Search Documents

By L. Capponi

At Tapira Mine (Tapira/MG/ Brazil), the largest phosphate concentrate producer in Brazil, the mining is fully mechanized and carried out using open pit mining. This work presents a review of the sampling protocol used for short term mine planning at different stages. Sampling is carried out in two steps. Firstly, diamond drill cores are sampled at 50 x50 x5 metre pattern. Fosfertil analyses grades of P2O5, Fe2O3, CaO, MgO, SiO2 and TiO2 plus geological logging. This information feeds the long term block model. Secondly, drill cuttings are collected at the mining faces released for blasting. The drilling pattern is staggered and when blasting is not necessary, a drill hole is made centered in the block area (25 x 25 x 5 m). The primary samples have mass approximately 60 kg and the same chemical parameters are analysed. Metallurgical and mass recovery tests are performed as well. These samples are used to build the short term block model. At the final stage, the short term mine planning model is used to build a stockpile blending model which is simulated using a spreadsheet to match the goals established by the process plant.

Jan 1, 2009

The depletion of favourably located and higher-grade mineral deposits, combined with more favourable metal prices and higher capital costs, has stimulated research into heap leaching of lower grade ores and wastes. This has resulted in renewed interest in heap leaching of uranium ores, and in the development of processes for the bacterial heap leaching of low-grade chalcopyrite ores and the acid heap leaching of nickel laterites. A complete programme of heap leach testwork typically involves a sequence of bottle roll tests and column tests, followed by piloting on test heaps. The initial testwork is aimed at determining the amenability of the ore to heap leaching, which depends on the characteristic of the ore with respect to porosity and permeability to leach liquor, acid consumption, metal recovery and percolation. Subsequent phases of the testwork focus on the development of the process design criteria for the treatment of the ore. Basic techno-economic models have also been developed as a tool for the initial estimation of heap leach viability. Mintek has also developed in-heap monitoring probes, coupled to an operator guidance system, in order to assist the operator in achieving optimal conditions for bacterial growth and heat preservation during pilot-plant operation.

Jan 1, 2009

The 114th Annual General Meeting of The Southern African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Thursday, 11 August 2011. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, and also to recipients of awards, senior members of industry, Honorary Life Fellows, past-presidents, our members and other guests, among them the following: F. Cawood, President, Institute of Mine Surveyors of South Africa C. Roode, President, Mine Metallurgical Managers' Association of South Africa M. Cresswell, Chairman, South African Coal Processing Society A. Hay, Immediate Past President, South African Institute of Electrical Engineers L. Gardner, President, South African National Institute of Rock Engineers J. Krynauw, President, The Geological Society of South Africa (GSSA)

Jan 1, 2011

By J. B. A. Solar Menéndez, M. A. Martínez Fidalgo, L. A. Alvarez-Santullano

1. ANTECEDENTS This present communication refers to the results of the research project entitled "Training in the correct use of chemical oxygen self rescue apparatus and also an analysis of apparatus autonomy", carried out under the auspices of the Specific Collaboration Agreement signed between the Industry Council of the Principality of Asturias (Spain) and INSALUD (National Silicosis Institute, Spain). The antecedents of this project lie in work undertaken by the National Silicosis Institute aimed at optimising efficiency in the use of chemical oxygen self rescuers through improvements in worker training. To be precise, by means of Agreements drawn up between the above-mentioned parties, a simulator was designed and incorporated as the basis of a training station within the " Fundación Barredo" of the Industry Council of the Principality of Asturias. This has been operative since the year 2001 and, up to the present, 2300 Asturian coal mine workers have been trained there. What prompted this activity was the observation of various errors in the use of the self rescuers, deriving from their innate characteristics, especially with respect to the sensation of discomfort - the high temperature and humidity of the breathed oxygen, resistance and inconvenience - and limited autonomy. It was precisely this insight that, in critical situations, lack of familiarity with the conditions of discomfort likely to be experienced during the evacuation process might lead to rejection of the equipment, with fatal consequences, that has justified the setting up of this training and simulation centre. The centre is able to provide all mine workers with the necessary training, and experience of the characteristic sensations experienced when using such equipment (Fig.. 1).

Jan 1, 2003

By C. M. Rule, A. K. Anyimadu, L. Knopjes

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004, and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November2006 at the Potgietersrus Platinum (PPL) ?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Key Words: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, Platinum, Palladium, PGMs, tailings.

Jan 1, 2006

The Skorpion process comprises three processing steps-atmospheric leaching in sulfuric acid, zinc solvent extraction and electrowinning to produce special high grade zinc. The major mode of impurity transfer was attributed to crud runs in the solvent extraction circuit. Crud may be described as a heterogeneous, partly inorganic, partly organic mass of material which accumulates predominantly at the interface between organic and aqueous solutions. The paper describes the root causes of the crud formation in the solvent extraction circuit and optimization strategies which are being followed to prevent impurity excursions in electrowinning. Keywords: zinc oxide, solvent extraction, crud formation, colloidal silica.

Jan 1, 2007

By C. J. Badenhorst

The primary focus of management today is safety, or preventing negative, generally irreversible, events of acute duration. The outcomes of safety-related events are usually visible and can evoke strong emotions if the results are severe. Experts now see that occupational illness and disease also result in significant emotional and financial toll to workers, their families and communities, and to their employers. Effective health and safety management must include acknowledging the importance of occupational health hazards and the proportionate application of resources to address those issues. Improvement in workplace conditions and decrease or elimination of illness and disability are due to actions within the workplace and result from the implementation of risk prevention and control measures. However, success may only be visible months or years later and may require interventions that have to be maintained over prolonged periods. This demands continuous, co-ordinated effort to ensure sustainability of diverse occupational health programmes and the relevant management systems. Too often occupational health is not seen as being part of the general management of business, but rather the function of a medical practitioner somewhere off site in a clinic. Integration of occupational health management systems with other management systems within an organization is essential for its success.

Jan 1, 2004

Dr Andrew Cosgarea, Jr, Associate Director of Opera¬tions of the U.S. Mint, and Chairman of the Awards Committee of the International Precious Metals Institute, announced the IPMI award recipients for 1985. The awards were presented at the Institute's Annual Banquet in New York City on 11th June, 1985. The Distinguished Achievement Award was presented posthumously to Dr E.M. Savitsky, of the A.A. Baikow Institute of Metallurgy of the U.S.S.R., for a life-time career devoted to investigations on the properties of the platinum-group metals. Dr Savitsky investigated over 300 phase diagrams, which became the basis for the selection of alloys and the prediction of properties. He published over 300 technical papers during his career. Dr Savitsky died during the summer of 1984 while being considered for the IPMI Award. The Engelhard Henry J. Albert Award was presented to Dr Stephen J. Lippard, Professor of Chemistry, MIT, in recognition of his research contributions in platinum chemistry and its application to nucleic acids. This prize

Jan 1, 1985

By J. L. Taylor, E. B. Viljoen, W. M. Craig, A. M. McIntosh

The Chemwes uranium plant treats old gold-plant residues from the Sttifontein and Buffelsfontein Gold Mines by acid leaching, belt filtration, countercurrent ion exchange (ClX), and Bufflex solvent extraction (SX). The uranium is recovered by precipitation as ammonium diuranate. Absorption and elution in the CIX section are achieved in four NIMCIX columns operating as two parallel streams. Each loading column is 4,85 m in diameter and contains 12 absorption stages. The elution columns are 3 m in diameter and contain 8 stages. The eluant used is 10 per cent sulphuric acid at ambient temperature. During the commissioning and initial operating periods reported here, the plant yielded an average barren solution of 1,6 p.p.m. of U3O8 from a feed with a mean U3O8 concentration of 132 p.p.m. The U3O8 concentrations in the barren solution were better than 2 p.p.m. some 85 per cent of the time, and better than I p.p.m.73 per cent of the time. Investigations are underway to institute an automatic control system that will result in the U3O8 values on the resin and in the barren solution being maintained at or near the target values in spite of changes in the concentration of uranium in the feed solution.

Jan 1, 1982

By L. Bam, R. Machaka, S. Chikosha, N. S. Muchavi

"Parts manufactured through power metallurgy (PM) typically contain pores that can be detrimental to the final mechanical properties. This paper explores the merits of 3D X-ray computed tomography over traditional microscopy for the characterization of the evolution of porosity in metal injection moulding (MIM) and direct powder rolling (DPR) products. 17-4 PH stainless steel (as-moulded, as-debound and sintered) dog-bone samples produced via MIM and Ti-HDH strips (as-rolled and sintered) produced via DPR and were analysed for porosity. 3D microfocus X-ray tomography (XCT) analysis on specimens from both processes revealed spatial variations in densities and the existence of characteristic moulding and roll compaction defects in agreement with traditional microscopic microstructural analysis. It was concluded that micro-focus XCT scanning can be used to study MIM and DPR parts for the characterization of the amount, position and distribution of porosity and other defects. However, the majority of the sub-micron sized pores could not be clearly resolved even at the highest possible instrument resolution. Higher-resolution scans such as nano-focus XCT could be utilized in order to fully study the porosity in MIM and DPR parts. IntroductionMetal injection moulding (MIM) is a novel process, which combines the advantages of powder metallurgy (PM) and plastic injection moulding. MIM has found widespread applications in the cost-effective production of high-sintered density small parts with complicated shapes and mechanical properties equivalent to those of wrought materials (German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013). There are four basic processing steps involved in MIM, namely; feedstock preparation, injection moulding, debinding and sintering. These steps are discussed in greater detail elsewhere (Machaka, Seerane and Chikwanda, 2014; German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013).Feedstock preparation involves mixing metal powder with a carefully selected composition of polymeric binder materials at a specific temperature. The feedstock is then granulated and injected into a predefined mould die with the desired shape. The part produced during the moulding step is referred to as a ‘green’ component. The green component typically contains no porosity since the spaces between adjacent powder particles are readily filled with the binder materials (German and Bose, 1977; Li, Li and Khalil, 2007). Debinding is the systemic removal of the binder components by chemical, catalytic, or/and thermal means while maintaining the shape of the component. The part produced after the debinding step is referred to as a ‘brown’ component. Debinding is known to be the source of porosity in brown components (Ji et al., 2001; Tsai and Cen, 1995). Finally, the brown debound part is sintered to full or nearfull density (Sotomayor, Varez and Levenfeld, 2010). The sintering step and associated densification closes up the majority of the pores. Sintered MIM parts are typically sintered to high density (95–99%) and retain an irreducible amount of residual porosity (Barriere, Liu and Gelin, 2003; German, 1990)."

Jan 1, 2016

By A. Nhasengo

Paper written on project work carried out in partial fulfilment of B. sc. Eng (Mining Engineering) The purpose of this investigation was to assess the mining strategy for steep reefs at Mine A mine in 2005 and 2006. Reefs steeper than 35° were discovered when production commenced at the mine. At that time reefs steeper than 35° were not popular in South African tabular gold mines, therefore new techniques of mining them had to be developed. The underhand mining method was chosen for this purpose. The project was about assessing ventilation, support costs, local support cycles, adherence to the mine?s support standards, mine planning and efficiencies of the underhand mining method. The project work was covered by doing a literature research for underhand mining methods and performing a literature review of the mining methods, support methods, ventilation standards at Mine A. Underground visits were conducted at Mine A mine for data collection, and Mine B was visited to obtain information on support costs and efficiencies. During the investigation it was realized that the underhand mining method was an appropriate method for mining steep reefs; however, there were some challenges related to ventilation and support installation. Efficiencies could be realized with the underhand mining method and planning and scheduling were not different from breast mining.

Jan 1, 2007

By C. M. Suhr

n order to validate the borehole analysis valuation procedure commonly used in the South African gold mining industry, a simulated orebody was used to create borehole values which would serve as data for the procedure. After confirming the distribution, calculating the variance size of area relationship, estimating the block variance, and calculating a profit measurement for each set, comparisons were made to the known population parameters. Results show only one overall bias (in the estimation of the lognormal third parameter), which is carried throughout the analysis. The remainder of the analysis is unbiased, validating the procedure.

Jan 1, 1987

1. Book review • World mineral statistics 1974 to 1978. Production: Exports: Imports. London, H.M.S.O., Institute of Geological Sciences, 1980. (Reviewer: R. P. King) This edition is the third in a regular series prepared by the Institute of Geological Sciences. It is a useful compilation of statistics on the production, export, and import of fifty-eight different mineral commodities. Each mineral is listed by country, and a table is provided for the annual production, the annual imports, and the annual exports for each commodity included. However, some commodities are treated in considerably more detail; for example, aluminium and bauxite have tables under the following headings: Production of Bauxite, Production of Alumina, Production of Primary Aluminium, Exports of Bauxite, Alumina and Aluminium, Imports of Bauxite, Alumina and Aluminium. The information presented is the latest official information available from primary sources; the compilers have not relied on data from secondary compilations. This publication will be of considerable assistance to all who are concerned with the trading of mineral commodities and their production.

Jan 1, 1981

By P. J. Petit

Changing mining conditions, legislative issues, rising costs, and the constrained supply of skills and electricity in South Africa, have been some of the criteria forcing mine operators and engineers to review the traditional use of compressed air to power underground hand-held drilling operations in narrow-stope, hard-rock mines. In answering the question, 'What is the best way to power this mine?', they have resorted to trade-off studies with results of limited usefulness, because they are site-specific, and use only a few comparative parameters, based on a small data set. This paper aims to provide definitive, objective and quantitative decision-making approaches to evaluate alternative energy delivery systems for stoping in narrow-reef hard rock mines, based on primary and relevant criteria. These include quantifiable criteria such as capital expenditure, operating costs, resulting financial returns, energy and water usage, production performance, life-of-mine, etc. Other important criteria with qualitative aspects are integrated. These are safety, health and environmental concerns, legislative requirements, business risk, technology change, etc. The paper begins with a review of decision making processes available, and proposes the use of the analytical hierarchy process (AHP) method as a multiple-criteria decision making tool and the decision tree-based on milestone-driven uncertainties, to validate the selection of the energy delivery system. The results of a multiple-criteria questionnaire completed by a variety of industry experts and professionals, such as production and operation managers, consultants, suppliers and techno-financial analysts, are discussed. The evaluation indicates the potential for hydropower to be the best solution for narrow reef hard rock mines, based on current information, mine design layout and production.

Jan 1, 2012

By J. Loubser

The concept of caring is in most cases confused with material needs and not psychological needs. By giving employees a job, most managers think that employees should be grateful and return the favour by being loyal, productive and working safely. Other managers hold the view that employees can be lucky to have a job. To show and demonstrate that management are caring for the safety of the workforce requires involvement, dedication and commitment. Obtaining the trust and respect of the workforce should be the main thrust of any organization because within trust and respect lie the secret of optimal safety performance. In the last 70 years, all the fatalities and serious injuries that occurred in the mining industry can be traced back to one thing, non-caring. The same safety non-compliances are still observed, reported and planned against as 70 years ago, and strange as it may sound, the same injuries occur the same way. The question could be asked: Does the mining industry need more risk assessments? More codes of conduct? More engineering. Or does the mining industry need more caring?

Jan 1, 2010

By André Fouché

GFWW Bulk Sample Prep Plant INDEX ?Features ?Flow Diagram ?Pictures of Plant

Jan 1, 2005

By D. -X. Li

The paper covers many literature reports of processes using nitrogenous species as an oxidant for processing refractory gold ores, especially development in the pretreatment of refractory gold minerals by nitric acid. These processes include the high-pressure and the atmospheric-pressure oxidation methods. High-pressure oxidation processes are difficult to carry out, because they require high-capital cost autoclaves. Atmospheric-pressure oxidation processes are easier to manipulate, but complete absorption and reuse of NOx is difficult or multiple-stage absorption must be established for its reuse. So, some new methods were developed, such as catalytically oxidizing technology of NOx to allow subsequent recovery of gold. Keywords: nitric acid; pretreatment; refractory gold

Jan 1, 2009

Dr J. P. Hugo, Pr. Eng., after obtaining a B.Sc. (Eng.) in Metallurgical Engineering at the University of the Witwatersrand in 1948, gained about 9 months' practical experience in a British steelworks, followed by post-graduate studies at Sheffield University, leading to a Ph.D. (Metallurgy) in 1953. Mr G. Y. Nisbet, Pr. Eng., holds a B.sc. (Min.) from the University of the Witwatersrand (1948) and a P.M.D. from Harvard University, U.S.A. (1966). On graduating, he was awarded the Chamber of Mines' Gold Medal. Professor D. G. Krige, holds a D.Sc. (Eng.) from the University of the Witwatersrand (1963) and a D.Ing. (H.C.) from the University of Pretoria (1981). Dr P. T. Wedepohl holds a B.Sc. (Hons.) from the University of the Witwatersrand (1953) and a Ph.D. from the University of Reading, England (1958).

Jan 1, 1984

By G. M. J. van Heerden, R. C. W. Webber-Youngman

"This article describes the re-engineering principles applied in the design of a personnel transportation system for the Bafokeng Rasimone Platinum Mine in the Rustenburg area of South Africa. It incorporates conveyor belt travelling, chairlift operation, and also includes consideration of proposed changes/modifications to the existing conveyor belt infrastructure.The purpose of the project was to identify, through a process of evaluation, the appropriate option and/or combination of transportation options that would be safe in terms of personnel transportation as well as cost-effective. Alternative measures for transporting personnel (not using belt riding) would have a significant positive spin-off, increasing the availability of the belt and thereby increasing production. This paper explores the feasibility of interventions that would improve safety through eliminating risk associated with personnel transportation as well as contributing towards improving the mine’s position on the cost curve.The design in consideration at the Bafokeng Rasimone Platinum Mine consists of two shaft systems, namely the North Shaft and South Shaft, each comprising twin decline shafts. One of the decline shafts is equipped with a conveyor belt for rock and personnel transportation, and the other with a winder for trackbound material transport. The conveyor belt has been used for personnel transportation since the commissioning of the shafts. The conveyor belt is equipped with platforms for personnel getting off and on the belt and a number of safety devices designed to ensure safety while travelling on the belt. Intensive training in the practical aspects of belt riding is given to every person, and unsupervised riding on the belt is permitted only once belt riding competence is demonstrated. Despite this, the safety results were poor, with 106 injuries between 2006 and May 2013. Fortunately, no fatalities were reported during this period.An investigation of alternative means for personnel transportation or engineered solutions to the current conveyor belt infrastructure in the safest, most effective, and most economical way was therefore needed. There was a major risk of safety-related stoppages being imposed following another belt accident/incident. This would prevent the mine from transporting personnel underground by belt and result in major production losses. From the commissioning of the Phase 2 shaft deepening project on both shafts, dedicated chairlifts have been used for personnel transportation as opposed to the conveyor belt installed in the Phase 1 area. The chairlifts have been in operation since 2004 and no chairlift-related incidents have been recorded thus far. According to safety statistics, it is clear that the chairlift is the safer method for the transportation of people in the shaft.To fulfil the objectives/scope of this study, it was recommended that both primary (new chairlift decline with infrastructure) and secondary options (modifications to the current conveyor belt infrastructure) be considered for implementation on both the North Shaft and South Shaft to reduce or eliminate accidents/incidents as a result of belt transportation. The associated capital expenditure would be approximately R200 million. Considering the future impact on the business as a whole, this would definitely be capital well spent."

Jan 1, 2016

By N. Duda, P. Śliwiński, P. Stefaniak, B. Jachnik

Ventilation and air-conditioning are some of the most energy-consuming processes in deep underground mining. Additionally, the energy consumption of these processes systematically increases along with the expansion of the mine. Therefore, proper energy efficiency assessment and consumption forecasts of these systems are particularly important in modern mines for ongoing tracking and planning of the likely costs. In the article, a short-term prediction model for surface air–conditioning stations is described. This model takes into account dependencies that were identified, based on the data from the supervisory control and data acquisition (SCADA) systems. These dependencies between the response value and the external conditions are then incorporated into the model. This way, for example, the ambient temperature or the total number of specific days of the week (with sometimes significantly lower or higher than the weekly average energy consumption levels) are included. Taking into account these dependencies, and e.g. forecasted average monthly temperatures allow us to include the seasonality of energy consumption in the presented model. In the article, a sample energy efficiency analysis of the A/C system based on an example of the KGHM Polish Copper Polkowice-Sieroszowice mine is performed. The results of the solution proposed in the article are then evaluated, and compared to the currently functioning, more basic forecasting methods. However, given the general nature of the dependencies used in the model, similar solutions could be used in other case studies.

Sep 1, 2021