Search Documents

By M. R. Geer

The Bureau of Mines surveyed the solid wastes that have accumulated from coal mining in Washington, Oregon, and Montana. Location, amount, character, and condition were determined, and both economic and environmental factors were considered. Areas covered by waste comprise 800 acres in Washington, 5 acres in Oregon, and 1,200 acres in Montana. In a few cases waste is being utilized, particularly cinder from burned refuse dumps, as fill in road construction and as a ceramic raw material. It is estimated that wastes deriving from coal mined for electric power generation by 1974 may amount to 3 million tons of washery refuse, 2.7 million tons of fly ash, and 1,000 acres of spoil banks.

Jan 1, 1969

Aid mine operators as well as mine inspectors in making quick but sufficiently accurate measurements of the rock dust content of coal/rock dust mixtures. The Problem Past research has shown that accumulations of volatile coal dust in underground coal mines can be rendered non-explosive by dilution with chemically inert rock dust (usually limestone). Consequently, rock dusting is required by law in U.S. underground coal mines. However, mine officials and inspectors have no quick and reliable means to determine whether enough rock dust has been applied to achieve a mixture that is in compliance with the law. Even the compliance tests used by the Mine Safety and Health Administration (MSHA) are slow and involved. MSHA assures that a mine has been rock dusted adequately by collecting samples from rock dusted areas of the mine and sending the samples to a laboratory for analyses of the inert-dust content. The analyses may not be completed for more than two weeks, during which time the mine in question might be inadequately protected against coal dust explosions. To solve this problem, the Bureau of Mines devised a quick, simple and reliable device that can immediately determine the rock-dust content of a mixture of coal and rock dust.

Jan 1, 1985

By J. N. Tomlinson

Trailing-cable splices are evaluated for moisture exclusion abilities after repeated travel over shuttle-car sheave wheels. Tests are conducted on cables with jackets made of neoprene, cholrosulphonated polyethylene (CSPE), and nitrile butadiene-polyvinyl chloride (NBR-PVC) to 50° C. The results show that some splice kits are effective as received, others are improved with minor but significant changes, and still others must be redesigned to be effective in underground applications. Laboratory results are compared with actual underground splice results. Recommendations for cable preparation prior to splicing are presented.

Jan 1, 1979

By R. J. Leary

Oxidation testing of copper-clad steel strip was performed in a muffle furnace to determine whether copper in contact with steel scrap could be removed by oxidation in an airstream at high temperatures. Substantially all of the copper was oxidized before any significant iron oxidation occurred. The rate of copper oxidation was not affected by contact with iron. Copper oxide scale separated spontaneously from the underlying metal during cooling. Results indicate the possibility of removing light-gage copper coatings and components from ferrous scrap by oxidation in an incineration process.

Jan 1, 1965

By Earle S. Burnett

Rotating piston deadweight gages have been used for many years for measurement of pressure to several hundred atmospheres. They have been calibrated by comparison of fluid pressures produced by various loads bearing on the piston bases, as measured by corresponding heights of balancing columns of mercury. When expressed in appropriate units, these ratios of column heights to piston loads are called piston constants. Experimental arrangements and procedures for their determination are presented in this paper, followed by a discussion of their significance and of their subsequent applications.

Jan 1, 1966

By SUMNER S. SMITH

Mine inspection in Alaska by the Federal mine inspector was somewhat handicapped during 1915,the inspector having to spend a large part of the summer and fall in examining the Matanuska coal field in connection with the designation of the Government reservations and the leasing units in that field. However, in addition to>this work, the mines in southeastern and southwestern Alaska were inspected by both Federal and Territorial inspectors, a considerable number of men near the Federal inspector's officeat Juneau were trained in first aid to the injured and in the use of mine rescue apparatus, the mines of the interior and of Seward Peninsula were inspected by the Territorial inspector, and a suit was brought in the name of the Territorial inspector for the nonreporting of serious accidents under the Territorial inspection law. The work of the Federal inspector was handicapped also by a lack of field assistants. This condition is likely to be serious, as preparations have been made for opening the Matanuska, Bering River, and Nenana coal fields, and a number of permits granting the free use of 10-acre tracts in other fields throughout the Territory have been issued. The need of a comprehensive inspection law and experienced engineers to safeguard the opening of coal mines by operators who are not familiar with coal mining and are using inexperienced help is obvious.

Jan 1, 1917

By T. T. Campbell

A survey of the literature eras made covering the use of aqueous non-aqueous, and fused-welt systems for the electrowinning or electroplating of molybdenum metal. The survey was prepared in order to provide background for further investigations directed toward the electrodeposition of pure molybdenum metal from either aqueous or nonaqueous mediums. While a thorough effort was made to cover all available references, a critical review was not attempted nor does this survey pretend to be exhaustive in nature.

Jan 1, 1955

By E. R. Cole

A lead smelting process that appears to present minimal pollution problems has been developed at the Bureau of Mines, Rolla Metallurgy Research Center. Ten and 100 g samples of PbS mill concentrates were vaporized at 1,000° to 1,100° C in a furnace with an inert gas atmosphere during a 2-hour period. The PbS vapor was transported by the inert carrier gas to the reduction zone of the furnace where it was reduced at the same temperature with excess hydrogen to metallic lead. Lead of 99.9 pct purity was produced. The H2S formed can be decomposed into elemental sulfur and water vapor by a modified Claus process. Approximately 90 pet of the Cu and 70 pct of the Ag and Zn remain in the residue and are potentially recoverable. More than 98 pct of the lead in the concentrates was extracted.

Jan 1, 1974

By Clarence O. Babcock

This Bureau of Mines publication presents guidelines for mining near surface and underground bodies of water. The guidelines were based on information developed under contract in three phases of study, as follows: (1) Collection and documentation of data from worldwide sources; (2) application of existing guidelines, foreign, Federal, and State, to case histories of previous inundations; and (3) development of recommended guidelines for underground coal mining near bodies of water aimed at maximum efficient utilization of underground coal resources consistent with minimizing inundation hazards. While the contract guidelines were for the mining of coal seams, they may also be used for mining any tabular sedimentary mineral deposit. Tables are given for the determination of the size of coal pillars needed; for other bedded deposits, similar tables could be determined based on their strength properties.

Jan 1, 1977

By P. Yant, A. C. Fieldner

"IntroductionIn its investigations relative to reducing the hazards of carbon monoxide poisoning, the Bureau of Mines recently had its attention drawn to a compound2a sold under a trade name for which claims are reported to have been made regarding its efficacy in reducing that type of poisoning in automobile garages. Accordingly, some of the product was obtained and analyzed for its power to absorb, oxidize, or destroy carbon monoxide; and the results are herein reported.Description of ""Compound"" (quoted from manufacturer's circular)While the circular does not actually state that the ""compound"" protects against carbon monoxide, the inference is therein, because each of the two following quotations is below these respective headings; ""Carbon-Monoxide Poisoning,"" and ""Chronic Gassing Among Garage Workers.""The ""compound"" holds chlorine and oxygen gases in solution with formaldehyde, which unites with the hydrogen to form hydrochloric acid., giving an over-supply of oxygen which burns up carbon just as a piece of wood is burned in the fire. The formaldehyde in the composition of the ""compound"" is a great affinity for ammonia and hydrogen sulphide."

Apr 1, 1924

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937

Federal Regulations require MESA to regulate the exposure of workers to inhalation hazards in the surface work areas of coal mining and processing operations. (1) The purposes of this study are listed below: 1. Determination of candidate inhalation contaminants for surface work areas of coal mining and processing operations. 2. Selection of appropriate sampling and analytical methods. 3. Performance of qualitative surveys of 56 representative coal mining and processing facilities. 4. Preparation of handbook to provide guidance for inspectors sampling for these contaminants. This report describes the work which was done to accumulate the information which was used in preparing the inspector's handbook. Specifically, this report contains descriptions of the surveys which were performed, analytical results obtained from these surveys, findings and conclusions, and recommendations for additional research.

Jan 1, 1975

By H. J. Sloman

"INTRODUCTION Industry, including coal mining, has come to realize that to prevent accidents the human element must be given more consideration than was customary in the past. In formulating safety rules and regulations and in the enactment of laws governing mining, too often enforcement is emphasized rather than the means of gaining willing compliance.' The purpose of this paper is to call attention to the human side of accident prevention, and the approach to this important and much-discussed subject will deviate somewhat from the usual discussions.The human being is a complex mechanism, both physically and mentally. It is difficult to establish a common denominator for the actions of humans, except in general. In establishing mining laws, rules, regulations, and standards, the ultimate objective should be to gain the best possible response of workmen, so that optimum results in accident prevention may be obtained. The complexity of human beings is apparent when the many ways 1n which they differ are considered. Some of these differences are manifested in emotional and phlegmatic types, degrees of intellect or native intelligence; and in hopes, desires, aspirations, and philosophies of life. How much simpler ac¬cident prevention would be if the response to laws, rules, regulations, or standards were equivalent to the definite movements of puppets responding to pulls on strings. Each time, the strings are pulled in exactly the same way, the puppets will respond in exactly the same manner. Human beings, although having many similar characteristics, do not respond uniformly to identical ""string-pulling""; therefore, much study is necessary before the desired re¬sponses can be obtained. To achieve the ultimate in accident prevention, it must be ""worked at"" constantly. Regardless of the adequacy of safety laws, rules, regulations, or standards, good accident records will not ""roll in"" if dude consideration is not given to the personal traits of those most likely to be involved in accidents."

May 1, 1948

Comparative tests of four coals used industrially for coke production have been made by three laboratories of the Federal Bureau of Mines, each using its standard equipment and procedures for evaluating coal for coking. Two of the coals were blends used in the western and eastern sections of the United States, the third was a strongly coking coal widely used for producing coke in Alabama, and the fourth was a blend typical of those used for producing foundry coke in the Birmingham district. The coals used and the cokes produced from them covered a wide range of chemical and physical properties. The tests used at all three laboratories for determining the physical properties of the cokes were made according to ASTM (American Society for Testing Materials) methods. The excellent agreement found for the physical properties of the cokes indicated that, for the coals tested, the BM-AGA (Bureau of Mines-American Gas Association) 18-inch circular retort used at Pittsburgh, Pa" the 14-inch slot-type oven used at Denver, Colo., and the 17-inch slot-type oven used at Tuscaloosa, Ala., were substantially equivalent for evaluating coals for production of coke. Thus, added value is given to data obtained previously and independently at these three Bureau laboratories. INTRODUCTION Laboratory equipment to produce coke for evaluation has not been standardized by the industry. The results obtained with anyone design of equipment have been regarded as showing only the relative values of coal to produce coke of the requisite quality. Few systematic studies have been made to correlate results obtained in different types of equipment. Results of one, in which the Bureau of Mines participated, were published recently.2/ This

Jan 1, 1961

By P. G. Kovalchik

Safe electrical operation of shuttle cars depends upon maintaining the trailing cable's conductor temperature below 90° C. However, trailing cables are wound on and off reels, which changes the heat transfer characteristics of the cable-reel system. Derating factors for trailing cables are an attempt to adjust for this changing heat transfer mechanism in a practical way. The U.S. Bureau of Mines conducted research to determine acceptable derating factors for reeled mine trailing cables, using four cable-reel combinations, representative of industry usage. Cables were continuously and intermittently loaded at different duty cycles with direct currents of different magnitudes. Relationships between the average temperature rise and current load were established for each layer of each cable. Two models were constructed; one used empirical data from the continuous and intermittent load tests, and the other was based on thermodynamic theory. Results obtained from the theoretical model were compared with those from the empirical model for the rated temperature rise of the cable. Both models can be used to simulate a variety of test conditions including those that normally cannot be conducted in the laboratory. This information was used to determine acceptable derating factors for each layer of these cable-reel combinations.

Jan 1, 1994

Develop a more efficient method of testing the integrity of in-situ leach mining operations. The Problems For economic and environ-mental reasons, in-situ leaching operations must be sure that wells do not leak. Loss of solution in large quantities can be expensive in itself, and if such losses result in pollution the costs can be even higher. Wells are usually tested for leaks by sealing them with packers, pressurizing them and monitoring the pressure drop. However, many commercially-available packers are designed to be used in steel-cased wells rather than the fiberglass-or plastic-cased wells used for in-situ mining. These packers are heavy, cumbersome, expensive, and often leak. In addition, commonly used well-integrity-test systems require lengthy test periods and drill rigs or hoist trucks with rigid pipes must be used to run the packers in and out of the well. The Bureau of Mines has developed a mobile, self-contained leak-testing system that is faster, uses trailer-mounted equipment that can be operated by one person, and features a new inflatable packer.

Jan 1, 1985

By John J. Henn

As part of the U.S. Department of the Interior programs on rutile, authorized by the Office of Emergency Preparedness in June 1967 under provisions of the Defense Production Act, the Bureau of Mines reviewed available literature on major proposed processes for producing rutile substitutes. The processes are grouped according to the major processing step, and important operating features are described. Sixty-one references are cited.

Jan 1, 1970

By Alla D. Mah

No experimental heat-of-formation value has been reported in the literature for cerium sesquioxide. The heat of formation of bismuth sesquioxide has not been determined in recent years, and the older value was subject to large uncertainty. Accordingly, the heats of combustion of cerium sesquioxide and bismuth metal were measured by the Federal Bureau of Mines. The heats of formation were: ?H°298.15 = -427.01 ± 0.70 kcal. /mole for cerium sesquioxide and ?H°298.15 = -137.16 ± 0.30 kcal./mole for bismuth sesquioxide. The free energy of formation was estimated for cerium sesquioxide and accurately calculated for bismuth sesquioxide. The data were compared with values in the literature.

Jan 1, 1961

By Michael J. Magyar

This report contains a cost estimate of the Bureau of Mines process for dewatering Alaskan placer effluent streams with polyethylene oxide (PEO). In this process effluent slurry is withdrawn from the placer plant pond system after a primary settling stage. A dilute PEO solution is injected into the slurry line to flocculate the fine, suspended solids. The flocculated solids are dewatered on a stationary screen. Clarified water is returned to the placer operation or discharged, while the 35 percent solids waste is pumped back into the mine cut. Cost estimates are presented for dewatering plants processing 1,000 gallons per minute of effluent slurry at three representative turbidity levels. Both the placer and the dewatering plants operate on the same 1-shift-per-day, 6-day-per-week schedule for the 100-day Alaskan operating season. Estimated fixed capital costs for these plants processing placer with effluent turbidities of 1,000, 3,000, and 5,000 nephelometric turbidity units (NTU) are approximately $29,000, $31,000, and $34,000, respectively, on a fourth quarter 1986 basis. Operating costs are estimated to be $0.34, $0.37, and $0.40 per thousand gallons of effluent slurry.

Jan 1, 1987

Determine safe practices for surface mine blasting near pressurized gas, oil, and water transmission pipelines. Background Surface mine blasters regularly have to address the issue of how blasting affects transmission pipelines that run near and sometimes through their permit areas. Regulatory approaches to blasting have ranged from no regulation at all to strict limits intended to prevent cosmetic cracks in plaster interior walls of homes, but they have not directly addressed the impact of blasting on nearby pipelines. Concerned with both productivity and safety, the mining industry and its regulators have requested guidance on safe practices for mining near pipelines. The Pipeline Research Group of the American Gas Association has sponsored studies of the effects of small close-in blasts because of vibration concerns related to the installation of new pipes into existing pipeline right-of-ways. By contrast, the recent study in which the U.S. Bureau of Mines (USBM) took part is the first addressing large-scale mining blasts.

Jan 1, 1995