Search Documents

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some diamond drilling at the Almedia deposit In an endeavor to find an additional source of supply of lead and zinc. It is reported that in 1816, lead and zinc minerals were found in the limestone quarries near the boundary line between Scott and Center townships. In an attempt to develop these minerals in paying quantities, an alit was driven for several rods into a bluff Just west of the present Almedia mine, This is believed to be the Web mine, mentioned briefly by Parker Cleaveland in 1816. In 1901 the Almedia mine was developed by an open cut and three shafts. The hoisting shaft at the time of drilling by the Bureau of Mines was sounded to a depth of 115 feet. A concentrating plant reportedly made shipments to Hamburg, Germany, for reduction. The deposit is in a somewhat slaty limestone. The ore occurs in a northeast fracture zone along the strike of the limestone and dips to the southeast. Old miners state that the ore appeared as large chunks of galena and sphalerite. In 1949, to investigate the downward extension of the oreshoot, the Bureau of Mines drilled four holes aggregating 1,126.3 feet.

Jan 1, 1950

By E. C. Perkins

This report describes a ferric chloride trap, based on formation of a low-melting sodium chloride-ferric chloride mixture of near-eutectic composition, and its use in chlorination of impure titaniferous materials. The trap is placed in the hot gas stream between the chlorination reactor and the condenser. Virtually all of the iron is removed by the trap. The condensed titanium tetrachloride is free of suspended solids and contains only a trace of iron. Four examples are given of the use of the ferric chloride trap in chlorination of impure titaniferous materials. INTRODUCTION In the Kroll process, ductile titanium metal is produced by reducing titanium tetrachloride with magnesium metal.4/ In commercial practice, titanium tetrachloride is produced by chlorinating titaniferous materials in the presence of carbon.2/ In 1957 most producers were using rutile, and virtually all plants were designed for its use. About four-fifths of the domestic consumption of rutile was imported from Australia. The Bureau of Mines, under provisions of contract DMP-116 with the General Services Administration, studied electrosmelting of domestic ilmenites and titaniferous magnetites to produce high-titanium slags with pig iron as a byproduct. Under the same contract, chlorination studies also were being made of these slags. Smelting was done at the Northwest Electrodevelopment Experiment Station, Albany, Oreg., and chlorination at the Electrometallurgical Experiment Station, Boulder City, Nev.

Jan 1, 1958

By Lloyd Williams

1. The investigation shows that the Poplar Creek and Big Mary beds contain the largest known recoverable reserves of coal in Morgan County, Tenn. The Poplar Creek bed has been the most productive. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 96 million tons, as of January 1, 1954. Of this total, 59 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By D. Harrington

Coal mines and mining-, as well as metal and nonmetallic mines and min¬ing, are not inherently unsafe, although mining people think they are and would like to have everyone else think so. It is now being demonstrated that mines can be operated with essentially as much safety as any other major industrial enterprise; but most mining people, including workers as well as officials, have been slow to realize or admit this. In the past, and with most people even at present, the idea has prevailed that it is utterly impossible to operate a mine without accidents. Although, as in all other kinds of industrial activity, it is true that some injury is likely on occasion to occur to some workers and an extraordinary accident may occur to one or more persons under exceptional conditions, mines can be operated with few if any accidents if a reasonable amount of the right kind of precautionary effort is exerted and kept in effect.

Jan 1, 1934

By Steven R. Munts

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 8,445 acres of the 20,650-acre Tunnison Mountain Wilderness Study Area in order to evaluate its identified mi nerd 1 resources. The study area is located in Lassen County, CA, about 8 miles northeast from Susanville. No mineral resources were identified in the study area based on literature, field observations, and sample results. No mines were operating in or near the study area in 1985, and no mines, prospects, or claims have been located in or within 1 mi le of the study area. The study area is underlain by Pliocene and Pleistocene volcanic units composed of basalt, andesite, rhyolite, and some pyroclastics. No metallic and only nonmetallic commodities are present in the study area. These included stone and sand and gravel. Although substantial volumes of basalt and andesite (stone) occur within the study area, no identified resources of these commodities were delineated. Sand and gravel is not economic because of small occurrence size and lack of local markets.

Jan 1, 1987

Develop computer software that can aid in improving the visibility and illumination in underground mines by providing quick analysis of existing equipment and conditions and the effects of potential modifications. Background Poor visibility and illumination are common problems in underground mining. Mining equipment often restricts operators' fields of vision. Also, fighting systems are often positioned where they cause excessive glare, which restricts the visibility around the machines even further. To help address these problems, the U.S. Bureau of Mines (USBM) has developed a PC-based software package to analyze certain human engineering aspects (ergonomics) of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines. Approach The Crewstation Analysis Programs (CAP) package includes assessments of visibility, illumination, and glare in the surrounding work area. The advantage of using computers for these types of analyses is that numerous design iterations can be tested quickly and efficiently to determine the effects of changes on visibility. This cuts down the need for expensive testing using physical mockups. Another advantage is that design ideas can be tested in situations where testing would not normally be possible. For instance, the effects of modifications to a lighting system or canopy design could be tested while the machine remained in service.

Jan 1, 1993

By Connie S. Musulin

Radon concentrations in shallow uranium mines such as the Bureau of Mines experimental research mine are affected by barometric pressure changes. The radon concentrations show a significant correlation with absolute pressure; but over a period of days, a steady rise or fall in barometric pressure will result in noncorrelation of data. Fan shutdowns also affect radon concentrations, and an equation was derived to determine the time required for the radon concentration to return to normal after a fan shutdown, whether the ventilation is blowing or exhausting.

Jan 1, 1982

By Michael J. Pazuchanics

This report documents the current status of the U.S. Bureau of Mines ongoing investigation of the use of adaptive signal discrimination (ASD) systems to distinguish between cutting coal and cutting rock. Cutting-tool forces and vibrations were measured in the laboratory using both conical bits and roller cutters in a linear-cutting apparatus for several material samples and two cutting directions. A number of ASD systems consisting of one or more signal classifiers were trained and tested to study how data window size, type of signal feature, and combining (polling) of classifier results influence system performance. The results show that ASD system recognition rates can be improved by increasing data window size, removing air-cutting portions from the signal data, overlapping data windows, and combining (fusing) information at various levels of ASD system operation.

Jan 1, 2010

By Will H. Coghill

Titanium is a well-known component of bauxite ores, sometimes occurring in sufficient quantity to mace its recovery worth considering. This question has been raised by some of the companies lixiviating bauxite ores. At the East St. Louis plant of the Aluminum Ore Co., a subsidiary of the Aluminum Co. of America, the waste sludge discharged daily contains over 75,000 pounds of Ti02. The sludge is all through 20-mesh, and a large proportion is slime. A supple of the waste was deslimed so that a gravity-concentration test of the "sand" could be made. The Aluminum Ore Co. cooperated in the work and made the chemical determinations In order to anticipate the results of table concentration a series of specific gravity fractions (float-and-sink) was made with heavy liquids. Acetylene tetrabromide was used for a density of 2.95, methylene iodide for 3.33, and thallium formate for 3.78, and the double salt of thallium formate-malonate made the separation at slimed sample appears in Table 1.

Jan 1, 1928

By Philip A. Holland

The Bureau of Mines has developed a method for determining helium in water for use in sampling and analyzing surface and subsurface waters for geochemical survey work. The accuracy of the analytical method is within ±10 percent for samples containing above 20 x 10-8 cm3 He (STP)/cm3 H20. The minimum detectable helium-in-water concentration is calculated to be 2 x 10-8 cm3 He (STP)/cm3 water. Water samples are collected in 500-cm3 stainless steel cylinders. The dissolved gases are extracted into a cylinder of equal volume containing a known quantity of neon. The resulting gas mixture is subsequently analyzed for helium and neon-21 by mass spectrometry. The volume of helium in the sample is calculated from the mass spectrometric determination of the helium-to-neon-21 ratio, the known quantity of neon used, and the extraction efficiency of helium.

Jan 1, 1981

By Leonard Obert

Subsidence to surface occurs in a large proportion of underground mines. Preliminary to any indication of subsidence on the surface, there is usually a breaking up and sloughing of the cover into the mine opening which, in a period of time ranging from minutes to many years, progresses to the surface, This process is referred to as subsurface subsidence. In many mining operations, information regarding the process of subsurface subsidence is important, For example, if there are buildings or other improvements on the surface, or if the direction of the subsurface subsidence might threaten other underground workings--such as shafts--or if the subsidence might be progressing in a direction which would fall outside the anticipated subsidence limits, the problem could assume special significance.

Jan 1, 1961

By M. A. Mahtab

This report describes the procedures used by the Bureau of Mines for obtaining attitudes of joints surveyed with a borescope in inclined boreholes. An algorithm for computing the dips and azimuths of the observed joints is presented. The algorithm is used to solve an example problem. A computer program based on the algorithm is listed. It is hoped that the procedures described here will be useful in treating large quantities of data obtained from comprehensive borehole surveys.

Jan 1, 1973

By Marvin L. Whisman

This report describes the preparation of tritium-labeled organic compounds to be used by the Federal Bureau of Mines in studying the role of certain gasoline constituents in gum-forming mechanisms. The gasoline constituents that have been investigated boil within a range of approximately 90 to 230° C. and can be classified as paraffins. naphthenes, olefins, diolefins, monocyclic aromatics, polycyclic aromatics, and organic sulfur, nitrogen,: and oxygen compounds. The technique of Wilzbach has been applied to more than 50 samples. Purification techniques have been developed that accomplish rapid and effective purification as well as removal of labile tritium in a one-step operation. Data are presented to show the rate of exchange between tritium and hydrogen that can be expected for a variety of compounds common to a full-boiling-range gasoline. These values should be useful to other investigators using tracer programs involving tritium labeled compounds.

Jan 1, 1961

Provide an improved, rugged, reliable, cost-effective automatic fire protection for mine haulage trucks. Approach Systems that automatically sense and extinguish fires on haulage trucks were designed, built, and in-mine tested. How It Works Temperature sensors mounted above the engine of the truck detect the heat from a fire while it is still small and controllable. A cab-mounted control panel warns the operator of the fire emergency and then automatically triggers the discharge of 60 pounds of multipurpose dry chemical extinguishing agent (from storage tanks through hoses and nozzles) into the engine compartment. If desired, the control panel can be field-adjusted by changing one resistor to delay the discharge for up to 60 seconds to allow time for the operator to stop the truck and shut down the engine. The system can be assembled with either pressurized storage tanks, or a combination of non-pressurized storage tanks plus separate pressure cartridges. This pressure source option is one of the improvements of this system over the earlier systems described in Technology News No. 11. Other improvements are a simplified control circuit and an improved sensor.

Jan 1, 1980

"Introduction.The Bureau of Mines has taken up the problem of determining a method or methods whereby underground compensation insurance rates for metal-mining companies can be equalized in proportion to the underground hazards involved. This study has been started by the writer with the assistance of Mr. I. M. Wolfin* as consultant.The present paper briefly reviews the origin of accident compensation, gives a digest of State compensation laws, and describes types of insurance carriers. This will be followed by study of the basis of premium rate, risk differentials, and cost of compensation insurance to mine operators. These data will be supplemented by an analysis of the accident hazards in different mining methods and practices, and the severity and frequency of accidents classified by time lost and period of exposure to hazard, for different States, mining methods, occupations and nationalities. Attention will be given to standardized preventives for underground accidents in metal mines, and, finally, the classification of underground metal-mining hazard for workmen's compensation insurance premium rating."

Mar 1, 1924

By L. C. George

The Bureau of Mines measured the vapor pressures of selected mixtures in the binary systems CdCl2 ?SnCl2, CdCl2 -ZnC12, PbCl2 ?SnCl2, and PbCl2 -ZnCl2 by the static pressure method. These data were evaluated by the second-law (sigma-plot) method. Equations expressing the vapor pressures and the heats and free energies of vaporization as functions of temperature are given.

Jan 1, 1969

By Jeffrey M. Listak

This U.S. Bureau of Mines report describes the implications of in-mine ground control on the automated or remotely controlled operation of longwall mining equipment, Perhaps the greatest challenge to longwall automation researchers is the development of systems that will continuously function in the complex and unpredictable underground environment. The high degree of environmental variability, together with conditions brought about by the extraction process, makes complete automation of longwall mining a difficult task. The intellectual thought processes and split-second decision making required to avert disasters are lost when workers are removed from the face. As many mine operators can attest, minor problems, left unresolved, can eventually accumulate and lead to catastrophic consequences. The automation process will have to assess and manage various routine problems that are otherwise resolved through worker observation and experience.

Jan 1, 1990

By H. D. Jacobs

The Bureau of Mines developed a concentration method to upgrade and utilize marginal natural or direct-shipping iron ores and fine-grained lean iron ores. Presently these ores receive little beneficiation and accordingly have low iron-silica (Fe-Si02) ratios. Ore samples were roasted with equal weights of solid reductant at 1,100° C for 1 hour to metallize the iron and for an additional hour at 1,200° C to promote grain growth. Concentration was effected by crushing and screening techniques and/or wet magnetic separation. Sized concentrates (minus 4 plus 35 mesh) derived from crushing-screening processes contained from 80 to 85 percent iron that was 90 percent metallized. Iron-silica ratios as high as 12:1 and iron recoveries from 75 to 94 percent were obtained. The sized concentrates were judged suitable for use as blast furnace feed. Minus 200-mesh metallized concentrates derived from roasted minus I-inch plus 8-mesh ore fractions and magnetically concentrated contained 90 percent Fe and 4 percent or less Si02, chemically qualifying them as feed for electric furnaces. Roasting minus 8-mesh ore with hydrogen, then magnetically concentrating it, produced iron concentrates containing 57 percent to 67 percent Fe and 3.6 percent to 8.4 percent Si02. The concentrates having Fe-Si02 ratios ranging from 8:1 to 12:1 were considered adequate for use as blast furnace feed. Overall iron recoveries for the 12 ores tested ranged from 56 percent to 94 percent with an average iron recovery of 86 percent.

Jan 1, 1969

By Ivette E. Torres

The final 26 tables of this chapter, tables 24-49, extend and expand the statistical series on production that was started in the 1963 edition of the Area Reports: International volume of the Minerals Yearbook and that was subsequently updated and expanded in the 1965 and 1967-90 editions. Mainly because of the separation of the countries that formed the U.S.S.R., the column that provided a 5-year average, was deleted. The listing order of major producers, however, continued to be, as in past years, in descending order of rank in the year of review, 1992. This group of tables now includes each of the top 19 crude minerals in 1983 in terms of value of their output plus 3 others of lesser rank. These 22 crude mineral commodities accounted for more than 98 % of the estimated value of world crude mineral production in 1983. Coal production, included in the 1983 value of production table as two separated entries, is combined in one table in this chapter. World output of five key downstream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil-is included because of their significance as products.

Jan 1, 1994

By E. H. Illsley

This bibliography is the first report of a Bureau of Mines research project on thermoelectric materials. Interest in such research has increased because of recent success in the design of commercial products, including generators and refrigerators, using the principles of thermoelectricity. This success made possible by the discovery of semiconductors that have much higher [effincies] than the metals and alloys formerly studied. Thermoelectricity is a term that includes a large number of phenomena relating heat to electrical energy. However, the moat important applications arise from two effects discovered by Seebeck in 1822 and by Peltier in 1834. When pieces of two unlike materials are joined at their two ends to form a continuous circuit, both of these effects may be observed. If the two junctions are maintained at different temperatures, an electromotive force known as the Seebeck voltage is generated. If, on the other hand, a current is made to flow through the circuit, the junctions of the materials will be found to differ in temperature. This phenomenon is called the Peltier effect.

Jan 1, 1959