Search Documents

By H. W. J. P. Neomagus, J. R. Bunt, T. S. Mthombo, C. A. Strydom

"Low-cost calcium lignosulphonate (CL), which is a byproduct of the wood pulping industry, was investigated as a potential binder during laboratoryscale pelletization of inertinite-rich high-ash coal fines from the Highveld Coalfield of South Africa. Coal-binder mixtures containing between 1 and 15% calcium lignosulphonate were prepared, pressed, and ultimate, proximate, porosity, XRD, and XRF analyses obtained. It was found that increased pressure during pelletization results in increased attractive forces, due to increased interparticle contact areas. FTIR analysis showed that chemical interactions occur between coal fines and the binder, as evidenced by the formation of new C-O ether-type bonds. The presence of moisture during pelletization enhanced surfactant activity of the binder. Chemical interactions between the coal and the binder seem to be mainly electrostatic, driven by Ca2+ from the calcium lignosulphonate, which may act as a bridge between the anionic parts of the binder and the surface of the coal. IntroductionCoal has over the years remained South Africa’s major energy source, with over 90% of the country’s electricity being produced via coal-fired processes (Arndt et al., 2016). Sasol’s coal conversion technology alone provides more than 40% of South Africa’s liquid fuel requirements (van Dyk, Keyser, and Coertzen, 2006). The production of high-grade coal requires the processing of run-of-mine (ROM) resources by a combination of processes which include crushing, screening, and washing (Radloff, Kirsten, and Anderson, 2003). These processes result in the generation of coal fines (< 0.5 mm) which, until recently, have been discarded into slimes dams (le Roux, Campbell, and Smit, 2012). Several issues are associated with slimes dams, among which are the costs of transportation of these fines from the place of origin to the discard point (often a considerable distance), and the potential environmental effects due to seepage of toxic materials into surrounding ecosystems (Clausen, 1973).Consequently, utilization of these coal fines is an area of great interest. Mechanical densification of fine coal by means of pelletization and/or briquetting to larger sizes for use in technologies that require lump coal, such as chain-grate stokers and fixed-bed gasifiers, has been shown not only to reduce environmental risks (Mangena et al., 2004), but also to significantly reduce storage and transportation costs (Mani et al., 2001). Pelletization is the process by which solid particles are consolidated into uniform, usually hard, impact-resistant agglomerates, rendering them useful as a fuel with sufficient calorific value for domestic and industrial utilization (Finney, Sharifi, and Swithenbank, 2009)."

Dec 1, 2018

By P Clive Hart

DRA - BACKGROUND [MULTI MINERAL DESIGN & BUILD COMPANY FOUNDED 1984 ENGINEERING FOCUSED CORE ENGINEERING DISCIPLINES INCLUDE: ?PROCESS ?MECHANICAL ?E&I CONTROL PRIVATE COMPANY, INDEPENDENT & INTERNATIONAL]

Jan 1, 2006

By F. Wang, P. Rosario, A. Vazirizadeh

Advances in data science, machine learning, and artificial intelligence are transforming mining and mineral processing, and making them more algorithm intensive. The paradigm is shifting from one of detection and control to one of prediction and optimisation. To build up reliable prediction and optimisation models these steps should be passed: collect, aggregate, cleanse, and process large amounts of complex, structured, and unstructured data as a first stage. Next, the right tools must be used to extract meaningful features from the operational data for the build-up of a prediction model. A grinding circuit is one of the challenging areas in terms of determining its overall efficiency and the prediction of product quality. In a processing plant, some of the KPIs are typically unmeasurable or infrequently measured for real-time application, e.g. ore grindability and grind size. However, these variables are required to calculate the grinding circuit efficiency and to model the operation performance. In this paper, advanced analytic tools have been used to extract one selected KPI (cyclone overall P80 or final grind size) and its relationship with measured variables for an industrial dataset. The results illustrate that the performance of the grinding circuit can be predicted for real-time monitoring by means of measured data. Keywords: Grinding circuit, data-driven, machine learning, process modelling, hybrid modelling

Jan 1, 2020

By B. P. Watson

The discussion written by Dr de Frey suggests that mine design should be based on closely spaced stability pillars. However, this concept leads to low extraction ratios at depth. The concept of `crush&apos; pillars in conjunction with more widely, appropriately spaced stability pillars allows for significantly larger extraction ratios, particularly at depth. It should be noted that the rock conditions in many areas of South African platinum and gold mines are good, allowing significant spans to be mined safely between stability pillars. `Crush&apos; pillars are cut small enough to fail stably near the face under stiff loading conditions, and their residual strength is intended to support about 10 m rock height between stability pillars. While this support resistance cannot be achieved by conventional support, crush pillars have been proven to have the required capacity for this purpose. The concept of leaving smaller crush pillars with appropriately positioned stability pillars has been used successfully for more than 30 years in areas of South African platinum and gold mines.

Jan 1, 2011

By J. P. Gouvea

Back-analysis of two mining-induced tremors in 2011 was used to determine a modelling criterion for the entire Klerksdorp Goldfield (i.e., Vaal Reefs region). At that time, most mining operations in the region were owned by AngloGold Ashanti (AGA) and shared many geotechnical similarities. By 2018 AGA had sold off all its Klerksdorp operations to different mining companies, which continued applying the 2011 modelling criterion. As mining activities became more remote, scattered, and isolated, the extraction of isolated blocks of ground and remnants became increasingly necessary. However, the inherited criterion allowed only minimal or no mining activities at these areas. Keeping in mind that safety is the overriding consideration, an innovative numerical modelling approach, which includes the application of peak particle velocity designs, was developed to provide practitioners in the Klerksdorp Goldfield with a suitable criterion to justifiably and safely mine isolated blocks of ground and remnants. This would not always be possible if a conformist approach was used.

Mar 14, 2024

By J. Pelders, G. Nelson

"Fatigue is a significant concern in the mining industry as it is a causal or contributing factor in many incidents and accidents. Fatigue can be caused by work- and non-work-related factors. There is a lack of information about associations between demographic and other non-work factors, and fatigue. This study aimed to assess associations between demographic, work, living, and socioeconomic conditions, and lifestyle characteristics, and fatigue at a platinum smelter in South Africa. Eight interviews with management and two focus groups with production workers were conducted, and 75 questionnaires were completed by production and other workers. Both work- and non-work-related factors were considered to be causes of fatigue. These factors included overtime, shift work, high workloads, activities performed outside of work, age, race, housing tenure, diet, sleep disorders, stress, and job satisfaction. In general, higher levels of fatigue were reported by younger participants, those who rented accommodation, ate less healthily, had a sleep disorder, and those with high levels of stress and low job satisfaction. As various demographic, lifestyle, and wellness-related factors were associated with fatigue, both work and non-work contributors should be addressed in fatigue management plans. BackgroundFatigue may be defined as ‘a state of impaired mental and/or physical performance and lowered alertness arising as a result of, or a combination of, hard physical and mental work, health and psychosocial factors or inadequate restorative sleep’ (BHP Billiton, 2005). Williamson et al. (2011) define fatigue as a biological drive for recuperative rest. Sleepiness and fatigue are related, and the terms are often used interchangeably. However, sleepiness, more specifically, can be defined as sleep propensity, or a person’s tendency to fall asleep (Hossain et al., 2003; Shen, Barbera, and Shapiro, 2006).Increasing levels of fatigue and sleepiness are associated with lapses in attention, errors, response slowing, fluctuations in alertness and effort, and impaired attention, working memory, long-term memory, decision-making, and creativity (Alhola and Polo-Kantola, 2007; van Dongen and Dinges, 2000). Fatigue is also associated with adverse effects on mood and impulsive behaviours (Alhola and Polo- Kantola, 2007; Minkel et al., 2011; Schwarz et al., 2013). It is a significant concern in the mining industry as it is commonly identified as a causal or contributing factor in many accidents and injuries (Schutte, 2009). Fatigue can also lead to long-term health problems, including digestive problems, heart disease, stress, and mental illness (Shaw, 2003)."

Mar 1, 2019

By T. Matlou, S. Myendeki, V. Midzi, T. Zulu, H. Mabotja, T. Mulabisana, B. S. Zulu, L. Hlatshwayo, T. Makhateng

The Council for Geoscience (CGS) performed a macroseismic investigation following the occurrence of an earthquake in the Boksburg area on 11 June 2023. The event had a magnitude of ML 4.4 and a focal mechanism that showed the event as having strike-slip motion along a northwest-southeast oriented fault. The event resulted in aftershocks, some of which occurred away from the causative fault in the east in an area without a mapped fault. However, the cluster of past events in that area suggests that there is an active fault. Due to the size of the main earthquake, a macroseismic survey was conducted to determine its impact on the community in the region. Analysis of observed data obtained from questionnaires resulted in the creation of 153 intensity data points. Their distribution showed high intensity values close to the earthquake source area. However, the investigation highlighted a number of anomalies, such as the higher than expected intensity values observed far from the event epicentre. It could be that these anomalies are caused by site conditions, for example, amplification of ground motion due to thick soil layers.

Jan 12, 2025

By J. E. Dickinson, J. L. Sutherland, J. Zhou, M. J. Cole, K. P. Galvin

Interest in early gangue rejection has grown substantially in the minerals industry to reduce energy and water consumption arising from excessive comminution. Recent developments in coarse-particle flotation have proven successful by promoting a quiescent hydrodynamic environment to limit particlebubble detachment and by helping to convey more buoyant particles to the overflow. Current approaches also benefit from upstream classification to remove the finer particles ahead of the coarse-particle flotation. In this study, coarse-particle flotation was investigated experimentally using a novel hybrid gravity-flotation system called CoarseAIR™ that exploits the hydrodynamic advantages of the Reflux® Classifier. The system consists of a lower fluidised bed housing, with a system of inclined channels above. The inclined channels enhance the segregation and hence rejection of intermediate through to relatively coarse particles containing little or no surface liberation. This approach overcomes the need for pre-classification, while offering strong transport of coarse particles made buoyant through their attachment to air bubbles. The paper explores the strong relationship between the solids transport to the overflow and the input gas flux, showing firstly the potential for significant mass rejection at the relatively low gas fluxes, and robust performance in terms of recovery across the full range of gas fluxes. Keywords: Flotation, inclined channels, coarse particle flotation, Reflux Classifier

Jan 1, 2020

By L. Rojas Mendoza, F. J. Hrach, A. Gupta, K. P. Flynn

ST Equipment & Technology (STET)’s tribo-electrostatic belt separator technology allows for the beneficiation of fine mineral powders by means of an entirely water-free technology with high throughput and low energy consumption. The STET separator is suited for separation of very fine (<1 μm) to moderately coarse (500 μm) particles, in contrast to other electrostatic processes that are typically limited to particles >75 μm in size. STET has performed exploratory studies with several iron ores including tailings and experimental results to date have demonstrated that low-grade iron fines can be upgraded by means of STET tribo-electrostatic separator to commercial grades (58-65%Fe). Experimental results together with high-level economic evaluations indicate that scavenging processes involving low drying costs, DSO operations and tailings beneficiation offer a commercially viable processing method to recover fine iron that would otherwise be lost by traditional processing. Dry electrostatic processing of iron ore presents a clean, low-energy opportunity for iron producers to reduce costs and wet tailings generation associated with traditional gravimetric, flotation and wet magnetic separation circuits. Moreover, STET technology allows for mining waste utilisation and resource recovery from iron ore fines and tailings, therefore offering processors a novel method to recover fines that would otherwise be difficult to process to sellable grades with existing technologies. Keywords: Iron fines, industrial minerals, dry separation, calcium carbonate, talc, barite, quartz, tribo-electrostatic charging, belt separator, fly ash

Jan 1, 2020

By G. R. Lane

A large opencast gold mining company in Africa had just completed a feasibility study for the expansion of the operations. A traditional net present value project valuation methodology had been used that showed a very positive net present value (NPV). The project team had conducted a qualitative risk assessment that identified and logged all potential project risks and had subjectively incorporated ?risk? via the discount rate and other assumption contingencies around gold price expectations, operating parameters etc. Management requested that an independent quantitative risk modelling approach be adopted to obtain a better understanding of the impact of risk on the overall project valuation and confidence level in the final valuation. A detailed project valuation model was configured in the Carbon Modelling Technology and the stochastic modelling module used to perform the Monte Carlo simulations. Analysis of historical operational performance data relating to actual achievements versus planned and budget determined the historical variability of the underlying parameters as well as variance to budget. This was done at a detailed level for mining rates and costs, processing rate, costs and recovery, and other operational efficiency measures. External market assumptions relating to gold price, exchange rate, and inflation were modelled and the dependency between them modelled using a copula. This case study will demonstrate the approach taken to building and populating the quantitative risk model and the overall results of the Monte Carlo simulation. The final valuation demonstrated that the project had a 44 percent probability of an NPV less than zero i.e. 44 percent chance of project finance loss.

Jan 1, 2012

By J. P. Garnier, T. Bhambhani, J. A. Garcia, N. Renaud

Most flotation plants use a static reagent scheme, i.e., a set combination of collectors, frothers, and modifiers. This scheme is usually developed and refined over time to deliver optimal (not necessarily the highest) performance when the major ore types are fed to the plant. However, when ore types or mineralogy coming to the plant change substantially (and this often happens as different areas of the pit(s) are mined and crushed at the same time), there are upsets in the process, typically leading to lower recoveries. Adapting to this variability is usually done only when performance drastically suffers, and the changes made may be too late and bring additional variability in performance. The premise for SmartFloat™ is that the reagent suite needs to be dynamic, adapting continuously to changes in the ore and operating conditions. Solvay has combined advanced analytics and data science techniques with its expertise in flotation reagent chemistry to systematically and automatically achieve the above, and in real time. Thus, SmartFloat™ is optimizing the reagent suite continuously, removing the additional variability created by belated human interactions resulting in a better and more stable process. In addition, this advanced approach allows for continuous improvement by identifying poor performing ore domains and improving the reagent suite using Solvay’s FM-100 approach to design appropriate solutions.

Jan 1, 2023

By R. R. M. Cousens, W. S. Garrett

Discussion: L. T. Campbell Pitt: When Mr Garrett and I discussed the design and construction of plugs and bulk head doors to resist great water pressures in mines about ten years ago, we visualized an emeregeny when there would be no time for site preparation. We could not however, anticipate a problem of such magnitude and urgency as the one described in the paper under discussion. The paper very clearly describes the flooding and the measures taken to save the mine. The complete flooding would have been a national disaster. The account of the combat between man and water reads like the account of a military operation. It was an endeavour which achieved success because there was a master plan, tenacity and, in fact, heroism. The paper is of necessity a long one. In my contribution I will mention some historical facts and factors that I believe have relevance to the flooding and the saving of the mine. It is of great satisfaction to me to have been one of the two initiators of a new approach to underground plug design and construction. The investigation was taken over by a Chamber of Mines Committee which combined our early work with further research and the resulting data had a significant bearing on the West Drie emergency plug designs. The final plug length was correctly based on the requirements to obviate leakage. A plug to have structural strength only would have been very much shorter but so ineffective as to have become a waste of labour, material, and in consequence, wasted the limited time available to prevent flooding of the whole mine. The figure of 75 lb per sq in. sheer stress provided a very ample margin, in my opinion, but under the very difficult site conditions and the limitations of plug material suitable for the very unusual construction, justified such a figure. There must have been considerable temptation to reduce the safety margin due to the urgency to complete and commission the plugs, but it is much to the credit of the directors of this operation that nothing less than a safe design was permitted. In about 1945 Blyvooruitzicht Gold Mining Company, which was then mining in to the West Driefontein area to assist in early development, decided to protect themselves from a possible inrush of water from the latter mine. A bulk head door was accordingly designed and installed on 2 level between 1945 and 1948 at 4,218 ft below surface. Since West Driefontein paid for it, Gold Fields consulting mechanical engineers collaborated with their colleagues of Rand Mines who completed their design after a few modifications were agreed. This door was never used to prevent an inrush into Blyvooruitzicht but the exercise was very useful to Gold Fields when the high pressure doors initially installed on 10 and 12 levels between Nos. 2 and 3 shafts to enable isolation of one section of the mine from another were designed. At that time the capacity of West Driefontein to cope with an inrush of water was comparatively small because the storage in stoped areas and the installed pump capacity were much less than in later years. These doors together with others of the same design were later moved to the lower levels served by sub vertical shafts. In addition, doors to prevent flood water entering the pump chambers on 18 level were installed at each end of that level, and designed for a head of 360 feet so that water would have to reach 16 level before the pumps were flooded. All these doors were called upon to hold water and it is reported that only a small plug in one of the doors and a 4 in. dia flanged pipe joint failed. The lesson is that in these cases the smallest details warrant as much attention as the major ones. That these were the only equipment failures when so much depended on equipment, is very much to the credit of design engineers, both of the Gold Fields head office and companies who supplied both mechanical and electrical equipment. Until I had read the paper I wondered why the policy of isolation by bulk head doors was not continued as the development moved eastward towards the Bank Compartment and particularly when it pierced the Bank dyke. The reasons have been given in the paper. It was unreasonable to expect provisions to be made to counter the remote contingency that the large installed pumping capacity and mine capacity to store water would be exceeded during a peak inrush. When pumps were being considered for West Driefontein, it was decided that the Gold Fields standard underground main pumps at that time of 1 million gallons per 24 hours would be too small. Three alternatives were considered. 1. Very large units that would require underground sub assembly and dismantling of both pump and motor. 2. The largest pump and motor that could be conveyed as a complete pump or motor from surface to the pump chamber. 3. Pumps of higher speed to reduce dimensions and weight. It was decided to adopt alternate 2 because of avoidance of transporting pumps in parts and assembling underground. Alternative 3 was not favoured because high speeds would have introduced problems of more exact rotor balancing. I believe the decision was correct and in the crisis enabled comparative easy transport of pumps and motors to surface for overhaul and, if required, transfer to other pump stations. The standard pump thus became a 10 stage 1,500 rpm pump with a capacity of approximately 2 million gallons per 24 hours against a static head that varied

Jan 3, 1969

By L. Forbes, G. Forbes, J. Wang

Bubble size measurement is a vital part of flotation system analysis and diagnostics. Over the years, a great many different bubble size analysis tools have been developed. However, all of them rely on ex-situ measurement and in-pulp sampling techniques. This paper evaluates the Mettler Toledo ParticleView™ Measurement probe as a novel method for in-situ bubble size measurement. This device is then compared to the conventional Anglo Platinum Bubble Sizer (StoneThree). It was found that the in-situ bubble size analysis technology appears to be a more user-friendly and reliable option for determining bubble size in flotation. However, the current instrument design is not suited to industrial applications. Keywords: Bubble size measurement, bubble coalescence, PVM probe

Jan 1, 2020

By B. T. McKenna, H. Nirschl, P. Morsch, B. Fränkle

Generally, filter media used in filter presses have a limited operational life. Besides mechanical damage, there is a growing deposition of fine particles with increasing filtration cycles, the so-called blinding, inside the filter cloth. The resulting decreasing pore diameters not only affect the efficiency of the filtration process itself by increasing the filter medium resistance, but also make it more difficult to regenerate the filter press between the individual cycles, e.g. leading to an insufficient cake discharge. Since tailings filtration requires handling of large process flows containing a significant fraction of particles in the lower micrometer range, an investigation into media rejuvenation is of interest. Keywords: Tailings filtration, filter fabric resistance, filter media regeneration, filter cleaning, intraweave contamination

Jan 1, 2020

The Technical Programme Committee-Metals Technology of The South African Institute of Mining and Metallurgy, in association with its Vaal Triangle Branch, held a one-day colloquium on 18th April, 1989, the theme being &apos;Ferous Pyrometalurgy: A Challenge for South Africa&apos;. The venue was the Auditorium 100 at the campus of the Vaal Triangle Technikon in Vanderbijlpark. Project and contract management A Project and Contract Management Conference is to be held on 19th and 20th September, 1989, at the C SIR, Pretoria. Powder metallurgy The PM 90 exhibition is to be held in Wembley, London, from 2nd to 6th July, 1990. The wide range of powders, processing machinery, and powder-metallurgy components at the exhibition will reflect the growth in this highly specialist industry. Castings and forgings Exhibition organizers, FMJ International Publications Ltd, are set to build upon the success of Castings & Forgings &apos;88, which was held as a joint event with Pat- Cast &apos;88. Castings & Forgings &apos;89-with Pat-Cast &apos;89- has already generated a high level of interest, which has been reflected in the demand for stands. Furnaces FURNACES &apos;90, the eighth in this series of exhibitions for the thermal-processing industry, will be held in Solihul, West Midlands, England, on 6th and 7th March, 1990.

Jan 1, 1989

By S. A. Hosseini, O. Asghari

"Recoverable mineral resources assessment has become a standard geostatistical application in the mining industry, with various geostatistical techniques currently available. This investigation aimed to improve the prediction at the Sungun deposit and to obtain mineral resource models capable of handling (i) the change of support from drill-hole composites to selective mining units (SMUs), (ii) the multivariate nature of the ore control selection criteria that involves both copper and molybdenum grades; and (iii) the local uncertainty on the true (unknown) grades. The solution presented in this paper is to use direct block-support sequential cosimulation in order to construct a set of alternative outcomes of the copper and molybdenum grades on block support over the deposit, with no need for storing point-support values, hence with a considerable gain in memory management and CPU time. The grade realizations so obtained are then processed to calculate the uncertainty in the mineral resources that can be recovered above given cut-off grades, both globally and on a blockby- block basis. IntroductionGeostatistical methods are widely used by mining companies to determine a resource model of the tonnage and head grade of a potential orebody, which is one of the first and most critical inputs underpinning any mining project. The prediction of the grade, tonnage, and recoverable metal for a particular mining plan and the corresponding financial forecast constitute the main technical risks in mineral resource evaluation. The conventional approach to this problem is to predict the mineral grade for constant volumes relevant to the mining plan and to base the recoverable mineral resource calculations on those predictions. Alternatively, one can directly predict the local variability in the mining block grades based on a spatial distribution model (David 1988; Rossi and Deutsch 2014). Multiple realizations can also be constructed by conditional simulation, providing a more complete representation of block grade uncertainty, as well as the uncertainty over multiple blocks. Simulation methods allow quantification of the uncertainty of the mineral resource prediction risks in downstream studies such as mine design, mine planning, or operational optimization studies; the risk assessment is achieved after applying transfer functions to the conditional simulation models (Dimitrakopoulos 2012; Rossi and Deutsch 2014)."

Jan 1, 2017

By D. N. Golenkov, N. I. Lomaka, A. V. Kozub, T. V. Ignatova, E. V. Shelepov, D. O. Sharkovskiy, A. V. Chanturiya, R. I. Ismagilov

The modern Russian iron ore mining industry is faced with multiple challenges from everincreasing requirements of steel-making, the value of iron ore concentrates, depletion of high-grade ore reserves and complications of the mining and geologic environment’s necessity to process low-grade ores with complex material composition and low valuable mineral content; with finely disseminated aggregates of metal and non-metal minerals responding similarly to processing. The upgrade of the existing operations’ fine wet screening was implemented by Metalloinvest; as well as the design of a process flowsheet for concentration oxide ferruginous quartzites with low concentrating ability. The scientific basis for improvement of low grade ore concentrating efficiency and the upgrade of market product quality is supported by an in-depth study of ore characteristics, application of high performance equipment for separation of fine-grained mineral aggregates and use of depressor selective to ferruginous minerals in the flotation process. The benefits of wet fine screening have been proven by industrial scale tests; as well as the feasibility of significant upgrades in product quality which have been confirmed as a result of the tests. A road-map for the upgrade of an existing process for the concentration of unoxidised ferruginous quartzites deposited in the Mikhailovskoye ore field was developed, based on the industrial scale test of a fine screening process. With reference to the ability for concentration, three major ore types oxidised ferruginous quartzites were defined as a result of comprehensive geological mapping and process sampling: oxidised ferruginous quartzites with good concentrating ability: over Fe67% grade of concentrate with ca. 80% iron recovery; oxidised ferruginous quartzites with moderate concentrating ability: Fe65-67% grade of concentrate with 70-72% iron recovery oxidised ferruginous quartzites with low concentrating ability: below Fe60% grade of concentrate (cannot be processed into desired grade market product). A process flow diagram combining magnetic separation and flotation has been designed and recommended for implementation based on the in-depth research of defined Mikhailovskoye deposit iron oxide types, including grain size, chemistry, petrographic, mineralogy, hematite and magnetite grain size distribution and liberation analysis.

Jan 1, 2020

By G. Asbjörnsson, E. Hulthén, P. Papadopoulou, C. M. Evertsson

Crushing plant managers need to assess, manage, and communicate the environmental impact induced by their crushing plant operations as a step towards the sustainable development of the company. However, performing reliable environmental impact calculations of crushing plants can be challenging when the availability of operational and emission data is low, and when the company’s environmental expertise is not adapted and connected to plant operations (or does not currently exist). To address these challenges, this paper proposes a practical approach where the lifecycle assessment methodology (LCA) is combined with process simulations in a web-based tool. To describe what functionality such a tool should have to be incorporated into a company’s workflow, the system that surrounds a crushing plant is analysed. Further, a case study with a three-stage crushing plant is introduced to showcase how the simulated power draw results produced with the beta version of the tool can be compared to measured sensor data from the crushing plant for one operational day. The results indicate that the simulation tool can provide an adequate estimation of the specific energy for the different material fractions and give an overview of the environmental impact of the process caused by electricity and explosives consumption. Plant managers and operators can use this tool to calculate the environmental impacts of their plant and simulate how different operational strategies influence them. Keywords: LCA, environmental impact, coarse comminution, crushing plant

Jan 1, 2020

Jigging is a process of particle stratification in which the particle rearrangement results from an alternate expansion and compaction of a bed of particles by a pulsating fluid flow. The rearrangement results in layers of particles that are arranged by increasing density from top to bottom of the bed. The particles, in addition to the vertically expanded and compacted bed motion, move continuously, horizontally across the supporting screen and helped and influenced by the feed material that is introduced at one end. Following the particle stratification, the particle bed is physically ?cut? at a desired horizontal particle density plane to separate the desired product from the less dense gangue material. The issue of correct pulse characteristics (shape, amplitude and frequency) for the optimal metallurgical stratification of air pulsating jigs has been the subject of much discussion over the years. The accuracy of the dissymmetric stratification depends on the control parameters and the mechanical condition of specific equipment used. This paper will touch on some of the control and mechanical parameters affecting the separation efficiency.

Jan 1, 2010

By G. S. Hansford, J. W. de Kock, C. D. Levy

Rheological measurements on pulps from South African gold mines by G. s. HANSFORD, Ph.D. (Pennsylvania), M.Sc. (Cape Town), C. D. LEVY, B.Sc. (Eng.), and J. W. DE KOCK, Ph.D. (Cantab.), B.Sc. (A.I.C.) (Visitors) A method is described for the determination of the rheological parameters of a fast-settling slurry with conventional viscometric measuring equipment. The effect of concentration, temperature, and pH on these parameters is investigated. The results agree with those obtained by previous workers using different viscometers, but this method allows a more detailed characterization of all the properties. From a literature survey, two semi-empirical equations were found that allow the effect of concentration, temperature, or pH on the rheological parameters to be correlated.

Jan 3, 1976