Search Documents

By K. Basaure, S. Palma, R. L. Castro

"Mud rushes are sudden inflows of fine wet ore within underground mines; they can harm people and equipment as well as cause production delays. Block and panel caving mines are prone to mud rushes in their production levels, with mud flowing from the drawpoints. Different mines have developed methods to control drawpoint conditions and thus perform safe ore extraction. The aim of this study is to develop a decision matrix and apply it to samples from drawpoints for the Diablo Regimiento mine, Codelco, El Teniente Division (Chile). The Abrams’s Cone was used to perform slump tests on mud samples and characterize their consistency by setting the saturation degree and packing. The unconfined strength for different saturation degrees and packing was then evaluated. The results show that conditions for fluid response in slump tests correspond to conditions for low strength in unconfined compression tests. We also found the water content value at which the flowing consistency changes from plastic to soft behaviour according to the slump test classification for each sample. This value varied between 12.2% and 16.9%, depending on the sample tested. Finally, a fluid security factor was defined in order to design an extraction pattern for the samples tested, based on the water content. We conclude that a very densely packed ore is not prone to flowing. The flow properties depend strongly on the specific properties of the ore tested, and consequently a specific criterion should be developed for different types of ore at a particular mine. The criterion developed for Diablo Regimiento ore provides critical water content values from 11% to 15%, depending on the ore type. IntroductionBlock/panel caving has the lowest cost and the highest production rates of all underground methods (Heslop, 2000; Hubert et al., 2000). Good management of the risks is important to ensure the security of personnel and infrastructure. Operational risks for the method include rockbursts, air blasts, and mud rushes (Hubert et al. 2000). A mud rush is defined as a sudden inflow of mud from a drawpoint or other underground opening into the mine (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005). Mud rushes can cause dilution, production delays, and damage to equipment as well as injuries and fatalities. The elements necessary for mud rushes are mud-forming material, disturbances, a discharge point, and water (Butcher, Joughin, and Stacey, 2000). All these elements are present in block/panel caving mines. Mud-forming material comes from ore milled by the caving process; water comes from underground and surface sources. Drawpoints in the production level are discharge points for the mud. Finally, several types of disturbance could trigger the mud rush phenomena: blasting, earthquakes, operation of equipment (Call & Nicholas, Freeport McMoRan, and Hydrologic Consultants, 1998; Jakubec, Clayton, and Guest, 2012), arch collapse above drawbells (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005; Jakubec, Clayton, and Guest, 2012) and ore drawing (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005; Call & Nicholas, Freeport McMoRan, and Hydrologic Consultants, 1998; Jakubec, Clayton, and Guest, 2012)."

Jan 1, 2017

By V. Korobko, M. Byantogtokh, N. Byambadorzh, V. Bysov

A three-stage operative planning of mining operations in ore opencasts is considered. The hierarchy of monthly-weekly, weekly-daily, daily-shift planning is offered. For the fastest elimination and deviations in problematic situations a level is analysed and weekly-daily or monthly-weekly operative plans are being constantly updated. Operative planning is formulated on information received of preparation and working of mining panels. The electronic maps of these panels are considered for automated operative planning. On the data of the registration of blasthole drillings on a panel, the position of blasthole entry, their depth and the number of a line are determined. The geologist specifies boundaries of ore grades by the bored silt. The qualitative characteristics of ores are determined by the chemical analysis of slime or magnetic logging of blastholes. The missing geologic information is obtained by interpolation on the data of detailed and operational explorations. During working of the mining panel the technologists mark the movement of shovels, associating this movement to blastholes. For this purpose technological attributes are used: when was the blasthole drilled, what drill-rig participated in drilling, what shovel was used and when was it worked? Around each blasthole the zone of its influence is built up. It represents a discrete, elementary volume of ore or waste. The discrete form of the data is most convenient, as it allows step-by-step methods to be employed of the scheduled tasks in many and various combinations. The account panel working technology avoids ‘combination’ explosions. The elementary blocks should be placed in a trajectory of shovel movement and the trajectory can not be arbitrary. It’s determined by the technological rules of extracting and loading of mine mass. In linking to blastholes, the trajectory of shovels is simulated by the sum of step-by-step moving from one elementary block to another. For this purpose a geometrical linkage of blastholes is used. At a railway haulage, or complete mining with truck haulage, the trajectory of movement is a shuttle along the front of operations in the panel. At a selective mining of ores the number of possible directions is limited to three: moving of a shovel by idle running along the front of operations in the panel, frontal pull all the way down of the panel, and withdrawal. The technologically acceptable trajectories of shovel movement are stored for the following estimation and selection of the best. The estimation is carried out on mathematical models with criteria on the method of the least squares of deviations based on preset parameters from the plan, uniform loading of shovels, and mixing of ore at unloading points. The equations of balance type and directive parameters of the plan, as well as technological restrictions of solid and of elementary blocks within the limits of a trajectory are the restrictions of the model. Depending on an industrial situation it is possible to choose one of the predetermined models. The presented technique is used for longitudinal shovel bench at the Erdenet ore-dressing company.

Jan 1, 2003

By S. M. Brabyn

The wear in mild steel pipelines used to convey rod-milled waste backfill was determined and then compared with that obtained using a laboratory rig designed to simulate the wear condition in slurry pipelines. The relative importance of corrosion and abrasion was investigated under various conditions of water quality and particle size distribution. The laboratory rig was then used to evaluate other possible materials of construction for backfill pipelines. A preliminary assessment of the economic viability of pipelines made of alternative materials is included.

Jan 1, 1988

By Luis Rudolphy, Pekka Tähkiö

"Flotation plant design, construction and start-up can be challenging tasks, because multiple factors and disciplines have to be combined in an efficient manner, in order to execute a project that meets the technical, financial and timeframe expectations. Key considerations that need to be addressed when designing a flotation plant are process requirements, equipment integrability, automation, and up- and downstream processes/designs. Furthermore, several other lifecycle factors need to be considered, such as servicing and maintainability, operational costs, future expansions and decommissioning, among others. To address these challenges, Outotec has developed a new approach to designing flotation plants that targets eliminating most of the inherent risks that can be found in these types of projects. The new Outotec® plant is a fully modular approach in which the above-mentioned challenges have been taken into consideration in the design phase. As a result, the cPlant concept can give several benefits for new and experienced companies involved in the minerals processing business, such as lower risk investments, fast and cost-efficient flotation plant delivery, faster ramp-up period, easy plant expansions, fully automated processes and operation and maintenance ease. As well, dismantling and transportation of the cPlant to a new location is easy and fast, hence the new cPlant concept makes possible to exploit small, short-lifespan ore deposits and also retreat old tailings ponds that might contain valuable minerals and where the ore quantities are limited. Furthermore, cPlant is easily implemented for brownfields and temporary expansions during bigger expansions."

Jan 1, 2015

By R. P. King

A class of gravity separation unit operations in ore-dressing relies for its operation on the production of a stratified bed. Heavier material gravitates downwards, and separation is achieved by splitting the ore horizontally, with the recovery of a dense stream and a lighter stream. The important ore-dressing unit operations that fall in this class are the jig, the Reichert cone and the pinched sluice. A new quantitative model based on Mayer's potential theory is developed here. This model is developed completely for the simple case of binary mono-size particulate materials, but the extension to units operating with feed material distributed over particle size and density is discussed in principle. The model can be used to predict the performance of these units and is very suitable for simulation. The model is tested successfully against experimental data obtained from a batch jig and a Reichert cone.

Jan 1, 1987

By E. Molobi

"Studs are rods threaded on both ends and are used as mechanical fasteners for two or more components. Stud finds usage in industries such as automotive, construction and aviation. The advantage of studs is that they allow for disassembly of components during maintenance. Studs are continuously subjected to both tensile and shear stresses, depending on the application, therefore they should be manufactured from suitable materials that are capable of withstanding all these external forces. Studs are sometimes manufactured from re-sulphurized steel due to its improved machinability; however, there is a certain limit on the amount of sulphur, above which failure may occur. Premature failure of studs has been a common problem, but failed studs are commonly replaced with new ones without conducting failure investigations. The present work investigates the premature failure of two re-sulphurized steel studs used on a rocker arm assembly and recommends alternative materials. The investigation was carried out by conducting visual examination, microstructural analysis, hardness measurements, chemical analysis and a detailed scanning electron microscopy (SEM) investigation on the fracture surface.IntroductionTwo rocker arm studs used on a 16-cylinder diesel locomotive engine failed prematurely after being in service for less than 5 months. The rocker arm studs had a life-cycle of 5 years. The studs were manufactured from resulphurized steel. The paper aims to establish whether re-sulphurized steel is applicable for the manufacture of studs in the automotive industry.BackgroundLocomotives are classified as either electric or fuel-powered. Diesel locomotives are an example of fuel-powered locomotives. This type of locomotive uses a diesel engine as a means for propulsion. An engine converts chemical energy into mechanical energy required for traction. In an internal combustion engine a rocker arm is an oscillating lever that conveys radial movement from the cam lobe into linear movement to open and close poppet valves of cylinders (Husain and Sheikh, 2013). The rocker arms are secured on to the cylinder head by rocker arm studs."

Jan 1, 2016

By Milton Syamujulu

In 1994, Nkana smelter commissioned a Multimillion US$ Dollar Chilean Teniente converter (CT) in its operations in order to improve its smelting technological base. The main objective was to reduce the overall smelting energy costs and increase the sulfur capture for sulphuric acid production to support the company?s leaching operations at Nchanga Tailings Leach Plant. A decade of CT operations have since ensured following its installation and startup. This paper provides a Technical and Operational Audit of the performance of the CT in the first 10 years of its operations at Nkana smelter.

Jan 1, 2005

By D. F. Malan, P. M. Couto

We propose a layout design for the UG2 Reef where weak geological alteration layers are present. The collapse of the Everest platinum mine in South Africa indicated that these layers substantially weaken the pillars. The popular Hedley and Grant pillar strength formula cannot be used where these alteration layers are present. Underground investigations at Everest mine and numerical modelling of the layout were conducted using the TEXAN code and a limit equilibrium model. Simulations of a collapsed area and an intact area allowed for a preliminary calibration of the model. This was subsequently used to explore modified layouts for these ground conditions. An alternative is to compartmentalize the blocks of ore using barrier pillars. The numerical modelling predicted that the barrier pillars appear to remain stable even in the case of large-scale collapses, provided their width exceeds 25 m. Main access routes into the mine can be protected by a double row of pillars at least 15 m wide to provide a safe travelling way. As a cautionary note, these conclusions are based on the model calibration and this needs to be refined in future. Calibration of the limit equilibrium model remains a challenge owing to the large number of parameters involved.

May 3, 2023

By A. Doroudgar, H. Noferesti

Unstable rock failure or rock bursting is one of the most dangerous problems in deep hard rock mines. This type of failure, that occurs uncontrollably, is associated with a significant release of strain energy from the surrounding rock. In this study, the numerical simulation of unstable rock failure was carried out using the three-dimensional explicit Lagranian finite-volume finite difference method to identify the onset and location of unstable failure events in the model. On this basis, a numerical simulation of mine pillars with width-to-height ratios of 0.5, 2 and 3 was performed. A criterion was developed, based on the calculation of the elastic strain energy, to determine the prone areas for the initiation of rockburst in the models. The results of this study showed that, in softer loading systems, due to large amounts of stored elastic strain energy, an unstable equilibrium is established, which leads to the rapid transfer of strain energy to the rock in the form of violent failure. It was also found that the unstable failure starts at the corners and free surface of the model. The new criterion developed in this study may help predict the occurrence of rockbursts in slender pillars and the design of pillars to control human and financial losses caused by this phenomenon.

Nov 27, 2024

By M. Izadi Yazdan-Abadi, S. H. Amiri, M. Ramezanizadeh, M. Bazmandeh

Iron ore concentrate is used as the fresh feed of pelletising plants. The green pellet properties depend on iron concentrate characteristics such as particle size distribution (PSD), specific surface area (Blaine value), iron grade, moisture content and grinding methods. The grinding methods affects particle size distribution and Blaine value. To find out the effects of grinding methods on pelletising process, green pellets were produced with concentrates that were reground by means of HPGR (high pressure grinding rolls) and ball mill. The Blaine values of ground concentrates in both types of milling were approximately 1400, 1600 and 1800 cm2/gr. The results of green pelletising tests on a pilot plant scale showed that at the same Blaine values, drop numbers of green pellets produced by ground concentrate inside HPGR were higher than the green pellets produced by ground concentrate inside a ball mill. Also, reground concentrates by means of HPGR, in comparison with ball mill, caused the production of green pellets, at higher wet and dry compression strengths. As a result, it was found that preparing the pelletising feed by means of HPGR led to more positive effects on the properties of green pellets. Keywords: Ball mill, HPGR, green pellet, drop number, wet and dry compression strengths

Jan 1, 2020

By Oaitse Medupe

The feed to the BCL concentrator is made of the ore from Phikwe No3 shaft, Selebi shaft and Selebi North shaft. The receiving bin of the concentrator has daily throughput of 7869mt live capacity of ore with feed grade from underground operation of 0.70%Ni, 0.75% Cu and 0.05% Co. The valuable minerals in the ore are Pentlandite, Chalcopyrite. Cobalt is present mainly in the solid solution in pentlandite. The common non-sulphides minerals are Amphibolites, quartz, micas, and Feldspar while pyrite and pyrrhotite are the major gangue sulphides. Pyrrhotite contains between 0.1% and 1% Ni in solid solution. From the mineralogical investigation, it was found that approximately 65% of the pentlandite in the ore occurs as exsolutions in the pyrrhotite and the grain sizes ranges from 8 to 38µm. about 25% of the nickel bearing pentlandite is medium grained and subhedral. This kind of pentlandite occurs along the cracks of pyrrhotite or as inclusions in pyrrhotite. The rest of pentlandite present is disseminated in the gangue matrix. Because of the fine occurrence of pentlandite, fine grinding was conducted in order to improve the recovery as well as the concentrate quality. A series of subsequent flotation test were performed in order to evaluate grinds of 35, 40, 45, 50, 60 and 80% passing 75µm. It was observed that ? The mass pull increased together with increasing fineness of grind ? Similar nickel recoveries were obtained at 35 and 40% passing 75µm but from 50% and 60% the grind was seen to adversely affect the nickel recovery. At 80% passing 75µm the recovery increased by small amount. ? Flotation kinetics showed higher initial nickel recoveries but these did not translate into higher final recoveries. ? Grinding finer than 80% passing 75µm yield very high grades of the concentrate in the first minute of the flotation test, and the grade is dramatically reduced in the fifth minute of the test. It was concluded that the current grind of approximately 48% passing 75µm is close to the optimum and no significant benefit were found to be associated with finer primary grinds. The inconsistence of the grade and recovery as well as the pentlandite losses will be discussed. Keywords: Pentlandite, Nickel losses, Grain size, Flotation

Jan 1, 2007

By I. Silin, H. Wotruba, A. Liono, I. Volobayev, Y. Rubinstein, D. Gürsel

Old, abandoned or in situ processed and storaged tailings can be a potential source of remained valuable metals and minerals. By reprocessing of tailings, it is possible not only to achieve economical profit from recovery of valuable metals, but also to reduce environmental damage caused by tailings such as generation of acid mine drainage from sulfide minerals, mobilization of heavy metals, soils and groundwater contamination. In addition, storage facilities can be successfully redesigned with modern geotechnical requirements and monitoring to avoid a dam collapse of abandoned tailings. In this case study, the processing of low grade abandoned tailings was investigated. Copper (0.15%), cobalt (0.032%) and gold (0.35 ppm) were determined as main valuable and recoverable metals. Cobalt occurs as cobaltite and cobaltiferrous pyrite, while chalcopyrite represents copper. The fine fraction of tailings below 32 μm is enriched with cobalt and copper. Preliminary test-works with initial tailings sample were aimed to recover copper, cobalt and gold. The previously tested magnetic and gravity separation could not recover the metals in a pre-concentration step. Flotation tests of the tailings sample had shown a suitability for flotation without previous regrinding of the tailings. The valuable minerals are first proposed to be recovered by collective flotation, followed by a selective circuit with production of a low grade copper concentrate and a cobalt bearing pyrite concentrate. Based on various tested collectors, amounts of sulfidisation agents and activators, a suitable reagents regime was determined and used for up-scaling by locked cycled test. Keywords: reprocessing, tailings, copper, cobalt, gold, flotation, cobaltite, cobaltiferrous pyrite

Jan 1, 2020

By R. Haldenwang, R. Erasmus, P. T. Slatter, R. P. Chhabra

Notches are used routinely for measuring the flow rate of water with free surface flows. As far as can be ascertained, no work has been done to investigate the performance of these flow rate measurement devices for non-Newtonian suspensions. The Flow Process Research Centre at the Cape Peninsula University of Technology has investigated the flow rate of kaolin and bentonite suspensions from a tank for two notch shapes, namely rectangular and triangular, and for 3 different concentrations of each suspension. The notches were calibrated using water and then the kaolin and bentonite suspensions were tested in them. The rheological characterisation of the fluids was done with a Paar Physica MC-1 rotary viscometer fitted with a cup and roughened bob. Analysis of the results shows a significant increase in discharge coefficient with increase in concentration, and the discharge coefficient has been correlated to the yield stress. This is the first such study, and further investigation is needed to confirm and extend these findings.

Jan 1, 2007

The first annual student prizegiving function of the South African Institute of Mining and Metallurgy was held in the Dorothy Susskind Auditorium, University of the Witwatersrand, on Thursday, 26th May, 1977. The address (see opposite page) was given by Dr M. G. Atmore, a director of Anglo American Corporation and Vice-President of the Institute.

Jan 1, 1977

By H. Wagner

It is a great privilege for me to have been asked to present the closing address to this most successful symposium on backfill in the South African mining industry. When I accepted this invitation I did not fully appreciate the tremendous progress made on most aspects of backfilling in the last few years. The number and quality of papers presented at this symposium bear testimony to the mining industry's determination and success in introducing backfill in underground mines to improve strata control and environmental conditions, and to provide better protection to mineworkers against the hazards of rockbursts and rockfalls. Many contributions demonstrated that these benefits can be achieved at a reasonable cost, and in some instances improved grade and higher rate of face advance result in improved economics. In my closing address I will attempt to summarize the progress made in the various aspects of backfilling underground workings and to identify those areas which, in my opinion, require further attention and effort. I will undertake this review under the following main headings: ? fundamentals of backfilling; ? design of backfill systems; ? operation of backfill systems; ? control of backfill systems; and other aspects of backfill systems.

Jan 1, 1988

By P. G. Terrazas Prado

This paper presents the results of research on the development and application of a custom-made truck cycle and delay automated data collection system (TCD-ADCS) in a surface coal mining. Truck cycle and delay field data are locally stored in trucks and then synchronized and replicated through a wireless network into a centralized server containing an already-developed integrated production management system (IPMS). The system relies on motion sensing and distance travelled in order to automatically define the cycle starting/ending points, cycle time, position, and delay time. Connectivity and communication between loading equipment and trucks are also established. Communication between the equipment operators and TCD-ADCS system is via a user-friendly graphic interface. The hardware used for the development of this system consists of a rugged touch-screen personal computer, 2.4 GHz radio transmitter antenna, and a commercial GPS receiver. The system was developed, tested, and deployed at a surface coal mine in the USA. Keywords surface coal mining, truck and shovel, data collection, information systems.

Nov 1, 2013

Solvent loading: It is agreed that it is advantageous, as far as reagent cost is concerned, to operate at maximum solvent loading. However, owing to the fact that no reliable automatic solvent flow controller is yet available, control tends to be erratic with the result that there is risk of losing uranium. As can be seen from Mr Tunley's plot, the graph representing total ammonia cost is fairly flat between loadings of 3.5 and 4.0 gpl, while the graph representing uranium loss in the raffinate is steep. It is, therefore, safer to operate slightly below optimum loading in the absence of absolute control. Should the purity of the final product gain importance, operation at optimum loading or even slightly above, may be advantageous. Solvent losses and clarification of pregnant solution: The cost of replacing solvent, as indicated by Mr Carman, represents a high percentage of the overall Purlex costs. It is, therefore, agreed that, amongst other factors, efficient clarification of the pregnant solution and mixer-settler design have an important bearing on the cost. However, as at Blyvooruitzicht, the Buffelsfontein plant can tolerate a suspended solids content of 50 ppm without serious deterioration in efficiency. An increase in the suspended solids content from 15 to 50 ppm normally accounts for an increase of approximately 1 ppm in amine loss. Clarification of acidic pregnant solutions is much more difficult than that of alkaline solutions. Sand clarifiers are being used at Buffelsfontein with moderate success. Clarified solutions containing less than 20 ppm of solids in suspension can be produced, depending on the quantity and type of flocculant used in the filtration process, the thickness and the grading analysis of the sand beds and the quality of supervision. An on-stream duty of approximately 0.15 gallon per sq ft of surface area is obtained. Hydraulic handling of clarifier sand, while cleaning, may effect the efficiency of a clarifier, as size segregation of sand particles may lead to inefficient "pockets" in a sand bed. Control of the solution level in the sand clarifier also affects the quality of the effluent. Exposure of the sand bed invariably causes a cloudy effluent. Recycling of the final and initial solution discharged before and after skimming the clarifier sand improves the clarification efficiency significantly. Post-precipitation of silica and possibly sulphate salts, after clarification, may give a false impression of inefficient clarification. This phenomenon is more pronounced when treating hot supersaturated solutions. Ageing and cooling of the solution before clarification assist in stabilising the solution and reduce precipitation after clarification. The maintenance cost of sand clarifiers at Buffelsfontein is in the order of 0.35 cent per metric ton of solution treated. A redundant ion-exchange column has been tested successfully, either as a primary or a secondary clarifier, depending on the quality of the filtrate treated. The conventional pebble and sand beds in the column have been retained. Operation was enhanced by the addition of a two-foot deep resin bed as a filtering medium. The suspended solids content was reduced to less than 5 ppm. Mixer-settlers: Mixer-settler design is a controversial subject but, in view of the high costs of solvent compared to relatively low pumping costs, it is believed that mixing and pumping functions should be separated. Separate facilities for pumping and mixing not only give greater operational flexibility but also permit eventual changes in the flow circuit as technology develops. Scrub technique: Unlike the pilot plant, where the crud was carried away in the aqueous phase, crud is carried over with the organic phase in the full-scale plant. This carry-over of crud into the strip bank aggravates crud formation in the first strip stage. This phenomenon may result from a slight difference in settler design and/or a variation in the relative phase depths in the two plants. Bypassing of the scrub aqueous solution from the fourth to the second stage was introduced in order to avoid dilution and partial neutralisation of the acid added to the third stage, as it is known that a low pH value enhances the transfer of iron into the aqueous phase. The low aqueous flowrate in the third scrubbing stage was overcome by introducing an aqueous phase recycle. Gleaning: Mr MacDonald's contribution on "gleaning" was most informative. This process for recovering solvent from raffinate seems to show at least as much promise as coalescers and other methods employed to date. Similar tests conducted at Buffelsfontein pilot plant gave 60 per cent amine recovery from raffinate containing 10 ppm amine. However, the circuit was not operated at equilibrium and recovery may be expected to drop as the amine concentration of the "Gleaner" circuit increases.

Determination of mineral composition is of significant importance for the mineral sands industry as this information is required for orebody evaluation, the control of mineral processing plants and the determination of product quality. Mineral processing is made more difficult by the presence of pseudorutile, leucoxene, altered-ilmenite and particle inclusions. The paper investigates the properties of such elements from a single product stream using an MLA approach.

Jan 1, 2007

By D. Pienaar, C. O’Connor, B. McFadzean

Dithiophosphate (DTP) is classically used as a co-collector in sulphide mineral flotation, where xanthate-DTP mixtures have been shown to synergistically improve mineral flotation performance. Notwithstanding the improved recoveries observed, ethyl DTP does not appear to behave as a conventional collector, since it has been shown that it does not adsorb onto certain sulphide mineral surfaces. Recent investigations have nevertheless indicated that when ethyl DTP does not adsorb onto the sulphide mineral surface, the presence of a non-ionic frother can activate a synergistic increase in pulp phase mineral recovery, and bubble-particle attachment probability. A regular solution approach was used to determine the interactions between thiol collectors and non-ionic frothers at the air-water interface. Attractive interactions were observed between longer alkyl chain DTPs and frothers, whereas the activity of xanthates at the air-water interface were too weak to determine if an interaction was occurring. This is the first time that such interactions have been shown for the DTP-frother system and represents an important contribution to our understanding of the role of DTP reagents in the flotation process. Keywords: Collector-frother interaction, dithiophosphate, surfactant synergism

Jan 1, 2020

By T. Grewar

"South Africa is a water-scarce country, rated as one of the 30 driest countries in the world. Worryingly, government expects water demand to outstrip supply as early as 2025. The South African government believes that substantial volumes of water can be made available through the reuse of treated mining-impacted water. Currently, however, large volumes of treated mining-impacted water are produced, often with no end use in mind other than discharge or disposal, when these treated effluents may have further uses in applications which are currently and unnecessarily using high-quality water. Treating the wastewaters to levels that meet ’fitness-for-use’ guidelines for alternative applications such as agriculture, sanitation, or industrial processes will reduce the treatment cost burden compared to potable water production. The primary conclusion of this review is that the most suitable option for re-using treated mine-impacted water is in agriculture, for irrigation of crops (food, forage, or energy crops), which currently and unnecessarily makes use of the majority of South Africa’s high-quality resources or potable water. Other findings include the realization that although guidelines and legislation for water re-use in South Africa exist and are readily available, they tend to be contradictory and confusing in many cases. It is imperative that these ambiguities and incongruities in the available guidelines and legislation for water re-use be clarified and updated swiftly IntroductionSouth Africa is a water-scarce country and is currently rated as one of the 30 driest countries in the world, with an average rainfall of 490 mm/a, approximately half of the global average. As an indicator of the degree of regional variability in South Africa’s water supply, it has been shown that 70% of all runoff is from approximately 20% of the land area. Regardless of the water scarcity faced in South Africa, our water conservation track record is poor, with an average consumption of 280 L/d per person, almost 60% more than the global average of 175 L/d per person. Around 40% of this allocation is utilized in watering lawns and gardens (Zhuwakinyu, 2017).The South African government predicts water demand to outstrip supply as early as 2025. On an international scale, the situation appears just as dire, with the United Nations High Level Panel on Water (HLPW) expecting a 40% water shortfall by 2030, which may affect up to 1.8 billion people based on current water demand trajectories (Zhuwakinyu, 2017)."

Mar 1, 2019