Search Documents

By L. S. Sundae

The Bureau of Mines conducted a series of tests to compare the cutting forces required by radial and point-attack bits when making similar cuts. Three radial and four point-attack bits were tested in two coal mines using the Bureau's in-seam tester to measure coal-cutting forces in situ. Tests were also conducted to investigate the effects of weathering and cleating. The test results show that in each case, at a specific clearance angle, the radial bits required less tangential and much less normal force than the point-attack bits. The resultant of the cutting forces for some types of cut was 50 pct less at mine 1 for radial cuts compared to cuts with the best point-attack bit, and 40 pct less at mine 2. There was some difference between three types of radial bits, but it was not as significant as the difference between each type of point-attack bit. Cutting coal perpendicular to the cleat planes required less cutting and normal force than the same type of cuts parallel to the cleat planes. Test results showed no effect due to weathering on cutting force data. Cutting parallel increased forces only because cuts were made in the rock band.

Jan 1, 1987

By Matthew J. DeMarco, Anthony T. Iannacchione

Coal bumps have presented serious mining problems in the U.S. throughout the 20th Century. Fatalities and injuries have resulted when these destructive events occur at the working face. Persistent bump problems can result in abandonment of large reserves or lead to premature mine closure. Through the years, alternative techniques such as artificial supports, extraction sequencing, destressing, pillar design changes and specific pillar retreat practices have been successfully implemented to mitigate coal mine bumps. Several techniques have evolved for room-and-pillar operations that control the way the roof rock breaks, regulating the manner in which stresses are redistributed in the mined section. Special mine layouts employed in longwall mines have also proved to be successful in safely redistributing or containing excessive loadings. However, with ever increasing production rates, greater overburdens and new mining systems, the need to evolve even more effective bump control designs will continue to challenge the U. S. coal mine industry.

Improve face ventilation in mines with large cross-sectional entries. Approach Oil shale, salt, and limestone mines typically have large entries. Providing adequate airflow to the working faces of such mines for worker comfort, health, and safety is a substantial ventilation problem. If diesel equipment is used at the face or if a methane hazard exists in the mine, the problem becomes even more complex. To address this problem, a study was conducted under a joint contract between the Oil Shale Committee of the Colorado Mining Association and the Bureau of Mines. The study evaluated two face-ventilation concepts for large-entry mines. Improving Ventilation Two face-ventilation systems were selected for testing of an oil-shale mine, based on results of a cost/benefit analysis. The systems were a free-standing jet fan and a ducted fan operating in the blowing mode. The jet fan was spotted on the intake side in the mouth of the entry being advanced with final positioning, in or out, deter-mined by minimum recirculation. The ducted fan was also positioned in the mouth of the entry being advanced, with its tubing terminating 75 feet from the working face. The mine face entry was a dead heading 55 feet wide, 30 feet high, and 320 feet long. Sulfur hexafluoride (SF.) tracer gas was used to measure the performance of the two systems in diluting mine face pollutants including after-gases from blasting, hot diesel emissions, methane roof layers, and methane emitted from muckpiles.

Jan 1, 1987

By Douglas Talley

This report describes a 4-inch diameter borehole probe which contains a low light level TV camera, magnetic compass, light illumination source, bottom/water detector sensor and a pointing angle sensor. The camera viewing angle is at a right angle to the probe's body. All data from the sensor is multiplexed into the closed circuit camera video for transmission on a single 50 ohm coaxial cable to a surface control unit. Likewise control of the probe's power, zoom lens, focus, panning and aperture is accomplished via a down-link multiplexed on the same cable.

Jan 9, 1984

By R. Hogg, E. Kaya

"The presence of agglomerated particles in airborne dust in coal mines has been confirmed by SEM examination of static samples collected on substrates. In addition, the effect of agglomerated particles on the performance of cascade impactors and cyclone-type personal samplers has been studied. Simple procedures have been developed for evaluating the extent of agglomeration in air-borne dust by comparing the observed size-selectivity of the sampling devices with that expected under idealized conditions. Applications of these techniques in the laboratory and in underground mines are discussed.INTRODUCTIONAirborne dust is invariably present in mine atmospheres. Particle size is a primary factor in determining the behavior of the dust, its effects on miners' health and the effectiveness of dust control measures. Obviously, agglomeration of the dust particles can have important effects on: ""natural"" dust removal processes such as settling• the use of water sprays etc., for dust control• pulmonary deposition characteristicsIn addition, the presence of agglomerates could influence the effective toxicity of the dust. For example, ultrafine particles are often thought to be relatively unimportant in the development of respiratory ailments because of their low deposition efficiency. However, the latter could be substantially increased if such particles were present in larger agglomerates. It is by no means obvious that there should be significant agglomeration of the airborne dust in a mine atmosphere. In fact, calculations based on the classical coagulation theories indicate that, at the kinds of dust concentrations that exist even in what would be regarded as “very dusty"" atmospheres, the coagulation half-time* .should be of the order of weeks or even months. On this basis, agglomeration would be expected to be essentially negligible. On the other hand, laboratory experiments (Polat et al., 1991) have revealed very extensive agglomeration in the airborne dust released during the crushing of individual coal and mineral particles. It is postulated that such agglomeration occurs immediately at the point of dust generation. In other words, many of the fine fragments produced on fracture are never completely separated from their neighbors."

Mar 1, 1992

By Donald R. Irving

THIS CHAPTER is new to the Minerals Yearbook and will appear regularly hereafter. Its purpose is to present statistics that reflect technologic trends in the minerals and metals industries (except fuels). Much useful information has been collected annually through the Bureau of Mines mineral commodity and employment and injuries canvasses. However, these data must be supplemented by further data to permit evaluation of the type, direction, and rate of technologic change, which are vitally important in long-term mineral planning. In addition to, and fully as important as, expanding the available data is the need to ascertain that the various items collected are obtained from identical reporting units, to enable direct comparisons to be made.

Jan 1, 1960

By Clyde L. Brown

Recent developments in portable communication equipment for use in emergency recovery work following mine fires and explosions have wade possible a convenient and dependable means of directing rescue teams working under hazardous conditions. INTRODUCTION Mine rescue and recovery operations following; fires and explosions are frequently conducted under adverse conditions that require the use of oxygen breathing apparatus by members of a 5- or 6-man team. Conventional apparatus used for this purpose for many years was equipped with an oxygen supply adequate for at least 2 hours. The design of the apparatus is such that the nose passages are closed with a clamp, and breathing is accomplished through a mouthpiece connected to the apparatus by tubes and arranged to prevent inhaling air or gases from outside sources. The use of the mouthpiece has presented difficulties in the development of telephone communication because of the wearer's inability to speak while wearing the mouthpiece. The method of conducting operations of rescue teams requires a person to direct operations at a fresh-air base as close to the rescue team as possible. At least one standby rescue team and 2 or 3 other persons assigned to various tasks are stationed at the fresh-air base. An efficient and reliable means of communication between the director of operations and the rescue team is necessary for reasonably safe and efficient work in hazardous areas.

Jan 1, 1957

By Willard J. Tesch

The borehole surveying system described is used to measure ground movement over and near operating mines. The magnitude of any movement is con-trolled by the ground conditions, the mining method, and the mine progress. By correlating these factors with the measured movement, equations can be determined for predicting the effect of mine progress on the surrounding ground. These equations can also be used to predict the effect of mining a similar deposit with similar ground conditions. The borehole surveying system is used in cased boreholes to measure the inclination of the hole in two perpendicular planes. Grooved casing with an inside diameter of 3 inches is grouted in the hole. Two probes are used to obtain the data necessary to calculate the hole position versus depth. One of the probes contains a gyroscope, and the other contains a biaxial force-balance [s]ervoaccelerometer. Readings from the transducers in the probe are punched on paper tape by an automatic data acquisition system as the probe is pulled up the hole at 30 feet per minute by an electric winch. Readings from the inclinometer probe containing the accelerometer are used as input data to an on-line programmable calculator as they are punched on tape. The calculator computes preliminary results of the survey being made. The paper tapes obtained during the survey runs are later used as input to a computer that computes the offsets of the drill hole versus depth in true north-south and east-west planes. These offsets are printed for each foot of depth. Changes in these offsets between the first survey and subsequent surveys are a measure of the horizontal ground movement between the surveys.

Jan 1, 1976

By W. W. Agey

Past investigations on waterborne impurities in the flotation process have been concerned primarily with the treatment of specific ores with particular local waters. Although some anions and cations present in water are known to react with flotation reagents, a definitive study has not been made on the effect of such common ions upon the flotation process. This report describes the fundamental research undertaken to define and measure the adverse and/or beneficial effects of different concentrations and combinations of several common anions and cations when oleic acid is used to froth-float limestone from a pulp of quartz and limestone. Research on the effect of waterborne impurities upon the flotation process was composed of two equally important phases. The first phase comprised development of a procedure for floating limestone from quartz that would give the same results in test after test. Some difficulty was encountered, but once such a procedure was developed, the second phase, comprising study and measurement of the effect of various ions c on to natural water upon the flotation of limestone, was quickly completed.

Jan 1, 1963

A symposium on the health hazards of respirable dust in the mining and milling of talc was held on May 8, 1973, in Washington, D.C. The results of medical effects on both human and animal subjects were presented. Methods for identification and classification of talc minerals were also presented. Analytical techniques discussed included X-ray diffraction, scanning electron microscope observation, electron probe, and optical microscopy.

Jan 1, 1974

By McHenry Mosier

The Anson Bette manganese mine, with two prominent manganese-bearing outcrops in schist, has attracted considerable attention for its variety of manganese minerals and its possibilities as a potential source of manganese. Little mining was done prior to 1925, when the present owner acquired the property, and operations since that date have been intermittent. Mine workings are open cuts with a maximum depth of 35 feet. The two outcropping ore deposits are irregular, pipelike bodies about 500 feet apart. As nothing was known of the grade or extent of mineralization in depth, four holes totaling 1,072.5 feet of bore Were diamond-drilled by the Bureau of Mines in the summer of 1943, with the results shown in figures 3 to 6. In.1945 a geophysical survey was run to map the magnetic anomalies in the manganese-bearing belt as a means of determining the locations of manganese deposits. Positive correlation of magnetite and manganese ore was not obtained.

Jan 1, 1949

By Dipak C. Talapatra

This report describes the development of guidelines for design, inspection and maintenance of automatic couplers. In order to devise the guidelines, performance requirements for automatic couplers were carefully established. This was done through a comprehensive survey of coupler manufacturers and extensive observation of automatic couplers in service in a broad spectrum of mines. The capability of the couplers to withstand the demands of the mining environment in terms of strength characteristics, gathering range, curve negotiability, and other factors were all carefully evaluated. An analysis of coupler related accidents for the years 1972-1976 was carried out to provide information on the safety and reliability of existing automatic couplers. This formed an important input to the development of the guidelines. It is expected that these guidelines will be useful to coupler manufacturers for establishing designs for improved automatic couplers, and to mine operators for maintaining their couplers in a safe and good operating condition throughout their expected lifetime. This report is in two volumes: Volume 1 Technical Report Volume 2 Design, Inspection, and Maintenance Manual

Jan 1, 1977

By P. E. King

The U.S. Bureau of Mines is conducting an ongoing research project to better understand the phenomena involved within electric arcs utilized in electric furnace steelmaking. With a better understanding of the physical and electrical characteristics involved, dynamic or predictive control of electric arc furnaces may be possible. A mathematical model is presented, but not solved, and the system of coupled equations is analyzed. Characteristic parameters are used to determine relative importance. In this manner, significant quantities are dermed. The parameters found to contribute little to the system of equations of motion are ignored. A resultant simplified system is identified, and directions for further study are indicated toward control of electric arc furnaces.

Jan 1, 1990

To develop a system which will effectively detect and extinguish fires in underground fueling areas while also providing a warning for nearby miners. Approach A system involving optical fire sensors. automatically-released dry chemical and aqueous film-forming fluid (AFFF) fire suppressants, and automatic alarms was designed from off-the-shelf, state-of-the-art components, and was in-mine tested at two mines in the two typical underground fueling area situations: fuel transfer areas and fuel storage areas. How It Works As mines become more mechanized, the number of fire hazards increases since fueling areas are more abundant. Fire hazards are especially serious in deep mines, since escape time is longer. To help solve this growing problem, the Bureau of Mines, in cooperation with the Mine Safety and Health Administration (MSHA) and the National Fire Protection Association (NFPA), has developed and in-mine tested a cost-effective fueling area fire protection system. The system was designed to be rugged enough for reliable, long-term use, yet to utilize state-of-the-art, off-the-shelf components to maintain cost-effectiveness. The system consists of cross-zoned, ultraviolet flame sensors used for quick response to fire, and a dual-agent fire suppression subsystem. A dry chemical is used for fast fire -knockdown," and AFFF (or "light water") is used for long-term, fire-securing capability. The basic components of the system are shown in the schematic illustration.

Jan 1, 1982

By David C. Oyler, Gregory Hasenfus, Gregory M. Molinda

Few studies have specifically measured and documented the large-scale loading behavior and durability of ventilation stoppings to mining induced movements, particularly from longwalls. Ventilation stoppings are more commonly the concern of ventilation engineers, and ventilation stopping response to ground movement has only been documented in an incidental manner. This paper presents the investigations of underground measurements that have been conducted to determine the loading response of stoppings constructed from lightweight aggregate concrete masonry units (CMU). These investigations have produced some interesting results that may prove beneficial, not only for developing and assessing alternative stopping construction techniques, but also for designing and selecting standard construction methods for use in varying mining conditions. For instance, the interface friction that results from wedging a CMU stopping during construction plays a substantial role in its ability to resist both lateral and vertical loads. Although they are not intended for ground support, the study showed that block stoppings can resist vertical loads of at least 2,700 to 3,000 kN. Asymmetric loading of a stopping may result in localized failure of blocks within a stopping, which, depending on the severity, can be a precursor of impending stopping failure. In addition to measurement results and implications, the paper will also present details of field measurement methods used to assess stopping response. Stopping stiffness and material strength characteristics will also be presented.

Reduce the dust exposure to the operator of a longwall shearer with a novel foam spray system. Approach Discharge foam through the nozzles of a shearer drum so that foam and coal are better mixed. How It Works Bureau of Mines research showed that two very important principles for successful application of foam are: (1) moisture distribution and (2) degree of mixing. Foam can distribute a given quantity of moisture much more evenly over a large surface area. Successful Bureau tests of foam for dust control always involve a high degree of mixing between the foam and the material, Mixing, permits a greater distribution of foam throughout the mined product. The most suitable location of foam application would be at the point where the dust is generated, before the dust becomes airborne. Foam nozzles located in the cutter drum (pick face foaming or ejecting foam through scroll sprays) will suppress dust close to its source.

Jan 1, 1989

By Frank E. Cash

Since ventilation adequate in quantity as well as quality is of paramount importance to the health and safety of men working underground in coal mines, mining officials, employees, and State inspection departments should give it the closest possible attention. MINING LAW OF ALABAMA The law governing, and regulating the operation of coal mines in Alabama was enacted in 1911 and amended or revised in 1923, 1925, 1930, and 1935. The original law and subsequent revisions were progressive steps in safeguarding the health and safety of underground employees.

Jan 1, 1939

"The U.S. Bureau of Mines established on August 15, 1983, The Generic Mineral Technology Center for Respirable Dust (Dust Center) within the Mining and Mineral Resource Research Institutes (MRIs) at The Pennsylvania State University and West Virginia University, and in association with participating MRIs at Massachusetts Institute of Technology and the University of Minnesota. In 1986, Michigan Technological University (MTU) was awarded a grant through the Dust Center. The center's research program has been developed with recognition of the stated objective of the Federal Mine Safety and Health law, which is ""... (to) permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis of any other occupation-related diseases..."" The Dust Center's program is designed to foster an accelerated attack through fundamental research on problems confronting the control of respirable dust in mines. The interactions of the universities and the research program components in the characterization of coal seams, respirable dust particles and the workers lungs are depicted in the logo of the Dust Center.The primary goal of the Dust Center is to reduce the incidence and severity of respirable dust disease through advancing fundamental understanding of all aspects of respirable dust associated with mining and milling, and the interaction of dust and lungs. The Dust Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the fundamental dust-lung interaction processes that lead to mine worker disability. The work concentrates on: (1) control of dust generation; (2) dilution, dispersion and collection of dust in mine airways; (3) characterization of dust particles; (4) interaction of dust and lungs; and (5) the relationship of the mine environment, geology, and seam characteristics to dust generation and mobility. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines, and to other dusts such as those generated by diesel equipment. Achieving the Dust Center's goals also involves the training of engineers and scientists, graduate students, and undergraduate students through their respective institutions, and technology transfer to industry. The distribution of personnel in the various universities are presented in Table 1. A directory of Dust Center principal investigators is presented in Appendix 1. A summary of degrees granted and mineral sector employment is presented in Table 2. The subjects of theses developed under the various research projects are presented separately in Volume 7. The center research is fully compatible and complementary with the existing and ongoing U.S. Bureau of Mines activities (see Volume 2). Additionally, the expertise and facilities of the NIOSH--Division of Respirable Disease studies are available as a result of the existing relationship between NIOSH and West Virginia University. Figure 1, Respirable Dust Center Projects and Activities, presents the various projects in the five major areas of investigation and the scope of characterized dust samples, the suite of tests, the sampling and dust generation methods, and the size, chemical and mineralogical analysis performed in the center. Table 3 presents a summary distribution of the 95 publications and presentations that have emanated from the center. In addition there are more than thirty presentations made at each annual Dust Center review meeting. The titles, authors and location of presentation for publications supported by the Dust Center are presented in separate publication volumes for 1984 (Volume 3), 1985 (Volume 4), 1986 (Volume 5) and 1987 (Volume 6)."

Jan 1, 1988

By Raymond B. Ladoo

The uses of talc are many but are not, in general well known or fully developed within the last decade several companies have realized the possibilities of greatly increased use and have intelligently proceeded to develop some of the fields which seemed most promising. This has had a tendency to lift talc from the obscurity in which it had existed for years, but the work is only started and much remains to be done. Considerably more attention has been paid to the technology and utilization of talc in Germany and Austria than in this country, despite the fact that the United States produces 65 of the world's talc and Germany and Austria combined but 5.4%. In the "Bericht,uber die tatigkeit des verbends der talcum-interessenten in Oesterreich-Ungarn" (Proceedings of the Austro-Hungarian Talc Association), for the years 1912 and 1913, many notes upon new uses appeared, together with suggestions as to further development of old uses. Aside from a few notes on the use of tar in paper, little has been published in the English language upon this subject. By recent action of the Talc and Soapstone Producers Association (U.S.A.) funds for research into the properties and uses of talc have been made Available and it is hoped that markets will be materially broadened a a result of this work.

May 1, 1920

By Robert Goldstein

A computer program for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. To provide a data base for these calculations, eleven 3-D machine models were prepared and the outputs of three luminaire types were measured. Calculations were done for thirty different configurations.

Jan 1, 1977