Search Documents

By R. V. Higgins

A numerical method is presented to calculate the pressure distribution in a petroleum reservoir that has irregular boundaries. The computer program is straightforward and requires minimal data preparation. The method can also be used to determine pressure distribution in many other types of underground reservoirs. In this method, the grid solution of the fluid-flow equations in a reservoir that has regular boundaries (previously published) was expanded to handle irregular boundaries. The computer program locates grid points at the irregular boundaries. The method of mirror images is then used to form a special stencil to determine the pressure at each of these points. Two examples are presented to demonstrate the applicability of the method for virtually any reservoir configuration.

Jan 1, 1972

By A. Matzick

In its work under the Synthetic Liquid Fuels Program the Bureau of Mines has developed on a 6-ton-a-day-pilot-plant scale a continuous, gravity-feed retort far distilling oil from oil shale. The development work covered by this report was done from January 27, 1950, to January 26, 1952, at the ail-Shale Experiment Station near Rifle, Colo. Over 300 pilot-plant tests were made during the investigation. The basic retort developed has been named the Gas-Combustion retort. In this process, part of the heat for retorting of the shale is generated by burning recycled product gas in a combustion zone within the descending shale bad in the retort. Additional heat is supplied by combustion of the carbonaceous residue remaining in the spent shale after the oil has been distilled. Air for combustion is admitted through an air distributor in the center of the bed at about the mid-point of the retort. Hot gas rising from the combustion zone heats countercurrently the descending raw shale and liberated shale oil by pyrolysis of the shale. After passing through and exchanging heat with the incoming raw shale, the oil is condensed as a fog or mist in the gas, which is withdrawn at the tip of the retort. The cool gas is then piped to an oil-recovery system where the oil is separated from the gas in centrifugal separators or other types of mechanical or electrostatic separators. The hot, spent shale below the combustion zone is cooled by heat exchange with recycle gas, which is a portion of the effluent gas from the oil-recovery system.

Jan 1, 1955

By W. S. Landers

In contrast to the large fund of information available on the carbonizing properties of Eastern U.S. coals, the experimental data available for most Western U.S. and foreign coals are meager. To supply some self-consistent data, the Bureau of Mines conducted 220 low-temperature carbonization assay tests at 500° C. in a laboratory-scale carbonization apparatus. The results are included in this report. The U.S. coals tested are from Alaska, Arizona, Colorado, Illinois, Montana, New Mexico, North Dakota, Pennsylvania, Ohio, Texas, Utah, and Wyoming. Assays were also made on coals from Canada, Ecuador, France, Greece, India, Mexico, the Philippine Islands, Thailand, and Yugoslavia. In addition, one assay of pine sawdust and one assay of a peat from Ireland are reported. Prediction equations were developed relating the yield of products of carbonization obtained at 500° C. in the assay unit to the proximate and ultimate analyses of the coals. The equations for predicting the yields of tar plus light oil, char, and gas, and the heating value of the gas, are considered good, each equation having a multiple correlation coefficient of 0.90 or higher. The equation predicting volume of gas obtained upon carbonization is considered as fair, with a multiple correlation coefficient of 0.84. A reproducibility study of the assay made on 10 replicate samples of a subbituminous coal indicated that the standard deviation of the individual products was 0.31 percent or less.

Jan 1, 1961

By N. L. Kozlinsky, B. W. Gandrud

"The Marvel mines 1 and 3 of the Roden Coal Co. are located in the Cahaba field in Bibb County, Ala., nearly southwest from Birmingham, an airline distance of roughly 30 miles. The coal of the Clark seam at this point has some coking properties, but at present it is sold exclusively as a domestic and steaming coal.This paper, which is the second of a series on the washability of Alabama coals, like its predecessor dealing with the Mary Lee seam,5 contains screen-sizing and float-and-sink tests of a representative sample of the raw slack, and slotted-screen tests showing the proportions of flaky particles in certain selected sizes; inasmuch as this coal is not used for coke manufacture, no crushing tests have been made. These data have been obtained in connection with an exhaustive study of coal preparation in Alabama, now being conducted by the United States Bureau of Mines and the University of Alabama with the cooperation of the different coal operators. As the work progresses, other papers will follow containing further data on Alabama coals and giving results obtained in preparing these coals by various methods.The only published investigative work on the Clark seam is that of Forbes,6 who gives a number of sections of this seam in Marvel No. 3 mine with proximate and ultimate analyses of face samples taken in the mine and also some analyses of delivered coal.The available information on this coal indicated that the preparation problem was one of ash reduction. In order to substantiate this information a complete analysis of the 3/4 by 3/16 inch size, and sulphur determinations and ash-fusibility tests of the float-and-sink fractions have been made; these results are given in Tables 1 and 2. As these results also indicate that the preparation problem is one of ash reduction, the tests and discussion have been devoted to that subject."

Jun 1, 1930

By W. S. Anderson

The use of flexible liners for support of underground openings has been investigated by the Bureau of Mines. This report presents installation procedures and instrumentation results of a full-scale flexible liner field installation in the Burgin mine. The flexible liner is a part of the mine support system and has provided maintenance-free support for 22 months

Jan 1, 1975

By Joseph C. Zelanko, Christopher Mark

During August, two eastern Kentucky coal miners died in a roof fall during retreat mining operations. They had just finished extracting one pillar block and were moving to the next one when the intersection they were standing in collapsed. Regrettably, this was not an isolated incident. Since the end of 2000, there have been 28 ground fall fatalities in U.S. coal mines. Of these, 10 occurred during pillar recovery operations. Although pillar recovery has been associated with about one third of recent ground fall fatalities, it accounts for only about 10% of U.S. underground coal production. Statistically, a coal miner engaged in pillar recovery is several times more likely to be killed in a ground fall than a miner on an advancing section of a longwall. Pillar recovery is dangerous because it creates an inherently unstable situation. Once the pillars are extracted, the roof is expected to cave. Safe pillar recovery does not mean preventing roof collapse, it means ensuring that it only occurs after the miners have completed their work and have left the area. Fortunately, there are a number of proven techniques that can greatty reduce the hazards of pillar recovery. These include better mine planning, improved roof support, and safer work procedures. The goal of this article is to describe the most significant "risk factors" associated with pillar recovery, and prescribe control techniques that, taken together, can reduce the overall risk to miners. The conclusions are based on extensive studies conducted by the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) that have included detailed analysis of every fatal retreat mining incident since 1992 (25 incidents resulting in 30 fatalities). Risk reduction strategies for pillar recovery can be divided into three main groups: Global Stability: Prevention of section- wide pillar failure; Local Stability: Prevention of roof falls in the working area; and Work procedures and worker location: Minimizing exposure to hazardous areas.

By R. Hogg, T. H. Dumm

"The mathematical treatments used in the evaluation of particle size distribution from pipet-withdrawal centrifuge data are reviewed. An error in the published procedure for multiple-sample withdrawal systems is pointed out and a corrected formulation is presented. An alternative treatment, based on a piece-wise linearization of the size distribution is described. Computer simulations of the analytical and data evaluation procedures indicate that the errors in the original formulation are not generally serious and that the corrected and alternative procedures lead to very similar estimates. Except for some cases involving very narrow size distributions, the alternative approach appears to give slightly closer estimates of the size distribution. Comparisons based on actual experimental data are also described.1 IntroductionSedimentation methods are widely used for the determination of particle size distributions. The procedures are relatively simple to use and the results are essentially absolute, requiring no external calibration. Gravity sedimentation is typically applicable to particles in the size range of about I to 50 pm and generally involves measurement of the relative concentration of particles as a function of depth and time in a dilute suspension. Particle size is calculated using Stokes, law:"

Mar 1, 1989

By John Neil, John Bli ard

Coke breeze consists of the smaller particles of coke formed by handling coke on and after removal from the ovens. Its value as F, fuel is less than that of the larger pieces, both because the smaller pieces contain more ash and therefore have a lower calorific value, and because a greater draft is required to burn it.The tests described below show its value as a fuel when mixed with bituminous coal and burned in a hand fired boiler of a size considerably greater than that used in an ordinary house. The results of these tests, however, can be used to give a fairly good indication of the value of coke breeze when burned with bituminous coal in a domestic furnace.All who fire a domestic furnace know that for only a comparatively short part of the day, and then only on a few days, is it necessary to open fully the ash, pit door and stack damper to get the required rate of combustion in the average furnace in the average house. It will be practical, therefore, during the greater part of the heating season, to fire coke breeze with the coal and use more of the available draftsFor domestic heating the coke breeze should be stored separately, and used when the draft is sufficient to burn it in mixture with bituminous coal, at the rate required to warm the house.Purpose of tests: The tests were carried out at the request of the Chamber of Commerce of Pittsburgh, Pa., in order to determine the steaming value of coke breeze as a fuel when mired with Pittsburgh coal and fired by hand, and to see whether the mixture when burnt would give off an objectionable quantity of make.

May 1, 1921

By R. D. Leitch

The pollution of streams by acid mine drainage has become of great importance in the past few years in certain regions of the United States. Large quantities of acids are used in a discharged from other industries than mining, notably in tube, sheet, tin-plate and era hell inn works. These are usually less important then coal mines as a source of acid drainage, because of their more limited distribution throughout the States most affected by acid waters and their relatively smaller numbers. Streams are naturally alkaline and are, therefore, able to take care of rather large quantities of acid wastes, but when such enormous quantities as are often found in mining districts enter the streams, the natural alkalinity is quickly overcome. When a neutral or almost neutral condition has been reached, the further addition of a relatively slight quantity of acids will cause a great difference in the quality of the water.

Jan 1, 1926

By S. R. Wilson

[The Anniversary-Bucky pegmatite is one of the largest, dikes in the Quartz Creek district, 21 miles east of Gunnison, Colo. The major dike consists of quartz-albite pear pagmatite and graphic granite with many quartz masses as individual cores occurring within the dike. A mining operation on one of the largest core areas has exposed several mineralogic cones directly associate with the core. These zones, including the large- units of the dike, are quartz pegmatitc, quartz-perthite pegmatite, perthite pegmatite, muscovite-feldspar -quartz pegmatite, quartz-albite pegmatite, and perthite-quartz (graphic granite) pegmatite. Muscovite and beryl are found in the muscovite-feldspar-quartz zone and are the only two products that have been marketed. Other potential products are perthite, graphic granite, and possibly small quantities of columbite-tantalite, monazite, and related radioactive minerals. The Bureau of Mines drilled two diamond-drill holes during April 1950 to investigate the largest and cost promising core area. This, report describes the results of this drilling.]

Jan 1, 1953

By Robert J. Timko

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has re- searched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world, and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1986

By G. L. Oldright

In the first paper of this series (R. 1. 4333) on the cooperative work with the Eagle-Pitcher Mining & Smelting Co., changes in the nature of the sinter feed were measured by corresponding changes in the retorting temperatures necessary to distill zinc at the best rates; the firing schedules summarized such changes. In this paper, third of the series, are noted same of the changes in practice that were brought about by the need to treat more fused, glassy, and "hard" sinter, as the operators qualify it. Losses of uncondensed zinc were increased by adding zinc-bearing materials from which? the zinc was readily distillable to hard sinter requiring higher-temperatures for zinc distillation. The rates of zinc distillation were increased by grinding the fuel finer; there were few benefits and loss of dust on grinding the sinter finer, unless the fine ?coal and fine sinter were brought into contact by pelletizing, and the pellets made but little dust.

Jan 1, 1948

By G. E. McElroy

The Coeur d'Alene minim, district of Shoshone County, Idaho, has been one of the largest and most active lead-silver producing districts in the United States for the last 40 years. The mines of the district enjoy exceptional natural advantages with respect to ventilation in that the veins apex high on mountain sides and are most often developed to considerable depths, up to 2,000 feet, by adit and crosscut tunnels under conditions that develop large natural draft pressures; the increase of temperature of the rock with increase of depth from surface in at a low rate; and the average surface temperatures are low. These natural conditions have, in the main, resulted in well-ventilated mines with low temperature conditions throughout. However, where the development has been carried to considerable depths below the lowest level of surface entry, natural-draft ventilation has proved inadequate, and mechanical ventilation systems have been installed on the three largest mines of the district. Local conditions, more particularly those in dead-ended working places, have also required auxiliary ventilation by will fan-pipe units in these and other mines. A particular feature of the district is the number of exceptionally long crosscut tunnels that have been driven to provide entry to vein systems from low points adjacent to milling and transporta¬tion facilities. Three of these tunnels are approximately 2 miles long, and lengths of 3,000 to 8,000 feet are quite common.

Jan 1, 1931

By D. R. Tweeton

The U.S. Bureau of Mines, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research Organization, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in locating a brine solution simulating in situ leach solution or a high-conductivity plume of contamination. The brine was approximately 160 m below the surface. The testsite was the University's San Xavier experimental mine near Tucson, AZ. Geo- physical surveys using surface and surface-borehole, time-domain electromagnetic (TEM) induction; surface controlled-source audiofrequency magnetotellurics (CSAMT); surface-borehole, frequency- domain electromagnetic (FEM) induction; crosshole FEM; and surface magnetic field ellipticity were conducted before and during brine injection. The surface TEM data showed a broad decrease in resistivity. CSAMT measurements with the conventional orientation did not detect the brine, but measurements with another orientation indicated some decrease in resistivity. The surface-borehole and crosshole methods located a known fracture and other fracture zones inferred from borehole induction logs. Surface magnetic field ellipticity data showed a broad decrease in resistivity at depth following brine injection.

Jan 1, 2010

By J. M. Kuchta

The chemical and thermal criteria used for predicting the spontaneous combustion hazard are briefly reviewed and data are presented to characterize the gas desorptions and self-heating tendencies of 29 U.S. coals. Closed vessel desorption experiments showed that CO, CO2, and CH4 are the main gases evolved and that the CO, CO/?O2 index, and 02 absorption rate increase with decreasing rank and increasing oxygen content of the coal. In this Bureau of Mines report, the effects of temperature, moisture, and other variables are discussed together with the application of the data to the complex conditions encountered in a mining environment. An important finding is that the presence of CO alone in a mine is not necessarily an indication of a self-heating reaction of the coal. Based upon experiments conducted in an adiabatic-type calorimeter, the self-heating temperatures of lignite and subbituminous coals can be as low as 30° C, whereas the bituminous coals require a temperature of about 60° C or more. The self-heating hazard is greatest when the coals are dried and exposed to a high humidity condition, apparently as a result of the "heat-of-wetting." Generally, the hazard is greatest with the western coals of the United States.

Jan 1, 1980

By B. H. Eccleston

Experimental work is reported showing the effects of gasoline characteristics on auto emissions. Fuel volatility is shown to influence evaporative losses, with the higher losses associated with higher volatility. Fuel front-end olefin is shown to contribute significantly to reactivity of emissions. Large vehicle-to-vehicle differences were found. The study was conducted by the Bureau of Mines at its Bartlesville Energy Research Center in cooperation with the Coordinating Research Council Air Pollution Research Advisory Committee. The work was done using 15 1968-70 model autos and eight fuels were tested at ambients ranging from 20° to 95° F. Data on emissions from each vehicle-fuel-temperature combination are presented. Also included are calculated photochemical reactivity data and the distribution of hydrocarbon and nitrogen oxides during the test cycle.

Jan 1, 1972

By F. N. Kissell, C. H. Elder, C. M. McCulloch

The applicability of the "direct method" for determining the methane content of virgin coalbeds was tested. Preliminary results indicate that the direct method, when applied to exploration cores, can be successfully used to estimate coalbed gas content and also approximately predict the total gas emission from a prospective mine located in the coalbed at the exploration site.

Jan 1, 1973

By S. M. Shelton

The widespread occurrence of domestic manganese deposits and the shortage of ferromanganese-grade ore have been sources of much speculation and investigative effort for many years. The present emergency has intensified the search by the Bureau of Mines for methods of producing ferromanganese-grade concentrates4/ from low-grade ores.

Jan 1, 1941

By John Henderson

If you missed this year?s Texas State Holmes Safety Association meeting, you missed a great one. On January 23 & 24, 2009, we held the meeting that was rescheduled when Hurricane Ike threatened Corpus Christi in September 2008. Sixty-five persons from across the state attended the meeting held at the Holiday Inn Emerald Beach. The weather was 82 degrees, and the sky was clear and perfect for a safety meeting. Evaluations submitted by the attendees gave the presentations, the networking, and even the food top marks. There were eight councils represented; Big Country, Central Texas, Costal Bend, Heart of Texas, Hill Country, North Texas and North Central. Presentations included Workplace Examinations, Emergency Preparedness, Screen Safety, Contractor Responsibilities, Powered Haulage, Supervising for Safety, and Basic Inspections of Slings and Rigging. Mr. Edward Lopez, SC MSHA District Manager, gave the State of the District Address.

Jan 1, 2009

By S. M. Shelton

[The widespread occurrence of domestic manganese deposits and the shortage of ferromanganese-grade ore have been sources of much speculation and investigative effort for many years. The present emergency has intensified the search by the Bureau of Mines for methods of producing ferromanganese-grade concentrates4/ from low-grade ores.]

Jan 1, 1941