Search Documents

By R. F. Linfield

Figure 1-1 shows the basic transmitter design concepts used for the pulse system, the half-wave CW system, and the full-wave CW system. The antenna current waveform is also shown for each transmitter for typical operating frequencies and antennas. The switches shown in Figure 1-i were actually implemented using solid state devices. In all three systems the signaling format may be interrupted to conserve power and thereby extend battery life. Frequency accuracy and stability is achieved using a tuning fork oscillator in the transmitters and tuning fork filters in the receivers for all three systems. This provides the narrow reception bandwidths needed to enhance signal detectability. All three systems also use frequency assignment for identification purposes. The location schemes employed are likewise identical, each being based on detecting the null (signal minimum) of the horizontal magnetic field on the surface. Since these systems are basically similar, the primary purpose is to select the system which gives the maximum signal detectability on the surface from a manpack transmitter operating in the mine. Both the pulse and half-wave C W systems use a d. c. pulse to energize the loop antenna. However, with the pulse system, this pulse duration is short compared to the pulse repetition rate (prf), whereas with the half-wave C W system the pulse duration equals one-half the period of the switching frequency. In the pulse system, energy from the battery is stored in a capacitor so that during the switching interval the internal resistance of the power source can be considered almost negligible. Both transmitters must drive a loop antenna which is a reactive load having inductance, L, and resistance, Ra.

Jan 1, 1973

By John S. Ball

Aniline points have been used to some extent for more than 20 years. to indicate the types of structures in hydrocarbons and thus to analyze mixtures of hydrocarbons . This type of analysis has been applied - principally to the low -boiling hydrocarbons found in the gasoline range . Although there is some disagreement as to their merits , both aniline point and diesel index (aniline point in degrees Fahrenheit times A.P.I. gravity at 60 ° F. divided by 100) are used rather extensively for evaluating ignition qualities of diesel fuels . In recent years aniline points have been employed in the study of lubricating - oil fractions . They also have been used to predict : the tendency of different oils to cause swelling of synthetic rubbers.5/ Recent standardization of the aniline - point determination by the American Society for Testing Materials has encouraged wider use of this test . Considerable data concerning , aniline points and critical solution temperatures in aniline have been accumulated in the course of a study of related subjects . Thesc data , together with some original results , are presented here in the hope that they will prove useful to other worker's in this field ...

Oct 1, 1943

By G. B. Atkinson

To develop technology to help assure an ample domestic supply of zinc, the Bureau of Mines is investigating an aqueous chlorine-oxygen leaching process for treating complex sulfide concentrates. This report discusses the purification of aqueous C12-02 leaching solutions by utilizing zinc cementation to remove Cd, Co, Cu, Ni, and Pb. Additional processing of the purified solution is necessary to produce ZnC12 crystals suitable for molten-salt zinc electrowinning cells. The effects of solution temperature, reaction time, zinc dust concentration, ZnCl2 concentration, and degree of agitation on the removal of impurities were investigated for both simulated and actual leaching solutions. Zinc dust addition to a leaching solution at 30° C decreased the Cd, Cu, Ni, and Pb concentrations to acceptable levels of less than 3 mg/1 each. By increasing the solution temperature to 75° C, the cobalt content was decreased to less than 5 mg/l, an acceptable level for producing electrolytic cell-grade ZnC12. Impurity removal rates from ZnCl2 solutions are Pb>Cu=Cd>Ni>>Co. An increase in the solution temperature increases the rate of removal for these metal impurities.

Jan 1, 1982

By C. P. Bowie

For years many oil producers have believed that often low-pressure oil- and gas-bearing strata have been over coked in fields where the rotary system of drilling has been used. Collom3/ gave as a reason for this condition that because the mud fluid was thick, the oil or gas stratum was plastered and sealed as the tools passed through it and no oil showed at the surface. Although this observation was made 15 years ago, it may often still be true notwithstanding modern developments in coring and electrical logging. Operators have believed, also, that mud fluid does not solidify behind the casing. Lewis and McMurray4/ stated: "All the evidence obtainable from practical experience points to the fact that the mud fluid properly mixed and employed does not solidify behind the casing, even in deer wells and after long periods."

Jan 1, 1937

By W. M. Traver

As a direct result of the second World War, consumption of nickel in the United States has increased to such an extent that it has been considered timely to investigate undeveloped deposits of the nickel minerals. Funds were made available to the Bureau of lines in 1941 to investigate the extent, occurrence, and quality of nickel ores in the Mirror Harbor area. The Federal Geological Survey mapped' and studied the area during the summer of 1941 and Robert S. Sanford, an engineer of the Bureau of lines, made a preliminary examination in June 1942. A contract for drilling the deposits under the direction of the author was let in July 1942.

Jan 1, 1948

By Michael E. Henderson

Presented in this report are the experimental results of coarse coal slurry degradation data obtained from the Hydraulic Transport Research Facility (HTRF) at the Pittsburgh Research Center (PRC), Bruceton, PA. The facility is operated by Boeing Services International, under Bureau of Mines Contract No. J0333956. Presented in this report are the experimental results of coarse coal slurry degradation data obtained from the Hydraulic Transport Research Facility (HTRF) at the Pittsburgh Research Center (PRC), Bruceton, PA. The facility is operated by Boeing Services International, under Bureau of Mines Contract No. J0333956. This particle degradation report is a summary of the particle distribution data obtained at the HTRF for the period 26 November 1982 to 1 October 1983. The testing covered herein is for coarse Pittsburgh Seam coal in the 6-in (150 mm) and 12-in (300 mm) pipelines, at velocities ranging from 5 to 18 ft/s (1.5 to 5.5 m/s), and at concentrations by weight ranging from 15 to 55 pet. Particle size distribution samples were taken systematically throughout the testing.

Jan 1, 1985

By Edward J. Kansa

In a Bureau of Mines study, unsteady, spherically symmetric, one-dimensional, compressible-flow (finite sound speed) equations were solved numerically for a spherical deflagration propagating concentrically in a spherical vessel with Mach numbers ranging from 0.2 to 0.7; trajectory histories agree with the infinite-sound-speed theory developed by Perlee, Fuller, and Saul (PFS). A preliminary result of this study shows that flames propagating with speeds greater than 20 pct the speed of sound in the unburned gas mixture generate a complex history of aerodynamic waves distributed throughout the spherical vessel. Although the average pressure and flame radius agree with those predicted by the PFS models, the aerodynamic waves have a pronounced effect on the flame velocity, differing appreciably from that predicted by the PFS model.

Jan 1, 1976

By D. E. Ingersoll

This report describes the preparation characteristics of anthracite from the Mammoth and Holmes veins in Schuylkill County, Pa., as determined by the Federal Bureau of Mines laboratory separations at specific gravities of 1.50 to 1.90. The Holmes vein anthracite contains approximately 13 percent ash, and the Mammoth vein contains about 9 percent as fed to the breaker. Crushing Broken, Egg, and Stove sizes from each vein produces Pea-size anthracite of lower ash content than that contained in Buckwheat No.1 size and smaller. The Buck-wheat No.5 size has the highest ash content of all the sizes examined. Potential recovery from a mixture of the two veins as received at the breaker, separated at 1.90 specific gravity, is approximately 64 percent of the feed at 11.0 percent ash. The same materials separated at 1.80 specific gravity yield about 61 percent with an ash content of 10.1 percent. All rejects are from the Holmes vein, because the entire Mammoth material is less than 10.0 percent ash.

Jan 1, 1960

By Michael R. Grubbs

The Bureau of Mines is currently developing methods for reclaiming the metal and mineral values contained in unburned urban refuse. One important phase of this research deals with recovering Mastic from shredded refuse using in electrodynamic separation process. The results of this study have indicated that mixed plastic concentrates analyzing 99.4 percent plastic can be consistently recovered from the light material fraction of shredded refuse, leaving a mixed paper traction analyzing 99.9 percent paper. Recovery of the plastic exceeds 99 percent.

Jan 1, 1972

By Doerner H. A.

From thermodynamic calculations Maier predicted that zinc oxide and methane would react at specified temperatures substantially according to equation (1). (1.) ZnO + CH4 = Zn (gas) + CO + 2H2. Other reactions that may take place are (2.) CH4 = C + 2H2. (3.) ZnO + CO = Zn (gas) + CO2. (4.) ZnO + H2 = Zn (gas) + H2O. Maier predicted that 870°C would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C. Theoretical considerations indicate that reaction (1) is reversible: this is supported, but not proved, by experimental data. The other reactions are known to be reversible. At low temperatures reaction (2) requires a catalyst and it is slow below 1000°C. Reactions (3) and (4) are rapid, but the equilibrium constants are such that only small concentrations of CO2 or H2O can be produced below 1000°C. Maier calculated that CO2 should not exceed 0.5 per cent at 870°C., and the calculation for water vapor gives a still smaller order of magnitude.

Jan 1, 1931

By F. E. Joyce

The Bureau of Mines studied copper-nickel minerals (mainly sulfides) of the Duluth Gabbro Complex in north-eastern Minnesota to determine their response to selective high-temperature sulfatization techniques. The gabbro, containing 0.44 percent copper and 0.13 percent nickel, was ground to minus 325 mesh and sulfatized in a heated, rotating, stainless steel bench-scale retort. Tests demonstrated that over 95 percent of the copper and 80 percent of the nickel can be converted to water-soluble sulfates, depending upon the roasting conditions employed. Yield equations were developed using regression analysis for predicting the extraction of copper and nickel between the temperature limits of 520° to 670° C, the roasting time limits of 3 to 7 hours, and S02 limits of 10 to 40 percent in S02-air mixtures.

Jan 1, 1971

By R. V. Lundquist

The work described in this report, part of the Bureau of Mines long-range program to develop methods of utilizing submarginal domestic sources of aluminum, was undertaken to investigate the effects of iron in the lime soda sinter process, The approximate Fe2O3 content in a sinter for maximum alumina and soda recovery was 8 to 9 percent. Fe2O3 appears to inhibit gelation, and 15.5 percent Fe2O3 produces effects similar to those produced by 1 percent sucrose. In the lime soda sinter process, aluminum silicates are sintered with limestone and soda ash to yield dicalcium silicate and sodium aluminate. The sodium aluminate is extracted by leaching in caustic solution. The solution is purified by heating in an autoclave with lime to remove silica, and alumina trihydrate is precipitated with carbon dioxide. The reactions involved in sintering and leaching are complex. A number of studies by the Bureau of Mines4-9 and others1 indicate that the iron content of sinters influenced the recovery of alumina and soda and the gelation characteristics.

Jan 1, 1962

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page, Linda J. McWilliams, Gerald J. Joy, Steven E. Mischler, Jon C. Volkwein

The United States National Institute for Occupational Safety and Health, through an informal partnership with industry, labor, and the United States Mine Safety and Health Administration, has developed and tested a new instrument known as the Personal Dust Monitor (PDM). The new dust monitor is an integral part of the cap lamp that coal miners normally carry to work and provides continuous information about the concentration of respirable coal mine dust within the breathing zone of that individual. Previous laboratory testing demonstrated that there is a 95% con?dence that greater than 95% of individual PDM measurements fall within ±25% of reference measurements. The work presented in this paper focuses on the relationship between the PDM and respirable dust concentrations currently measured by a coal mine dust personal sampler unit utilizing a 10 mm Dorr Oliver nylon cyclone. The United Kingdom Mining Research Establishment instrument, used as the basis for coal mine respirable dust standards, had been designed speci?cally to match the United Kingdom British Medical Research Council (BMRC) criterion. The personal sampler is used with a 1.38 multiplier to convert readings to the BMRC criterion. A strati?ed random sampling design incorporating a proportionate allocation strategy was used to select a sample of mechanized mining units representative of all US underground coal mines. A sample of 180 mechanized mining units was chosen, representing approximately 20% of the mechanized mining units in production at the time the sample was selected. A total of 129 valid PDM/personal sampler dust sample sets were obtained. A weighted linear regression analysis of this data base shows that, in comparison with the personal sampler, the PDM requires a mass equivalency conversion multiplier of 1.05 [95% C.I. (1.03, 1.08)] when the small intercept term is removed from the analysis. Removal of the intercept term results in a personal sampler equivalent concentration increase of 2.9% at a PDM measurement of 2.0 mg m-3.

By W. H. Eddy

The Bureau of Mines made small-scale continuous tests and large-scale commercial plant tests of a calcareous fluorspar ore near Cave-In-Rock, Ill., to determine if the application of the lignin-fluoride process of fluorspar flotation would be industrially feasible for treatment of fluorspar ores, and also to compare the lignin-fluoride process with the quebracho process, which is the method currently used for concentrating calcareous fluorspar ores. The small-scale continuous tests yielded fluorspar concentrates analyzing 93.6 percent CaF2 with a recovery of 87.6 percent of the total fluorspar in the ore. In large-scale commercial plant tests, a fluorspar concentrate analyzing 93.3 percent CaF2 with a recovery of 78.0 percent was produced by the quebracho method. About 86.0 percent of the fluorspar was recovered in a metallurgical-grade fluorspar concentrate from the lignin-fluoride circuit which analyzed 89.9 percent CaF2? with a much simpler flowsheet than that in the current commercial application.

Jan 1, 1967

By Juel H. Stears

The bureau of Mines analyzed data from 47 coal mine roof-fall resupport accidents that occurred from 1966 through 1974 to identify critical hazards .and problems. These accidents resulted in 62 injuries or fatalities. It was concluded that the majority of the accidents might have been prevented by observance of recommended practices and use of available technology such as setting temporary supports, adequate roof testing, etc. Additional work is needed in the following problem areas where present technology is inadequate: (1) warning of impending roof falls shortly before they occur, (2) better methods of detecting unsafe roof and ribs, (3) providing access to and temporary support of high roofs for testing and bolting, (4) reducing the noise level of stopers, (7) developing temporary roof support; that have greater stability and can be remotely installed, and (6) reducing the number of roof falls through better permanent support.

Jan 1, 1976

By Thomas M. Barczak

This Bureau of Mines report describes research on developing technology to utilize shields as roof load monitors. Three-dimensional equations of static quilibrium are presented for a generic two-legged long-wall shield. The equations are presented in the most general form, assuming a force and moment vector at each reaction by rigid-body analysis of the shield mechanics. The resulting system of equations was found to be indeterminate to a very high degree. A three-dimensional solution to measurement of the resultant reaction on the canopy by the strata activity and shield response required the elimination of several forces or moments that were thought to be nonparticipating or to not significantly affect overall shield mechanics. Required measurements for solution of the equilibrium equations were leg, canopy capsule, and lemniscate link forces. Two-dimensional analysis, which considered forces acting only in the roof-to-floor and face-to-waste plane, was also provided by reduction of the three-dimensional equations~

Jan 1, 1987

By McHenry Mosier

This is the fourth progress report in the series on the use of detachable rock-drill bits in the metal mines of the United States. It contains comparative statistics and costs or drilling at eight mines not reviewed in previous reports, comparison of the use of detachable bits at small mines and large mines, a discussion on the life of drill rods, and general conclusions derived from an analysis of the rock-drilling practice at all the mines investigated on this survey. This paper completes the descriptions of operating practice in rock drilling at individual mines. Data on drilling practices at 28 mines are given in appendices I and II and drilling costs are shown in appendix III. Research in the fundamentals of rock drilling, including the use of detachable bits, has been undertaken by the Bureau of Mines in its testing adit at Mount Weather, Va. Reports on the progress off this investigation will be issued when results warrant their publication.

Jan 1, 1937

By John H. Soule

The Royal John mine was examined in November 1942 by a mining engineer of the Bureau of Mines, who proposed development of the Royal John and other properties in the area. Geologists of the U. S. Geological Survey studied the area in 1943 and 1944 and made definite recommendations. Also, in 1943 the Peru Miring Co. mapped the Royal John and did considerable diamond drilling. The Bureau of Mines started the Royal John portion of a project pertaining to the general district in April 1944. This project was completed in Juno 1945. The work, consisting of diamond drilling, was supervised by Robert O. Hill, mining engineer, and the results were published in Report of investigations 3904, Exploration of Grey Eagle, Grandview and Royal John Claims, Grant County, N. WIC. In 1947 and 1948 the Royal John was re-examined by a Bureau engineer, and additional development to increase the reserves of low-grade lead-zinc ore was proposed. This project was started in August 1948 and completed in Juno 1949.

Jan 1, 1950

By Jürgen F. PH. D. Brune, Alex C. Smith, Michael A. Trevits

Underground coal mine fires in the United States continue to present a significant hazard to the safety and health of mine workers. The leading causes of mine fires include flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion The National Institute for Occupational Safety and Health (NIOSH) is conducting an in-depth program of research to address mine fire prevention, early and reliable fire detection and mine fire suppression and control technologies. One segment of the research portfolio is focused on remote methods for addressing coal mine fires. This research is important because remote methods represent the primary means of fighting a mine fire when conditions are too dangerous to fight the fire directly underground. Technologies under investigation include remote methods for installing ventilation control devices (mine fire seals) and remote methods for suppressing the fire using, the injection of inert gas, gas-enhanced foam and jet engine exhaust gases into the fire zone. This paper presents a summary of remote mine firefighting technologies used in the U.S. and the results of completed NIOSH research.

By R. R. Wells, K. C. Vincent, A. O. Ipsen

"INTRODUCTION The Philipsburg Mining District, Granite County, Mont., has been the largest producing area for battery-grade manganese (70 percent MnO2) in the United States since the First World War. Two companies, the Trout Mining Division of the American. Machine & Meals Co., and the Moorlight Mining Co., have intermittently mined and milled 120 to 250 tons of 25-percent manganese ore per day for the production of concentrates of this grade.Investigation of the district by engineers of the Federal Geological Survey and Bureau of Mines indicated that further exploration and develop¬ment would make available additional oxide and carbonate manganese ores for milling and production of metallurgical-grade manganese. If the battery-grade producers converted their plants to the production of metallurgical-grade concentrates, their production also could be increased through greater recoveries.Until February 1, 1944, the Metals Reserve Company, through its agent, the Sunshine Mining Co., purchased milling-grade manganese oxide and carbonate are for stock-piling at Philipsburg. After that time, only carbonate ore was purchased. Based upon the assumption that the stock pile was a true cross-section sample of the producing area, metallurgical studies were made on representative samples from the Metals Reserve stock piles. Testing also was conducted on two other samples of Philipsburg oxide manganese ore obtained by engineers of the Bureau of Mines from the Little Dandy claim of the Donlan group and from the Marie mine. All ore samples tested were found to be amenable to concentration by ore-dressing methods for the production of concentrates that when sintered met Metals Reserve Company specifications for metallurgical-grade manganese."

Nov 1, 1947