Search Documents

By T. D. Moore

Methane emission from two surface gob-degasification boreholes was measured by the Bureau of Mines. The investigation took place during mining of a 3,200-foot longwall panel in the Lower Kittanning coalbed in central Pennsylvania. The first hole was 500 feet from the start of mining, and the second hole was 2,200 feet. The first hole went on natural draft as soon as the longwall face passed it. This caused the methane flow in the return entries to drop 75 pct. In the 6 months required to complete the panel, the two holes emitted 69 MMcf of methane in varying percentages of concentration in air. In 3 years, the holes emitted a total of 150 MMcf of methane.

Jan 1, 1976

No noticeable international economic recovery occurred during the first half of 1982. Industrial production continued to fall in the United States, Canada and Italy and to hold steady in France. Modest increases in production occurred in Japan, England and Germany, although some decline took place from March to April. The U.S. mining industry has been more severely affected by the world recession than the U.S. economy. This is not immediately obvious when comparing the U.S. mining industrial production index from 1981 to 1982, which decreased 8.5 percent, as compared to a 7.1 percent decline for total domestic industries. However, "mining" industry statistics in the U.S. national economic accounting system include petroleum and natural gas as well as minerals. When metal mining is isolated, the decrease in production from 1981 to 1982 is 19.3 percent. If metal mining production continues to perform at the same rate during the third and fourth quarters of 1982 as during the first half of the year, declines from 1981 levels will be quite severe. Aluminum will have declined 22 percent, copper 18 percent, iron ore 24 percent, lead 3 percent, steel 29 percent, titanium 2 percent and zinc 25 percent.

Jan 1, 1982

To improve mining safety and efficiency by providing a practical way of detecting faults and channel sands that disturb coal seams. Approach A seismic system using a shallow blasthole has been developed and tested. How It Works A small shock is caused in a shallow hole, sending seismic waves through the ground. These waves are reflected from the top of the coal seam, acid are detected by a line of geophones on the earth's surface. Dampening of the seismic signals by channel sands and other discontinuities in the seam is detected and recorded. See Figure 1. The seismic shock wave can be produced by exploding small charges, dropping a weight, firing a gas gun, or actuating a vibrator. Depending on the soil cover, the shock is usually generated in shallow vertical holes about 10 feet deep. Hole depth depends on the soil mantle thickness because it is preferable that the seismic shock originate below that layer.

Jan 1, 1976

By Edward M. Kawenski

Tests were made in the Bureau of Mines Experimental Coal Mine on stop-pings similar to those used in operating coal mines to obtain information on air leakage through the face and the rupture strength of a stopping subjected to a pressure differential. Block stoppings were made from cinder, slag, and gravel aggregates with and without mortared joints and coatings. Sheet stop-pings were uncoated brattice cloth and nylon or brattice cloth and expanded metal-lath coated with asphalt, latex, mortar, or rigid urethane foam. Limited data were obtained on air through stoppings subjected to simulated roof convergence and to shock forces created by the firing of an adjacent charge of explosive. The pressure differential required to rupture stoppings was determined. shows that coating the face of a stopping effectively reduces ail: leakage. Block stoppings, particularly those with mortared joints, are most resistant to pressure and shock forces than are sheet stop-pings. Where ground movement is a factor, sheet stoppings leak less air than block stoppings.

Jan 1, 1965

By G. M. Martinez

A cell concept adaptable to large-scale electrowinning of zirconium metal from zirconium tetrachloride was investigated by the Federal Bureau of Mines. Tests were made in twin cells, each 12 inches in diameter by 33 inches long. Electrowinning was performed in one chamber from which the electrolyte was transferred after electrolysis to the other chamber where it was renewed by the introduction of ZrC14 by direct sublimation. The formation of a salt plug in the connecting pipe provided a seal between the chambers. Optimum electrolyte composition, with respect to quality of the metal product (91 pct meeting ASTM standards except for the oxygen content) and current-carrying capability (about 350 amp) was determined to be 16.7 wt-pct NaF-83.3 wt-pct NaCl mixture plus ZrC14 equal to about 3 wt-pct zirconium. A twin-cell design incorporating the unit operations covered by this investigation is proposed.

Jan 1, 1976

It was decided to demonstrate the use of latex as a soil sealant by irrigating three small plots at Lanse coded 03A on the west of Brown's run, 3C on the east of the stream, and SB, an area on the spoil bank. Earlier plans to sprinkle latex on twenty acres of the side were abandoned because of easement difficulties. On the basis of results from laboratory soil columns and small plot experiments at Lanse, Naugatex J-3471 was the latex of choice. The irrigation system consisted of plastic pipe (two inch size) for the main line from the water meter to the irrigation area because of lower price and ease of handling. Because the municipal water supply was limited to 20 gpm, low-volume 14V-LA-TNT Rainbow sprinklers were specified with low angle 20° 3/32 inch nozzles to reduce wind effects. At the expected nozzle pressure of 50 psig, each sprinkler covers a 56 foot diameter area at a delivery rate of 1.64 gpm. Each of the three test areas was covered with twelve sprinklers, six used with water alone as a control area and six used with latex and subsequent water spraying. One-quarterturn inlet valves were positioned on the main lines leading to each area. Flow to the treated and untreated areas was set at 10 gpm by Dole flow control valves in the' main entry lateral to each of the six sprinklers. To avoid the use of dilution tanks, a Moyno pump operated by a 1/2 HP, 1140 rpm 5:1 reducing drive was used to deliver 1/2 gpm 48% latex for mixing with 10 gpm water. A 3500 watt gasoline generator provided power for pump and light. Latex was applied at night to take advantage of the lower evaporation and higher humidity. Neutron gauge access tubes were placed in orthogonal arrangement in the areas that were irrigated, with four tubes in the section that were sprinkled with latex and four tubes in the untreated irrigation section in each of the three locations. Each tube, five and one-half feet long and sealed at one end with a plug welded in place, was inserted five feet into the ground in a cored hole. In each irrigation area, the left section of six sprinklers spread the dilute latex while the right section sprinkled the same amount of water to serve as a control plot. As shown in Figure 7 each sprinkler has a 56-foot sprinkling diameter at 50 psig design water pressure. The sprinklers are 30 feet apart on the laterals and 35 feet apart between the laterals. The access tubes (coded AT on Figure 7) were placed in comparable spots on the two sections of each area, so that four soil moisture measurements on the two sections could be compared. Bouyoucos resistance blocks (BB) were also placed in areas 03A and 3C at one, two and three foot depths, but not on the spoil bank area.

Jan 1, 1972

In 2006, a total of 741 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 These mines (e.g., potash, gypsum, salt) comprised 5.0% of all operations. ? Mines producing common clay comprised 25.2% (n=187) of all nonmetal mining operations. ? Nonmetal mining operations were located in all states and territories except Alaska, Delaware, Hawaii, Maine, New Hampshire, Rhode Island, Puerto Rico, and the Virgin Islands.

Jan 1, 2008

By M. J. Friedel, D. E. Scott, T. J. Williams

Rock masses in deep level mines are subject to high stresses, which can result in unexpected failure of rock into mined-out openings. Historically, various independent methods have been used to discern the causes of rock bursts and to evaluate stress conditions in rock masses susceptible to violent failure. Personnel from two research centers of the former U.S. Bureau of Mines, Spokane and Twin Cities, investigated a rock burst that occurred in May of 1994 in a rock mass between the 4400 and the 4600 levels of the Sunshine Mine, Kellogg, ID. The team evaluated the current state of stress in the pillar and the most likely cause of the rock burst by studying the seismic history of the pillar, examining the geology, analyzing the available in situ stress data, calculating possible fault-plane solutions for the burst, and performing a seismic velocity tomographic survey. The results of the study showed that post-rock-burst seismicity was concentrated about 15 to 30 m west of and about 15 m above the rock-burst location. The pillar is composed of a very hard sericitic-to- vitreous quartzite of a type rarely found in the mine, but that is often found in other district mines having a history of seismic activity. In situ stress analysis of the pillar and the surrounding rock mass showed a probable stress rotation from northwest-southeast to east-west. Of four fault plane solutions, the most probable was either a left-lateral, strike-slip movement with a compressive principal stress oriented nearly north-south, or a right-lateral, strike-slip movement oriented east-west. Finally, tomographic images showed low-velocity areas (interpreted as areas of low stress) associated with the crosscuts and haulageways, and high-velocity areas (interpreted as areas of high stress) associated with the rock-burst location. High velocities were also found in a planar area oriented in an elongate northeast-southwest direction.

By H. S. Caldwell

Molten zinc, condensed from zinc vapor, was used by the Federal Bureau of Mines to leach aluminum from an aluminum-silicon alloy made by carbothermic reduction of silicious aluminum ores. Zinc requirements were minimized by re-fluxing condensed zinc in a low-pressure, Soxhlet-type distillation unit. The minimum ratio of zinc used to aluminum in the crude alloy was approximately 2:1. When the system pressure was reduced from atmospheric pressure to 100 microns or less, the rate of aluminum extraction increased by a factor of 20. Leaching rates were much higher when the zinc vapor was condensed directly on the crude alloy than when molten zinc was passed over the alloy in the absence of appreciable zinc vapors. Observations indicated higher extraction efficiencies from crude alloys containing greater amounts of iron. Complete extraction was obtained with negligible loss of zinc. Assuming complete removal of zinc, the aluminum products will contain 1 to 6 percent silicon and about 0.5 percent iron plus titanium. The leached crude-alloy residue is a highly friable spongelike material containing about 80 percent silicon, several percent iron and titanium, with the remainder aluminum. This extraction method has been patented (Patent 2,810,637) and assigned to the Government. Research and development investigations are continuing at the College Park Metallurgy Research Center.

Jan 1, 1961

By Steven J. Page

The Bureau of Mines used fiber-laden air to test two identical fibrous aerosol monitors (FAM) in order to establish the FAM-optical count correlation. The FAM is a unique instrument developed by GCA Corp. (GCA) to measure real-time fibrous aerosol concentrations. It will also respond to particulates that have sufficient shape irregularities to possess fiber characteristics such as the 3:1 length: diameter (L:D) aspect ratio. Results of the Bureau's laboratory tests showed that the FAM response is linearly correlated to concentration data obtained using the optical membrane filter count technique approved by the National Institute for Occupational Safety and Health (NIOSH), U.S. Department of Health, Education, and Welfare. A plot of the FAM-optical count correlation showed that FAM concentration readings are generally well within ±25 pct of the optical membrane filter count. Initial tests to estimate the best ratio control setting of the FAM for 5-µm fiber-length discrimination were performed using one instrument only (the ratio control setting determines the minimum threshold fiber length that will be detected by the FAM). The estimated setting was then used to correlate both FAM units. The result was a 65 pct difference in correlation between the two units. It appears that the major factor responsible for this difference was the internal adjustment of the photomultiplier detector sensitivity for each of the two FAM units.

Jan 1, 1980

By Edward F. Divers

A new nonclogging water spray system for continuous-mining machines has been developed under contract with the Bureau of Mines. This paper presents installation and operating guidelines for the system, which consists of improved and easily maintained machine-mounted hardware, including an inline Y-strainer, a hydrocyclone, a backup filter, and two quick-opening valves for flushing particulates from the strainer and hydrocyclone. Underground tests with continuous-mining machines have shown that when properly installed and maintained, the new sys tern virtually eliminates nozzle clogging and thus greatly reduces spray maintenance. The sys tern is relatively inexpensive and has been installed on typical continuous-mining machines for a total cost under $1,000.

Jan 1, 1976

By P. G. Clites

A laboratory furnace was developed by the Federal Bureau of Mines for use in studying the interrelationships among variables associated with skull melting and casting high-temperature metals. Although additional work is necessary to determine the extent to which the information obtained by using this furnace can be extrapolated to larger furnaces of the same type, many casting characteristics of metals and alloys can be determined on equipment of this size. This furnace is a laboratory-size, consumable-electrode, skull-casting furnace equipped with a water-cooled copper ladle. The ladle, which is a tilt-pour or over-the-lip type, has a volume of approximately 30 cubic inches and provides up to 20 cubic inches of molten metal for castings. Castings of various reactive and refractory metals, including zirconium, titanium, hafnium, columbium, molybdenum, tantalum, and tungsten, have been produced. In addition, castings of iron, chromium, and copper have been made. The simplicity and versatility of the apparatus would make it useful to metallurgical laboratories preparing cast specimens.

Jan 1, 1961

By James R. Aggson

This Bureau of Mines report presents a finite element analysis of roof stresses associated with a 4-foot-high by 18-foot-wide underground coal mine entry. This analysis starts with known loading conditions determined in an underground coal mine in West Virginia and is extended to other possible underground loading conditions. The roof failures predicted by the finite element analysis under known loading conditions correlate well with the roof failures observed underground. The most probable failure modes are identified for the various loading conditions considered. Various failure preventive measures are discussed.

Jan 1, 1979

By Kenneth M. Smith

The kaolin deposits of Aiken County, South Carolina (fig. 1), have been worked continuously since 1852. It has been long known that the deposits contain a high percentage of' alumina and that large reserves exist. These facts led to the early selection of' this area for examination in the search by the Bureau of Mines for high-alumina clays. An exploratory program was started by the Bureau, and drilling was carried on from. June 27, 1942, to October 31, 1942. The kaolin-bearing district occupies an area approximately 25 miles long and 11 miles wide, running northeast, with its center at Aiken, S. C. (fig. 1). Within this district, a triangular area bounded by Horse Creek, Silver Bluff Road, and Hamburg Road was roughly prospected by boring 43 machine and 12 hand holes. As a result of the data obtained, a final smaller area was chosen for more systematic prospecting. This area is bounded by Pine Log, Tewkesbury, Silver Bluff, and Craig Sawmill Roads and covers about 4,000 acres. Mineral exploration agreements covering 11,272 acres were signed by 35 property owners, and 11,956 feet was drilled in 200 holes on these properties.

Jan 1, 1949

By Robert A. Jankowski

The U.S. Bureau of Mines, in cooperation with the Mine Safety and Health Administration (MSHA) and the mining industry, has identified and demonstrated the effectiveness of several improved face ventilation techniques for longwall mining systems. These include the following: identifying improved techniques for measuring face ventilation parameters on longwall sections, installing curtains at the intake end of the longwall face to maximize usage of the primary airflow, identifying optimum face airflow rates for maximizing dilution effects, and coursing the primary face intake from tailgate to headgate to minimize outby airflow contamination. Application of these techniques throughout the mining industry should reduce the health hazard associated with excessive exposure to respirable coal mine dust.

Jan 1, 1993

By Harold W. Lipper

Helium production and shipment reached new peaks in 1.361. The Bureau of Mines produced 727 million cubic feet, 13 percent more than the 1960 record, and shipped 552 million cubic feet, 16 percent more than the 1960 record. Production exceeded demand for the third successive year, enabling the Bureau of Mines to add 174 million cubic feet to the volume stored underground for future use. At the end of 1961, the total volume of helium in underground storage in the Clifside gasfield was 44-7 million cubic feet. Contracts to implement a long-range helium conservation program were completed with four companies, obligating all the contracting authority of $47.5 million a year made available by the Congress. The four companies will finance, build, and operate helium extraction plants to recover from natural gas an annual average of 3.1 billion cubic feet of helium that would ordinarily be wasted when the helium-bearing natural gas is used for fuel.

Jan 1, 1962

By Robert J. Anderson

"Introductory Statement.In founding any kind of castings, even with the best practice, scrap castings are produced because of rejections for certain defects. Casting los¬ses are a serious source of financial loss in iron and steel foundry practice as well as, in brass and bronze, but they are particularly serious in aluminum foundry work because of the high value of aluminum. The indications are that in many aluminum foundries in the United States, the casting losses are at times high, and in some plants they are entirely too high when compared with average practice. Of course, defective castings have a residual value for remelting, but if much machine work has been done on a casting before it is scraped, the labor costs alone may exceed the value of the metal and even that of the rough casting.In a foundry, the monetary losses incurred through the production of waster castings can be ascertained from calculations based upon adequate scrap-loss reports. Such reports, when properly kept and interpreted are a valuable aid in finding foundry costs, but they are primarily useful in diagnosing the causes for casting losses. Many aluminum foundries in the United States do not keep adequate records of strap losses; as a result the causes for defective castings can not be traced, nor preventative measures adopted. However, some of the large aluminum foundries keep excellent records, and it has been found that these involve little extra expense for clerical work. If a foundry man will study his daily production of defective and waster castings, he will be able to trace the causes or losses and then make such corrections in his plant practice as will effect a considerable reduction in these losses -- as much as 50.0 per tent in some foundries. If all the present casting losses of the United States could be reduced 50.0 per cent, by eliminating only the readily preventable defectives, a saving of several million dollars would accrue. In the aluminum-foundry industry alone, the saving would amount to about $600,000."

Apr 1, 1920

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations within a multiple-seam configuration. A comparative study was performed at two separate mine sites. The objective of this study was to compare two mines, each affected by this pillar load transfer mechanism, and to show how this interaction affected underground workings by the installing and monitoring underground instrumentation. At mine site A where the overburden was 1,000 ft, the innerburden thickness was less than a pillar width (40 to 45 ft), overlays of the mine layout show pillars were not superpositioned, excessive roof to floor convergence was measured, and pressure readings indicated pillar core loading only. At mine site B, the overburden was approximately 555 ft, the innerburden thickness was approximately 105 ft, overlays of the mine layout show pillars were superpositioned, minimal roof to floor convergence was measured, and pressure readings indicated a skin loading only.

Jan 1, 1988

By Van E. Shaw

Fusion of an 86-percent euxenite concentrate with ammonium sulfate was investigated by the Bureau of Mines. Reaction for 4 hours at 400° C results in conversion of both the rare-earth elements and the titanium-columbium components to water-soluble compounds. Similar results are obtained with ammonium bisulfate. Stirring the fusion mass decreases the reaction time substantially. Alternatively, treating the fusion product with a 3-hour, 650° C calcining step renders the non-rare-earth constituents insoluble, thereby allowing selective leaching of a pure rare-earth fraction with an overall yield of 97 percent.

Jan 1, 1967

Reliably measure stress chan¬ges in order to assess stability of mine openings. Approach: A durable, permissible, sensor and readout system have been developed and tested. How It Works: The stress sensing element is a taut steel wire which is, vibrated at its natural frequency, If the tension on the wire is changed because of deformation of the sensor housing, the natural frequency of the wire changes. This effect is similar to decreasing or increasing the pitch of a violin string by loosening or tightening it. Because the stress sensor electrical output is a frequency signal, rather than an amplitude signal, its accuracy is unaffected by the resistance of the signal wire, or other attenuation. Signal wires can be a mile or longer without affecting accuracy. When a button is pushed on the readout box, the sensor wire is electromagnetically excited and vibrates at its natural frequency. That signal causes a readout in illuminated digits. (By referring to calibration chart and the previous reading, the user knows the change in stress.) This system is permissible. To install the sensor, a slightly oversize hole is drilled into the mine pillar. Next, a special tool is used to both position the sensor and wedge it in place. Figure 1, shows the sensor and its integral wedge and hole-fitting piece.

Jan 1, 1976