escarpment subsidence observed in the field.

Jan 1, 1994

By M. G. Karfakis

Grouting has been used in underground mining for more than twenty years. Chemical grouting is often used as a remedial measure when the implemented ground control program is unable to completely prevent structural failures or when there is a need for preventing a structural member from unraveling. Utilization of the polyurethane grout currently being used is restricted by its limited range of physical and mechanical properties that restrict its utilization. To overcome some of the drawbacks of polyurethane, research has been conducted on a newly developed polyester based grout. The polyester resin, identified by Sandvik as StrataGrip, provides a number of features, including variable gel times and much reduced chemical hazard. Equally important are the mechanical properties of the product. The strength and deformability of any chemical grout must be compatible with the intended purpose of grouting and the expected deformation of the rock that is to be grouted. Assessment of the mechanical properties of polyester grout is the focus of this work. Field experiences and laboratory research have defined the properties of an effective grouting material. Experimental results indicate that the polyester grout meets or exceeds the recommended properties for many injection applications. Furthermore, the results suggest that the ability to adjust mechanical properties via resin formulation has the potential to expand the applicability of chemical grouting in ground control.

Jan 1, 1997

By F. F. Aplan

Rather than reiterate what is well known about the flotation of the non-sulfide minerals, emphasis has been placed on those separations which are not so effective. These difficult separations are largely connected with problems of selectivity in the flotation of the base metal oxides, the other slightly soluble minerals, the insoluble oxides and the naturally floatable minerals. The paper discusses possible methods of improving selectivity between similar species and of improving selectivity against the gangue minerals.

Jan 1, 1994

By DEBASHISH MISHRA, SOMU MANDAL, ASFAR MOBIN KHAN, JAI KRISHNA PANDEY, NIROJ KUMAR MOHALIK, SANTOSH KUMAR RAY

Coal is a low-cost fuel with high calorific value. Statistically, the global coal mining industry suffered 12,489 fatalities in 104 reported mining accidents from coal dust explosions during 1900 to 2020. This review article discusses the occurrence, mechanism and explosibility parameters of coal dust explosions and presents a literature survey of the laboratory and computational fluid dynamics (CFD) simulation methods of studying them, as well as a comparison of the two methods.

Feb 1, 2023

By Robert C. White, Kurt W. Keskimaki

The Henderson Mine is a large underground panel cave molybdenum mine located near Empire, Colorado. Diesel equipment is employed for all development work, as well as production ore handling. Due to fluctuating demand for molybdenum, production rates have varied from 16,000 to 32,000 metric tons per day (18,000 to 36,000 short tons per day) over the last four years. In order to obtain the maximum air flow for minimum power cost the Henderson mine has completed the following modifications to the ventilation system: removal of large intake fans, elimination of underground booster fans, shutdown of tunnel exhaust fans, completion of the number 5 exhaust ventilation shaft, and use of partially debladed main exhaust fans. These changes have reduced the annual cost of mine ventilation at the Henderson Mine by over 80 per cent, a very critical cost savings in today's competitive molybdenum marketplace.

Jan 1, 1989

By R. Sellaro

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, CWP and silicosis are major concerns. While there have been many studies aimed at understanding total dust concentrations and silica content associated with different mining conditions (e.g., locations/occupations within a mine, cutting methods, geologic strata), little research has been completed to more comprehensively characterize respirable dust (i.e., by particle composition, size distributions, shapes). This preliminary study sought to characterize dust from an underground coal mine in Central Appalachia using scanning electron microscopy with energy dispersive x-ray (SEM-EDX). Respirable dust samples were collected from various locations in the study mine, and individual dust particles were identified and classified by mineral type. A continuous personal dust monitor was also used to estimate total respirable dust concentrations during sampling. Here we report initial results of this work, and discuss advantages and challenges of particle-level characterization of mine dusts in terms of occupational health research.

Feb 23, 2014

By Bjørn Nilsen

"INTRODUCTION/BACKGROUND Weakness zones or faults containing clay-rich gouge represent one of the most challenging rock mass conditions to be encountered during tunneling. In Norway, such conditions count for a large part of the rock support costs, and in cases where the rock support has been insufficient, serious instability and cave-in have in many cases been the result. Most commonly, such cave-in has occurred after water filling of hydropower tunnels, but in some cases it has also occurred in tunnels under excavation and in completed “dry” tunnels. To avoid instability, two important requirements have to be fulfilled: 1) The location of the weakness zone and its character have to be identified in time. 2) The rock support has to be sufficient to withstand the loading caused by the zone. An incident which really brought the problems related to swelling clay into focus was the cave-in at the Hanekleiv road tunnel in 2006. Here, rock fall from the roof as shown in Figure 1 occurred unexpectedly about 10 years after the tunnel was completed. Fortunately this happened at a time with very little traffic, and nobody was injured. This incident emphasized the significance of the issue of swelling clay, although it was found to be caused also by gravitational collapse of the clay-rich gouge material of the weakness zone, and not related to swelling only (Nilsen et al. 2007).In this paper, main focus will be on discussing the characteristic features of swelling clay, test procedures which are being used for characterizing swelling clay, and the reliability of the results from testing for use in support evaluation and design in conditions with swelling clay. It is generally well known that swelling clay may cause considerable pressure on support elements, but quantifying this pressure for reliable analysis and design of rock support is still a great challenge."

Jan 1, 2016

By Gerald G. Griswold, Allan G. Provost

"To Sink or Not to Sink"; this play on the Bard's words sums up the considerations and problems that face the owner on every potential shaft sinking project. The growing demand for access into the earth is pressing construction into new areas and to greater depths. The following discussion will entertain some of the effects of these new and unknown aspects upon the approach to designing and sinking of deep shafts. We will also look at the current shortages of equipment, materials and skilled manpower, and their effect upon the planning and sinking of shafts. Particular emphasis will be placed upon equipment selection, and we will discuss how economics, while always a prime consideration, is now, more than ever, both an incentive and a detriment to the industry. FUTURE CONSIDERATIONS Shaft construction is assuming ever increasing importance both in mining and civil endeavors. The rapid depletion of near surface mineral reserves is requiring the mining industry to look deeper into the earth for new sources. These greater depths increase the exposure to unfavorable geological conditions; heavier ground, high water pressures, and high temperature. South African gold mines have now reached depths of 12, 000 feet, where the rock temperature is 1380 and water bursts from the fissures. In North America depths to 7, 500 feet have been sunk, but deep shafts are still generally considered to be those of

Jan 1, 1974

By D. K. Marjaniemi

The U.S. Bureau of Mines inventoried and characterized mineral sites and production plants within 200 km of the border in both the U.S. and Mexico. Sources of information included the USBM Minerals Availability System, the USBM Automated Mineral Information System, the USGS Mineral Resources Data System, the Mine Safety and Health Administration Address/Employment File, and the literature. Three hundred seventy-eight major construction material and industrial mineral properties were identified and characterized in the U.S. and Mexican parts of the Borderlands. Sixty-six major metallic mineral properties were identified and characterized in the Mexican part of the Borderlands.

Jan 1, 1996

By Crystal Poon, Paul Matlashewski, John Morkeh, Kathryn Dorfschmidt, Jose Carvalho, Chad Williams

Rockfall hazards are ubiquitous in mining environments making their control critical for safe mining operations. The complex processes involved in rockfall events necessitate a probabilistic modeling approach with well-calibrated material properties. The controls designed to mitigate rockfall hazards need to be reliable, efficient, and safe to deploy to meet the constraints present at an active mine. This paper presents an innovative solution to rockfall at Rio Tinto’s Bingham Canyon Mine. The solution incorporates the site-specific calibration and creation of a predictive rockfall model with the design, field testing, implementation, and monitoring of the rockfall controls.

By Lewis J. Patterson

In the period of time allotted to this paper, an attempt will be made to cover a great deal of territory, figuratively speaking, as far as our experience with ammonium nitrate is concerned. In giving this subject the "broad-brush" treatment, it will be necessary to generalize on the major points which at the same time will permit me to avoid, to a great extent, any involvement in the purely technical and theoretical aspects of blasting. The practice of theorizing before a new idea is tried has practically been discontinued in our organization simply because experience has shown that, almost without exception, theories have fallen aside as some new development takes its place. In regard to blasting, logic and experience seem to have little place in this phase of quarry operations. As the use of low cost blasting agents was introduced in our operating practice, a man who had no previous experience in the field of blasting but with sound knowledge in safety procedures was given the responsibility of supervising the drilling and blasting operations. A total lack of experience is not ordinarily recommended as a prerequisite to assuming the responsibilities of a supervisory position. However, in this case it was obviously a wise decision because there were no pre-conceived ideas as to what techniques would or would not be successful.

Jan 1, 1958

By R. H. Thorpe

In the earliest days of mining coal the obvious method was by bord and pillar working. Longwall in Britain developed from this as an expedient to overcome bottlenecks arising from ? 1) increasing depth of seams causing roof control difficulties; and 2) ventilation problems. This system became almost universal particularly in the thicker seams, where faces of up to one mile in length were not uncommon. Coal getting in these faces was usually by pick and shovel, filled into small waggons of up to 15 cwts capacity. These waggons ran on rails laid alongside the coal face and were often taken away from the face to the main haulage roads by horses. The roof was supported by rigid props and the wastes were normally controlled by strip packing. This system of mining was very flexible and worked well down to sections of about 3'6"

Jan 1, 1976

By Ignacio Salazar

Somebody sure gave me the wrong title. I can talk much more freely about the impact of the anti-nuclear movement on the DRILLING industry in New Mexico. In a word, it is being "clobbered." It doesn't seem like very long ago that my brothers and I were busy trying to find enough new equipment (and trying to talk bankers into lending us enough money) to keep up with drilling work we could get. Seemed like no matter how hard we worked, and how much money we borrowed, we were always one step behind where we wanted to be. We had so many holes to drill that all our crews were working three shifts a day, and over several states. The nation needed energy, and we were ready to help supply it. Exploration and development drilling jobs were all going full-blast. We had trouble keeping up with them. With luck, we figured we'd be able to get all our equipment out of hock before all the necessary uranium mines were developed.

Jan 1, 1979

By T. Matthews

"One critical factor in mineral reserves reporting, as well as mine-reserves reconciliation, is the impact of dilution and ore loss in the mining process. This paper considers the implications of various factors on dilution and ore loss projections, by orebody geometry, mining method, and ore control systems. We also discuss the implications of resource estimation methodology on dilution for reserves. DEFINITIONS Dilution and ore loss are two critical concepts in mining, which address the differences encountered between modeled grade and tonnages and actual production. Dilution is volume increase and grade reduction caused by multiple factors, chief among which are mining of waste material along ore-waste contacts, mining of internal waste as ore, and misclassification of waste as ore in the ore control process. There are also geostatistical and estimation aspects sometimes lumped with dilution, including the volume-variance effect (the tendency for small volumes of material to include a less regular distribution of grade than large volumes of material). Ore loss is described as reductions of ore volumes in the mining process due to misclassification of ore as waste in the ore control process, exclusion of discontinuous mineralization from mining due to geometry or continuity, and mechanical losses in the mining process. Dilution is typically taken as an increase in tonnes of ore with no change in contained metal (and thus results in a reduction in grade.) (Some workers consider the likely grade of the diluting material as well, particularly in deposits with gradational grade boundaries—this will be addressed later in the text.) Ore loss is typically taken as a reduction in tonnes at average grade of the ore, and thus results in a reduction in both tonnes and contained metal. If model (resource) tonnes are Mt, grade is Mg, and contained metal is Mm, the resource with ore loss (L) and dilution (D) included (Rt, Rg, and Rm) will be:"

Jan 1, 2015

By Z. Abdel-Khalek, Hassan El-Shall, S. Farrah, C. Boice

Selective adsorption and surface modification of minerals by surfactants is the primary step in the process of separating certain minerals with similar physical and chemical characteristics in the flotation process. In this study, microorgan- isms are used as surface modifiers for francolite and dolomite. Results of adsorption experiments with francolite and dolomite show that the microbes selectively adsorb to one of the minerals under specific operating conditions. In preliminary flotation experiments, it is found that the microorganisms enhance or depress flotation of the minerals leading to an increase in the efficiency of separation between the francolite and dolomite. The conditions leading to selective adsorption (surface modification) and subsequently to possible efficient separation of these two minerals are discussed in this paper.

Jan 1, 2002

By Neil B. Prenn

Drill-hole contamination has been a problem for many years. Contamination of rotary drilling has been well documented. More recently contamination in wet reverse circulation drilling has been noted by Echo Bay and others at the 1991 AIME annual meeting. Mine Development Associates (MDA) has worked on a number of projects at which contamination of drill-hole samples has occurred. Properties are commonly acquired with drilling accomplished by other companies and at times the only records of the drilling program are the drill-hole logs and assays themselves. Identification of contaminated zones is sometimes difficult to determine. Most geologists and engineers in the industry are aware of the magnitude of the problem, as contamination is a relatively common problem with wet reverse circulation drilling. MDA has developed a computer program to help determine if contamination has occurred when using reverse circulation drilling, based on cumulative distribution curves and by a process we call decay analysis. Most deposits are not homogeneous throughout the deposit, but exhibit a characteristic drop-off or decay of assay values around higher-grade drill-hole intercepts. Using graphs of this characteristic decay and cumulative frequency distribution, we can use the program to help determine contamination in several ways. This paper will discuss the use of decay analysis at three gold deposits where contamination is known to have occurred. In one of the deposits decay analysis was used, successfully to determine if contamination had occurred, while in the other two the decay analysis was used to verify our decay analysis procedure.

Jan 1, 1992