Search Documents

By M. Keevy, K. Hackney

Centrifugal slurry pump station and deposition sites are a common feature of many mines and mineral processing plants. Yanacocha Mine has completed the design of a pump station consisting of two trains of four pumps each. A number of trade-off studies was conducted to optimize the pump station design. The most significant of these was determining the drive types for the slurry pumps. The pump station duty can vary considerably due to the number of deposition points round the disposal site. The standard solution to this problem on a multi-stage pump train is to install one pump with a variable speed drive to control the pump station output by varying the speed of this pump and stopping and starting other stages. However, there are a number of negative impacts associated with this approach. These include head losses through pumps that are stationary or ?wind-milling?, different wear life on pumps that are running and pumps that are stationary, and slower response to the control system with the possibility of hunting. The use of variable speed drives on all the pumps was considered as an alternative to the standard solution. The factors considered in comparing these options were the control and operational differences, the pump efficiencies and absorbed power, the expected pump wear life, the impact on pump maintenance and the cost of the drive options. For this project the option of using all variable speed drives was selected. The paper presents the following aspects of the study: ?Description of the various options investigated. This includes a discussion on the required duty and the drive options. ?Technical comparison between the options. ?Description of the factors influencing pump performance and life.

Jan 1, 2007

By G. J. Kringe

The results of a series of measurements of accelerations and guide-roller loads made on mineshaft conveyances are given, together with the predictions of these accelerations and loads based on a computer programme. The analysis of the measurements is described, and the results of the measurements and computer predictions when compared show reasonable agreement. Some parameters that increase the guide-roller loads are identified, and their effects are studied, together with some comments on the total loads. Finally, a possible format for a design specification is discussed, and some tentative design values are given.

Jan 1, 1986

By A. B. Stewart, I. J. Barker

Traditionally it has commonly been believed that the only problem with inductive reactance in a submerged-arc furnace is that it leads to difficulties with the electricity supply as a result of the Iow power factor. This paper sets out to show that inductive reactance can also give rise to the following problems in the metallurgical operation of a furnace: (i) dead and live phases (fairly well known in openarc furnaces), (ii) lack of sensitivity to electrode movement, (iii) interactions between electrodes. These problems increase with increasing inductive reactance relative to resistance, and thus they increase with furnace size. Each of these effects is discussed in detail, and suggestions are made for their alleviation.

Jan 1, 1980

A. H. Mokken: I am pleased to have been given this opportunity to make a contribution to Dr Muller's paper tonight. The reason for this is that, at one stage in our careers, we were associates in the same undertaking. Dr Muller, then fresh from University, with a degree in pure science, had just stepped onto the first rung of the ladder, which, it was then thought, would lead him to a career in gold extractive metallurgy. However, endowed with an enquiring mind and conscious of a lack of fundamental training in general metallurgy and engineering, he felt a need for further academic study. To meet this need and, more importantly, to meet the necessary finances, he found his opportunity in steel. Armed with a bursary, he bade farewell to gold and proceeded overseas, to the University of Sheffield, to train as a steel metallurgist. The outcome of these academic efforts, which were followed by assignments in the steel industry and a further period at Sheffield, is the man we have listened to tonight-a highly qualified metallurgist who has displayed a sound knowledge of his subject. In choosing Sheffield, Dr Muller became associated with a steelmaking centre of world renown, a centre usually credited with the first systematic production of alloy steels, as far back as the 18th century. Since that time, great advances have been made in the production of alloy steels and this is especially so in the last decade or two, when major developments in civil, mechanical, electrical, aeronautical and nuclear engineering have been made possible by the development of steels with improved properties. In spite of spectacular advances in the technology of non-ferrous alloys, plastics and other materials of construction, steel has maintained its role as a pre-eminent material for engineering use. With the gradual accumulation of data on the properties of steels, and the use of thin film electron microscopy, to study the behaviour and characteristics of such phenomena as dislocations in metals and other microstructural features, the physical metallurgist appears to be approaching the stage of an exact understanding of such phenomena as strength, ductility and brittleness-a knowledge which could lead to close control of such properties and, therefore, to the attainment of the highest goals. An interesting example, illustrating the use of fundamental principles, based on physico-metallurgical research, is the development of the maraging steels developed by Bieber at the International Nickel Company. These steels have met the extreme technological requirements of the space age by providing the material for the cases of large rockets in which qualities, such as high tensile strength, toughness, workability and weldability are most important. Attractive as they might appear to be in considerations of savings of weight, cost of erection, transport of materials and foundations, the use of high strength steels has been accompanied by special problems such as brittle fracture, hydrogen embrittlement, notch-toughness and fatigue. It has been found that high strength steels, which performed acceptably in conventional tension tests, were found to undergo failure, in a brittle manner, in service. Hydrogen embrittlement has caused spectacular failures at a fraction of the normal ultimate tensile strength, and a lack of correlation between fatigue and tensile strengths has diminished the advantages to be obtained from the use of high strength steel in some applications. A new approach to the selection of materials for engineering design has resulted from a consideration of these phenomena in which strength, as such, is no longer as significant as it was previously. Parallel with the development of high strength steel has been the need for suitable techniques for joining component parts and here welding has played an

By J. H. Dalton

The paper reviews the effects of fast-neutron irradiation on the tensile properties of austenitic stainless steels at irradiation temperatures of less than 400°C, using, as an example, work carried out at Pelindaba on an AISI 316 type steel produced in South Africa. Damage produced in these steels at higher irradiation temperatures and fluences is also briefly discussed. The paper concludes with a discussion of some methods of overcoming or decreasing the effects of irradiation damage.

Jan 1, 1979

By G. L. du Plessis

This paper describes the design, installation and operation of an endless rope haulage system recently built for and commissioned at Evander Gold Mines in Mpumalanga, South Africa. The factors which lead to the choice of such a system and the advantages gained over more commonly used winding systems are outlined.

Sep 1, 2001

By M. Wu, X. Zhao

This paper presents an integrated pipeline transport system for thickened coal sludge, which combines pretreatment and pipeline transport with combustion techniques of thickened coal sludge. The pipeline can transport thickened coal sludge with a sufficiently high solids content (about72%?77%) and high apparent viscosity (about 1 000Pa?S?3,000 Pa?S) directly by pipeline having neither use for water nor an addition agent. The transport distance can be as high as 1 000 metres. In particular, the operating principles, key equipment and technical parameters of this integrated system are examined in this paper. The integrated system effectively causes no pollution to the environment because it is completely sealed, and conserves energy over traditional conveyer designs. Keywords: pipeline transport; integrated system; circulating fluidized bed boiler; thickened coal sludge; high solids content

Jan 1, 2007

By J. J. van Vuuren

Pipe-stick support in deep-level gold mines is first described and illustrated, a pipe-stick being a mine pole trimmed to the required size and sleeved by a pipe. An account is then given of an investigation into this form of support that involved load-compression tests in a 1000-ton press, tests in a rapid loading machine simulating rock-burst conditions, a study of the load-compression behaviour of pipesticks installed underground, and a cost evaluation. Pipe-stick support was found to be very effective on the face and to cost less than conventional matpacks.

Jan 1, 1979

By A. Koursaris, Y. N. Turan

This paper reports the results of a literature review carried out on nitrogen-alloyed austenitic stainless steels and their properties. It was found that a large volume of work has been carried out on the subject, particularly with regard to the more common stainless steels such as types 304 and 316. No work appears to have been conducted on the highly alloyed steels such as type 310S. Nitrogen has been found to increase the stability of the austenite in stainless steels and to impart significant improvements in the mechanical and corrosion properties of these alloys. Importantly, nitrogen appears to increase both the ductility and the strength of austenitic stainless steels over a wide range of temperatures.

Jan 1, 1993

By L. A. Vermeulen, D. D. Howat

Extensive work was done previously on the wear of grinding media and on the comminution processes operative in bal milling based on the determination of the number-size and mass-size distributions of samples of balls taken from bal mils by a specially designed device. Proof that a sample is as nearly representative as possible of the whole mass of material from which it is drawn is usually extremely difficult. This paper reports a special case in which a direct comparison was made between the number-size and mass-size distributions obtained from a sample drawn from a mil and those from the whole bal charge emptied from the mil. Exposure of the internal defects of the grinding balls caused them to develop irregular shapes after wear had reduced their diameters by about 50 per cent. As a result of the marked change in the morphology of the grinding components, an anomaly was observed between the proportion of small components collected by the sampler and that determined in the total charge. Except for this anomaly, a marked similarity was found in the data relating to the larger components in the sample and the total charge, indicating that the sample obtained by the procedure outlined is representative of the mass of the grinding charge in a mill.

Jan 1, 1989

By C. van Loggerenbergt, P. E. Ventert

A strong incentive exists for the coal-preparation engineer to improve plant efficiency by modifying circuits and upgrading process equipment, since these result in lower production costs and more valuable plant products. At the Grootegeluk Coal Mine, it was found that the overall plant efficiency could be improved by modifications to the dense-medium circuits, the installation of additional process equipment for the recovery of fine coal, and improvement of the fine-material processing circuit. Apart from these modifications, there is still potential to increase the plant efficiency, particularly in the utilization of plant waste, the recovery of slimes, and even the improvement of cycloning performance as a result of new cyclone design. This paper points to the potential wealth locked up in existing coal-preparation plants, and shows how the coal-preparation engineer, with new technology at his disposal, can unlock this wealth.

Jan 1, 1992

By G. T. van Rooyen

Materials for Winding Plant Components By Prof. G. T. van Rooyen (ScD) (MIT). Materials for critical applications such as winding plant components are reviewed in terms of the basic requirements which have to be complied with. It is shown that tensile testing alone is not sufficient and that impact testing also is necessary if the incidence of brittle fracture is to be avoided. As a criterion it is suggested that the brittle transition temperature (B.T.T.) determined by impact testing should in all cases be well below the lowest anticipated service temperature. A number of steels were evaluated by impact testing and it is shown that a small ferrite grain size, obtained either by chemical means such as by the use of appropriate alloying elements in the steel or by means of a quenching heat treatment, is effective in attaining a Iow B.T.T. The speed of strain aging as well as the influence of strain aging on the B.T.T. was also evaluated. On the basis of the results obtained it is recommended that steels for critical applications must conform to an appropriate grade and class of steel according to BS 4360 specification. It is further recommended that such steels be exempted from the customary six-monthly heat treatment prescribed by the Mines and Work Act, Regulation 16,18.

By H. W. Read

Sustained growth in demand for platinum group metals has resulted in an unfettered increase in new projects undertaken by the platinum producers. These projects are outsourced to various degrees. The argument of this paper is that both the client?s project manager and the consultant?s project manager are essential elements in the successful execution of a project. Their roles are not only different but also complementary, and are defined in the paper. Data gained from considerable experience in the South African corporate mining environment underpins the opinions expressed in the paper. Furthermore, an extensive literary search was undertaken to determine trends in related industries outside the South African context. Throughout the argument it is emphasized that project philosophy emanates from a systems view and must be treated as an overarching whole. The elements of project management become meaningless unless they are connected to one another and integrated into a cohesive unit. Advancing the knowledge field of project management is of critical importance to mining investors. There is no doubt that a key determinant of the sustainability of mining business is closely related to the efficiency of all-inclusive project management. From pre-investment and feasibility studies, implementation and execution, to ramping-up to full production, scientific project management has a critical role to play. Guidelines for the pursuance of this ideal are proposed. The introduction contextualizes the subject matter in an overview of the evolution of mine management in South Africa and abroad. Then, brief insight is given into the philosophy of project management. This exposition is confined to the predispositions, presuppositions and defining characteristics of project management. The core of the paper looks at the roles of the client?s project manager in relation to the consultant?s project manager. This section is underpinned by practical experience gained by the author on numerous mining projects. A view is taken of the future of project management in the mining industry. The conclusion summarizes the argument and aligns project management trends in the mining industry.

Jan 1, 2004

By D. A. Fenton

The structural design of large grinding mills, with reference to shell-mounted bearings by D. A. FENTON*, P. Eng. (Visitor) The paper outlines the advantages of shell-mounted grinding mills over mills having a conventional trunnionsupported shell. The growing use of larger mills in the past decade has led to a significant number of mechanical and structural failures, the most common being those at the junction of the head and the shell. Larger mill diameters favour the use of shell-mounted bearings. The elimination of castings, which have an inherent weakness to fracture, makes the shell-supported mill lighter and stronger than a conventional mill of the same shell thickness.

Jan 9, 1976

By A. Brodt, I. Mezhibovsky

The traditional vertical transportation systems deliver both gangue and useful mineral. The extraction of the desired minerals requires the construction of mineral processing and waste management plants, driving production costs, and often creating a negative environmental impact. The proposed technology is an integration of mineral processing within the transportation system. The mined rock is crushed and then loaded into a vertical lifting system filled with heavy media, with an intermediate density between the mineral and the waste rock. Driven by gravity separation, the desired mineral floats to the earth's surface, while the waste sinks. Delivered minerals and sunk waste is extracted from the heavy media and is then regenerated to a dry state. The useful mineral should be suitable for further use, and the waste used for backfilling. Remained residues of the heavy media may be recycled and reused in the vertical transportation system. Trials of the proposed process in a pilot format have confirmed economic and environmental advantages over traditional methods of transportation and mineral processing technologies. Keywords: Gravitational processes of mineral processing, separation in heavy media, vertical transportation to earth's surface by floating up

Jan 1, 2020

By J. Gilliland

The Grootegeluk coal-beneficiation plant was erected in the Waterberg coalfield, near Ellisras in the Transvaal, to supply Iscor's steelworks with a predetermined tonnage of coking coal in accordance with strict quality requirements. This plant has to handle a high tonnage of raw coal, which is not easy to beneficiate, in order to produce 1,82 X IQ6t of coal. Extensive tests were conducted on borehole cores and a mass sample of coal obtained from the area. These tests were carried out on a laboratory and pilot-plant scale, and were aimed at the establishment of the most effective beneficiation methods and the choice of suitable equipment. This led to the completion of a full set of design and manufacturing drawings that resulted in the project approach . described in this paper.

Jan 1, 1982

By P. K. Van Manen

Anglo Platinum's Polokwane Smelter is situated outside Polokwane, in the Limpopo Province of South Africa. Wet concentrate is received from various concentrators along the Eastern Bushveld Complex. Approximately 60% of the total concentrate received is from UG2 Reef, and 40% is from Merensky Reef. The concentrate is dried in two flash dryers, and smelted in a single 168 MVA furnace. A PGM-rich nickel-copper matte is cast, crushed and transported to Rustenburg for converting. The plant was commissioned in March 2003. The wet concentrate, containing 12-18% moisture, is weighed, sampled by one of two auger samplers, and off-loaded into a concentrate shed, either directly through a grizzly into a hopper, or onto the floor. From the shed the concentrate is conveyed to 12 concrete silos. Each of the two identical flash dryers can be fed from six silos. From the flash dryers concentrate is transported pneumatically to a 3 000-ton dry concentrate storage silo. The flash dryers are rated at a nominal 66 tph of dry concentrate at 14% moisture, while the furnace can smelt 90 tph of dry concentrate. Therefore both flash dryers are required to operate when the furnace runs at design throughput. Each flash dryer consists of a hot gas generator (HGG), a disintegrator and drying column, and a section for gas/solids separation. In the HGG, gas heated up to 700° C is produced from the combustion of coal peas in a fluidized sand bed. The hot gas and wet concentrate are introduced to the disintegrator at the bottom of the drying column. The disintegrator breaks up any lumps of concentrate, and throws the concentrate up into the drying column, where it travels co-currently with the hot gas. A fan draws the hot gas from the drying column and through the gas/solids separation section, which consists of three primary cyclones, a multiclone and a high-temperature bag house. The dry concentrate reports to a 450-ton dry concentrate storage bin. A portion of dry concentrate is recycled to the wet concentrate feed in a paddle mixer, so that concentrate that is too wet does not enter the disintegrator. The drying column outlet temperature is controlled at 120° C. Coal is received by road, screened for oversize and conveyed to a 400-ton concrete silo. From here it is pneumatically conveyed to a small feed bin at each of the HGG' s. The optimization work consists of process control improvements relating to the HGG outlet temperature, to control the drying column temperature during the ramp-up of the HGG outlet temperature and bag filters. Furthermore a heat balance is used to evaluate options to increase the instantaneous drying capacity of the existing equipment. The coal consumption derived from the heat balance is compared with the actual coal consumption. The purpose of the optimization work is to achieve an operating schedule for the flash dryers such that they operate simultaneously for as short time as possible. Most of the time one flash dryer should operate, allowing maintenance to be done on the other flash dryer, while drawing down the dry concentrate stock. Keywords: Anglo Platinum, Polokwane Smelter, pyrometallurgy, metallurgy, platinum, platinum group metals (PGM), base metals, flash drying, fluidized bed.

Jan 1, 2006

By F. van Heerden

The paper sketches the. management of the various phases in a cost-reimbursable, plus-fee contract. which is claimed to be the most flexible of all contracts. In this type of contract, the contractor is reimbursed for all the direct costs Incurred, plus a percentage fee to cover his profit (or overheads and profit). The client usually reserves the right to approve all drawings, equipment purchases. contract awards, technical specifications. project cheques and change orders.

Jan 1, 1982

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by the Council. Although the worldwide readership of the Journal results in a preference for papers in English, the Council treats papers in Afrikaans on an equal basis, but, to meet the needs of the majority of readers, an English summary of some 5OO to 750 words should be provided.

Jan 1, 1984

By P. Wiesner, H. –M. Stonner

A brief account is given of the influence of sulphuric acid and chloride ions during the recovery of uranium by solvent extraction, followed by a discussion of the settling behaviour of dispersions and models to represent that behaviour. The paper ends with a description of various methods for the recovery of solvent, which is lost in the solvent-extraction process by entrainment and adsorption on solids and by dissolution.

Jan 1, 1982