Search Documents

By I. Silin, H. Wotruba, A. Liono, I. Volobayev, Y. Rubinstein, D. Gürsel

Old, abandoned or in situ processed and storaged tailings can be a potential source of remained valuable metals and minerals. By reprocessing of tailings, it is possible not only to achieve economical profit from recovery of valuable metals, but also to reduce environmental damage caused by tailings such as generation of acid mine drainage from sulfide minerals, mobilization of heavy metals, soils and groundwater contamination. In addition, storage facilities can be successfully redesigned with modern geotechnical requirements and monitoring to avoid a dam collapse of abandoned tailings. In this case study, the processing of low grade abandoned tailings was investigated. Copper (0.15%), cobalt (0.032%) and gold (0.35 ppm) were determined as main valuable and recoverable metals. Cobalt occurs as cobaltite and cobaltiferrous pyrite, while chalcopyrite represents copper. The fine fraction of tailings below 32 μm is enriched with cobalt and copper. Preliminary test-works with initial tailings sample were aimed to recover copper, cobalt and gold. The previously tested magnetic and gravity separation could not recover the metals in a pre-concentration step. Flotation tests of the tailings sample had shown a suitability for flotation without previous regrinding of the tailings. The valuable minerals are first proposed to be recovered by collective flotation, followed by a selective circuit with production of a low grade copper concentrate and a cobalt bearing pyrite concentrate. Based on various tested collectors, amounts of sulfidisation agents and activators, a suitable reagents regime was determined and used for up-scaling by locked cycled test. Keywords: reprocessing, tailings, copper, cobalt, gold, flotation, cobaltite, cobaltiferrous pyrite

Jan 1, 2020

Contribution by W.D. Ortlepp? The authors are to be commended for publishing their interesting view of an aspect of deep-level mining technology that is becoming increasingly topical and vitally important. This is the second paper in the journal within four months to deal with the crucial needs of highly stressed tunnel construction, the other being the paper on the design and testing of rockburst support in the February 1994 issue. Both papers re-examine important innovative ideas that are more than a quarter of a century old, but that have not yet been implemented by the industry. It is to be hoped that they will now, taken together, serve as a new starting point for a definitive examination of what constitutes proper tunnel-support design. There can be no question that the need to develop a design approach that will solve the problems of tunnelling at depths of 4000 m or more has now become crucial. Contribution by A.M.J. Vervoort* Although the overall paper is very interesting and the future research (comparison between numerical simulations and underground measurements) will be very challenging, I would like to make some remarks regarding the set-up of the numerical model and the interpretation of the elastic results.

Jan 1, 1995

By P. G. Terrazas Prado

This paper presents the results of research on the development and application of a custom-made truck cycle and delay automated data collection system (TCD-ADCS) in a surface coal mining. Truck cycle and delay field data are locally stored in trucks and then synchronized and replicated through a wireless network into a centralized server containing an already-developed integrated production management system (IPMS). The system relies on motion sensing and distance travelled in order to automatically define the cycle starting/ending points, cycle time, position, and delay time. Connectivity and communication between loading equipment and trucks are also established. Communication between the equipment operators and TCD-ADCS system is via a user-friendly graphic interface. The hardware used for the development of this system consists of a rugged touch-screen personal computer, 2.4 GHz radio transmitter antenna, and a commercial GPS receiver. The system was developed, tested, and deployed at a surface coal mine in the USA. Keywords surface coal mining, truck and shovel, data collection, information systems.

Nov 1, 2013

By H. Wagner

It is a great privilege for me to have been asked to present the closing address to this most successful symposium on backfill in the South African mining industry. When I accepted this invitation I did not fully appreciate the tremendous progress made on most aspects of backfilling in the last few years. The number and quality of papers presented at this symposium bear testimony to the mining industry's determination and success in introducing backfill in underground mines to improve strata control and environmental conditions, and to provide better protection to mineworkers against the hazards of rockbursts and rockfalls. Many contributions demonstrated that these benefits can be achieved at a reasonable cost, and in some instances improved grade and higher rate of face advance result in improved economics. In my closing address I will attempt to summarize the progress made in the various aspects of backfilling underground workings and to identify those areas which, in my opinion, require further attention and effort. I will undertake this review under the following main headings: ? fundamentals of backfilling; ? design of backfill systems; ? operation of backfill systems; ? control of backfill systems; and other aspects of backfill systems.

Jan 1, 1988

By T. Grewar

"South Africa is a water-scarce country, rated as one of the 30 driest countries in the world. Worryingly, government expects water demand to outstrip supply as early as 2025. The South African government believes that substantial volumes of water can be made available through the reuse of treated mining-impacted water. Currently, however, large volumes of treated mining-impacted water are produced, often with no end use in mind other than discharge or disposal, when these treated effluents may have further uses in applications which are currently and unnecessarily using high-quality water. Treating the wastewaters to levels that meet ’fitness-for-use’ guidelines for alternative applications such as agriculture, sanitation, or industrial processes will reduce the treatment cost burden compared to potable water production. The primary conclusion of this review is that the most suitable option for re-using treated mine-impacted water is in agriculture, for irrigation of crops (food, forage, or energy crops), which currently and unnecessarily makes use of the majority of South Africa’s high-quality resources or potable water. Other findings include the realization that although guidelines and legislation for water re-use in South Africa exist and are readily available, they tend to be contradictory and confusing in many cases. It is imperative that these ambiguities and incongruities in the available guidelines and legislation for water re-use be clarified and updated swiftly IntroductionSouth Africa is a water-scarce country and is currently rated as one of the 30 driest countries in the world, with an average rainfall of 490 mm/a, approximately half of the global average. As an indicator of the degree of regional variability in South Africa’s water supply, it has been shown that 70% of all runoff is from approximately 20% of the land area. Regardless of the water scarcity faced in South Africa, our water conservation track record is poor, with an average consumption of 280 L/d per person, almost 60% more than the global average of 175 L/d per person. Around 40% of this allocation is utilized in watering lawns and gardens (Zhuwakinyu, 2017).The South African government predicts water demand to outstrip supply as early as 2025. On an international scale, the situation appears just as dire, with the United Nations High Level Panel on Water (HLPW) expecting a 40% water shortfall by 2030, which may affect up to 1.8 billion people based on current water demand trajectories (Zhuwakinyu, 2017)."

Mar 1, 2019

By P. J. How, T. O. Hagan, M. F. Handley

Inelastic deformation of highly stressed rock in deep mines needs to be quantified in both time and space. Since most deformation occurs by shear, continuous monitoring of discontinuities in the rock from boreholes holds promise. The casing. Al interpretations of shear movements are based on a simple relation between shear displacement and the resulting change in tilt of the sensor. A prototype has been constructed and has undergone laboratory trials with satisfactory results. Underground trials will commence shortly. The instrument as designed has the potential for other applications, both in the civil-engineering and mining industries. paper describes an instrument that is both cheap and reliable, and capable of monitoring such shear movements continuously. The principle of operation is based on two capacitive gravity sensors mounted orthogonaly to each other in a sealed aluminum

Jan 1, 1988

Solvent loading: It is agreed that it is advantageous, as far as reagent cost is concerned, to operate at maximum solvent loading. However, owing to the fact that no reliable automatic solvent flow controller is yet available, control tends to be erratic with the result that there is risk of losing uranium. As can be seen from Mr Tunley's plot, the graph representing total ammonia cost is fairly flat between loadings of 3.5 and 4.0 gpl, while the graph representing uranium loss in the raffinate is steep. It is, therefore, safer to operate slightly below optimum loading in the absence of absolute control. Should the purity of the final product gain importance, operation at optimum loading or even slightly above, may be advantageous. Solvent losses and clarification of pregnant solution: The cost of replacing solvent, as indicated by Mr Carman, represents a high percentage of the overall Purlex costs. It is, therefore, agreed that, amongst other factors, efficient clarification of the pregnant solution and mixer-settler design have an important bearing on the cost. However, as at Blyvooruitzicht, the Buffelsfontein plant can tolerate a suspended solids content of 50 ppm without serious deterioration in efficiency. An increase in the suspended solids content from 15 to 50 ppm normally accounts for an increase of approximately 1 ppm in amine loss. Clarification of acidic pregnant solutions is much more difficult than that of alkaline solutions. Sand clarifiers are being used at Buffelsfontein with moderate success. Clarified solutions containing less than 20 ppm of solids in suspension can be produced, depending on the quantity and type of flocculant used in the filtration process, the thickness and the grading analysis of the sand beds and the quality of supervision. An on-stream duty of approximately 0.15 gallon per sq ft of surface area is obtained. Hydraulic handling of clarifier sand, while cleaning, may effect the efficiency of a clarifier, as size segregation of sand particles may lead to inefficient "pockets" in a sand bed. Control of the solution level in the sand clarifier also affects the quality of the effluent. Exposure of the sand bed invariably causes a cloudy effluent. Recycling of the final and initial solution discharged before and after skimming the clarifier sand improves the clarification efficiency significantly. Post-precipitation of silica and possibly sulphate salts, after clarification, may give a false impression of inefficient clarification. This phenomenon is more pronounced when treating hot supersaturated solutions. Ageing and cooling of the solution before clarification assist in stabilising the solution and reduce precipitation after clarification. The maintenance cost of sand clarifiers at Buffelsfontein is in the order of 0.35 cent per metric ton of solution treated. A redundant ion-exchange column has been tested successfully, either as a primary or a secondary clarifier, depending on the quality of the filtrate treated. The conventional pebble and sand beds in the column have been retained. Operation was enhanced by the addition of a two-foot deep resin bed as a filtering medium. The suspended solids content was reduced to less than 5 ppm. Mixer-settlers: Mixer-settler design is a controversial subject but, in view of the high costs of solvent compared to relatively low pumping costs, it is believed that mixing and pumping functions should be separated. Separate facilities for pumping and mixing not only give greater operational flexibility but also permit eventual changes in the flow circuit as technology develops. Scrub technique: Unlike the pilot plant, where the crud was carried away in the aqueous phase, crud is carried over with the organic phase in the full-scale plant. This carry-over of crud into the strip bank aggravates crud formation in the first strip stage. This phenomenon may result from a slight difference in settler design and/or a variation in the relative phase depths in the two plants. Bypassing of the scrub aqueous solution from the fourth to the second stage was introduced in order to avoid dilution and partial neutralisation of the acid added to the third stage, as it is known that a low pH value enhances the transfer of iron into the aqueous phase. The low aqueous flowrate in the third scrubbing stage was overcome by introducing an aqueous phase recycle. Gleaning: Mr MacDonald's contribution on "gleaning" was most informative. This process for recovering solvent from raffinate seems to show at least as much promise as coalescers and other methods employed to date. Similar tests conducted at Buffelsfontein pilot plant gave 60 per cent amine recovery from raffinate containing 10 ppm amine. However, the circuit was not operated at equilibrium and recovery may be expected to drop as the amine concentration of the "Gleaner" circuit increases.

Determination of mineral composition is of significant importance for the mineral sands industry as this information is required for orebody evaluation, the control of mineral processing plants and the determination of product quality. Mineral processing is made more difficult by the presence of pseudorutile, leucoxene, altered-ilmenite and particle inclusions. The paper investigates the properties of such elements from a single product stream using an MLA approach.

Jan 1, 2007

An evaluation was made of the wear and performance characteristics of liter bars, and the cost-life effectiveness of backing materials for rotary-mil liners. In a large run-of-mine mil in which the liter bars were mounted on grid liners of austenitic manganese steel (AMS), the liners had an average life that was five to six times that of equivalent unprotected liners. For a single mil, this is equivalent to annual savings in the cost of materials of up to R320 000, and to a downtime of 100 hours. Of the five materials tested in a large pebble mil grinding quartzitic ore, AMS grids and 'white iron' blocks performed best on a cost-life basis, with possibly improved performance from a real white cast iron. (The 'white iron' was shown by microstructural analysis to contain flake raphite and pearlite, being in reality a grey cast iron.) The high-chromium white iron had by far the longest predicted life, with mild steel a surprising second. Rubber was shown to last well in this type of mil. The wear rates of liners change during their lifetimes. The protective effect of liter bars was clearly illustrated by the reduction of over 40 per cent in the wear rates of the liners when the lifter bars were renewed to a height of 80 mm from a fully worn height of 35 mm.

Jan 1, 1991

By D. Pienaar, C. O’Connor, B. McFadzean

Dithiophosphate (DTP) is classically used as a co-collector in sulphide mineral flotation, where xanthate-DTP mixtures have been shown to synergistically improve mineral flotation performance. Notwithstanding the improved recoveries observed, ethyl DTP does not appear to behave as a conventional collector, since it has been shown that it does not adsorb onto certain sulphide mineral surfaces. Recent investigations have nevertheless indicated that when ethyl DTP does not adsorb onto the sulphide mineral surface, the presence of a non-ionic frother can activate a synergistic increase in pulp phase mineral recovery, and bubble-particle attachment probability. A regular solution approach was used to determine the interactions between thiol collectors and non-ionic frothers at the air-water interface. Attractive interactions were observed between longer alkyl chain DTPs and frothers, whereas the activity of xanthates at the air-water interface were too weak to determine if an interaction was occurring. This is the first time that such interactions have been shown for the DTP-frother system and represents an important contribution to our understanding of the role of DTP reagents in the flotation process. Keywords: Collector-frother interaction, dithiophosphate, surfactant synergism

Jan 1, 2020

By M. Le Roux, Q. P. Campbell, M. Fofana

The determination of densimetric information to predict coal washabilities is an important step in characterising the feed material, as well as the performance of operating plants. However, traditional methods like float-and-sink analysis are hazardous and time-consuming. This is especially true for finer particle size ranges, where very long settling times are required in a medium. De Beers Technologies recently developed a density analyser, known as the RhoVol, for use on diamondiferous kimberlite. Operating over size ranges from 25 mm down to 3 mm, it can determine the mass, volume, density, size and shape of all the particles in a given population and is thus able to provide information about the densimetric distribution on a single particle basis. A study was carried out to compare uncalibrated and calibrated RhoVol results to densimetric and size data obtained using traditional zinc chloride float-sink procedures, for three different coal samples in the size range 3 mm to 8 mm. The results indicate that the RhoVol can be used to provide simple, rapid and safe size-by-washability information for coal, provided proper pre-calibration is done, mainly to account for the effects of particle porosity in the density determination. Keywords: Coal washability determination, RhoVol, densimetric curve

Jan 1, 2020

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2012

By D. Seke

Metal inventories are usually reported in financial statements of mining companies. However, the value of these inventories can be reliable only if the metals in stock are measured within acceptable tolerances. Reliable metal balancing requires accurate mass measurement, sampling, and chemical analysis. Many mining companies are usually unable to validate the accuracy of metals in inventories at the end of their financial year. This is mainly due to poor mass measurement, sampling, and chemical analysis practices. This has an adverse impact on metallurgical accounting and metal valuation. In addition, it puts a lot of stress on external auditors, who have the duty to recommend the approval of the financial statements to the board of directors. Although a full value chain of metal reconciliation includes the accuracy of Mineral Reserve definition and grade control at the mine, this paper discusses the implementation of best practices for mass measurement, sampling, and chemical analysis at processing plants. This is an important aspect of sampling and reconciliation that is required in order to improve the reporting of inventories in the financial statements of public mining companies. Keywords metallurgical accounting, corporate governance, sampling, analysis.

Jan 1, 2014

By J. C. van Dyk, F. B. Waanders, J. Brand, C. A. Strydom

"Underground coal gasification (UCG) is a fast-emerging, in situ mining technology that provides access to low-cost energy through the utilization of coal reserves that are currently not technically or economically exploitable by conventional mining methods.Groundwater monitoring for conventional coal mining in South Africa is well established, with SANS, ASTM, and ISO standards for the specific environment, location, and purposes. South Africa’s groundwater is a critical resource that provides environmental benefits and contributes to the well-being of the citizens and economic growth. Groundwater supplies the drinking water needs of large portions of the population, and in some rural areas it represents the only source of water for domestic use. Implementation of, and adherence to, groundwater monitoring standards are thus non-negotiable.The groundwater quality management mission, according to the Department of Water and Sanitation in South Africa, is set in the context of the water resources mission and reads as follows:‘To manage groundwater quality in an integrated and sustainable manner within the context of the NationalWater Resource Strategy and thereby to provide anadequate level of protection to groundwater resources and secure the supply of water of acceptable quality.’ (SABS, 2016).In this paper we propose fit-for-purpose groundwater monitoring standards for a commercial UCG operation. It is important to proactively prevent or minimize potential impacts on groundwater through long-term protection and monitoring plans. Scope of study / standard proposal The purpose of this paper is to set out a National Standard Proposal to emphasize groundwater monitoring as one of the five strategies of the ‘Policy and Strategy for Groundwater Quality Management in South Africa’ (Department of Water Affairs and Forestry, 2000) and to align it with the National Water Act, Act no. 36 of 1998 (Republic of South Africa, 1998).The focus of this standard is directed solely towards groundwater monitoring during underground coal gasification (UCG). Groundwater in this context refers to water as sampled from dedicated monitoring wells around the targeted site, which will include the shallow aquifer referred to as groundwater, and water flow at the level of the underground gasifier, referred to as ‘coal water’."

Oct 1, 2018

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publications Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. LAYOUT AND STYLE Orthodox sequence Title and author's name, with author's degrees, titles, position. Synopsis, including a brief statement of conclusions. Index, only if paper is long and involved. Introduction. Development of the main substance. Conclusions, in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors &, Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler. H. W. & F. G. The King's English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory \matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. If there is any problem in producing formulae accurately by typewriter they should be inserted by handwriting in ink in the copy forwarded by authors. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol %is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systeme International d'Unites (S.L) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramms metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, n, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and there. fore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .' . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publication of technical notes taking up to three pages (maximum 3 000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute as a body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there IS full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organizations as well as to the Institute.

By M. H. Moys

A method of estimating the percent solids in the discharge from a grinding mill is described and tested on both pilot and industrial scale. It involves the use of energy and mass balances around the mill discharge sump, requiring measurements of the flowrate and density from the sump together with temperatures of all streams flowing to and from the sump. Accurate estimates of the dynamic variation of mill discharge percent solids are made available, provided that occasional manual sampling of the stream is done to cope with drift in instrumentation. The use of a computer in this application was essential; the various advantages associated with its use are discussed. It is anticipated that this estimate of discharge density can be controlled at a set point by manipulation of the water fed to the mill, resulting in significant decreases in specific power consumption and media consumption.

Jan 1, 1987

By John Taylor

?Introduction to Black Mountain ?Historical metal accounting practice ?Metal accounting audit ?Feed measurement ?Sample precision ?Concentrate measurment ?Current metal accounting practice ?Further refinements to the metal accounting practice

Jan 1, 2005

By P. R. Mothemela

The objective of the investigation is to optimize the truck and shovel operations for pre-stripping at New Vaal Colliery by introducing campaign mining. The aim of campaign mining is to improve the efficiency of the loading, hauling, dumping, and maintenance operations which are critical to the success of truck and shovel operations. The current loading (single-sided loading method), hauling, and dumping operations at New Vaal Colliery were found to be inefficient. Time studies were used as a major indicator to highlight the inefficiency of the truck and shovel operations, and it is recommended that an improved loading configuration, hauling, and dumping operations be implemented by using campaign mining. It is also recommended that a service truck be used to maintain the pre-stripping fleet in order to reduce travelling times to the main workshop. As expected, the improved operating conditions will lead to an increase in pre-stripping production.

Jan 1, 2013

By Sh. Arshadnejad

Stress analysis in a rock medium is essential to determine the stress concentration between two consecutive circular holes and prediction of fracture behaviour. When two consecutive circular holes in a hard rock medium such as granite are loaded internally by the pressure of non-explosive expansion material (NEEM), stress concentration occurs between the holes which then causes the rock to fracture. In this work, finite element (FE) analysis using Phase2 code was employed to study the stress concentration between two consecutive circular holes under internal pressure induced by NEEM. Effects of different hole diameters and spacings, rock properties and NEEM pressures have been analysed. The data gained from the numerical analysis and analytical solutions were then used to develop two models. These models were then modified by using the FE data and polynomial regression analysis. The developed analytical models showed to be in a very good agreement with the FE analysis. Hence, the developed models can be used with confidence to determine stress distribution and concentration factors around two consecutive circular holes in a hard and brittle rock which are loaded internally by the pressure induced from the NEEM. Keywords Finite element method, non-explosive, quarry mining, stress concentration..

Jan 1, 2011

By Timo Niitti, Antti Rinne, Janne Turunen, Klaus Schommarz, Sami Grönstrand

This paper captures the essential steps employed in developing Outotec?s new FloatForceTM mechanism. The development of a flotation mechanism essentially revolves around the efficient transfer of installed power, or capital cost, to optimum flotation performance. Optimum flotation performance will be achieved if a balance between metallurgical results, operating and capital costs is maintained. The development of the FloatForceTM mechanism was done by careful evaluation of each of these three areas. This paper focuses on how experience, CFD and laboratory equipment, pilot and plant tests are used to test and evaluate a new flotation mechanism. Validated variables include mixing profile, power draw and local air hold-up. Metallurgical and mechanical design considerations are not covered in this paper. Besides using the FloatForceTM mechanism in new flotation equipment, the FloatForceTM mechanism can be used in existing flotation cell installations, thus enabling improvements in the mixing profiles, solids suspension and metallurgical performance of operating flotation circuits. Results of several tests carried out in existing plant operations are presented.

Jan 1, 2007