Search Documents

By N. Greninger

The Bureau of Mines conducted a laboratory study of the measurement of the water and rock dust (RD) contents of synthetic mine-type coal dust (CD) mixtures using a commercial unit for measuring water content and several prototype radiometric units for measuring the RD content. The RD content ranged from 50 to 100 wt pct and the added water (AW) ranged from 0 to 15 wt pct. The total water (TW) content (intrinsic (IW) and AW) of a small dust sample could be readily measured automatically by essentially untrained personnel using a commercial unit. The RD content of a sample containing only IW could readily be measured by moderately trained personnel using several radiometric units. With gamma-ray devices, about 300 g of sample is needed. With the improved beta-ray device, about 25 g of sample is needed. With dry mine dust samples, the estimated RD error range for gamma-ray devices is 0.8 to 2.3 pct and 0.5 to 1.0 pct for beta-ray devices. However, the radiometric measurement of RD content was questionable if the dust mixture also contained AW or if it was uncertain whether the dust mixture contained AW.

Jan 1, 1988

By R. W. Smith

The Bureau of Mines is engaged in systematic evaluation of the thermodynamic properties of combustion gases. These studies are designed to provide basic thermodynamic information of high accuracy that will facilitate the theoretical study of flame and combustion phenomena. This report is the second of a series3/ presenting results of the study for particular fuel-oxidant sys tans. These calculations had as their objective evaluation of the constant pressure flame temperatures of methane-air and propane-air flames at atmospheric pressure as functions of the mixture ratio and inlet temperature of the fuel-air stream.

Jan 1, 1953

By Foster Fraas

This Bureau of Mines report describes a method for separating minerals at magnetic susceptibilities within the diamagnetic susceptibility range. The maximum feed rate varies directly with the square root of the lower limit of permissible susceptibility, while the lower limit of permissible susceptibility varies inversely as the square of the magnetic field strength. Minerals may be separated at particle sizes smaller than possible on conventional dry-type magnetic separators.

Jan 1, 1969

Protect rescue workers fighting fires or mine personnel temporarily working in hot environments from heat stress. Approach A specially designed ice-cooled vest is worn while working in hot environments where cooling the mine air is not possible. How It Works The vest holds a total of 44 individual ice cells in packets that are firmly held near the wearer's skin. These ice cells remove heat from the wearer, reducing heat stress and increasing comfort. The locations of the ice cells and packets are shown in the diagram. The vest is constructed in three layers with the outer layer being aluminzed fiberglass cloth. Its aluminized surface reflects radiated heat, and its fiberglass cloth provides fire resistance and strength.

Jan 1, 1979

"As stated earlier the primary goal of the Generic Mineral Technology Center for Respirable Dust is to reduce the incidence and severity of respirable dust disease through advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. While initial work was directed to coal dust the charge to the dust center has been expanded to include diesel particulates and asbestosis, the latter of deep concern not just to workers in the mineral sector of the economy but also to the general populace.A major facet of Dust Center research has been the analysis and documentation of comprehensive research protocol and procedures that are appropriate state-of-the-art in the various areas of respirable dust. In addition to definition of standardized research protocols and procedures which would be utilized by center personnel for uniformity and reproducability there is a considerable need for utilizing standardized respirable dusts in experiments with consistent, reproducible characteristics which simulate those of actual mine dust. This respirable dust needs to be available in large quantities for a wide variety of research uses that include animal and medical experiments. The dust must be free of the lubricating oils and grinding wheel contaminants that are frequently encountered in laboratory generated dusts.The holistic approach to establishing standardized protocols and procedures applicable to the five major research areas of the center is presented in Figure 5.In one hypothesis, range in coal volatility is considered to be a major causal factor in the incidence and severity of pneumoconiosis. Therefore a suite of characterized standard respirable dust samples have been prepared for researchers from coals representing the western (high volitile A bituminous), central (medium volatile bituminous) and eastern (anthracite) mining areas of Pennsylvania. Quartz, limestone (rockdust) and kaolin clay samples, representing important mineral constituents of coal dust have also been prepared.A suite of medical investigations have been developed utilizing small and medium size animals as well as non-human primates in a variety of dust/lung interaction projects which will be discussed in the next section. A number of respirable dust sampling and dust generation methods have been investigated and selected techniques utilized for both in-mine and in-laboratory research investigations. These will also be discussed in more detail later. A wide range of respirable dust size, chemical and mineralogical analyses have been investigated, standardized and documented for use in various research investigations.This interaction and documentation of various respirable dust sample procedures, animal and medical tests, sampling and dust generation methods, plus size, chemical and minerological analysis applied in the five major areas of research investigation have served to create a very favorable synergism and rapid technology transfer in the respirable dust center."

Jan 1, 1988

To develop a cost-effective tool for improving the performance of rock drilling systems used in detecting and delineating underground mine voids and for coal exploration. Approach To investigate admixtures of polyethylene oxide (PEO) at zero surface charge concentrations as drilling fluid additives to enhance penetration rates and extend bit life in rock drilling systems. Background Bureau researchers have investigated the use of chemical additives to enhance drilling performance and found that the most efficient drilling occurred when the drilling fluid was able to maintain a zero surface charge (ZSC) on the surface of the rock being drilled. Laboratory drilling studies have been performed on rock types such as quart¬zite, granite, taconite, and marble. The lab tests were conducted using 5/8-inch diameter diamond-impregnated coring bits with cationic compounds as the surface charge neutralizing additives. These studies demonstrated enhanced drilling performance, however, only at the singular additive concentration that produced the ZSC condition.

Jan 1, 1991

By D. J. Bauer

The Bureau of Mines has conducted extensive studies on the recovery of alumina from kaolinitic clay by a HCI leaching-HCI sparging process. The current study reports a modification of the process, which involves a double-leaching system. The first leach of the calcined clay is made at as high a HCI acid strength as possible so that the dissolution of aluminum chloride hexahydrate (AlCI3*6H20) is suppressed, Most of the impurities, but very little aluminum, are soluble in the strong acid. After liquid-solid separation and washing, the solids are leached with recycled weak HCI, which dissolves the AICI3'6H2O. The pregnant liquor is separated from the gangue, and AICI3'6H2O is crystallized from solu-tion by injecting HCI gas. A proposed flowsheet is presented, and the effect of bleedstream size on AlC13'6H20 purity is discussed.

Jan 1, 1984

By C. W. Owings

"PURPOSE OF REPORTThe safety and efficacy of permissible storage—battery gathering locomotives are becoming recognized more and more in coal mines. The great mobility of this type of haulage equipment is due to the fact that no trolley wire and bonding of rails are needed; hence wherever there is track and adequate ventilation to dilute properly any dangerous gases, the storage—battery gathering locomotive may go. As coal near the outcrop or the surface is mined out, coal farther from the outcrop or deeper in the ground must be mined, and gassiness of the coal bed often increases under these conditions. The use of electrical equip¬ment capable of giving off arcs or sparks while operating near or at the coal faces constitutes a serious explosion hazard. Often, it is uneconomical or impracticable to use animal haulage, and locomotives must be employed. The operator should consider the safest and most economical unit; permissible equipment is the answer to this problem, and storage—battery locomotives are the only permissible electric haulage units.A comparison of permissible storage—battery locomotives with cable—reel locomotives of the latest enclosed ""explosion—tested"" type has been made at the Keystone No. 1 mine of the Houston Collieries Co., at Keys one, W. Va. The information and data contained in this publication were obtained by the writer during an inspection of haulage at this mine.ACKNOWLEDGMENTSThe writer is indebted to P. C. Thomas, vice president and general manager, the Koppers Coal Co., operator of the Keystone mines, who granted permission for making the study. W. A. Wilson, general superintendent, Houston Collieries Co., arranged for the investigation and for obtaining the data. C. E. Zuspan, chief electrical inspector, and J. C. Newman, division electrical inspector, accompanied the writer underground and assisted materially in obtaining information and data upon the haulage methods and performance of the locomotives. The assistance or general mine Foreman Pierman and of mine foreman White is gratefully acknowledged."

Aug 1, 1931

By William C. McLaughlin

In the deep vein mines of the Coeur d'Alene mining district, rock bursts are a potential hazard to the mine structure and underground personnel. Damage repair costs are estimated by one company to exceed $1 per ton of ore mined. The Bureau of Mines, in cooperation with the mining companies, has conducted research intermittently over the past 10 years to help reduce bursts. Onsite inspections of major rock bursts were conducted, and reports were submitted to mine management; these included the geology and geometry of the affected area. The paper discusses the development and improvement of microseismic and surface monitoring equipment. The underground microseismic network, when operated on a regular basis and the results plotted daily, is capable of detecting stress concentration in certain areas. The surface seismographs record rock bursts, blasts, earthquakes, etc., throughout the district and show approximate location, time, and relative intensity of the event.

Jan 1, 1976

Control dust generated during overburden drilling at surface coal mines using either wet suppression or dry collection systems. Approach For the wet suppression systems, a range of water flow rates was tested over a number of holes. Each hole was drilled at a specific and constant flow rate. A recording flow meter was mounted in the water line near the control system pump. For the dry collection systems, each drill was tested with the front of the shroud set at different heights above the ground. Because of the irregularity of the ground surface, all height measurements were taken at the front of the shroud. Background Wet drilling systems consist of a water tank mounted on the drill from which water is pumped into the downhole air line. The water droplets in the bail air conglomerate dust particles as they travel up the the annular space of the drilled hole, thus controlling dust as the air bails the cuttings from the hole.

Jan 1, 1987

Determine the extent to which remote-sensing techniques, primarily lineament analysis, can be used to identify geologic structures that may affect the location and migration of subsidence over abandoned underground coal mines in the Colorado Springs, CO, area. Compile data using a geographic information system (GIS) to allow efficient and reproducible comparisons and analyses. Background The basis for evaluating abandoned mine land (AML) sites with remote-sensing techniques comes from past and ongoing Bureau ground control research using remote-sensing data to identify potential hazards caused by geologic structures (faults, joints, etc.) above active underground coal mines. Research showed that lineament (linear feature) analysis of Landsat Multispectral Scanner (MSS) images could indicate locations of fractures and fracture trends that had varying, but significant, impacts on the stability of mine openings. Such geologic structures should be identifiable over abandoned mines as well. If fractures are present, even if they arc not faults, they should represent areas of potential instability over these mines and, therefore, should tend to localize subsidence when it occurs, particularly for deep and moderately deep portions of mines.

Jan 1, 1992

By Jack C. White

The Bureau of Mines, in its efforts to insure the continued viability of the domestic minerals economy, has been engaged for several years in research on the extraction of alumina from domestic, nonbauxitic resources. Hydrochloric acid leaching of kaolin is one of the more promising technologies being studied for recovering alumina for feedstock to existing aluminum smelting capacity; 93 pct of this feedstock is currently imported either as bauxite or alumina. Organics contamination of pregnant leach liquor, originating during solvent extraction for removal of iron from aluminum chloride solution formed during hydrochloric acid leaching, causes rapid deterioration of the semihard rubber lining of process equipment. These organics were removed by a skimming tank-coalescer-activated carbon adsorption system. Organic levels of less than 10 ppm from the coalescer and less than 0.5 ppm from carbon adsorption were achieved. Analytical methods employing CC14 extraction and infrared spectrophotometry were developed to determine the organic content of both the liquor and the carbon. Mass transfer zones delineated in the carbon columns provide adsorption data for the design of larger systems.

Jan 1, 1981

Develop methods to detect and repair poorly functioning dust collectors on roof bolters. Approach In conjunction with a research project to reduce silica dust in coal mines, a variety of roof bolting machines operating under different conditions were examined to find out how much these machines were contributing to the silica dust problem. Results The investigation concluded that if the bolting machines' dust collector is properly maintained, very little dust can be measured in the air, even with minimal airflow over the bolter. Poor maintenance, however, frequently results in high dust levels. Three major problem areas were found. These were: (1) filter leaks, which allowed dust to escape, (2) accumulations of dust in the collection system, and (3) low airflow at the bit due to hose, fitting, and relief valve leaks.

Jan 1, 1984

By Kyei-Sing Kwong

The U.S. Bureau of Mines investigated the synthesis of advanced ceramics (SiC+AlN, SiAlON, SiC+A1203, and Si3N4+AlN) from natural clays (kaolin, halloysite, or montmorillonite) by an intercalation and heat treatment method. This process includes the steps of refining a clay, intercalating organic chemicals into its layered structure, drying the intercalated mixture, firing the treated structure at certain temperature ranges in controlled atmospheres to form desired compounds, and grinding the loosely agglomerated structure. Focus of this research is to economically process advanced ceramic structures from abundant natural resources. The advanced ceramic phases produced in this simple treatment are homogeneously distributed at the nanostructure level, and may potentially lead to cost effective manufacturing processes. The intercalation of clay was confirmed by X-ray and BET analyses. The evolution of chemical compositions during carbonization reactions and carbothermal reduction was investigated. The characteristics of refined clays and synthesized powders were studied. Advanced ceramic composites/solid solution have been produced from intercalated clays, without the presence of other compounds.

Jan 1, 2010

By Donald P. Schlick

This report presents a representative cross section of methods success- fully used to ventilate continuous-miner places as well as various factors that should be considered when selecting auxiliary ventilating equipment. Line brattice can direct fresh air to the active face reasonably well, provided that adequate area for installation is available. Continuous mining equipment, however, often restricts clearances to such an extent that proper installation of line brattice is impossible. Consequently, in many instances face ventilation is inadequate; therefore, many methods of auxiliary ventilation for continuous-mining equipment have been developed and have been discussed in this study.

Jan 1, 1963

Provide better ventilation for mines by reducing air leakage around stoppings. Approach Most stoppings are constructed of concrete blocks and trowelled-on mortar and are not very airtight. Bureau of Mines research has shown that brushing on modified mortar containing fiberglass and/or other additives, that enhance strength and adhesion, minimizes air leakage around and through the stoppings. Airtightness is an important factor in building stoppings since an airtight stopping will provide for more efficient ventilation airflow and more cost-efficient use of the mine's ventilation system. How the New Technique Works After broken floor and rib material is removed, the stop-ping faces are covered with one or two coats of modified

Jan 1, 1982

By Brian Kenner, Peter Swanson, Todd Krahenbuhl

NIOSH has developed an automated PC-based seismic event (induced earthquake) monitoring system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network is a central feature of the system. Mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface. Seismic event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system’s design philosophy, hardware and software components, examples of installations, and a few observational results.

1.1 Bituminous-Coal and Lignite Dust. - Carboniferous material having a volatile ratio of 12 percent or more by weight and a fineness such that the material passes through a No. 20 sieve. 1.2 Active Underground Workings. - Underground places in which men are required to be or to pass through in the performance of normal mining operations for the production of coal. 1.3 Working Areas. - Underground areas where bituminous coal and lignite are mined, specifically: (a) Face. - The solid surface of the unbroken portion of the coalbed at the advancing end of the working place. (b) Face Area. - The working area inby the last open crosscut in an entry or a room, including the pillar being extracted or longwall being mined. (c) Room. - A place abutting an entry or airway where coal has been mined and extending from the entry or airway to a face. (d) Crosscut (Breakthrough). - Passageways or openings cut through a pillar to connect adjacent entries or rooms. 1.4 Entry. - Underground haulageways, travelways, and airways, except working areas as defined in section 1.3. (a) Active Entry. - An entry in which coal is being mined from a portion thereof or from connected sections. (b) Parallel Entry. - Usually an intake airway parallel to the haulageway. (c) Back Entry. - Usually a return airway parallel to the haulageway.

Jan 1, 1960

Develop technology for preparing thick corrosion-resistant coatings and electroforms of iron-chromium-nickel alloys. Approach To reduce the United States' dependence upon foreign sources for supplies of strategic and critical metals such as chromium, cobalt, and nickel, new technology must be devised to conserve these valuable commodities. One approach being investigated by the Bureau of Mines is the use of a modified-aqueous-electrodeposition method to prepare thick (-25 µm), complex alloy coatings (e.g., stainless steel composition) with properties similar to the commercial alloys. An alloy coating on a low-alloy steel or carbon steel substrate would require significantly less strategic and critical metals than those contained in an equivalent mass of the commercial alloy. Coatings applied to appropriate mandrel materials make possible the preparation of intricately-shaped alloy electroforms (near-net-shape parts). As a result, the loss of valuable metals associated with machining finished products would be minimized.

Jan 1, 1986

By Walter Kawa

In connection with its research in producing synthetic liquid fuels from coal, the Federal Bureau of Mines studied reactions of iron and iron compounds with hydrogen and hydrogen sulfide in batch autoclaves. The Bureau hoped to gain indirect evidence regarding the chemical changes that iron catalysts undergo when they are used in the hydrogenation of coal. The information obtained may be helpful in identifying the active form or forms of iron catalysts. At 450° C., with hydrogen at hundreds of atmospheres and hydrogen sulfide at 1 or 2 atmospheres, the thermodynamically stable form of iron is ferrous sulfide in the case of the metal, magnetite, ferric oxide, ferrous sulfate, ferrous oxalate, or the chlorides of iron. However, complete conversion to ferrous sulfide was not achieved at temperatures of 400° to 500° C. for kinetic reasons. Extensive sulfiding of iron, magnetite, ferric oxide, and ferrous oxalate occurred below 400° C., and some conversion of ferrous sulfate to ferrous sulfide occurred at 400° C. In the hydrogenation of coal, ferrous sulfide is the form of iron likely to be available for heterogeneous catalysis when starting with the metal, oxide, sulfate, or oxalate.

Jan 1, 1960