Search Documents

By Sean Gallagher

The restricted workspace present in low-seam coal mines forces workers to adopt awkward working postures (kneeling and stooping), which place high physical demands on the knee and lower back. Method: This article provides an analysis of injury claims for eight mining companies operating low-seam coal mines during calendar years 1996-2008. All cost data were normalized using data on the cost of medical care (MPI) as provided by the U.S. Bureau of Labor Statistics. Results: Results of the analysis indicate that the knee was the body part that led in terms of claim cost ($4.2 million), followed by injuries to the lower back ($2.7 million). While the average cost per injury for these body parts was $13,100 and $14,400, respectively (close to the average cost of an injury overall), the high frequency of these injuries resulted in their pre¬eminence in terms of cost. Analysis of data from individual mining companies suggest that knee and lower back injuries were a consistent problem across companies, as these injuries were each among the top five most costly part of body for seven out of eight companies studied. Application/Impact: Results of this investigation suggest that efforts to reduce the frequency of knee and low back injuries in low-seam mines have the potential to create substantial cost savings.

Jan 1, 2009

By D. E. Traut

The effect of various ion concentrations on uranium absorption from a sodium carbonate solution by a strong-base, anion resin was investigated by the Bureau of Mines in support of its objective to help assure an adequate uranium supply for future needs. The studies were conducted to improve the recovery of uranium from in situ leach solutions by ion exchange. The effects of carbonate, bicarbonate, chloride, and sulfate ions were examined. Relatively low (less than 5 g/l) concentrations of chloride, sulfate, and bicarbonate were found to be detrimental to the absorption of uranium. High (greater than 10 g/l) carbonate concentrations also adversely affected the uranium absorption. In addition, the effect of initial resin form was investigated in tests of the chloride, carbonate, and bicarbonate forms; resin form was shown to have no effect on the absorption of uranium.

Jan 1, 1979

By Thomas J. Fisher, John J. Sammarco, Gary L. Mowrey, Edward F. Fries

This report (Safety File 3.0) is the fourth in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 5, 2002

By Lloyd A. Morley, Robert Stefanko

In addition to explosion-proof enclosures, the IEC has published recommendations: 1. 79-2 Pressurized Enclosures, 2. 79-3 Intrinsic Safety, 3. 79-5 Sand-Filled Apparatus, 4. 79-6 Oil-Immersed Apparatus, and 5. 79-7 Increased Safety. All these are valid methods of electrical hazard reduction and find wide use in industries other than mining. Magison (52) discusses in detail each technique and, therefore, such an examination will not be repeated. Two other systems, lamina and labyrinth, are but variations of common explosion-proof enclosures and, therefore, will not be cov¬ered. (34,35,46,53,54,61) By examining other national authorities' opinion, the following will investigate each system's applicability to coal mining. Intrinsic safety applies to any system which is incapable of re¬leasing sufficient energy to be an electrical hazard. (49) Not one foreign country contacted disagreed with the concept, and they find these systems totally acceptable. Only South Africa does not accept oil-immersed apparatus, but no reasons were given. (62) Healy (27) stated that Queenlands, Austrailia would accept all techniques, yet some were still to be employed. Japan specifications allow for all but sand filled. (42,43) Increased safety or Protection Type "e" is an approach in hazard reduction in which special design considerations are applied to ensure an extremely low probability of electrical or mechanical breakdown

Jan 1, 1974

By John W. Thatcher

A demountable X-ray tube vacuum spectrograph was designed by the Bureau of Mines for the determination of long-wavelength X-ray spectra from the light elements. This instrument was operated for both secondary and combined primary-secondary excitation of the aluminum K-series. There was an increased analytical sensitivity for elements in period 3, and an indication that with improved X-ray tubes or direct election excitation of the sample, X-ray determination of elements in period 2 is also possible.

Jan 1, 1965

By S. L. May

Investigations by the Federal Bureau of Mines indicate that hafnium and zirconium compounds of acceptable purity can be extracted from Nigerian zircon concentrates. Chlorination and caustic soda fusion techniques were used to extract 85 to 95 percent of the valuable metals from the concentrate. The extracted hafnium and zirconium compounds were purified by recrystallization of the oxychlorides or by formation of complex salts during chlorination. The zirconium-hafnium product of the recrystallization method contained 15 parts per million of uranium, and the product of the salt-complex method contained less than 10 parts per million of uranium. The hafnium was separated from zirconium by solvent extraction methods. A zirconium product containing 0.3 percent hafnium and a hafnium product containing 4 percent zirconium were obtained. At the request of the Atomic Energy Commission (AEC), work was started to develop techniques for processing Nigerian zircon concentrates in commercial installations presently engaged in producing zirconium and hafnium metals from ores. The Nigerian zircon has a high hafnium content, but the presence of uranium and thorium is a problem not normally encountered in processing zircon concentrates.

Jan 1, 1961

By Arno C. Fieldner

Coal for coke production is fundamentally necessary for the manufacture of pig iron , and pig iron must be had for making steel - a vital element in our modern industrial economy . In both World Wars , special effort by Government and industry was required to meet the emergency of greatly increased demands . In the first World War , lack of coke - oven capacity , rather than lack of coking coals , was the principal problem ; but in the second World War both oven capacity and coking -coal mining capacity were pushed to the utmost . Because of inadequate supply , it became necessary to allocate a part of the production of these coals from other fuel use to coke production . This was done by the Solid Fuels Administration . These experiences raised a question , during and after the war, as to the nature and amount of the minable reserves of coking coal suitable for the manufacture of metallurgical coke ; and to what extent the lower -rank and lowergrade coals could be utilized by improving preparation and by appropriately blonding different coals . Obviously , much investigation and research are required to find answers to these questions . Somo work was done by Governmental and industrial agencies during the war , and , fortunately , more has been undertaken since the close of It is the purpose of this paper to review briefly our fuel reserves , with special reference to coking coal , and to discuss the problems of utiliz . ing progressively poorer coking coals as the reserves of high - quality coals approach depletion .

Mar 1, 1950

By D. G. Kesterkel

Low-melting thoriurnrbase binary alloys or metal solutions were prepared by two different techniques involving the electrolysis of ThO2 dissolved in fluoride melts. Experiments were performed at 950° to 1,250° C using electrolytes containing ThF4 and various alkali and alkaline earth fluorides. In the first method, electroreduction of ThO2 and deposition of thorium on a nickel or iron cathode formed a molten alloy that dripped off and collected on the bottom of the cell, or in a tungsten cup. An electrocodeposition technique was used to prepare thorium-base alloys or solutions containing nickel, iron, chromium, or manganese. Electrolytic reduction of the component metal oxides and simultaneous deposition of the two metals on a tungsten cathode yielded a liquid alloy product. Complementary experiments were performed on the fused fluoride electrowinning of dendritic thorium from Th02 at 1,075° to 1,200° C in which thorium crystals were recovered and arc-melted into buttons. Major contaminants were aluminum, carbon, copper, iron, oxygen, and silicon, totaling 0.2 percent.

Jan 1, 1966

By Jack R. Woodyard

Scientists at the U.S. Bureau of Mines are studying iron aluminides as possible substitutes for stainless steels to reduce the Nation's dependence on imported strategic and critical materials. In a Bureau investigation on the mechanical properties of Fe-28Al, it was found that the material's machining properties were significantly improved at slow tool and feed speeds. Machining techniques normally used for brittle materials failed or were costly. Further experiments using a 5-in (12.7-cm) mill cutter with carbide inserts, operating dry at minimum machining speeds, produced visually smooth sample surfaces with no tool damage. As a result of these experiments and a review of published data on hydrogen embrittlement of iron aluminide under tension, non-water-based (e.g., sulfur-based) lubricants were chosen for production machining. Four-flute, 3/4-in (19-mm) carbide end mills were used at slow speed under lubrication. This latter procedure reduced tool wear and breakage by a factor of 2. Machined surfaces and specimen cross sections were analyzed by scanning electron microscopy to detect microcracking. Tensile tests gave the expected yield and ultimate strengths, indicating that no degradation by low-speed machining occurred. This study extends this work to show that the alloy can be machined at higher speeds using high-speed steel end mills, and that water-soluble cutting oil is a suitable lubricant and coolant.

Jan 1, 2010

By E. G. King

The work described in this Bureau of Mines report was undertaken to fill a need of industry for high-temperature heat-content data for uranium tetrafluoride. Without such data, heat balance evaluations of processes involving this substance are seriously hampered. Measurements of the heat content of uranium tetrafluoride were conducted at temperatures from 298° to 1,350° K. The melting point and heat of fusion were determined. The results are presented in suitable tabular form, and representative heat-content equations are included.

Jan 1, 1961

By B. J. Dalton

The Bureau of Mines Helium Research Center has developed a computer program for solving two-phase equilibria data for binary mixtures and for evaluating thermodynamic functions of interest, including all critical points. This computer program was used to calculate equilibrium points on the PVTu surface for the helium-nitrogen system as predicted by the Van der Waals equation of state. Numerical values are tabulated and illustrations are presented for 1,279 equilibrium points and for quantities needed to construct Ponchon diagrams. Equilibrium ratios as a function of pressure at constant temperature and of temperature at constant pressure-are also shown graphically. In addition, saturated partial molal volume and partial molal enthalpy data are given. It is shown that the Van der Waals helium-nitrogen system exhibits retro-grade condensation of the second type for liquid helium concentrations of about 0.07 mole fraction or less and pressures below about 45 atm. It is also shown that the critical point is at a -maximum value of pressure (at constant temperature) and of temperature (at constant pressure).

Jan 1, 1971

By J. J. Demeter

A tube-wall reactor with a Raney nickel catalyst deposited on the outer wall of the tube by flame spraying is effective in the practically complete conversion of 3H2+1CO synthesis gas to a high-Btu gas (methane) at an hourly space velocity of 7,000 volumes of gas (NTP) per hour per volume of annular volume. Partially reacted synthesis gas containing an appreciable amount of methane can also be treated in this reactor to increase the heating value to over 900 Btu per cubic foot. Excellent heat removal through the metal wall to a coolant and temperature control were obtained. The heat transfer co-efficient from the catalyst to the coolant was about 275 Btu per hour per square foot per ° F. Synthesis tests were conducted with tubes 1.2 inches in ad by 6 inches long, and 1.3 inches in od by 36 inches long. When operating at a synthesis gas rate of 100 to 120 scfh per square foot of catalyst-coated tube, catalyst life was long enough to realize a catalyst cost for the raw Raney nickel alloy of about 0.3 cent per 1,000 cubic feet of pipeline gas (900 to 950 Btu per scf). Gas recycling at ratios of 1:1 to 3:1 was effective in increasing conversion and in extending the life of the catalyst to about 16 weeks. In cost and in operating characteristics the tube-wall reactor compares favorably with the fluidized-bed and hot-gas-recycle reactor systems for the synthesis of high-Btu gas from H2+CO.

Jan 1, 1967

By E. M. SEELEY, F. S. LOTT

The total capacity of the natural-gasoline industry to produce light hydrocarbon products increased to 21,322,000 gallons ( 507,670 barrels ) daily on January 1 , 1948 , from 17,928,000 gallons ( 426,860 barrels ) daily on January 1 , 1946. Expansion of the industry in the first two post -war years , 1946 end 1947 , thus averaged 9 percent annually , compared with 6 percent annually in the last two war years , 1944 and 1945 . The number of cycle plants increased only from 37 to 39 in the years 1946 and 1947 , and total capacity of these plants gained 21 percent to 5,857,000 gallons de ily on January 1 , 1948 , represent ing 27.5 percent of the total capacity of the industry , compared with 27.0 percent on January 1 , 1946. All other plants decreased in number in the two-year period from 589 to 510 on January 1 , 1948 , but their total daily capacity increased 18 percent to 15,465,000 gallons . The daily capacity of the average plant in the industry was enlarged from 28,600 gallons on January 1 , 1946 , to 38,800 gallons on January 1 , 1948 , continuing the long -established trend to producing units of greater size and efficiency . The average cycle plant capacity increased from 131,000 gallons daily to 150,200 gallons daily on the same dates as the average capacity of all other natural -gasoline plants increased from 22,200 gallons to 30,300 gallons . Owing to the elimination of small , obsolescent plants in Illinois , Oklahoma , and Pennsylvania , these States experienced the greatest reductions in numbers of plants in 1946 and 1947. In Oklahoma and Texas , several consolidations of two or more plants into a single operating unit were reported . Louisiana and Mississippi were the only States in which the number of plants increased , but daily capacity to produce light products was larger in eleven States on January 1 , 1948, than two years earlier . Added facilities in California and Texas accounted for 41 and 36 percent , respectively, of the national gain in capacity .

Sep 1, 1948

By John W. Kopp

A major concern with blasting at surface mines is generation of ground vibrations and airblast and their effects on nearby residences. This Bureau of Mines report looks at the use of millisecond delays in blast design and their effect on the resulting ground vibrations and airblast. A total of 52 production blasts were instrumented and monitored at a surface coal mine in southern Indiana. Arrays of seismographs were used to gather time histories of vibrations and airblast. The data were analyzed for peak values of vibration and airblast and for frequency con-tent. Various delay intervals were used within and between rows of blastholes. Delay intervals within rows were 17 and 42 ms, and those between rows ranged from 30 to 100 msj these intervals are equivalent to 0.5 and 1.3 ms/ft within rows and 1.2 to 4.3 ms/ft between rows. Sub-sonic delay intervals within rows reduced airblast by 6 dB. Large delay intervals between rows reduced the amplitude of ground vibrations; their frequency depended primarily upon the geology of the mine site.

Jan 1, 1986

By C. J. Chindgren

The Bureau of Mines investigated the technical problems involved in recovering commercial-grade vanadium products from alkaline solutions of low vanadium content. Conditions were defined for precipitating calcium vanadates from sodium vanadate solutions with calcium chloride and calcium hydroxide and for dissolving the precipitates with acid, sodium carbonate, and sodium bicarbonate to obtain vanadium-enriched solutions from which either red cake or ammonium metavanadate was recovered. Calcium vanadates with CaO:V205 mole ratios of 2, 3, and 4 were produced with recoveries of 93 to 100 percent. Optimum recovery of the low-lime variety of calcium vanadate was obtained by employing excess calcium chloride and adjusting the pH to a range of 8.0 to 8.5. High vanadium extractions were obtained in concentrated solutions by dissolving the calcium vanadate precipitates with any of the reagents tested. The resulting extracts contained 25 to 125 grams V205 per liter. Conventional procedures used to precipitate either red cake or ammonium metavanadate from the enriched solutions gave excellent vanadium recoveries.

Jan 1, 1967

By H. H. Dewing

The Bureau of Mines conducted a laboratory-scale investigation of a technique that produces zinc sulfate and elemental sulfur from sphalerite concentrates by reaction with sulfuric acid at 175° to 200° C and ambient pressure. The objective of the investigation was to develop a hydrometallurgical method of producing zinc from sulfide concentrates that does not generate sulfur dioxide pollutants. Reaction with 80-to 85-pct sulfuric acid produced 4 moles of sulfur for every 3 moles of sphalerite reacted, with minimal production of sulfur gases under optimum conditions. More than 98 pct of the zinc was recovered as zinc sulfate after 3 hours at 175° C. The reaction mixture was leached with simulated spent zinc electrolyte containing 13-pct sulfuric acid to recover zinc sulfate from the insoluble, high-sulfur residue. Neutral zinc sulfate, which is required for electrolysis, was separated from the sulfuric acid solution by crystallization as ZnS04?7H20 at -10° C. Up to 80 pct of the water in the recycled electrolysis solution was removed by the crystallization process; evaporation was used to further concentrate the sulfuric acid for reuse in leaching sphalerite. Advantages of the proposed method over conven-tional roasting and leaching include virtual elimination of sulfur dioxide, production of a solid sulfur byproduct, and higher zinc recoveries due to elimination of zinc ferrite losses.

Jan 1, 1978

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making; and (3) to upgrade marginal coals through effective preparation. This is the second7j of a series of reports giving the results of studies by counties under part (1) of the investigation. This report covers Indiana County, Pa., which comprises parts of the Smicksburg, Punxsutawney, Elders Ridge, Indiana, Barnesboro, Latrobe, New Florence, and Johnstown Quadrangles. (See fig. 1.) A base map for each bed in each Quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1950

By Dave P. Cooper, Tim D. Burgess, Dean H. Ambrose

This paper discusses the application of digital human models (DHM) to examine computer generated forces necessary to move specific joysticks by using roof bolter virtual operators to predict the forces experienced on the operator’s upper extremities. Using DHM and simulations of static movements, investigators analyzed predictions of joint moment and joint force effects on virtual operator’s right wrist, elbow and shoulder and compared them to different body dimensions and work postures. This study exemplifies the ease of estimating upper extremity loads on equipment operators using virtual operators and computer models of equipment and work environment. As expected, comparing results of percentage of joint force and moment reduction using the electronic control and of the mechanical control showed that the electronic control had lower joint forces and joint moments over the mechanical control. The average predicted value of the joint moment on the wrist was 1.84 Nm, elbow 7.85 Nm and shoulder 14.55 Nm and of the joint force on the wrist was 5.06 N, elbow 4.56 N, and shoulder 3.67 N. Because the data illustrates low-level forces to move a joystick, inadvertent actuation of the control is addressed. Regardless of the findings, research is still needed on joysticks in real world situations such as an epidemiological assessment of equipment operators in the field before final recommendations and conclusions can be drawn.

Jan 1, 2007

By John Taber, Robert D. O'Brien

"INTRODUCTION The Bozeman corundum deposit was first examined in May 1944 by an engineer of the Bureau of Mines. In August 1944, the property was re-examined because of a sharply increased war demand for corundum. A small program of trench exploring was undertaken after the second examination. The work was started in October 1944 and was completed in December 1944. This report presents the essential data obtained by the exploratory work.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that, they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploration work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests.The field work on the Bear Trap project was supervised by E. W. Newman, district engineer Montana District office. The microscopic examinations and. the grid grain-count analyses of the samples and the beneficiation tests were made at the Bureau's laboratory at Salt Lake City, Utah, under the direction of S. R. Zimmerley, chief, Salt Lake City Division, Metallurgical Branch."

May 1, 1947

Lower the respirable dust exposure of longwall shearer operators by isolating and con-fining the dust cloud near the face. Approach Install conveyor belt screens at various locations on the body of the shearer to contain and hold the dust cloud toward the face side of the machine. This approach provides a cleaner air split in the walkway, over the shearer operators. How It Works On most longwall shearer sections, the dust exposure of the shearer operators is primarily attributable to the machine it-self. The dust cloud originates at the face, and the exposure of the operators depends largely on how quickly this dust spreads into the walkway. Conveyor belt screens placed on the gob side of the body of the machine can reduce the amount of dust which spreads out into the walk-way. In addition, belting may be installed over any open spaces between the shearer under-frame and the panline to prevent conveyor dust from boiling out into the operator's walkway.

Jan 1, 1981