Search Documents

By L. G. Stolarczyk, J. Duncan

"SynopsisLong before the environmental movement, coal miners were suffering from occupational diseases that became apparent in the later years of service, and especially during the retirement years. Chronic exposure to micro-fine dust in the respirable range (‘float’ dust) causes various lung diseases, referred to as coal mine dust lung disease. In the USA alone, 76 000 miners have died of coal mine dust lung disease since early legislation recognized the issue in 1969. Researchers believe that reducing float dust exposure limits alone will not reverse the increasing incidence of coal mine dust lung disease seen in the current generation of miners. Trace and radioactive metals are concentrated in the thin boundary layers of the coal seam (Roberts, 2013), and hence float dust includes silica and toxic trace metals. The production and quality of coal is also significantly impacted by the presence of these contaminants in the coal. In the combustion process, the trace metals are oxidized and become incorporated in the fly ash and flue gas. Since they are extremely water-soluble, they represent a significant danger to health and the environment. Coal preparation plants and power stations need to mitigate these contaminants as far as is practical, but the simple fact is that most contaminants should have been left un-mined.This paper describes an innovative coal-cutting solution to the longstanding technology gap in mining – the ability to measure uncut coal layer thickness to the boundary rock layer. Because of constant changes in geology, seam thickness, and seam undulation, the horizon sensor must be located in the bit-block of the rotating cutter drum of the mining machine. Contaminants in ROM coal must be minimized at the source – that is, at the rock/coal crushing cone directly under the bit-tips of the cutting drum. Bittip distances to the rock boundary layer must be automatically controlled in real time when mining in a complex and undulating coal bed. Horizon sensing (HS) technology enables the mining machine’s cutting picks to stop at a specified distance from undulating horizons of the boundary rock. The thin contaminated coal layer can be left in situ, significantly reducing the toxicity of the float dust. Preventing the metal picks from striking quartz-containing boundary rock also reduces the occurrence of methane ignitions. HS technology equipped with pick force vector sensing can allow optimization of the cutting pick lacing pattern for minimum coal and rock crushing, thereby reducing float dust. This technology may enable the mining industry to convert from automated machine control to autonomous during coal cutting and loading."

Jan 1, 2015

By Du Sichen, K. Mukai, S. Seetharaman

Viscosities of slags constitute an important physical property needed for an understanding of the mass transfer phenomena in metallurgical processes. Viscosity is also the key that leads to a better understanding of the structure of slags. It is well known that the viscosities of silicate slags decrease with the addition of basic oxides due to the breaking of the silicate network. The measurements of slag viscosities often pose experimental challenges, especially to the choice of materials. The keynote lecture takes up the experimental problems and the various techniques adopted. Dynamic viscosity measurement, as a powerful tool towards an understanding of the kinetics of some high temperature reactions, is brought out. A number of semi-empirical models have been developed to estimate the slag viscosities in the case of multi component slags. A critical survey of these models is presented in the lecture. Earlier models by Riboud et al., Urbain et al. and Mills et al. have been developed further into a new generation of models. Some of the current important models are (1) Model by Iida et al. (2)CSIRO model (3) Pyro research Model (4) Model by Tanaka et al. (5) Model approach by Reddy et al. and (6) KTH-model. The predictions and capabilities of the various models are compared. Estimations of viscosities from thermodynamic data and prediction of liquidus temperatures from viscosities are presented. The concept of surface viscosities with reference to slags and viscosities of two-phase mixtures are also taken up in the presentation.

Jan 1, 2004

By W. V. Mutler

Present day capital costs are analysed for a 2 000 metric tonne per day (MTPD) pyrite burning plant and compared with a sulphur burning plant of the same capacity. Power, raw material and steam production rates are then compared for the two facility types. A sensitivity analysis is conducted to highlight the impact changing sulphur, pyrite, capital and operating costs have on the relative economics of these feeds. Technological improvement effects on capital cost and energy recovery are also discussed. Besides the steam produced from the burning of pure sulphur or pyrite, plants using an advanced form of heat recovery can produce up to 10 bar steam using heat from acid formation. The quantity depends on the overall water balance which is influenced by such factors as gas strength and product acid concentration. Modern materials and innovative process design also improve the ability to increase the high pressure steam from the roaster boiler in pyrite plants above the traditional 1.25 kg of superheated steam per kg of acid produced.

Jan 1, 2009

By M. F. Handley

Sequential grid mining has been employed as the primary mining strategy at the AngloGold West Wits Elandsrand Mine since the inception of stoping operations from the sub-vertical shaft system in 1988. Little has been published on sequential grid mining as a mining strategy since, and the purpose of this paper is to describe sequential grid mining, its history, its implementation at Elandsrand, and the outcome to date. The results obtained using sequential grid mining have been evaluated from seismic data, productivity statistics, and rock related accident statistics. Comparisons with neighbouring mines namely Western Deep Levels and Deelkraal, have been made to substantiate the improved conditions observed at Elandsrand, and to compare sequential grid mining directly with longwall mining in similar conditions and at similar depths. Sequential grid mMining is shown to be cost-effective, more flexible, and safer than long wall mining in similar conditions, at least on the Ventersdorp Contact Reef in the western part of the Carletonville Goldfield. More work is necessary to establish it as the favoured mining strategy at depths exceeding 3000 metres, and for reefs other than the Ventersdorp Contact Reef.

Jan 1, 2000

By I. McDougall

The matte/slag tidal zone in a nickel-copper-iron-sulphide matte smelting furnace is subject to severe process conditions that can lead to premature failure of the lining. The MgO-FeO-SiO2 slag is aggressive to refractory bricks, while the Ni-Cu-Fe-S matte is aggressive to water-cooled copper cooling elements, and can penetrate and sulphidize refractory bricks. A novel approach to the lining design was taken at a PGM smelting furnace, where an indirectly-cooled graphite ring was applied in the matte/slag tidal zone, with refractory bricks on the hot face. The graphite was cooled by the copper cooling elements in the slag zone, obviating the need for copper cooling elements in the tidal zone. In this paper the effectiveness of different lining designs utilizing varying degrees of cooling in the slag zone and slag/matte tidal zones is compared. In comparison to water-cooled copper in various configurations, cooled graphite shows promise as an indirect refractory cooling system in the tidal zone area of furnaces. Keywords PGM smelting, graphite, refractory lining, copper cooling elements, submerged arc furnace.

Aug 1, 2013

By J. L. Viljoen

t has long been the drive of the industry and all operations to create an environment that is free of injury and illness. We have come a long way; the leaders, executives, managers, supervisors and workers are to be commended for relentlessly driving to create, what I call a ?White Flag Day Every Day?. Yet I am also aware of the huge shift we still need to create in the industry, on the operations and in the workplaces to have them free of injury and illness. Keywords People, values, care, trust, belief.

Jan 1, 2011

By G. A. Bezuidenhout, J. P. T. Kapusta, D. K. Chibwe

"Peirce-Smith converters (PSCs) are extensively used in the copper, nickel, and platinum group metals industries. The typical converting operation involves lateral purging of air into molten matte through a bank of tuyeres. This blowing operation occurs at low pressure from the blowers, resulting in a bubbling regime that is considered inefficient from both a process and an energy utilization perspective. Inherent drawbacks also include recurrent tuyere blockage, tuyere punching, and low oxygen efficiency.Western Platinum embarked on a full-scale industrial evaluation of generating a jetting regime by using sonic injection. Prior to industrialscale tests, a numerical assessment to ascertain the feasibility of implementing sonic injection into a PSC was conducted. The work included flow characterization at high-pressure injection achieving sonic velocity at the tuyere exit. The 2D and 3D simulations of the three-phase system were carried out using the volume of fluid method together with the RKE turbulence model to account for the multiphase and turbulent nature of the flow.This paper discusses the key findings in understanding plume extension, velocity distribution, shear wall stress analysis, and phase distribution characteristics in the system. Plant trials are also discussed with reference to the commercial aspects of a full-scale implementation of sonic injection in the smelter."

Jan 1, 2015

A number of impending and actual pit wall failures have been observed and documented, which have been interpreted to initiate on newly generated structural features. This infers failure through intact rock. Failure mechanisms have been postulated resulting from circumferential stress, extensional strain and brittle flexure. These will be discussed in the context of the failures and the associated monitoring. The implications of failure initiating on ?unknown? features has a significant impact for deep open pit mines where designs are based on the expected structural regime. Being able to anticipate such failures is important for design. Equally important is management of such changes as they arise. In this context, monitoring using high resolution microseismic techniques will be discussed as a means of providing early warning of such failures.

Jan 1, 2006

By T. Y. Yunsel

Estimation techniques such as polygonal, triangular prism, trapezoid, isopach maps, and inverse distance methods are often used in ore or industrial minerals deposit evaluation. These techniques do not express the variability of the deposit and do not allow a determination of the reliability of the estimates. However, geostatistical methods can express a measure of the error associated with the estimates, by finding weighting coefficients for a given mining block, and can also help with data configuration that minimizes the error. This work addresses an application study on the quality and reserve characteristics of the cement raw materials of the Adana Cement Factory in Adana, Turkey, based on the spatial distribution and variability of the chemical components (Si02, CaO, A1203, Fe203). The study has been carried out using a geostatistical procedure that is useful for site assessment, characterization, and monitoring situations where data are collected spatially. Directional and omnidirectional experimental variograms of the cement raw material variables showed that neither strong geometric nor severe zonal anisotropy exists in the data. The most evident spatial dependence structure expressing the continuity for omnidirectional experimental variograms were characterized by exponential and spherical variogram models. These models have been used in cross¬-validation analysis, which proved that these models, their parameters, and kriging parameters are applicable for the study area. Quality contour maps of the deposits at given levels underground were estimated using a kriging interpolation technique. Anomalies such as bullseyes and drift were not observed in the maps that were generated. Kriged maps showed the spatial distribution of quality continuity and variability of the deposits. Grade-tonnage curves and total tonnage estimates in the particular grade were determined using ordinary kriging in order to improve the mining operation and planning. Consequently, local uncertainty and the probability of extreme values occurring are tools of prime importance for the mine planning, the optimum mix of raw materials coming from different quarry stopes.

Jan 1, 2012

The paper provides a brief review of a multivariate uniform conditioning and a localized multivariate uniform conditioning (LMUC) technique, and presents a production reconciliation case study based on a porphyry copper-gold deposit in Peru. The reconciliation study compares the longterm LMUC mineral resources model (typical of new mining projects, which are invariably based on drilling data on a relatively large grid) to the corresponding production blast-hole grade control model, as well as the final plant production.

Jan 1, 2014

By I. Bock

Selective Blast Mining (SBM) makes use of milli-second sequential blasting technology to separate the valuable reef material from waste rock in the blasting operation at stope faces in the mining of tabular ore bodies such as exist in the gold and platinum mines in South Africa. The waste rock is cast blast to the back of the stoping area, and the reef material is fractured and deposited close to the stope face. Only the reef material is transported to the surface. A simplified economic model is presented to evaluate the economic benefits of SBM. Although premature, in that adequate experimental demonstration of the validity of the model has not yet been possible, the model is presented since it indicates substantial benefits in the case of narrow reef gold mines. It is suggested that many marginal mines should seriously consider SBM. Benefits can also be realised in platinum mines, but a lot more experimental work is necessary to establish cost parameters more reliably. Some practical experience in the use of SBM in the mining of the UG2 reef is presented.

Jan 1, 1998

By V. Mathebula

Paper written on project work carried out in partial fulfilment of B. Tech (Mining Engineering) degree The purpose of this study is to establish whether to mine the Bottom of Pit (BOP)/TOB 4 reserve before the commencement of the Block Cave or whether this should be disregarded and the reserve be extracted at the end of the life of the Cave. The primary goal of this report is to investigate and propose a practical mining method to safely extract the reserve given the set constraints. This report quantifies the additional revenue the TOB 4 will contribute to Finsch?s overall NPV thus enhancing Finsch?s business case and strategically enhancing the SBP. Several underground mining options have been investigated. The proposed mining method includes the installation of a series of extraction tunnels below the TOB 4 reserve from 53 level, with a slot access tunnel system. Ground will be loaded by LHDs from the draw points and tipped into 50-ton dump trucks at a transfer point, from there the ground will be transported to 53 level No. 1groundpass where it will join the existing ground-handling system. Primary development is scheduled to begin October 2002 and last for a period of approximately 7 months until early April 2003.The production is broken into 4 phases. Phase 1 is scheduled to begin mid-April 2003. The final production phase will be completed by November 2005. The production scheduling has been designed in order to remain ahead of the Block 4 undercut in order to ensure stability and safety. Due cognisance was taken of the health and safety of all employees concerned during the design of the mining and ground-handling processes for the Bottom of Pit. As far as is reasonably practicable, the BOP was designed and will be constructed and equipped to provide conditions for the safe operation of machinery and a healthy working environment for people underground. Relevant requirements of the Mine Health and Safety Act regulations pertaining to mining operations have been identified and adhered to during all phases of the design process.

Jan 1, 2004

By H. Copur

Experimental studies for quantification of force and brittleness indices relevant to rock cutting performance are presented. A simple interpretation method is developed, which quantifies the force-penetration response obtained from indentation tests. Basic parameters of the quantification are force increment and decrementrates, force increment and decrement periods, and number of increment and decrement data points. Blocks of eleven different rock samples were collected from different operating mines in Turkey and subjected to indentation tests to calculate the indices. The samples included harzburgite, serpentinite, trona, limestone, claystone, two different sandstone samples, siltstone and three different chromite ore samples. The concept was validated by a set of full-scale linear cutting tests using a conical cutter for measuring the cutting performance in relieved and unrelieved conditions, i.e. cutter forces, specific energy, size distribution of rock cuttings. The rock cuttings were sieved to determine coarseness index, indicates coarse chip generation characteristics, and size distribution. The force index is moderately correlated with the cutting performance and mechanical properties of the rocks, and poorly correlated with the coarseness index and size distribution of cuttings. A general and moderate trend is observed between the brittleness index and the coarseness index, cutting performance for unrelieved cutting conditions and mechanical properties of the rocks. However, additional data is required to fill the data gaps and to potentially establish relationship between the brittleness index and all other parameters.

Jan 1, 2003

By T. Tholana

South Africa hosts some of the world?s largest known resources and reserves of minerals that are strategically important to the global economy. The country?s mining industry contributes significantly to the national economy in terms of gross domestic product, export earnings, corporate tax receipts, remuneration earnings, and employment. Platinum, gold, and coal are significant minerals because they make the largest individual contributions to these economic indicators. Several factors impact the cash cost performance of operations that mine these minerals, thus affecting the future sustainability of these operations, which are generally ?price-takers?. It is therefore important that the cash cost performance of operations for these key minerals is analysed. Commercially available industry cost curves can be used for such analysis. However, some companies may not be able to afford to purchase these curves. This paper presents a simple Microsoft Excel® algorithm for constructing the curves. It also demonstrates how the constructed industry curves were used to analyse the cash cost performance of South African mining operations for the three selected minerals for the period 2007 to 2011, which included the 2008 global financial crisis. The analysis revealed that the operations were affected by several global and local factors during the review period. The work reported in this paper is part of an MSc research study at the University of the Witwatersrand. Keywords cost curve algorithm, economies of scale, cash cost performance

Jun 1, 2013

By A. M. Hearn, J. R. Henning, A. S. J. Van Rensburg

The lining, together with the electrodes, forms the heart of the operation of a submerged arc furnace. Subsequent to a lining failure on M12 furnace during the early 1980s, Metalloys was active in investigating the concept of thermally efficient ?freeze? linings for its furnaces. The theory revolved around that, not only would, thermally efficient linings result in significant cost savings, but they would also last longer as a result of being subjected to less harsh operational conditions. After having proved the concept on the .smaller. furnaces, Metalloys decided to implement the concept on its largest submerged arc furnace, M12 Subsequent to having recovered from an impending failure of a lining installed in 1981 in M12 in the mid 1980s, Metalloys managed, through rigid lining management, to extend the life of this lining to 1999. At the end of 1999 the decision to replace the lining in the furnace with a ?freeze? lining was made and planning and design proceeded in earnest. This paper discusses the options considered in making the final decision. The features of the design of the lining are also discussed. Consideration is given to the furnace shell cooling system as a result of its importance in maintaining the thermal equilibrium in the lining. Note is made of the fact that the purchase of a .freeze. lining is an expensive exercise but that the time savings in the installation of the lining and the efficiency improvements during operation far outweigh the additional capital cost. The experience on M12 has been that the payback period of the marginal capital expenditure is less than three years. As a result of the opportunity to reline a furnace the size of M12 not presenting itself very often, the learning points from the installation of the lining and the operational advantages and disadvantages are significant. Finally, the point is made that the project had its pros and cons but overall the success of the project has been evident and, as such, the ?freeze? lining is likely to become the norm at Metalloys.

Jan 1, 2004

By W. Barnett

The Limpopo Metamorphic Belt is a complex geological terrane with at least three major deformational events. Tectonically juxtaposed lithology, open to isoclinal folding, crosscutting and re-activated shear zones and metamorphic gneisses and schists make pit slope design and maintenance a risky business. Venetia diamond mine?s Cut 3 is planned to reach 360 m by 2011. The difficult rockmass created problems in the original pit and a new more comprehensive slope design was necessary. Nearly 9 km of geotechnical drilling were undertaken to produce a new geological model and provide geotechnical information near the final Cut 3 face. All existing data from the pit were brought together into a database. SRK Consulting were brought into the project to audit the process and provide most of the manpower for the data analysis. Existing failures were back-analysed and the geotechnical domains identified. Analyses of only the southern domains are discussed in this paper. Geotechnical engineers can design slopes at any angle, but it is up to the managers at the mine to decide what risk they are willing to accept in a slope design. Once the issue of risk was discussed and settled in respect of the consequences of failure, each of the main geotechnical domains were analysed to produce a slope design at5% probability of failure with 15% above the first ramp. A risk assessment of the design was then undertaken to determine what risk the design placed on the equipment, personnel and the profitability of the overall mining operation. The risk assessment indicated minimal risk to the operation. One of the main assumptions of the final design is that the pit slopes will be dewatered. A project was immediately put in place to determine a groundwater model for the mine and to thereby determine the best dewatering procedure. However, it should be obvious that it is practically impossible to prevent benches from getting briefly saturated with water during storm conditions. It was therefore necessary to look specifically at supporting the crests of the ramps in the problematic southern domains to guard against the possibility of crest failure during heavy rains. The data available were re-analysed toward this objective. Spiles were recommended as the most cost-effective support system, and a probabilistic approach was used in the design. The final design has a 5% probability of failure, and the analyses indicate a strong sensitivity of the required spile spacing to the strength of the reinforcement material that will eventually be used. The pit slope parameters derived as per the discussion in this paper have just begun to be implemented at Venetia Mine.

Jan 1, 2001

By F. M. C. C. Vieira

The work described forms part of a Safety in Mines Research Advisory Committee (SIMRAC) funded project, currently an ongoing programme of research aimed at providing ?improved criteria, guidelines and the use of numerical models to design mine layouts at depth, so as to reduce seismicity and enhance worker safety?. The entire project deals with a number of distinct, albeit interrelated, research areas such as: subsidence and caving in hardrock, general numerical criteria for layout design, regional benefits of backfill, concrete pillars, strike stabilizing pillars and bracket pillars. This paper will focus on the last two items only. New considerations for the design of both stabilizing pillars and bracket pillar layouts are briefly discussed.

Jan 1, 1998

By G. S. Maré

Tin plating operations are of a complex nature due to the many operational variables that need to be controlled in order to create a product of required quality. The work in this report lays the basics for the control of a halogen plating operation based on the DuPont tinplating set-up with regard to the chemical make-up of the plating solution, as well as operational variables such as temperature and current density. To evaluate these aspects of the process, a rotating cathode Hull-cell set-up was used. This allowed for a laboratory scale plating arrangement that simulates industry closely with regard to chemical and hydro-dynamic considerations. Typical industry accepted standards were obtained for the values of operational variables and a ?baseline? test was conducted employing these standards. All subsequent tests conducted were benchmarked against this baseline result. A large suite of results was obtained in which it was found that changes could be made to the industry accepted norm which would improve on the stability of the operation and therefore the quality of the final tin-plated product. Examples of these results are: an increase in stannous tin concentration, an increase in sodium chloride concentration and a slightly elevated plating temperature. In addition, conditions were found that must be avoided to prevent instability and poor product quality.

Jan 1, 2010

By A. P. Squelch

The question of what stress condition exists in the hangingwall of tabular stopes remains topical and largely unanswered. Limited field data exist to quantify the situation and provide calibration for investigative computer modelling exercises. Work conducted in1989 and 1990 under a Chamber of Mines Research Organization (now the CSIR: Division of Mining Technology) programme of research into the behaviour and benefits of backfill may assist with this situation. The original work was motivated by the premise that the improved hangingwall stability in backfilled panels (identified by rockfall accident analyses) is due to a change in the hangingwall stress regime. Current, largely theoretical, studies into mechanisms of stope hangingwall behaviour and support interaction could benefit from considering these data. Keywords: Backfill, horizontal stress, stope hangingwall, hangingwall stability, support interaction.

Jan 1, 2002

By J. -W. Kim, Y. -B. Kang, H. -G. Lee

The effect of SiO2addition on the decomposition of Li2CO3was investigated at temperatures up to 1000ºC. It was found that addition of SiO2greatly enhanced the decomposition of Li2CO3. The main decomposition reaction started at around 600ºC, and completed just above the melting point of Li2CO3. The major decomposition product was Li2O?SiO2irrespective of the Li2CO3to SiO2mixing ratio while both reactants were available. It was ascertained that a liquid layer betweenLi2CO3and SiO2particles formed and facilitated the decomposition reaction. The governing reaction of the decomposition was the one between the dissolved Li2CO3and SiO2in the liquid layer to form Li2O?SiO2. The decomposition rate was independent of the Li2CO3/SiO2mixingratio until either one had been completely exhausted. When excess Li2CO3existed, it further reacted with the initial product of Li2O?SiO2to form 2Li2O?SiO2. When SiO2was found in excess, on the other hand, no further reaction took place. This is attributed to the fact that uponLi2CO3exhaustion there is no liquid phase available to facilitate further reaction. The apparent activation energy of the decomposition of Li2CO3in existence with SiO2is 198 kJ mol-1.

Jan 1, 2004