Search Documents

By J. Labuschagne

The primary factor contributing to the profitability of a platinum mine and its associated concentrator is the time taken from the first hoist of material from underground to the first batch of concentrate shipped. To minimize the time it would take to produce concentrate without stopping because of a lack of feed material a project was undertaken to integrate the mining model with a concentrator production schedule () in the most capital-effective manner. A secondary goal was to ensure detailed stockpiling requirements, as the concentrator is in an area where ?visual pollution? is to be avoided. To achieve this a dynamic stockpile model was created utilizing the mine production schedule resolved into a daily production figure. Four different concentrator development models were then proposed. The difference between the mine production and concentrator consumption was integrated over the life of the mine to provide the accumulated stockpile tonnages for both Merensky and UG2 ores. The stockpile levels were never allowed to fall below zero to prevent a situation where the concentrator was operational without feed material,. When a development option was selected, the standard metallurgical performance calculations were used to derive a concentrate production schedule, that was then used as a basis for commercial concentrate sale negotiations.

Jan 1, 2012

By S. Langea, H. Lieberwirth

Impact crushers are common machines in comminution plants. Their high size-reduction ratio and relatively simple design, make them a preferred tool even when subjected to harsh wear, and producing a large quantity of fines in some applications. Until now the alignment of the operational parameters was an operator’s responsibility. Due to the random process characteristic this is mostly done based on empirical values and sensor data, such as power consumption. This paper describes a new approach for online process monitoring of the horizontal-shaft-impact crusher. The application of robust, low-cost acceleration sensors enables the permanent observation of the process characteristics. The operational and evaluation methods are determined on the basis of experiments. Subsequently the recorded measurements are analysed in regards of throughput, rotational speed and product particle size distribution. Occurring signal characteristics are described based on physical and technical principles. The measured data of the acceleration sensors at varying operation conditions provide insight in the course of process. The accurate utilisation yields the determination of the preferential process conditions providing the best balance between the pros and cons of an impact crusher. Both the experimental method and the data processing is discussed from a scientific perspective, displaying a completely new approach for the operation of impact crushers. Keywords: Impact crusher, acceleration sensors, data processing, particle size

Jan 1, 2020

By W. D. Grimsley, R. P. King, J. B. See

Samples (15 to 20 g) of pre-calcined Mamatwan manganese ore or pure Mn 304 smaller than 48 mesh were reacted at temperatures in the range 1000 to 1300°C with samples of spectrographically pure graphite smaller than 325 mesh. Samples (1 g) of ore or pure Mn02 smaller than 48 mesh were reacted at temperatures of 1000 and 1200°C with pure graphite fines in argon, with graphite in carbon, .'1onoxide, and with carbon monoxide alone. In each case, the loss of mass as a function of time was recorded with a hermobalance. The rate and degree of reduction were found to increase with additions of carbon and with increasing temperature up to 1300oC, when they reached their maximum. The shape of the reduction curves, together with the results obtained from examination of the products of reaction by microscopy and X-ray diffraction, were used as the basis for a postulated reduction mechanism. Some details are given of an initial kinetic model that was used to verify the proposed mechanism. It was found that the reduction of Mamatwan ore by graphite at temperatures in the range 1000 to 1300°C occurs in two stages: (i) an initial stage during which the higher oxides of manganese are rapidly reduced to MnO with concurrent formation of CaMn2O4 and (ii) a longer stage during which CaMn2O4 and MnO are reduced to carbides by carbon dissolved in the ferromanganese phase.

Jan 1, 1978

By L. C. Stilwell

The paper will attempt to identify the threats, however obscure, that could confront the South African platinum industry. South Africa has the largest reserves of platinum group metals in the world, and is the largest producer of those metals. This situation is no different from that which existed in the gold sector fifty years ago. Since then South Africa?s share of world gold production has dwindled, and the gold mining industry has lost its dominance. Unlike gold, platinum has widespread use as an industrial commodity. Its investment value is a minor portion of its total value. It is therefore subject to different market forces. The sheer magnitude of the industry in South Africa obscures the fact that it is a wasting industry, and that South Africa exports almost all its production as a refined metal in the form of autocatalyst. Since Hotelling published his seminal work The economics of non-renewable resource in 1931,the science of mineral economics has developed exponentially. The paper will present a background of mineral economic theory and compare to this the development of the South African platinum industry. Of particular concern to a mineral exporting country is the question of mineral rent?its definition and employment. This will be the mail theme of the paper.

Jan 1, 2006

By R. W. O. Kersten

The South African Institute of Mining and Metallurgy collaboration with the Chamber of Mines of South Africa, arranged a colloquium to inform mine management of the current state of knowledge on the rockburst hazard associated with geological structures. The Colloquium was held at Mintek on 4th June, 1986, and attracted approximately 240 delegates.

Jan 1, 1986

By J. van der Walt, W. Spiteri

Flyrock remains a significant threat to the health and safety of mine employees and integrity of infrastructure, as well as to the safety of the neighbouring communities and their property. This investigation was motivated by the general lack of fundamental research and mathematically quantifiable data in the literature regarding the relationship between blast design parameters and their impact on flyrock. The focus was to develop a concept that can be used to mathematically quantify the trajectory of flyrock resulting from a blast, which can be used for future research. The ultimate goal for this technique, once it has been fully developed, is to: ➤ Enable mining operations to generate a database with accurate historical flyrock measurements resulting from their blasting operations ➤ Allow research teams to conduct scientific investigations into flyrock and the impact of various blast design parameters ➤ Generate point-cloud data to visualize blasts and flyrock in a virtual reality environment for training and education purposes. This paper summarizes a conceptual technique and preliminary fieldwork that was carried out to determine the technique’s feasibility and motivate further development. The results show conclusively that a modified photogrammetric technique is capable of capturing flyrock data for further processing and analysis. The data acquisition procedure can, at this point, be used to meet the first aim of the project, namely to gather a field database of historical flyrock generation. Further development of the technique is ongoing and it is envisioned that the scientific-based technique will provide a method whereby future flyrock studies will be comparable and that assumptions will be limited.

Apr 5, 2023

By D. H. C. Griffiths, D. R. Davis, D. B. Paterson

Consolidated Murchison Limited is the only primary producer of antimony in South Africa, producing approximately 18 per cent of the total world production. This paper gives a technical review of the history, occurrence, mining, and metallurgy of antimony at Consolidated Murchison. World antimony markets are also discussed, together with the end-uses.

Jan 1, 1986

By E. Kuipa, J. N. Lekunze

The selection of an underground mining method stems from a multivariate analysis that considers geomechanical, geological, economic, and operational parameters. Even after identifying the most compatible method, there is no assurance that the mining company will achieve the best performance. The geological complexity of some deposits requires adaptations of methods described in the literature to obtain more selectivity and reduce mining waste. There are some studies on geometry of underground structures, but a methodology that describes an adaptation of a room-and-pillar mining method for ore bodies with down-dip varying from 20° to 25° is novel. The present work aimed to reduce dilution by adapting the traditional room-and-pillar mining method (TRP) to inclined ore boLittle attention has been paid to the rehabilitation of derelict and ownerless mines in South Africa after their lifespan. This paper aims to explore management gaps in legislation that have resulted in the non-rehabilitation of derelict and ownerless mines in South Africa. There is growing evidence that supports the distressing effects of mining on people living around these mines in the North West Province. This paper was motivated by the current socio-economic status quo of old mining towns, the influx of illegal miners (Zama Zamas), severe environmental damages, and the violence associated with derelict mines. Underpinning this research was an ecosystem approach and integrated resources management principles, which formed the foundation for the decision-making process.The researcher used a mixed-method approach and employed convergent techniques. A semi-structured instrument was used to collect data from 200 respondents. The results indicated that there is a dire need for community-based consultative processes, and an absence of clear guidelines for derelict and ownerless mines to pressure mine management to adhere to rehabilitation standards. Moreover, the mining charter is ambiguous regarding policy implementation, budgetary allocation, and duration of the rehabilitation of these mines. The paper concluded that management challenges associated with derelict mines can be reduced if all stakeholders follow the guidelines as outlined in the environmental legislative framework (NEMA) of South Africa while being open to innovations in line with international best practices. It also contributes towards the development of guidelines for the management and implementation of legislation related to derelict and ownerless mines in South Africa from a philosophical, theoretical, and policy perspectivedies. This new method is entitled short-hole room-and-pillar (SHRP). The equations that measure the dilution are defined according to the geometry of stopes and openings. The results comprise comparative analyses of the operational and planned dilutions to measure the performance of the SHRP method. The average operating dilution of the SHRP method was more than five times lower than the planned dilution according to the TRP method. Low operational dilution indicates high selectivity of the method and its potential to reduce underground mining tailings.

Oct 9, 2024

By J. Svoboda, W. J. C. Venter, R. N. Guest

SYNOPSIS Wet high-intensity magnetic separation was examined as a method for the recovery of copper and lead from Tsumeb flotation tailings. Bench-scale and pilot-plant tests were conducted and, despite the very low magnetic susceptibilities of all the complex copper and lead minerals, copper and lead recoveries of over 60 per cent and almost 50 per cent respectively were obtained at a combined copper and lead grade of up to 13,5 per cent. The recoveries were found to be practically independent of magnetic induction in the range 0,5 to 2,2 T, and the grade of the magnetic concentrate decreased with increasing magnetic induction. The grade of the magnetic concen¬trate improved when the flowrate of the slurry was increased, and desliming was found to have a profound effect on the. metallurgical process. Particles smaller than 10 µm were not recovered, and their presence in inefficiently deslimed samples impaired the overall performance of the magnetic separation

Jan 1, 1988

By P. Lundman, L. Rosengren, T. Brandshaug

Tunnel 99’, the Swedish National Road Administration´s (SNRA) general technical specification for road tunnels requires that the load bearing system must be designed to withstand specified design explosion loads. This paper presents the results of an SNRA study to provide a perspective of design analyses tailored to comply with the new requirement. The paper provides an example of a design analysis for assumed tunnel conditions using a numerical model. Dynamic predictions of potential damage to the rock mass and ground support system (rock bolts and shotcrete) from the specified explosion loads are presented including the nonlinear response of the shotcrete. “Tunnel 99”, qui fixe les règles de l’Administration nationale suédoise des Routes (Vägverket) concernant la conception et la construction des tunnels routiers, requiert entre autres que la structure porteuse soit capable de résister à certaines contraintes spécifiques résultant d’explosions. Cette étude présente les résultats d’une étude effectuée par Vägverket en vue d’obtenir une perspective d’analyses de conception spécialement élaborées pour se conformer aux nouvelles règles. Il contient un exemple d’analyse en fonction de conditions déterminées, basée sur un modèle numérique. Des prévisions de’études dynamiques de dommages potentiels subis par la masse rocheuse et les systèmes de soutènement (boulons d’ancrage et béton projeté) du fait des contraintes libérées par la force d’explosion spécifiée sont également présentées, y compris dans le cas d’une réaction non linéaire du revêtement en béton. “Tunnel 99” - die Vorschriften für Strassentunnel der Nationalen Schwedischen Behörde für Straßenwesen - (Vägverket) - fordern vom Tragsystem eine Auslegung in der Form, dass es spezifischen Explosionsbelastungen standhält. Dieser Artikel präsentiert die Ergebnisse einer Studie der Behörde, um einen Ausblick über konstruktive Auslegungen zu geben, die geeignet sind, die neuen Vorschriften zu erfüllen. Der Artikel zeigt ein Beispiel einer konstruktive Auslegung für eine angenommene Tunnelsituation mit Hilfe eines numerischen Modells. Voraussagen unter Beachtung der vollständigen dynamischen Berechnung zu potentiellen Schädigungen des Gebirges und des Ausbaus (Anker und Spritzbetonauskleidung) durch die spezifizierten Explosionsbelastungen, einschließlich des nichtlinearen Verhaltens der Spritzbetonauskleidung, werden gezeigt.

Jan 1, 2003

By E. L. Atkinson, G. W. Leach

The paper discusses the reasons for the introduction of load-haul-dump (LHD) units into Greenside Colliery, and the circumstances leading to the replacement of conventional mechanized equipment on a trial basis in the mining operations on No. 2, 4, and 5 seams. An outline is given of the factors governing the selection and introduction of these units into coal mining, and the associated mining and engineering aspects involved in the optimization of their use. Operating statistics comparing the performance of conventional and LHD equipment are included.

Jan 1, 1979

By Nicolle Krusberski

Potential errors in XRF analysis are discussed and investigated with specific reference to the analysis of ilmenite samples. A selection of ilmenite samples was chosen and prepared using two XRF preparation techniques: pressed powder pellet and unroasted fusion bead. The merits of the two methods have been discussed in this paper for ilmenite analysis by XRF. Recommendations have been made regarding the use of pressed powder pellets especially with regard to the mineralogical effects that were evidenced during this investigation. The fusion bead technique was found to be far more accurate and able to meet short turnaround requirements provided the calibration methodology used is specific to the grade of samples analyzed.

Jan 1, 2014

By Deur T. A. M. Saayman

Die sesde jaarlikse Ingenieursimposium is in September by YSKOR, Vanderbijlpark gehou. Rierdie simposium, wat deur Ingenieurs-in-Opleiding georganiseer word, bied aan die Ingenieurs-in-Opleiding die geleentheid om referate te lewer oor projekte wat gedurende hul drie jaar opleidingsperiode uitgevoer word. Continuing education courses The following courses are to be given in the near future in The Netherlands. Coal trade, transportation, and handling . The 4th Coal Trade, Transportation and Handling Conference and Exhibition, CoalTrans '86, will take place the Rai Congress Centre, Amsterdam, from 10th to 12th June, 1986.

Jan 1, 1986

By L. Thomas, D. Muteba, L. I. Nsenga, B. Mbao, G. Longo Banza

Owing to the high ore grades in the African Copperbelt and variable acid consumption, agitated leaching is common practice and is used more widely in Africa than in other regions. Two common challenges for agitated leach–solvent extraction circuits are higher presence of colloidal silica in the pregnant leach solution and elevated levels of total suspended solids. Both can negatively affect the physical and metallurgical performance of the solvent-extraction circuit, and lead to higher processing costs or reduced copper production. Operating in organic continuity is preferred to address such challenges, but is not always possible: additional treatment options may be advantageous. For this reason, Solvay recently introduced ACORGA® CR60LT, a new chemical additive to address these concerns. Continuous addition to the pregnant leach solution improves physical performance without negatively affecting Cu transfer or cathode quality. Results and benefits from commercial utilization of ACORGA® CR60LT at different operations in the Copperbelt are reviewed

Jan 1, 2023

By L. D. Robbins, M. L. Murphy, A. C. Campbell, L. Murphy

This paper reports on what appears to be the first discovery of prehistoric mica-schist mining in southern 4frica. The mine concerned was found in a location very rich in rock art that is one of the most important archaeological sites in the Kalahari. The authors conclude that the oval pieces of mica schist that were found at the mine site were used by Khoisan peoples to scrape fatty tissue from hides that were to be cured. Radiocarbon datings seem to indicate that such ovals were used for at least 20 000 years.

Jan 1, 1994

By I. Nolet

Matte tapping is one of the most critical operations of a matte smelter. Every smelter has developed particular matte tapping practices and tap-hole repair strategies that are often based on the experience of the smelter personnel. As a result, very little information has been published on these critical topics. This paper aims at providing the information gathered from a survey conducted in the PGM and Ni industries on matte tapping practices and tap-hole maintenance strategies for different PGM-Ni matte smelting operations.

Jan 1, 2014

"Chairman: Dr W. S. RAPSON Rapporteur: Mr J. W. WILSONPapers:Computer applications in rock mechanics by F. H. Deist, E. Georgiadis and J. P. E. Moris Rock mechanics in the design of mine layouts by K. Hodgson and N. G. W. Cook Automated regulation of mine ventilation by P. NiskanenThe rock mechanics papers, because of their complementary nature, were presented in succession and discussion on both followed directly. The paper on automated ventilation control at a mine in Finland was then presented and the session was closed with several contributions to this paper.By and large the papers and discussions which followed in this session showed how a classic tie-up had developed between the use of computing techniques in important fields of mining, and their practical application. In fact, the dis-cussion following the rock mechanics papers showed clearly that without the aid of high-speed digital computers the rate of progress in applied research in deep-level hard-rock mines, would have been severely hindered. Furthermore, it became apparent from the comments made by several contributors that the rock mechanics techniques and computer progress described in Deist's and Cook's papers could be used to provide useful data in the solving of rock mechanics and design problems on mines other than flat dipping deep tabular deposits.The paper by Niskanen, which described an automated ventilation control system at a mine in Finland, showed how effective computers could be in areas where the reversal of mine ventilation occurs due to severe seasonal temperature ranges. Although the system described in the paper could not be introduced easily in complex underground mines, several contributors gave examples of similar ventilation problems that could be solved mechanically,In introducing his paper, Dr Deist said that the purpose of the paper was to give a brief account of some of the programs designed by himself and his co-authors to aid in the solution of rock mechanics problems,The first system presented by Dr Deist was known as MINSIM in the South African mining circles. This system was designed specifically to aid in the solution of rock mechanics problems in the South African gold mining industry. It was particularly designed to handle tabular deposits at great depth but it has been used satisfactorily on a number of occasions to obtain at least approximate solutions in other mining situations. Dr Deist said that the principles embodied in the programs were easily extended and, in fact, there was a project in progress at that time which was aimed to do this. He said that the principles could easily be extended to shallow-depth mining at steep or very steep inclinations."

Jan 1, 2014

Advances in extractive metallurgy, 1977. Proceedings of the third symposium organised by the Institution of Mining and Metallurgy held from 18-20th April 1977. London, the Institution of Mining and Metallurgy, 1977. 244 pp. £18,50. Coal preparation A meeting of the Organising Committee of the Eighth International Coal Preparation Congress took place in Moscow on 24th and 25th May, 1977. Representatives NIM reports Report no. 1906 An automated instrument for measuring the effects of impurities on cathodic-current efficiency during the electrowinning of zinc. (2nd Sep., 1977). Report no. 1908 An analysis of the replies to a questionnaire on materials of construction for ore hoppers. (16th Sep., 1977). Report no. 1913 The mechanism and rate of reduction of Mamatwan manganese-ore fines by carbon. (2nd Sep., 1977). Report no. 1914 The thermodynamics of the formation of sulphate complexes of iron (111), cobalt (11), iron (11), manganese (11), and copper (11) in perchlorate medium. (15th Sep., 1977). Report no. 1924 The composition of chromite grains from varwUB Witwatersrand reefs. (23rd Sep., 1977). Atomic absorption The Perkin-Elmer Corporation of South Africa is planning to hold an Atomic Absorption Autumn School in Cape Town from 10th to 13th April, 1978. Travel bursaries Two Atlas Cop co travel bursaries for study tours of Swedish mines may be awarded annually to young mining graduates. Stability in coal mining The First International Symposium on the above subject is to be held in Vancouver (Canada) on 5th to 7th April, 1978.

Jan 1, 1978

By D. Botha, J. F. Cronjé

"SynopsisAlthough women all over the world have been involved in mining activities for centuries, mining has always been considered a very masculine industry due to its heavily male-dominated workforce as well as the physicality of mining work. The mining industry has not been an obvious career choice and preferred place of employment for women; women were mainly employed in administrative and advisory positions. Until 1994, women were legislatively prohibited from being employed in underground operations in South Africa, but the Mines Health and Safety Act, No. 29 of 1996, removed these restrictions. In addition, new mining legislation (the Mineral and Petroleum Resources Development Act, No. 28 of 2002) and the accompanying Mining Charter make specific provisions for the inclusion of women in core mining activities and require 10% of core positions to be filled by women.This article voices perceptions of the physical ability of women employed in core mining positions. Findings are drawn from empirical work undertaken at platinum, phosphate, and copper mines. Quantitative and qualitative research paradigms are used. It is evident that women find it extremely difficult to perform mine work that requires physical strength and stamina. Practical recommendations, informed by the literature review and empirical findings, are made with the objective of contributing to the sustainable deployment of women in the mining industry.IntroductionFor many years, mining has been considered the foundation of the South African economy. Although the mining industry in South Africa is currently under considerable pressure and experiences various challenges, including escalating operational costs, electricity tariff increases, safety-related issues and associated production stoppages, poor productivity, labour unrest, and reduced demand both globally and domestically, it remains a key contributor to the national economy and development of the country (IDC, 2013, p. 9).Until 1994, women were legislatively prohibited from meaningful participation in the mining industry and were denied access to skills and jobs, self-employment, and entrepreneurship. The newly elected democratic government in 1994 initiated substantial socio-political and economic transformation in South Africa. Nearly every sector in the country was transformed and re-shaped, primarily through sector-specific legislation, but also through negotiations between government, industry, and labour unions to create and refine the so-called sector charters, which included the Mining Charter. The vision of the new regime, the African National Congress (ANC), was to ‘transfer power to the people and transform society into a non-racial, non-sexist, united, democratic one, and change the manner in which wealth is shared, in order to benefit all the people’ (ANC, 2007)."

Jan 1, 2015

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers, no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publication Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. Orthodox sequence Title and author's name, with author's degrees, titles, position. Synopsis. Index, only if paper is long and involved. Introduction, including a brief statement of conclusion. Development of the main substance. Conclusions, in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors & Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent that an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol % is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systemé International d'Unites (S.I.) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramme metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .1 . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publication of technical notes taking up to three pages (maximum 3 000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute as a body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there is full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organisations as well as to the Institute.