Search Documents

By R. J. Fantel

To determine the availability of phosphate rock from domestic re- sources, the Bureau of Mines evaluated the potential production of phosphate rock from the demonstrated resources of 130 mines and deposits. The evaluation included an estimation of resources, engineering methods, and capital and operating costs, and an economic analysis to determine each operation's average total cost of production over the life of the mine, including a 15-pct discounted-cash-flow rate of return on all investments. Quantified but not evaluated in this report are substantial phosphate resources at the inferred and hypothetical resource levels. The 130 mines and deposits contain 6.4 billion tons of recoverable phosphate rock product, about 20 pct from producing mines. At total production costs of under $30 per ton in January 1981 dollars, about 1.3 billion tons of phosphate rock product is potentially available, over 90 pct from producing mines. This study suggests that production from low- cost, high-grade phosphate mines now in operation will decline during the next decade, and new higher cost, Lower grade mines will have to be developed to satisfy demand into the next century, In addition to the demonstrated resources evaluated in this study, 7 billion tons of inferred-level and 24 billion tans of hypothetical- level phosphate rock are potentially recoverable, which, in part, includes material containing high amounts of magnesium, Much of this material could likely become available in the near future.

Jan 1, 1983

By E. P. Youngman

The mining law of the Belgian Congo does not cover the Province of Katanga nor the District of Kivu (in Eastern Province). Regulations of the Comité Spécial du K tanga are in force in Katanga and those of the Comité National du Kivu in Kivu. The three laws differ only in detail, and grants made by the Comité Spécial du Katanga or by the Comité National du Kivu must be approved by the Ministry of Colonies. The following résumé is designed to coordinate the three sets of regulations.

May 1, 1930

By John W. Buch

"INTRODUCTION The Ruhr coal basin is estimated to cover an area of more than 1,000 square miles. Here, the total thickness of the coal bearing formation (Carboniferous) is 10,500 feet, and drilling-hole have revealed 92 coal beds with a total thickness of 262 feet. 6/ Beds pitch from 0 to 90 degrees and about 70 percent of the wartime production came from beds that pitched less than 30 decrees. 5/For example at the Minisiter Stein mine, there are 24 minable coal beds ranging from 80 centimeters. (2 ft., 7 1/2 in.) to 250 centimeters (8 2 1/2 in.). The vertical thickness of the measures is 1,000 meters (3,200 ft.), and at this mine the deposits are covered with 150 meters (500 ft.) of surface wash. The cross section (fig, 1) at Fritz mine; Hoesch, A.G., Essen, Ruhr, is characteristic, The mines have been developed and worked to vertical depths of 2,000 to 2,500 feet by vertical shafts; main-level intervals are 500 to 700 feet apart. Haulage roads are straight, driven in rock, and centered as nearly as practical between property boundaries. Levels are sectionalized by driving crosscuts at right angles to the main haulage road on 800- to 900-foot centers. The roads are the main transportation arteries for the use of trolley or Diesel locomotives. A plan of the sixth main level (fig. 2) at the Bruchstrasse mine; Gelsenkirchener A.G., Bochum, illustrates main-level development and,sectionalizing with crosscuts. The cross section in figure 3 is that of the fourth crosscut west at the same mine."

Oct 1, 1946

By J. W. Thompson

ORE CONCENTRATION PROCESS-PATENT OIL FLOTATION PROCESS. The invention of the patent issued to Sullman, Picard & Ballot November 6, 1906 (United States Letters Patent No. 835120), is based upon the discovery of an wholly unexplained phenomenon arising from the agitation of ore pulp containing oil and air in certain proportions. This was a discovery in an art in which it was well known that the elements of oil, air, and agitation possessed certain characteristics and produced certain results. As early as 1860 a British patent first suggested the use of oil in water concentration of ores by pointing out the affinity which oils have for metallic sub- stances in preference to gangue. Subsequently many patentees employed the known affinity of oil for metal in ore concentration proc- esses by using oil in proportions varying from 2 per cent to 300 per cent of the ore and recovering the oil-coated metal particles by causing them to rise to the top or sink to the bottom of the pulp. In these processes the agitation was either gentle or thorough but never great, and though always employed to produce thorough oiling of the metal it was used in different degrees for the sole pur- pose of causing the metal particles to rise or sink. In the prior art the oil was used for its known selective affinity for metal, agitation was em- ployed to mix the oil with the metal, and air was introduced to supple- ment the buoyancy of oil in raising oil-coated metal particles to the surface. To this extent had the art of oil flotation advanced when the patentee entered it, having reached the commercial stage in only two processes, representing respectively metal-flotation and metal-sinking processes, and having reached the stage of success in none. In the line of experiments by the patentee when the proportion of oil to ore was reduced to 1.5 per cent a "float" appeared; at 1.04 per cent still more "float" appeared; at 0.32 per cent the "float" again vastly in- creased; at 0.1 per cent the "float" again vastly increased. It thus developed that in using oil at 0.1 per cent or even at 0.05 per cent of the ore and after violently agitating the pulp from 24 to 10 minutes, there arose to the surface when the pulp was brought to rest, a thick froth or foam of oil-coated air bubbles carrying oil-coated metal particles to the extent of about 90 per cent of the metal con- tent, the foam being sufficiently stable to permit removal and metal recoveries. This was a new result based upon phenomenon then unknown and still unexplained and constituted discovery and promised a change in the art of oil flotation from laboratory experi- ments and mill failures to commercial success. The patent referred to covering the points mentioned has been sustained by the District and the Circuit Courts of Appeals and by the Supreme Court. Miami Copper Co. v. Mineral Separation, 244 Federal, 752, pp. 754-757. ORE CONCENTRATION PROCESS-OIL FLOTATION-INFRINGEMENT. The Miami Copper Co. in its process of concentrating ores by the oil flotation process used three distinct processes that were either the processes included and covered by the Sullman, Picard & Ballot patent or their fair equivalent and which were clearly an infringe- ment of the patent, and the company can not escape liability for such infringement by taking an additional step, although such additional step if taken alone would not constitute an infringement of the Sullman, Picard & Ballot patent. Miami Copper Co. v. Mineral Separation, 244 Federal, 752, p. 768. ORE CONCENTRATION PROCESS-VALIDITY OF GREENWAY PATENT. The patent issued to H. Greenway, June 9, 1914 (Letters Patent No. 1999699), is valid. The process disclosed in this patent was a substantial departure from processes of the prior art. The heating of water is a matter of large moment and the use of acids is a matter of constant and considerable expense. By wholly dispensing with both by the use of a minute quantity of hydroxy compounds, the patentee has disclosed an original and novel plan which has broad- ened and made more simple the agitation process of air flotation. The novelty and inventive character of Greenway's discovery is patentable.

Jan 1, 1918

By Ivette E. Torres

The estimated value of world crude mineral production in 1992 was $1,633.3 billion in terms of current (1992) dollars, or $1,178.0 billion in terms of constant 1983 dollars. This latter figure was 4.8% above the 1992 level but was 2.4% below the record-high level of $1,207.1 billion 1983 dollars set in 1980. Table 1 provides the latest available revised time series of the estimated value of world crude mineral production both in terms of 1983 constant dollars and in terms of current dollars. The statistical base for this estimation is derived from the data on the value of production of a group of key commodities that was published in the authoritative French language mineral industry periodical, Annales des Mines, for selected years up to 1983. The aforementioned values and those presented in the table are for crude minerals only and only begin to suggest the impact that the mineral industry has on the world economy. These figures represent only the value of mineral materials as they are mined or otherwise extracted from the Earth. They do not reflect the value added to these materials through downstream processing within the facilities commonly accepted as mineral industry plants. That is, value added through beneficiation of ores, smelting, refining, and similar processing is not included in these figures. Comprehensive world data on the value added by such processing are not available; however, a conservative estimate of the total value of processed output from mineral industry plants derived wholly from primary (newly mined) materials would be on the order of about $2,800 billion constant 1983 dollars or $3,900 billion in terms of 1992 dollars.

Jan 1, 1994

By Maurice Deul, Herbert H. Fields, John H. Perry

The Bureau of Mines has been promoting health and safety in mining since its establishment in 1910. One area of research covers methane control in coalbeds; this report describes a multipurpose borehole used for both degasification and the production of commercial-quality gas. The multipurpose borehole was drilled into a barrier pillar, and seven horizontal degasification holes and one pressure point hole were drilled radially out from its perimeter. On January 28, 1974, after 505 days of degasification, a compressor was installed to the exhaust stack of the multipurpose borehole (2), and pipeline--quality gas was introduced into a commercial pipeline. As of February 4, 1975, over 171 million cubic feet of gas had been purchased by the gas company. The in situ pressure at a depth of 200 feet into the coalbed and the average gas flow and water flow from the degasification holes as they were completed and closed off were 203 psig, 1,200,000 cfd, and 6.8 gpm, respectively. Twenty-four hours after the seven holes were connected through individual pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psig. Five hundred days later, the corresponding values were 620,000 cfd, 0.15 gpm, and 10.5 psig. Daily flows have been as high as 800,000 cfd, and as low as 360,000 cfd, during the last 500 days. On February 4, 1975, after 882 days of degasification, 576 million cubic feet of gas had been removed from the Pittsburgh coalbed; apparently a much larger area of virgin coal is being degasified than is defined by the holes. This study indicates that horizontal boreholes drilled into a coalbed from the bottom of any shaft will effectively remove gas from the Pittsburgh coalbed.

Jan 1, 1975

By A. B. Hooker, L. C. IlsLey

"Field inspections and data relative to the use of rubber—sheathed trailing cables in mines show that much cable is ruined or its probable life shortened by being overheated in service.The length of cable required to make connection from a source of supply to a machine at the face workings may be 100 to 500 feet. As a rule, the cable is carried on a reel and unreeled as required; and thus in most cases some of the cable is not removed from the reel. The overheating generally occurs in that part of the cable which is left on the reel.Factors that determine the heating of trailing cables are:1. The size of the conductors in the cable.2. The maximum energy to be supplied through the cable, based upon the horsepower of the motor and the degree to which the motor is loaded.3. The voltage of the supply and the variation of the voltage at the receiving4. The time length of current flow and whether continuous or intermittent.5. The kind of current (direct or alternating).6. The amount of cable left on the reel.7. The type of cable used.8. The kind of reel used.In connection with an investigation of the general performance of rubber—sheathed trailing cables, the Bureau of Mines has made a limited study of some of these factors, including the following points:"

Jul 1, 1931

By W. A. McKinney

A sample of oxidized copper ore from a large deposit located in Pinal County, Ariz., about 50 miles northeast of Tucson, was treated by the Federal Bureau of Mines in a small-scale continuous pilot plant by a procedure which comprised acid curing complemented by water leaching and countercurrent decantation washing in a series of drag classifiers. A feed was prepared by pugging minus 1/4-in, ore with concentrated sulfuric acid and about 10 pct, of eater, followed by curing in batches for about 24 hr. The cured ore was fed continuously to a leach drum, where it was mixed with advance solution from the countercurrent washing system to dissolve the sulfated copper. The pulp was thickened and washed in four Esperanza-type classifiers, using a flocculating agent to obtain rapid settling and thickening. The leached ore pulps thickened satisfactorily in the drag classifiers when about 0.8 lb. of a polyacrylamide flocculant per ton of dry feed was used. Clear overflow liquors were obtained, and classifier rake products containing about 60 pct. solids were produced, As much as 90 lb./hr. of ore was treated in the plant, with a recovery of 60 pct. of the total copper or 80 pct, of the acid-soluble copper when 2 tons of water per ton of feed was used in washing. The acid consumption was 4.3 lb./lb. of copper recovered. On the basis of the maximum feed rate employed and the effective pulp-settling area of the classifiers, a total of 1 sq. ft. of pool area was required per ton of dry feed per day for the thickening and washing operations. The washing efficiency in the test was 95 pct.

Jan 1, 1960

By Charles Vaught, Jeff Duncan, Michael J. Brnich, Lisa J. Steiner

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.3 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Remote control and extended cut miner operators and face crews Length: Eight questions (30 minutes for administration plus 30 for discussion) Skills: Remote control mining procedures including remote control mining, taking extended cuts, resetting breaker on mining machine, and setting timbers. Communicating mine conditions, influencing safe behaviors when mine conditions are less than stable Location: Underground coal mine, four section continuous mining operation Average seam height is 48 inches Problem: Your regular job is on the general labor crew at Cripple Creek #9 mine, a four section continuous mining operation. The mains are 9 entries wide and panels are 5 entries across. You and the rest of the crew had annual refresher training about 3 months ago. For the past few days you have been sent to 2 South panel to fill in as the third shuttle car operator. This morning, however, your buggy is down. The face boss asks you to get the scoop and take seven or eight timbers to the number 5 entry because the last shift got off sight line. The miner will be working in entry 5 while the bolter crew pins entry 4. When you get up to the face you see that Mo, the remote control continuous miner operator, has rounded off the left inby corner in order to make his first cuts in the right hand rib. Now, he has squared around enough so that you and Red, the miner helper, can set some posts on the corner. The two of you set posts along the left inby rib of #5 entry while the shuttle car operator waits. You are in a tight spot when Mo decides to start mining. You must decide where the best place is to stand for safety and to be out of the way.

Jan 10, 1999

By R. D. Leitch

"INTRODUCTION The general program of the investigation of coal mine drainage which the Bureau of Mines is making includes, among its many phases and objectives, a study of the fate of the acid, content of drainage after it enters natural streams, and the effect of seasonal variations on the degree of contamination of streams. Opportunity for studying these under comparatively normal conditions and variations can readily be found, but there is only a chance opportunity for studying than under extreme conditions. The unusual drought that prevailed during the summer of 1930, however, created a condition of low water favorable to a study of one of the extremes.This report gives the results of an investigation of Bennett Branch of Sinnemahoning Creek, Pa., made under this condition.ACKNOWLEDGMENTSThis work was conducted under the direction, and with the advice, of Dr. R. R. Sayers, chief, Health and. Safety Branch, and of W. p. Yant, supervising engineer, Pittsburgh Experiment Station.DESCRIPTION OF BENNETT BRANCHBennett Branch, as shown in Figure 1, is a tributary to Sinnemahoning Creek. Its source is in Huston Township, northwestern Clearfield. County, from which it flows in a general northeasterly direction through Elk County, thenceeasterly in Cameron County to Sinnoning Creek at Driftwood. The total length is about 37 miles. There are nine towns along the stream that have an average population of about 350. There is no industrial pollution other that from coal mines and very little. domestic, pollution."

Jul 1, 1931

Although the technology involved in removing material from below the earth's surface has a long history, communication systems in underground workings are relatively new to the industry. Communication equipment did not begin appearing in underground mines until the early 1900's. Figure 1-1 shows a miner using a Western Electric standard telephone set for underground mines in 1913. These early phones were essentially the same as those used aboveground, except that they were enclosed in cast-iron boxes as protection against moisture, acid fumes, and gases. In the 1950's, the Chesapeake and Potomac Telephone Co. of West Virginia introduced a telephone set for use in explosive atmospheres that was designed around the philosophy of explosion containment. To contain an explosion within the telephone set required a 39-pound casing, which greatly limited portability. [ ] Both of these telephone sets required "pipe" or conduit, not a very practical item for a 100-squaremile coal mine. A common thread prevalent in the first 40 years of design and development is that the primary effort was placed on the telephone set. In the early 19701s, as work began on the design of modern communication systems for use in underground mine environments, the following requirements were established: 1. Must meet intrinsic safety standards .--This applies not only to coal mines, but to other explosive environments. 2. Must be compatible with the environment.--The system must with- stand dust, moisture, and corrosive conditions. 3. Must be rugged in structure.-- The system must withstand maintenance by 10-inch pliers and 4-pound hammers, as well as impact from a falling piece of roof. 4. Must be size-flexible.--Whatever is built must be sized for the small operator as well as the large companies. 5. Must be a total system in design.--The system must be intrinsically safe, including cable, power supply, and station set. 6. Must work with present telephone system.--The system should be compatible with aboveground communications already in place; it should not be the single cause of change in aboveground communications. 7. Value-added pricing.--The system should be reasonably priced so that savings created by its introduction will more than offset the installation cost.

Jan 1, 1984

By A. F. Colombo, R. T. Sorensen, D. W. Frommer

The Bureau of Mines developed a flotation method for concentrating spiral tailing produced from pilot plant tests on the Champion mine ore fines . The feed material contained about 49 percent Fe and 15 percent SiO2 and was posed mostly of specular hematite , muscovite , and chlorite . Bench- scale , batch flotation research developed a reagent suite composed of tall oil - fatty acid , fuel oil , sulfuric acid , sodium fluoride , and sodium silicate for recovery of iron minerals in the froth product . Concentrate made with the reagent suite contained 87.3 percent of the iron and analyzed 65.6 percent Fe and 1.9 percent SiO2 . Continuous flotation tests were made with a nominal feed rate of 400 lb /hr , but without middling recirculation . Using nearly the same amount and complement of reagents as in the batch tests , three similar continuous tests gave concentrates averaging 63.9 percent Fe and 3.1 percent Sio while recovering about 86 percent of the iron .

Jan 1, 1964

By A. J. Kraemer, O. C. Blade

This report on the properties of commercial motor fuels sold in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee of the Cooperative Research Council (C.R.C. ) and the Bureau of Mines of the United States Department of the Interior . The first report contained data on motor gasolines sold during the winter of 1935-364 . Further reports on motor gasolines sold during the succeeding summers and winters to the summer of 1941 have been issued . No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942 . The present report presents analytical data for 1,120 samples , representing the products of approximately 88 companies . As in previous surveys , these companies include both large and small suppliers . In addition, the Pacific coast is represented by data averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were received . Conforming to previous surveys , the data cover three groups of samplesregular - price , premium - price , and third - grade gasolines and each group has been averaged separately. The number of samples , items and brands comprising each group, exclusive of those of the Pacific coast, are as follows : Regular price , 641 samples , 250 items , and 64 brands ; premium price , 439 samples , 222 items , and 68 brands ; third - grade gasoline , 50 samples , 50 items and 19 brands .

Jun 1, 1943

By Walter R. Storms, Allan B. Bowman

This paper , which describes mining methods and practices at the Mineral Hill copper mine , is one of a series being prepared by the Division of Minerals of the Bureau of Mines on mining methods , practices , and costs in various mining districts. of the United States . The Mineral Hill mine is situated on the northeastern piedmont of the Sierrita Mountains at an altitude of 3,650 feet in sec . 35 , T. 16 S. , R. 12 E. , and sec . 2 , T. 17 S. , R. 12 E. , Pima mining district , Pima County , Ariz . ( fig . 1 ) . The claims (figs . 2 and 3) are in a gently rolling area with only scant desert vegetation . The average annual precipitation is about 11 inches . The nearest surface water is the Santa Cruz River , an intermittent stream 8 miles east of the mine . The property is owned by the Banner Mining Co. , a Nevada corporation . This report presents a brief history of the mine , describes the geology of the area and the ore deposits , outlines methods of prospecting and exploration , and gives methods of sampling and the estimation of ore reserves and values . Development and stoping methods are explained , and methods of underground transportation , ventilation , mine drainage , and safety measures are described . The concluding section of the paper is a section on milling . The Mineral Hill mine is an old mine that was reopened in 1951 after having been closed for 30 years .

May 1, 1957

By R. G. Meara, O&apos

The land-pebble district of Florida, wnich in 1928 supplied 96.7 per cent of the phosphate production of that State and 82 per cent of the domestic requirements of the United States, is centered in Polk and Hillsboro Counties about 30 miles east of Tampa The deposits are unconsolidated sediments occurring as beds of phosphate matrix overlain by a mantle of barren sands and clays. The matrix consists of a mixture of sand (quartz grains), clay, and phosphate rock in which the coarsest sand is much finer than the coarsest phosphate; that is, the sand is segregated in the fine material. Before the introduction of classifiers the concentration consisted of log washing, and screening at about 20-mesh, which was usually the finest size that could be taken to maintain commercial grade, 66 per cent B. P. L. (bone phosphate of lime) or more. When classifiers were introduced some of the fines that had escaped at the head of the washery and some of the minus 20-mesh material isolated during the washing and formerly lost supplied the feed. During October, 1927, the United States Bureau of Mines in cooperation with the University of Alabama and the Missouri School of Mines and Metallurgy began to investigate the amenability of phosphatic sands to gravity methods of concentration. The work was under the immediate supervision of B. W. Gandrud, acting supervising engineer of the Southern Experiment Station of the U. S. Bureau of Mines at Tuscaloosa, Ala., and Will H. Coghill, supervising engineer of the ore dressing section of the U. S. Bureau of Mines. More comprehensive testing followed and in the early part of 1930 some of the companies cooperated with the bureau and the above-mentioned institutions in conducting a series of tests on hydraulic classification and tabling. The results indicated that marketable concentrates could be obtained with a recovery of 25 to 45 per cent of the phosphate formerly lost. As a result two companies have introduced hydraulic classification to treat the current tailings, and one of them has substituted classifiers for the 20-mesh screens which had been unsatisfactory. Because the phosphate grains and quartz grains have nearly the same specific gravity, the use of concentrating tables by the customary methods is not applicable. The washeries included in the following report are designated as Nos. 1, 2, and 3.

Jan 1, 1931

By H. H. Schrenk, F. E. Griffith

"The increase in tunneling operations that requires working under pressures greater than that of ordinary atmosphere has raised the question of the use and possible limitations of respiratory protective devices under such unusual conditions. As little, if any, information is available, there is need for a comprehensive study of this subject before specific recommendations can be made. In the absence of such data it seems desirable to make a few preliminary observations regarding the problems associated with wearing respiratory protective devices under increased air pressures.Two distinct problems must be considered--the mechanics of the apparatus used under such conditions and the physiological effects of increased pressures on wearers of respiratory apparatus. This report is confined to the use of oxygen breathing-apparatus and gas masks under pressure.ACKNOWLEDGMENTSThe data presented were obtained at the Queens Midtown Tunnel under construction at the east end of 42d Street, New York City, during a study of compressed-air illness conducted by the Bureau of Mines in cooperation with the United States Public Health. Service and the New York City Tunnel Authority.Grateful acknowledgment for cooperation and the use of facilities is made to Dr. R. R. Sayers and his associates, particularly Dr. J. W. Crosson (who acted as observer during the oxygen breathing apparatus tests), of the Division of Industrial Hyiene, National Institute of Health; to the Port of New York Authority, through Dr. Edward Levy; end to the contractors, through Doctor Emery."

Jan 1, 1940

By David Schlain

The galvanic corrosion properties of titanium in contact with commercially pure aluminum, copper, or type 302 stainless steel in some of the common organic acids were investigated. Acids used in these experiments were 10 percent formic, acetic, lactic, citric; 1 percent oxalic and tartaric; and 9 percent oxalic. Electrode-potential measurements and several types of galvanic couple experiments were carried out. Solutions were aerated by three methods: Flow of air, flow of helium, and natural aeration. Work was done at 35° C. with couples consisting of equal areas of the 2 metals. Titanium was resistant to corrosion in most of the organic acids studied, whether alone or in contact with a dissimilar metal. However, titanium coupled with aluminum did corrode in 1- and 9-percent oxalic acid solutions. Contact with titanium usually caused aluminum to corrode by galvanic action. Copper was subject to galvanic attack in 10-percent acetic acid with a flow of air. Contact with aluminum to some solutions in which titanium is ordinarily inert and noble with respect to aluminum caused titanium to corrode

Jan 1, 1956

By C. W. Davis

Two general schemes have been used for the determination of gold and silver in material containing considerable quantities of copper ; one is known as the " all fire " method , and the other as the , " combination " , or " wet and dry" method . The all fire crucible method , using an excess charge of litharge , has been found satisfactory when the copper content of an ore is under 6 per cent , ( Loevy , J. , Zur Edelmetallbestimmung in hochprozentigen Kupfererzen : Chem. Ztg . Jarhrg . 35 , 1911 , p . 278 ) , or where the precious metal value is so great that a small sample can be used . In the latter case , silica is added until the copper ratio is sufficiently low . If there is more than 6 per cent of copper in an ore , the lead button obtained from a crucible fusion will require repeated scorification before . it can be cupelled successfully . Rescorification is not only tedious , but also causes a slag loss of precious metals . In combination methods , the copper is dissolved , and the gold and silver in the residue . is determined by fire assay Although some combination methods have given satisfactory results for gold and silver , they are not applicable when an estimation of the platinum metals is required . Since substances containing platinum are frequently high in copper , a study of methods which might be used for the estimation of small quantities of gold , silver , and the platinum metals in such material was considered worth while . The estimation of platinum in ores by fire assay methods has been described in Technical Paper 270 of the bureau; ( Davis , C.W. , The detection and estimation of platinum in ores : U. S. Bureau of Mines Tech . Paper 270 , 1921. ) the present paper , which is supplementary to that report , deals chiefly with the application of combination methods , taking them up to the point where the fire assay is to be applied .

Mar 1, 1921

By R. V. Ramani, V. T. Burgos, J. A. McClay

Summary Cost models have, long been confined to the accumulation and analysis of static-data.. While historical and time study data are valuable for control of existing operations, for new systems and equipment, and for projections, they need to be adjusted or modified. The availability of computer-oriented systems simulators provide yet another method for costing these systems and equipment. This investigation has introduced a concept whereby continuous, variable data can be assimilated and analyzed through the combination of an economic analysis model, which includes a direct costing capability, with a systems simulator. This tandem operation permits increased flexibility and greater atten¬tion to detail in the evaluation of mining systems. The direct costing process is carried throughout the majority of the model operations. Labor and capital costs may be computed directly, even in the absence of the systems simulator, while operating costs re¬quire input parameters, at present, from the subsystems of the Master Design Simulator. Since the costs computed are based on the perfor¬mance of each individual machine unit, the model may be used to evaluate equipment compatibility, system interaction at the mining face, and the effect of system elements on total mining costs. Additional applications of the cost model include the following: 1. Complete mining systems may be evaluated, over their economic life, to determine the feasibility of a profitable operation. 2. Costs associated with mining various segments of the coal deposit may be computed as a guide to planning the mine layout and scheduling the sequence of operations or acquisition of new

Jan 1, 1975

By R. V. Ramani, V. T. Burgos, J. A. McClay

Cost Data Library The data retained in the Cost Data Library is of a semi¬permanent nature in that it is held in storage for immediate use with the program although its contents may require periodic evaluation to maintain it in a current status. The library is composed of six arrays containing both technical and cost data. The following description of the library input system provides the information necessary to maintain an active storage file. Array POWERA: FORMAT (8F10.0) - contains the step groupings of the power rate schedule for power cost computations. Four input data cards are required to fill this storage area. Card Column 1 1 - 10 Demand in Kilowatts for the First Step of the Demand Rate Schedule 11 - 20 Demand in Kilowatts for the Second Step of the Demand Rate Schedule y 41 - 50 Demand in Kilowatts for Fifth Step of the Demand Rate Schedule 51 - 60 Maximum Demand Level for this Rate Schedule 61 - 70 Percent Power Factor for this Rate Schedule 71 - 80 Unassigned 2 1 - 10 First Step Demand Charge, $/Kw 11 - 20 Second Step Demand Charge, $/Kw 4¬ 41 - 50 Fifth Step Demand Charge, $/Kw

Jan 1, 1975