Search Documents

Etching solutions containing hexavalent chromium ions (e.g., chromic acid) are used in brass finishing, printed circuit board etching, preparation of plastic for plating, anodizing, and various other industrial surface treatment operations. As the solutions are used, hexavalent chromium ions are reduced to their trivalent state, contaminants accumulate in the solution, and the effective acid concentration is reduced. When the etching rate becomes unsatisfactory for the particular operation, the solutions are discarded. This is a problem because the discarded solutions are pollutants, and because replacing the etching solution is expensive. The Bureau of Mines has developed a process for regenerating these spent solutions and returning them to the surface treatment operation without interrupting the etching process. An electrolysis cell containing anode and cathode compartments that are separated by permeable membranes, is used for regenerating the spent solutions. The spent chromic acid solution is fed to the anode compartment and sui (uric acid is circulated in the cathode compartment. Application of a steady electrical potential of a few volts dc across the electrodes causes the copper ions and other contaminants in the spent solution to migrate through the membrane to the cathode compartment where copper is plated onto the cathode. Zinc and the other contaminants remain in the sulfuric acid. At the same time, the complex, trivalent chromium ions in the spent solution are attracted to the anode where they are oxidized to their original hexavalent state. The regenerated solution in the anode compartment is then recycled back to the plant?s etching operation for reuse.

Jan 1, 1980

By S. R. Borrowman

Physical beneficiation, leaching, and solvent extraction investigations were made to recover a high-grade thorium oxide product from Bald Mountain, Wyo., conglomerate. The monazite in the Bald Mountain deposit contains 8.8 percent Th02 and, therefore, is higher in thorium content than the usual domestic or foreign monazite. A sample of composited drill cuttings for the study contained 4.3 pounds of monazite per ton of are. The work showed that the monazite, although unusually fine grained and friable, could be concentrated by tabling and magnetic treatment to yield a product assaying 5.65 percent Th02 with a recovery of 61 percent of the thorium. Subsequent decomposition of the concentrate by treatment with sulfuric acid and solvent extraction of the resultant solution with a primary aliphatic amine yielded a thorium oxide product of 99-percent grade.

Jan 1, 1962

By J. L. Konchesky

The Bureau of Mines investigated the main reactions of coal gasification by steam. Coal (minus 70 mesh)-water slurry was fed into a laboratory-scale tube-coil gasifier to show the effects of residence time (0.6 to 1.1 sec), steam-coal ratio (2 to 11 lb/lb), and temperature (1,600° to 1,900° F), at about 1-1/2 atm. Devolatilization was very rapid: about 70 pet of the coal's volatile matter evolved within 0.6 sec at about 1,600° F; temperature increase released more volatile matter until about 95 pct was driven off at 1,900° F. Devolatilization was not increased by raising steam concentrations and was only slightly increased by extending residence time. Below 1,600° F, there was no evidence of the steam-carbon reaction, but at 1,900° F more than 80 pct of the coal's fixed carbon was converted to gas; the conversion was increased Significantly by increased residence time and steam concentration. The water-gas shift reaction occurred simultaneously with devolatilization, and the steam-carbon reaction, approaching equilibrium with increased residence time and temperature and decreased steam concentration.

Jan 1, 1969

By Roy Bartholomae

Noise generated by continuous mining machines in underground coal production is an important health hazard. Bureau of Mines Contract J0387229 covers investigation of this noise through laboratory tests of simulated cutting operations and through in-mine noise measurements. The results of these investigations indicate that coal cutting noise and conveyor noise are dominant sources of mining machine operational noise. Typical noise levels for both cutting and conveying operations are approximately 97 dBA (decibels A-weighted). For full operation of all machine systems, the overall sound pressure level is approximately 101 dBA. In-mine and laboratory test results show excellent agreement in both A-weighted overall levels as well as in A-weighted one-third-octave band spectra.

Jan 1, 1983

By William K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating the electrochemistry of mineral flotation. A significant need in this area is greater reliability of sensors. The USBM is testing electrolytic methods to clean and condition redox-sensing electrodes to improve the reliability and extend the service life of these instruments in the harsh physical and chemical environment of mineral processing slurries. A novel method for removing scale from fouled electrodes has been developed that includes anodic polarization to 1.2 V versus the Ag/ AgC1 reference potential, followed by brief potentiodynamic conditioning. Laboratory results show that this technique removes calcarious deposits from gold sensing electrodes and returns the electrodes to useful service within approximately 10 min. Mechanical abrasion to remove the scale is thereby avoided.

Jan 1, 2010

By LB. Berger

"INTRODUCTION The use of gasoline engines as the motive power for lift trucks, tractors, and other types of mobile equipment operated in enclosed spaces, such as industrial plants and warehouses, may create a hazard because of the carbon monoxide present in the exhaust gases of the engines; gasoline-powered equipment should not be used in mines or tunnels. Because the equipment is mobile, local ventilation usually is impracticable, and general ventilation of the spaces is nec-essary to dilute and remove the carbon monoxide. To estimate the rate of ventilation required in such situations, information is necessary on the concentration of carbon monoxide in the exhaust gas and the rate at which exhaust gas is produced under given operating conditions. The purpose of this paper is to present data that may be used in making estimates of ventilation requirements.COMPOSITION OF GASOLINE-ENGINE EXHAUST GASThe exhaust gas of a gasoline engine consists mainly of carbon dioxide, carbon monoxide, hydrogen, oxygen, and unburned hydrocarbons (usually reported as methane), together with the nitrogen present as a residue from the air sup-plied for combustion. 3/ The exhaust also contains water vapor resulting from combustion of the hydrogen of the fuel. The water-vapor content is not included in exhaust-gas analyses calculated on a ""dry"" basis and is not involved in the estimation of ventilation requirements."

Jun 1, 1947

By R. H. Schutz

TO ASSIST users in the selection of reliable and satisfactory respiratory protective devices, the Bureau of Mines bas established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules3 include 13D for self-contained breathing apparatus, 141F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pittsburgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer4 of the respirator and at his expense. If the device meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an extension of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines he used where respiratory protection is needed. The Bureau of Mines, however, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators.

Jan 1, 1966

By A. L. Murray, C. A. Allen

"In the Spring of 1919, the Industrial Commission of Utah undertook the assembling of safety orders covering metal mining operations Just at that time there appeared several articles in the mining papers advocating the licensing of hoisting engineers, so this subject was given careful consideration,The licensing of hoisting engineers means that they must pass an examination covering the mechanical features of hoists and boilers, and must have a certain amount of experience. This undoubtedly serves to get a class of hoisting engineers that are better informed about the mechanical operation and theoretical considerations in hoisting and the only room for argument against it is that it is difficult to give an examination that will determine whether or not a man is a competent hoisting engineer.A man might pass an excellent examination yet be absolutely unqualified to operate a hoist and the judgment of the mine super- intelligent would have to be depended upon to choose the right man from among those who were licensed. This difficulty of properly determining, by ordinary examination, a man's qualifications to run a hoist caused the idea of licensing' in the ordinary sense of the word to be abandoned; but, as there was no question that a hoisting engineer should be physically fit, it was decided to require a medical examination, and at the same time to require the hoist engineer to state his experience, so the State would better knowledge of his general qualifications.The orders covering the question were therefore issued as follows;"

Jan 1, 1920

Objective To characterize the roof fall risk associated with underground limestone mining. Background During the first 5 years of this decade, more than one-fourth of the underground mining fatalities occurred as the result of fall of ground. The large openings in underground stone mines present limitations in observing ground conditions because of floor-to-roof heights ranging from 20 to 60 ft or more. Generally, the status of ground conditions in under-ground stone mines is based on observation and experience obtained during mining development. Some mines use monitoring instruments to gain information on roof conditions, but this practice is typically focused and localized to address issues in a particular area or section of the mine. The Roof Fall Risk Index (RFRI) described here provides a method of systematically characterizing the risk of roof falls to enhance the safety of mine workers. Approach As in many industries, a defective product signals the potential for failure. Similarly, defective rock or strata in an underground stone mine presents a potential risk. Assessing ground conditions relative to the concentration of defects observed provides a way to index or rate these conditions and the subsequent risk. Through observations at approximately 50 underground limestone mines in the United States, strata defects were categorized to develop a quantitative method for determining the RFRI. This method is specifically geared to underground lime-stone mines because strata defects are difficult to see and limited by the experience and knowledge of the observer. Overall, 10 defect categories were deter-mined: 3 that relate to geology, 4 that result from mine development, 2 that are indicative of the roof profile, and 1 that addresses moisture or water flow (see RFRI Chart 1). The defect categories are also weighted to reflect the conditions indicative of roof or strata movement or separation (categories 4 through 8). These weights are multiplied by the assessment value to determine the total category value. The benefit of using monitoring techniques to gain information on roof conditions is also factored into the RFRI for overall assessment of an area in the mine. Each defect category is assessed with a value of 1 to 5 based on parameters as defined in each defect category, with 5 indicating the highest degree or level of defect. The assessment value of 3 is also used when information on a parameter is unknown. The parameters for the defect categories are illustrated in RFRI Chart 2 for use in determining the assessed value. How It Works The RFRI provides a means to categorize the risk for roof falls in underground stone mines. The concept of this calculation is aimed at providing an indication of the level or degree of defect relative to the area of the mine examined. The RFRI for the calculation produces a distribution where RFRI values approaching 0 represent a stable condition and those ap-proaching 100 represent an unstable condition.

Oct 1, 2006

By C. A. Herbert

In summer, when hot, moisture-laden air enters a coal mine in the region east of the Mississippi River, the moisture is likely to condense on the roof and ribs because the incoming air is cooled below its dew point upon contact with the roof, ribs, and floor of the mine passageways. When the roof and ribs become wet owing to this condensation they are said to "sweat." In many mines, as soon as this sweating begins, shale or slate roof that appears solid and strong in winter begins to cut and fall. For a long time most mining men believed (many still believe) that the roof trouble was due to this sweating. However, from observation of conditions in one mine the operators concluded that the trouble was caused by expansion and contraction of the roof due to changes of temperature. This opinion was confirmed by experiments at several mines in cooling the air as it entered the mines. Methods used in these mines for cooling the air are described in this circular. MINE A At mine A the roof gave considerable trouble in the summer, and it was observed that where a spray of water from a leaking dam kept the roof wet and at a uniform temperature no difficulty was experienced with the roof, although it had cut and fallen on either side of that point. From this fact the company officials concluded that changes of temperature in the air rather than moisture caused the trouble and that if the incoming air were cooled to approximately normal strata temperature much of the additional roof trouble experienced during the summer would be overcome.

Jan 1, 1940

By J. S. Webb

This is one of a series of papers dealing with mining methods, practice, and costs be¬ing published by the United States Bureau of Mires. In this paper a description of the mining practice in vogue at the Braden unit of the Kennecott Copper Corporation is undertaken. PRODUCTION At present (1931) the entire production of ore is being obtained from the Teniente mine. The miring method in use is an adaptation of block undercutting which has been a development of the stoping and pillar caving experience obtained at this property. Improvements in mining practice are constantly being made.

Jan 1, 1932

By Robert M. Doerr

In a process being investigated by the Bureau of Mines for recovering alumina from domestic nonbauxitic resources, calcined kaolinitic clay is leached with hydrochloric acid. Iron impurity in the clay is coleached and is removed in a solvent extraction step prior to crystallization of aluminum chloride hexahydrate, which is subsequently thermally decomposed to alumina. The FeCI3-HCl stripping liquor from the solvent extraction step is unsuitable for discharging to the environment; furthermore, economics requires recovery of the contained chloride values. In the present research, it was shown that the stripping liquor can be reacted with calcined clay to yield AlC13 in solution, plus precipitated iron oxides, residual silica, and unreacted excess clay as mixed solids. For the recovery of the AICl3 solution, the slurry could be separated or returned to the clay-HCI process stream at the solids washing step that follows primary HCI leaching of the clay. For the range 20° to 99° C, the time (t) (103 sec) required to react the waste liquor with excess clay, for essentially complete iron precipitation, depends on the absolute temperature (T) chosen, according to the expression t = e[(9.000/T) -23.5J. (1) Alumina was tried as a reagent alternative to clay but was not very effective, even under pressure and at high temperatures.

Jan 1, 1982

By A. Z. Dimitroff, A. C. Moschetti

An improvised rock- dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jun 23, 1964

By T. D. Ralston

This Bureau of Mines report presents a mathematical model for heterogeneously catalyzed chemical reactors operating under turbulent conditions. The model includes reaction kinetics on the catalyst surface as well as diffusion of the reacting components within the reactor. Three applications of the model to tube-wall methanation reactors are discussed. The first application is a computation of catalyst activity from measured reactor data. This result is then used in a reactor sizing problem and a problem of reactor simulation with recycle. In addition to the reactor model, a novel approach to solving the recycled reactor problem is given.

Jan 1, 1974

By John Durkin, Harry Dobroski

This paper presents a general overview of the Bureau of Mines' programs in the areas of operational and post-disaster communications. These programs encompass both hardware developments and system evaluations. Topics discussed include a new visual paging system compatible with existing pager phone lines, a means of modifying commercially avail able pager phones to permit selective paging and message leaving, a multiplexed telephone system that uses twisted shielded pair and requires no central control, medium frequency hardware developments, and a manual for mine communications. Research has continued in the area of post-disaster location and communications. This research is based on seismic and electro- magnetic techniques. Each has been extensively studied and field tested to better understand its ability to perform effectively. A brief description is given of the post-disaster program. Results are promising and provide insight into future areas of research.

By J. W. Paul

This circular is one of a series of papers4 on coal-mining methods and costs which are being prepared through the sponsorship of the U. S. Bureau of Mines for the purpose of presenting information on present mining methods and certain features which govern costs, safety, and conservation. The methods employed are influenced by natural local conditions with respect to the thickness, character, and dip of the coal bed, the nature of the roof and thickness of the overbearing strata, and the means employed for roof support and its control.

Jan 1, 1929

By P. M. Sullivan

This report describes a new application of electroamalgam metallurgy in recovering all the zinc as refined metal from galvanizers' sal skimmings. Pure zinc was recovered by electrolysis of skimmings leach liquors in amalgam cells. The following information was gained as a result of literature studies and subsequent laboratory investigations. 1. Reports in the literature indicate that pure zinc can be recovered from chloride solutions with the aid of amalgam cells. From Europe it was reported that amalgam cells could be used to recover pure zinc and chlorine from leach liquor obtained from pyrite cinders following a chloridizing roast.

Jan 1, 1956

By Kenneth Lipman

Auxiliary equipment was assembled around a purchased oscillograph to permit observation of the current and voltage characteristics of low-energy, capacitance-discharge sparks having durations of at least 10 mµ-sec. Circuit details of the assembled apparatus, performance characteristics of the complete system, and some preliminary data from representative self-initiated sparks are given in this report. INTRODUCTION One of the subjects of continuing research by the Federal Bureau of Mines Division of Explosives Technology is the ignition of explosive-gas mixtures by means of low-energy capacitance sparks. Quite early in these investigations it was recognized that understanding the gas-ignition phenomena would be facilitated by detailed information about the performance of the ignition source (spark) under the actual conditions of interest; however, the sparks of practical interest are nonrepetitive transient phenomena whose duration could reasonably be estimated to be in the time range of 1 mµsec. to 1 µsec. As such, the only feasible method of obtaining detailed information was and is oscillographic representation of the pertinent current and voltage transients. It was not until 1947 that a suitable, commercial, dual-channel oscillograph could be obtained as the basic instrument for these studies; the instrument specified in 1947 was delivered in 1950. This paper describes the auxiliary

Jan 1, 1959

Use instantaneous sampling to pinpoint dust sources and to Improve dust control on longwalls. Approach Use a dust monitor developed under a Bureau contract. How It Works Sampling can be done by either a moving or a stationary method. In the "moving' method, the dust monitor is carried by a survey engineer walking at the midpoint of the shearer Dust levels and face position (support number) are taken during all phases of the mining cycle while the shearer is cutting. These measurements can show how changes in airflow along the face, face specific; (rock partings) and cutting sequence (cutting the wedge) variables affect dust levels. In the "stationary sampling" method, the survey engineer stands with the RAM at a fixed location on the face. As the shearer approaches, the dust level and the distance to the shearer are recorded at 10-second intervals. Typically measurements start when the shearer is 20 feet from the sampling position and continue as the shearer passes the position until it is 20 feet away on the other side. Dust profiles around the machine are obtained at several fixed locations along the face only while the shearer is cutting.

Jan 1, 1982

By J. A. Herdlick

"INTRODUCTION The BeVan quartz crystal prospect in the Indian Creek mining district of Lemhi County, west-central Idaho, was examined by an engineer of the Bureau of Mines 3/ on July 9, 1943. As quartz crystals possessing peizoelectric properties were on the critical list of strategic war minerals, further exploration of the deposit was recommended. The Bureau of Mines exploration began in December 1943 and continued through January 1944. Additional trenching was completed during May and June 1944. This report presents the data obtained by this exploration.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual exploratoiy work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyses samples and makes beneficiation tests.The quartz crystals found during the exploration were examined and classified at the Bureau of Mines College Park, Md., laboratory and checked at the National Bureau of Standards, Washington, D. C.Fred BeVan, of North Fork, Idaho, and Edward F. Cenis, of the Montana Coal & Iron Company, Spoane, Wash., provided much information on the history and past production of the property."

Mar 1, 1948