Search Documents

Objective To reduce equipment operator exposure to respirable dust in enclosed cabs by examining the effectiveness of retrofitting air pressurization and filtration systems on existing cabs. Background Many types of heavy equipment are used in mining, construction, and agriculture. Most have enclosed cabs to protect the equipment operator from excessive dust and noise exposure. When the equipment is new, controls are normally implemented into the cab to keep these exposures at acceptable levels. However, as this equipment becomes older, many components of the enclosure deteriorate, such as gaskets and seals. This causes the effectiveness of the enclosed cab to be greatly reduced. Once this occurs, the equipment operator's dust exposure can increase to hazardous levels. In surface mining operations, elevated exposures to crystalline silica have caused an excessive incidence of silicosis. Approach A cooperative research study with a mining operation and a cab filtration company was conducted to evaluate the effectiveness of retrofitting an older surface drill with two controls to lower the drill operator's respirable dust exposure. These two controls were: (1) A good air filtering and pressurization system to ensure that clean air was delivered into the enclosed cab. Ideally, the incoming air filter should be 99% efficient in removing particles with an aero- dynamic diameter of 0.3 pm or greater from the airflow. (2) Sufficiently sealing the cab to develop a positive static pres- sure and ensure that dust was not leaking into the cab. This was done by plugging all holes and cracks and maintaining good gaskets and seals. To prevent wind from forcing contaminated air through holes in the cab, the cab's static pressure must be greater than the wind's velocity pressure. During the course of this research, it was found that a floor heater fan used in the drill during the winter months greatly increased the operator’s Respirable dust exposure. Problem Identification Four days of background dust levels were measured as a baseline for this research. These baseline measurements were taken in May 2000 when air temperatures ranged from 60° to 70° F. When this was completed, the two controls were implemented. The first control was to install an improved air filtering and pressurization system on the enclosed cab. This was composed of a two-stage prefilter, a blower, then the respirator-medium secondary filter. Since the secondary filter was on the positive side of the fan, all air delivered into the enclosed cab had to pass through this secondary filter. After the filtering system was installed, the cab was pressurized to a static pressure of0.01 inches of water (w.g.), which is still very minimal. The second control was to seal the cab. New door gaskets were installed, and all cracks and holes in the shell of the enclosure were plugged. This increased the cab pressurization to approximately 0.1 inches w.g.

Mar 1, 2001

By J. O. Winget

Amino acids were investigated in conjunction with rare-earth separation by ion exchange to determine whether they can be utilized effectively as retaining agents for metals separation using ethylenediaminetetraacetic acid (EDTA) eluant at 85° to 90° C. Hydroxyethylethylenediaminetriacetic acid (REDTA) and diethylenetriamine pentaacetic acid (DTPA) were the most effective amino acids investigated. Elements of atomic numbers 39 and 57 through 68 were effectively retained, whereas elements of atomic numbers 69 through 71 passed through the retaining-agent band. Utilization of REDTA or DTPA retaining agents allows an increase of 75 percent in the EDTA eluant concentration over that possible with hydrogen-or copper-retaining ions without precipitation occurring. Eighty-five percent recovery of the EDTA eluant collected before rare-earth breakthrough and during elution of lutetium, ytterbium, and thulium, and essentially complete recovery of the REDTA or DTPA retaining agents, are possible without extensive processing.

Jan 1, 1968

By M. Carrales, C. J. Jirik, W. D. Dietzman

In view of the developments and recent interest in recovering heavy oil , this report was prepared to present general information on more than 2,000 heavy oil reservoirs in more than 1,500 fields in 26 states . Information given on each heavy - oil deposit includes the following items : Field and formation , location , average or range of depth , average API gravity of oil , average thickness of formation , areal extent of field , total productive wells drilled in field , discovery date of field , field status in 1963 , cumulative production to Jan. 1 , 1964 , and all known types of secondary - recovery operations initiated ( active and terminated ) in the reservoirs . The geographical location of heavy oil accumulations in the United States is shown by a map , and a brief discussion of 14 different areas is given in the text . As of Jan. 1 , 1964 , 75 percent of the heavy oil reservoirs in the United States had produced more than 10 billion barrels of oil and are estimated to contain over 90 billion barrels of oil in place . It is also estimated that if the deposits which have had little or no production history , such as the one in Missouri , were included , the total remaining heavy oil in place would be in excess of 150 billion barrels . To find economical ways of recovering this vast reserve of heavy oil , industry is developing technology in several types of thermal - recovery methods . Some of the general considerations and more suitable limitations in selecting a prospect to study for thermal - recovery techniques are : Lithology , depth , viscosity of reservoir fluids , gravity of oil , reservoir thickness , oil in place , and permeability and porosity .

Jan 1, 1965

By A. W. Khair, M. Ahmad, L. D. Gehl

"This paper presents an analysis of the dynamics of bit wear on the productivity of the continuous miners. Two field surveys have been carried out. The first survey was to assess the impact of bit wear on productivity and production cost. The second survey was to study the wear characteristics of the cutting tool (i.e. magnitude, forms, and mechanisms of bit wear). Primary factors affecting bit wear is identified and laboratory experiments were carried out to study the effects of some of these primary factors on wear in detail. Results indicate that bit wear has a significant effect on the productivity of the continuous miners. Furthermore under the severe geologic conditions (i.e. cutting rock partings and roof and floor rocks) bit wear not only hampers the productivity, but also increases the production cost due to a higher number of bit consumption. This study also indicated that bit wear accelerates beyond 20% of the conical height loss which corresponds to 7% of the weight loss. This increase rate of wear is an indicative of higher abrasion between bit body and cutting material, resulting in a more dusty environment.IntroductionThe high demand for coal production has increased the need for mechanized coal cutting in underground coal mines. Continuous miners have been used in the United States of America for nearly four decades and now presently more than 2000 are in operation. Almost half of the underground coal production of the country is by continuous miners. Today, competition in the coal industry has increased, due mainly to market conditions and legal restrictions, thus placing an emphasis on production, efficiency, and safety. The use of continuous miners has resulted in the generation of respirable coal dust which causes black lung in mine workers. On the other hand, bit wear presents a serious problem as it affects productivity and economy.Much research in the put has been done on energy requirements and mechanism of energy dissipation for ideal rock fragmentation in the cutting process. Recently, dust hazards in underground coal mines as a result of coal cutting has been a great concern to mining engineers as well as environmentalist of the country. In past, much emphasize has been given to fragmentation mechanics (Khair et al, 1989), dust generation due to regrinding (Khair and Xu, 1991) and dust generation due to bit wear (Khair, Xu. and Ahmad, 1992). These studies concluded that dust concentration increased considerably after a bit weight loss of 7% and thereafter the bit should be replaced. Thus, legal restriction by the Mine Health and Safety Administration for the respirable dust concentration in underground might be a factor deciding the level or rate of production using continuous miners. While efforts in research are on reducing dust generation, it is also important and relevant to study bit wear in more detail.Bit wear is affected by three major groups of parameters: (1) machine operating parameters, (2) insitu conditions and (3) properties of rock. Again, past studies have shown that depth of cut, material of tool, position of water jet and velocity of the rotating drum are very important machine operating parameters. The content of the rock/coal material is important as bit wear is usually due to abrasion or adhesion. Diffusive wear becomes dominant only when the temperature exceeds the sensitive range i.e critical temperature. Mechanical tools have indicated that a rise in temperature is a function of drum velocity, properties of cutting material (rock or coal) and properties of tool. Bit wear due to chemical reaction and oxidation art almost negligible in coal cutting."

Nov 1, 1995

By J. S. Dunning

Recent developments in energy conversion, mining and minerals processing, pollution control, and chemical equipment have placed in-creased demands on heat-resistant alloys. Higher corrosion rates from oxidation, hot corrosion, and sulfidation have increased consumption of materials that contain critical and strategic minerals and in many cases have limited productivity. The Bureau of Mines is conducting re-search on substitute materials having greater resistance to high-temperature corrosive atmospheres above 6000 C compared to austenitic stainless steels such as AISI 304, 316, and 310, with the goal of conserving critical metals such as Cr and Ni. The substitute materials are based on Fe-Cr-Ni-Al compositions. Aluminum additions to Fe-Cr-Ni alloys significantly improve high-temperature corrosion resistance, particularly sulfidation resistance. In the alloy, devised by Bureau researchers, aluminum additions are held in the form of a second-phase precipitate, 8NiAl. Minor additions of Ti, Mn, and Si improve workability.

Jan 1, 1984

By Richard L. Unger

Equipment is the primary cause of injury in 11% of all mining accidents and a secondary cause in another 10%. Purchasers should select new equipment carefully to ensure that the machine incorporates good ergonomic design criteria that maximize the safety of their mine workers. One potential problem area is the workstation-the control center of the machine. Safety problems often occur when the workstation provides insufficient clearance or visibility to the operator or has controls that are difficult to reach. This is especially true for underground mines, where confined space is an issue. In reclined or stooped postures, operators will have less strength and agility and often experience reduced visibility. We have conducted and published much research in Human Factors design of mining machine workstations. This information is currently being compiled into a series of Human Factors design recommendation reports. The reposts dl cover many topics, including workstation layout, control design, seating, and visibility. Each topic has a list of basic or first principles of design. Understanding these principles is the key to designing or purchasing a workstation that is both safe and efficient. Following is a sampling of these main topics and first principles.

Aug 1, 1996

By Alan D. Hartman

Instabilities in electric steelmaking furnace arcs cause electrical and acoustical noise, reduce operating efficiency, increase refractory erosion, and increase electrode usage. The U.S. Bureau of Mines is investigating methods to stabilize these arcs. To perform experiments to test new hypotheses, Bureau researchers designed and instrumented an advanced, experimental single-phase furnace. This report describes this furnace, which was equipped with high-speed data acquisition capabilities for electrical, temperature, pressure, and flow-rate measurements; automated atmosphere control; ballistic calorimetry; and view ports for high-speed cinematography. Precise environmental control and accurate data acquisition allow the statistical design of experiments and assignment of rigorous confidence limits when potential furnace or procedural modifications are tested.

Jan 1, 2010

By Alexander E. Morrow

Oxygen breathing apparatus for use in mines was introduced to the United States in 1907. Despite their intended purpose of safeguarding lives, the apparatus led to the deaths of many men because of inherent or developed defects in the equipment, lack of training,, physical shortcomings of wearers, and improper procedures. The Bureau of Mines pioneered in research and training to curb logs of life among users of such apparatus and promoted development of safer equipment and procedures. As a consequence, deaths have been far less frequent. In 1944 the Bureau issued Information Circular 7279, Loss of Life Among Wearers of Oxygen Breathing Apparatus. That publication listed the case histories of 26 deaths that had occurred since the introduction of such equipment to American mining. The author, the late G. W. Grove,3/ asserted that further loss of life could be avoided if good equipment were used, teams were properly trained, and the basic principles of safe procedure were followed. This publication is a sequel to I.C. 7279 and contains information on eight deaths among wearers of oxygen breathing apparatus that were overlooked in the original compilation. It also describes the single death that occurred since I.C. 7279 was published.

Jan 1, 1959

By Roy C. Bartholomae

This U.S. Bureau of Mines study found that the performance of the active noise cancellation hearing protector in a reverberant field was mixed. The performance varied when the conditions changed from ideal to nonideal. The active noise cancellation (ANC) component provided substantial additional noise reduction from 125 to 500 Hz for all testing conditions (broadband noise or pure tones both with and without safety glasses). While the ANC under ideal conditions provided additional attenuation from 500 Hz and below, under nonideal pink noise conditions the ANC amplified noise below the 125-Hz third octave band. There was a middle band of frequencies at which the ANC amplified noise levels ranging from 630 to 4,000 Hz. The results for pure tones showed that attenuations were higher but that they followed the same general trend.

Jan 1, 2010

By A. D. Bauer

For several years the Bureau of Mines has conducted surveys to determine the changes in motor gasoline being sold throughout the United States. The present survey shows that far the districts in which samples were collected, the average gasoline is becoming more volatile instead of less so, as is sometimes supposed. This year's gasoline is much more volatile than that sold two years ago, and it has a somewhat better distillation range than last summer's samples. A comparison of the average figures for several years, shows that motor gasoline is also becoming more uniform in character. The large seasonal change is disappearing, but ?winter gasoline', still has a lower initial boiling point than "scanner gasoline". This difference in volatility is made intentionally to facilitate starting the motor in cold weather. The end point shown in the present survey is slightly lower either than that of last winter or of the summer of 1921.

Jan 1, 1922

By Jack D. Ramsdell

The objective of this investigation was to make a preliminary evaluation of titanium-vanadium-zirconium, alloys using room-temperature tensile properties as criteria for selecting promising alloys for future critical studies. Arc-melted titanium-vanadium-zirconium alloys ranging in composition from 5 to 20 a/o (atomic-percent) vanadium and 5 to 30 a/o zirconium, were investigated to evaluate hardness, hot workability, and room-temperature tensile properties. Metallographic examination coupled with hardness measurements were used to follow structural changes and aging response. Room-temperature tensile properties were criteria for evaluating mechanical and engineering properties of the alloys.

Jan 1, 1960

By A. W. Deurbrouck

The Bureau of Mines analyzed 13 samples collected from three Randolph County coalbeds. The Peerless and Sewell bed samples were generally of metallurgical quality as received from the mines or could be easily upgraded. How-ever, the Lower Kittanning coa1bed samples proved to be quite inimical to upgrading to metallurgical quality.

Jan 1, 1966

By M. J. Friedel, D. F. Scott, T. J. Williams

In an effort aimed at monitoring mining-induced stress changes that may influence ground failure, the US Bureau of Mines conducted a series of active 3-D seismic tomographic surveys at the Homestake (Lead, South Dakota) and Lucky Friday (Mullan, Idaho) mines. Existing rock bolts were used to mount geophones and as strike points for introducing seismic energy using a 3.6 kg sledge hammer. Travel time measurements were recorded spanning up to 160 m between drifts at several levels. The tomographic uncertainty was minimized by computing iso-velocity surfaces of constant probability based on statistics from multiple reconstructions and a threshold criteria. Periodic imaging using tomographic velocity surfaces demonstrated that temporal and spatial changes in the local stress field occurred in response to ground failure and stope advancement at a gold and silver mine, respectively. Keywords: Temporal imaging; Mine-induced stress; Seismic tomography; Geophysics

Sep 9, 1996

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered equipment and subassemblies approved and certified by the Bureau of Mines for use in noncoal mines. Testing of diesel-powered equipment is one phase of the Bureau's program of health and safety that concerns approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, or toxic hazards in underground mines, when such equipment is used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study of their design, safety features, and use. Equipment must pass exacting tests and must meet strict requirements established through research and experience and listed in the Bureau's permissible schedules before the Bureau approves it as permissible for safe use in mines.

Jan 1, 1963

By W. D. Riley

The Bureau of Mines is conducting research on methods for the rapid identification and sorting of mixed scrap metals and alloys so that domestic scrap resources can be fully utilized. One method, spark testing, is the examination of the pattern of sparks that results when a metal or alloy is ground on an abrasive wheel. This technique requires experienced sorters. Bureau researchers have shown that spectrophotometric methods can be used in lieu of the highly skilled sorter. The spectra of a mild steel, an HSLA steel, several stainless steels, and four nickel-base alloys have been measured. Differences in the spectra that are sufficient for identification are apparent.

Jan 1, 1985

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered equipment and subassemblies approved and certified by the Bureau of Mines for use in noncoal mines. Testing of diesel-powered equipment is one phase of the Bureau's program of health and safety that concerns approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, or toxic hazards in underground mines, when such equipment is used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study of their design, safety features, and use. Equipment must pass exacting tests and must meet strict requirements established through research and experience and listed in the Bureau's permissible schedules before the Bureau approves it as permissible for safe use in mines.

Jan 1, 1963

By Robert P. Vinson, John C. LaScola, Fred N. Kissell, Edward D. Thimon

The face ventilation measurement method developed by the Bureau of Mines involves releasing a small volume of tracer gas (SF6) on the off-curtain side of the working face at the start of the mining cycle. At the same time, gas bottle samples are taken in the immediate return airway. The gas samples are analyzed, and a curve is drawn of SF6 concentration versus time. From this curve, the percentage of gas removed per time is calculated. A curve showing a high percentage of the tracer gas removed in a short period would represent a well-ventilated face. The face ventilation measurement method was tested in a full-scale mine entry model. Subsequently it was used underground to evaluate the spray-fan ventilation system and in an MSHA test facility to test machine-mounted scrubbers. The method was shown to be a simple and effective way of evaluating face ventilation systems.

Jan 1, 1980

By T. M. Klemetti, G. M. Molinda, D. M. Pappas

Some of the most difficult coal mine roof in the U.S. can be found in the Illinois Basin. Factors contributing to the high roof fall rate include: weak moisture-sensitive roof rock, high horizontal stress, and limited longwall mining. The depth of cover ranges from 90-1,000 ft and roof damage from horizontal stress can be severe. Moisture sensitive-roof rock is common above the Springfield-Harrisburg Herrin #5 and #6 seams in the Illinois Basin, and contributes to roof skin deterioration. The roof fall rate increases significantly in the humid summer months. The National Institute for Occupational Safety and Health (NIOSH) has shown, using lab and field studies, that highly moisture-sensitive roof rock can be directly correlated to poor roof conditions. Controlling the skin is the key to reducing rock fall injuries, and roof screening is, by far, the best remedy. Illinois Basin coal operators have been successful in reducing the number of rock fall injuries in recent years. NIOSH has documented best practices for screen installation which has resulted in safe, efficient operations. Other solutions to skin failure include: the use of denser five bolts per row patterns to reduce spans between bolts, systematic supplemental support in intersections, straps and large pans protecting operators, and air conditioning to remove moisture from the intake air.

By Suresh K. Bhatt

A mathematically simulated modeling technique is used in this U.S. Bureau of Mines report to represent a hypothetical mining operation with existing mining technology and prevalent mining costs. Mining scenarios were prepared and evaluated for potential benefits and costs available through computer-assisted mining. Base criteria, parameters, and methodology are described.

Jan 1, 1991

By Jeffrey M. Listak

The Bureau of Mines has conducted a rock mechanics study to monitor deformation of near-seam strata above a longwall panel in the Pittsburgh Coalbed. The primary goal was to determine the height of caving immediately behind advancing longwall face supports. This study, although site specific, provides information on the caving mechanism associated with longwall extractions so that strata behavior and its interaction with longwall face supports can be better understood. Two holes were drilled, approximately 550 ft apart along the center line of a longwall panel, from the surface to the coalbed approximately 650 ft below. Various downhole geotechnical instruments were used to monitor strata deformation. In addition, surface elevation surveys were conducted to differentiate between surface and subsurface activity. This report discusses the caving characteristics of the strata as the longwall panel approached and passed beneath the boreholes. Physical property data are also presented to demonstrate the relationship between caving behavior and local geology. Data show that immediate caving of strata above the longwall face occurred at a height less than 23.5 ft and that strata behavior above longwall extractions is highly dependent upon lithology, with major disturbances occurring at weak lithologic zones.

Jan 1, 1986