Search Documents

By Fred N. Kissell, Andrew B. Cecala

In This Chapter [Where methane is emitted at longwall faces Where methane accumulates at longwall faces Using the modified shearer-clearer to eliminate ventilation eddy zones Using a walkway curtain to reduce methane buildup during the headgate cutout Control of frictional ignitions and The best location for the methane monitor] The methane released along a longwall face represents only 10%–20% of the total methane emitted from the entire longwall panel. Nevertheless, in very gassy coal seams, this methane released at the face can pose a problem because the shearer is a ready ignition source. Preventing methane ignitions at longwall faces requires four actions. The first is to provide better ventilation around the shearer to eliminate the ventilation eddy zones at the drums where methane builds up. These eddy zones are eliminated by mounting additional water sprays on the shearer to direct air into them. The second action to prevent methane ignitions is to install a water spray behind each cutter bit and regularly replace worn bits. Water sprays behind each cutter bit act to quench the hot metal streak that follows a worn bit when it strikes rock. The third is to ensure that no ventilation eddy zones are inadvertently created by poor placement of water sprays. The fourth is to ensure that the methane monitor on the shearer is in the best location to detect methane accumulations. ADDRESSING METHANE ACCUMULATIONS AT LONGWALL FACES3 Cecala et al. [1985a, 1989] and Denk and Wirth [1991] studied methane emission and ventilation patterns at longwall faces to find where methane accumulations are most likely. Although not always the case, the major source of methane at longwall faces is usually the breakage of coal by the shearer. Stress-related fracturing of the coal seam at the face, called bumps or bounces, can cause the release of additional gas (Figure 4–1).

Jan 6, 2006

By W. D. Striffler

Land disturbed by surface mining in Colorado and other western states has increased substantially over the past several years and is likely to increase even more in the future. This study was initiated to provide basic information on hydrologic and erosional characteristics of regraded coal spoils in Colorado as an aid for planning future reclamation activities. Eleven of twenty-one surface mines licensed in Colorado were sampled during the summer of 1980 and 1981. Mines not sampled included mines which had not progressed to the point that reclamation had begun, and mines where operators denied permission to sample. All coal regions were sampled with the exception of the San Juan Coal Field. Physical and hydrologic characteristics of regraded coal spoils in Colorado were determined using standard field and laboratory procedures. Field sampling included characterization of sites (slope, vegetation density, proportion of surface rock, bare soil, etc.) and infiltration measurements using a l-meter square drop former raining on a 1/2 square meter rectangular plot frame. Core samples collected in the field were analyzed for saturated hydraulic conductivity, bulk density, organic matter, moisture retention and texture. The erosion potential of each site was determined using the Universal Soil Loss Equation (USLE). Results of the sampling indicate that infiltration rates vary widely both within and between sites. However, definite trends with respect to coal fields are apparent. For example, the Green River (Yampa) coal region had a wide range of sampled infiltration rates (1.2 to 5.1 cm/hr). However, most of the sites clustered towards the low end of the range. The North Park (Marr Strip) also was rated at the low end of the infiltration range (2.0 to 3.0 cm/hr). Average infiltration rates for the Canon City and Uinta Coal Regions were at the high end of the range (4.9 to 5.5 cm/hr). Multiple correlation analysis of infiltration rates vs. site characteristics showed that infiltration rates were most closely correlated with the depth of wetting, the amount of mulch cover, and site slope. The depth of wetting was highly correlated with the depth of the topsoil and the bulk density of the spoil. In general, the topsoil at all sites appeared to be highly permeable to water intake but once saturated, subsequent infiltration depended upon characteristics of the underlying spoil. Vegetation cover affected infiltration on individual mine sites but was not as pronounced as topsoil characteristics or mulch. Erodibility of topsoil and spoils, as determined by Wischmeier's "K" factor, ranged from 1.34 to 0.56 tonnes/ha. (topsoil) and 1.25 to 0.66 tonnes/ha. (spoils). Definite trends in erodibility are evident. The Green River (Yampa) Coal Region displayed consistently higher erodibilities (1.34 to 0.75 tonnes/ha.) than other coal fields (0.72 to 0.56 tonnes/ha). Lowest erodibilities were observed in the Uinta, North Park, and Raton Mesa Coal Regions (0.56 to 0.62 tonnes/ha). Erodibilities of underlying spoils showed similar trends as the topsoils. Erosion potential (the product of soil erodibility and rainfall erosivity) was detennined using calculated ?K? factors and rainfall erosivities (R) taken from Clyde (1976). Results show that the Delagua coal field, Raton Mesa Coal Region had the greatest erosion potential due to the high rainfall energies in the region, while the North Park and Uinta Coal Regions had the lowest potential erosion.

Jan 1, 1981

By Richard A. Winters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 34,000 acres of the 58,040-acre Little Jacks Creek Wilderness Study Area (ID-111-6) in order to evaluate the mineralized resources. The study area is located in Owyhee County, 10, about 21 miles southwest from Bruneau. No mining districts are in the study area, nor were any mines or claims recorded or found. The northern half of the area was covered by oil and gas lease applications; all were cancelled prior to 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Little Jacks Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By G. F. Kuncir

The analysis described herein evaluates the Bureau of Mines Program for Advancing Mining Technology - Oil Shale in terms of the economic benefits which may be derived for the Nation as a result of its successful research and development efforts. On the basis of postulated oil shale production scenarios, benefit-cost ratio indicators are computed for the program elements as they apply to surface, underground, and modified in situ oil shale mining systems. Eight value indicators are used to measure the Program's beneficial impact on the future oil shale industry in relation to planned research and development costs. These are: capital cost savings, operating cost savings, labor savings environmental quality maintenance cost reduction, reduction in production costs, byproduct production benefits, total production benefits, and additions to recoverable reserves. Program costs are aggregated from 1974 through 1987 and major benefits are accrued from 1982 through 2040. Both cost and benefit streams are discounted to mid-1975 present value.

Jan 1, 1977

By W. W. Weller

Thermodynamic values for scandium and its compounds are very sparse. This is evident upon examination of any of the commonly used compilations of thermodynamic data. For example, National Bureau of Standards Circular 5004 lists only four heat of formation values, two free energy of formation values, and four heat-capacity values for scandium compounds. The entropy of crystalline scandium is one of the most fundamental values that has been lacking. This Bureau of Mines paper reports heat-capacity data for scandium metal in the temperature range from 50° to 298° K., together with the entropy value at 298.15° K. derived from these data through application of the third law of thermodynamics.

Jan 1, 1962

By G. R. Hopkins

According to reports received by the Bureau of Mines, Department of Commerce, as of January 1, 1929 there were 413 completed refineries in the United States, with a total daily crude-oil capacity of 3,509,540 barrels. In addition, 14 refineries, with a potential capacity of 99,000 barrels, were being constructed. Of the completed refineries, 341, with a capacity of 3,325,890 barrels, or 95 per cent of the total capacity, were in operation; and 72, with a capacity of 183,650 barrels, or 5 per cent of the total, were shut down. The improved condition of the refining industry in 1928 was indicated in several ways; namely, in an increase in the total capacity of the completed plants, in the opening up of a few plants which were shut down during 1927, in a decrease in the number of plants dismantled, and in an increase in the number of plants under construction. The majority of the refiners have followed a steady expansion program commensurate in most cases with the increase in demand for petroleum products. Obsolete equipment has been dismantled and modern equipment has been installed, with the net result that the total capacity of the completed refineries in the United States has shown a steady increase since January 1, 1918, the date of the first Bureau of Mines survey. Between January 1, 1928, and January 1, 1929, the number of completed plants fell from 423 to 413, but their total capacity increase 259,160 barrels, or 8 per cent. This compares with an increase in runs to stills of domestic and foreign crude petroleum of 10 per cent, and of domestic crude alone of 7 per cent.

Jan 1, 1929

By A. Soderberg

This paper describing the mining practice at the Utah Copper Co., Bingham Canyon, Utah, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Utah Copper Co. operates the low-grade open-out copper mine at Bingham Canyon, Utah, which is 30 miles in a southwesterly direction from Salt Lake City. In addition to the mine the company operates two flotation concentrators, the Magma plant and the Arthur plant, which have a combined capacity at maximum metallurgical efficiency of 60,000 tons daily. The concentrators are at Magna, about 18 miles from the mine. The company operates its own standard-gage railway, known as the Bingham and Garfield Railway, between the mine and the mills (fig. 1). Concentrates are smelted at the Garfield smelter of the American Smelting and Refining Co., situated 4 miles from the mills.

Jan 1, 1930

By Fred N. Kissell

In This Chapter [Ventilation and methane sampling guidelines for conventional shafts Dealing with restricted spaces where methane can accumulate Ventilation and methane sampling at raise bore drills and Filling shafts at closed coal mines] It is not unusual to encounter methane gas during shaft excavation or shaft-filling operations. Shafts into coalbeds usually produce the most methane, so the information in this chapter applies primarily to shafts at coal mines. Nevertheless, much of the information is relevant for noncoal mines that have methane in the mine or in the overlying strata. METHANE IN SHAFTS EXCAVATED BY CONVENTIONAL MEANS (DRILL, BLAST, MUCK) [ ] Ventilation. Shafts excavated by conventional means are ventilated with a fan on the surface connected to ductwork that extends down into the shaft (Figure 9–1). Shafts into coalbeds should have ventilation systems designed to handle the higher gas flows to be expected as the shaft excavation passes through any over-lying gas-containing strata and nears the coal-bed to be mined. Following are some simple ventilation guidelines for the minimum amount of air required and the selection of the ventilation duct: • Provide enough air to meet the mini-mum OSHA tunnel requirement of 30 ft/min air velocity in the open shaft, as specified in 29 CFR2 1926.800(k)(3). For example, a 20-ft-diam shaft having

Jan 6, 2006

By R. H. Grau, S. B. Robertson, R. B. Krog

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. Large-opening mine ventilation is unique for the following reasons: (1) it is challenging to keep airflow velocities high enough to effectively remove or dilute airborne contaminants, (2) large air volumes can be moved through the mines with little static pressure drop, and (3) stoppings to direct ventilation airflows are costly to construct and maintain. The research results suggest that by incorporating ventilation planning into the mine planning process, using propeller fans, developing new stopping materials and construction methods, and using long pillars to eliminate crosscuts where possible, the ventilation of large-opening mines can be significantly improved. The ventilation improvements created by incorporating these various techniques into the ventilation plan will help reduce the exposure of mine workers to airborne contaminants in underground large-opening mines.

By Douglas F. Scott

In 1981 the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the Pyramid RARE II area (No. 5023) covering 23,500 acres (9,500 ha) of E1 Dorado National Forest and 7,900 acres (3,200 ha) of the Lake Tahoe Basin Management Unit (fig. 1). The Bureau of Mines investigation did not reveal mineral deposits in the area. Samples taken from silicified and limonite-stained metasedimentary rocks and aplite dikes were void of precious or base metals or uranium. Placer samples from stream gravels contained no gold values. Molybdenite occurs in quartz stringers within quartz monzonite near Grass Lake, adjacent to the area; no extension; were found in the area.

Jan 1, 1982

By Timothy W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (?water box?) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 percent reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2010

By R. Farrar

The survey work on protective canopy design was conducted in a 2-month period commencing November 15, 1973. The reported re¬sults under this contract are intended to provide guidance to coal mine operators in complying with federal regulations pertaining to incorporation of protective canopies on underground coal mine electric face equipment. All coal mine electric face equipment manufacturers and 11 coal mines were visited in the course of conducting this survey. Canopy designs currently being manufactured and those now being used underground were examined and discussed with manufacturers, mine operators, machine operators, and safety committeemen. The general objective was to find out what kind of canopies are now being made and used underground, what the operational problems are, and what can be done to secure improvements. Specifically, the survey scope was as follows: a. Survey all electric face equipment manufacturers. b. Survey 10 coal mines (seam height 60 inches and greater). c. Identify current production canopy configurations and minimum mine entry dimensions for each model and type of electric face equipment. d. Assess in-mine operation of canopies developed by manufacturers and/or coal companies. e. Specify optimal canopy configuration and minimum mine entry dimensions for each type and model of electric face equipment.

Jan 1, 1974

By K. T. Menzies

Over 1500 literature citations related to diesel exhaust sampling and analysis were obtained as a result of both computer and manual searches of nine data bases. Abstracts and hard copies of relevant citations were reviewed and those considered appropriate for evaluation were included in a bibliography. Based on the literature collected, available sampling and analysis methods for the following diesel exhaust contaminants were evaluated: CO, CO2, NO, NO2, Hydrocarbons, Particulates, PNA, S04, Oxygenates Emphasis was given to both laboratory and field methods for these species. Methods were evaluated on the basis of sensitivity, selectivity, accuracy and reliability and a selected list of preferred methods was developed for each compound/ class. The selected methods were additionally evaluated through communication with current investigators. Sampling and analysis methods for all compounds except CO and CO2 were observed to have some unreliability. Recommendations were made for future research to develop, improve, and validate methods.

Jan 1, 1979

By Deno M. Pappas

This report presents results of a U.S. Bureau of Mines study of longwall gob material. The objective of this work was to determine material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining, Photographs of actual mine gob were digitized to obtain approximate particle size gradations of gob material. The gradation curve was shifted down to a laboratory scale, and 20 uniaxial compression tests were conducted. Varying the maximum particle size was not found to affect the stress-strain behavior, but changing the gradation appeared to influence the stress-strain behavior. The stress-strain relationship of the simulated gob material was nonlinear, the stress-secant-modulus relationship was approximately linear, and the stress-tangent-modulus relationship was approximately a second-order polynomial function. Equations were generated from these curves, providing numerical modelers with a means to estimate gob moduli based on the stress level. In addition, the experimental data were statistically evaluated using multiple regression analyses, producing a series of equations to predict the secant and tangent moduli from the given stress level, bulking factor, rock strength, and thickness-to-width shape ratio of the particles.

Jan 1, 2010

All of the coal resource in North Dakota is lignite. The lignite fields of North Dakota cover approximately 40 percent of the total area of the state, with reserves estimated to be 9.8 billion tons, two percent of the U.S. base. The first commercial coal mine in North Dakota opened in Morton County in 1873. As the railroads crossed the plains, the demand for coal increased. Coal for fuel was supplied by the state's underground mines. By 1884, North Dakota's lignite production had reached 35,000 tons. North Dakota was among the fist states to shift from underground to large-scale commercial surface coal mining. By 1927,40 percent of the total production was by surface mining, compared to 2 percent for the nation as a whole. By 1959,86 percent of the total production was by surface mining, while the national average was 22 percent. Since 1966, surface mining has been the exclusive coal production method in North Dakota. North Dakota's regulatory program received conditional approval December 15, 1980. Following approval of amendments to the program, it received full approval February 18, 1986. The Abandoned Mine Lands Program was approved December 23,1981.

Jan 1, 1992

1. Domestic Production and Use: Twelve companies operated 31 primary aluminum reduction plants, three firms accounting for 66% of production. Washington, Oregon, and Montana accounted for 32% of the total production; Gulf Coast States, 25%; Northern States, 29%; and other Southern States, 14%. Output of primary metal in 1973 was valued at $2.2 billion. About 80% of the secondary recovery was from new aluminum base scrap and 20% was from old scrap. Aluminum consumption by 25,000 firms was centered in the East Central United States. Of aluminum consuming industries in 1972, building accounted for 28%; transportation 19%; electrical, 13%; packaging, 16%; and consumer durab1es, 10%.

Jan 1, 1974

By P. -É. Boileau, VibRG, S. Grenier, M. Smets, T. Eger, J. Stevenson

Load-haul dump vehicles (LHDs) are used to move waste rock and ore in underground mining operations. The LHD is designed for bi-directional operation and the driver sits sideways to the direction of travel. LHD operators have higher reports of low back pain and neck discomfort than other mobile equipment operators who do not sit sideways in the vehicle, but are exposed to whole-body vibration (WBV)1. Exposure to WBV is linked with reports of lower-back pain, neck problems and spinal degeneration2,3. Static sitting postures, sitting with the neck and back twisted, and sitting with the back in an unsupported posture are also linked with an increased risk of developing back pain4. The objective of this study was to determine typical vibration exposure levels and driving postures for LHD operators. Methods Whole-body vibration exposure was measured at the seat-pan, in accordance with the ISO 2631-1 standard5, on seven LHD vehicles with a 10 yard bucket haulage capacity. Vibration data were recorded with a Biometrics™ DataLog II (P3X8) and stored on a 128 Mb Simpletech™ multimedia card. Comparisons were made to the ISO 2631-1 Health Guidance Caution Zone (HGCZ) in order to determine potential injury risk. Operator posture was monitored with three digital video cameras which were secured inside each operator’s cab to the top left corner, top right corner and back right corner. Reflective tape was placed on each driver’s shoulders, head, and back in several locations and in several locations on the vehicle seat in order to aid in posture coding. Posture coding was performed with 3DMatch v4.50 multiple video view analysis feature. Vibration measurement and posture recording occurred simultaneously for 60 minutes while the LHD operator performed typical duties. Results and Discussion Results indicate LHD operators may be exposed to whole-body vibration levels putting them at risk for injury (Table 1). According to ISO 2631-1 the frequency weighted acceleration values corresponding to the lower and upper limits of the HGCZ (for an 8 hr exposure duration) are 0.45 and 0.90 m/s2 respectively5. Six of the seven vehicles showed exposure levels within the HGCZ defined for 8 hours. Preliminary video analysis indicated LHD operators were exposed to potentially harmful levels of WBV while adopting asymmetric postures (Table 2). For example, one LHD operator (Figure 1) worked with his neck twisted greater than 40 degrees for 93 % of a 60 minute work cycle. According to the Swedish National Work Injury Criteria, neck rotation should be less than 15 degrees if the motion is required for greater than 80% of the work time6. Results of this study highlight the need to further examine the contribution of non-neutral working postures and

Jan 6, 2006

By Michael J. Beus, Stephen Iverson

BACKGROUND A mine shaft is the lifeline to underground mines. Mine operators depend on safe, uninterrupted, and efficient movement of workers and materials. The shaft and hoisting system provides access to the network of openings used to recover the underground resource, provides vertical transport of miners and materials, and serves as an escapeway in case of an emergency. Accidents involving hoisting can be catastrophic. Such was the case in 1973 at the Markham Colliery in Derbyshire, UK when the conveyance overwound and fell to the shaft bottom, resulting in 17 deaths. Hoist and elevator machinery must meet the requirements specified in the Code of Federal Regulations (CFR), Parts 57 and 75. According to the Mine Safety and Health Administration (MSHA) data, many shaft-related accidents in the United States are associated with the hoisting cycle. MSHA statistics show that there were about 1500 shaft- related accidents in the 5-year period between 1992-1996. Most of these accidents resulted from the action, motion, or failure of the hoisting equipment or mechanism and involved movement of the conveyance which includes cages, skips, ore buckets, and elevators. A hoisting hazard may be characterized as an "unsafe hoist operating condition caused by insufficient or inaccurate information available to the hoist operator" (authors' quote). Earlier investigators have defined safety features and operating and maintenance standards for hoists, and reported on monitoring and control systems and sensors for hoists and conveyances [Farley, 1983; Ward, 19931. However, despite the considerable technological progress and hoisting control improvements in recent years, safety- related issues that require further investigation still remain. The hoist operator must constantly be aware of two important hoist-operating conditions: the position of the conveyance and the tension in the hoist rope. If this information is not available or is inaccurate, the hoist becomes unsafe. Current technology provides this information indirectly from sensors and indicators in the hoist room. However, unlike a building elevator hoistway, mine shaft hoistway problems often include: 1. poor ground conditions and excessive shaft wall and guide displacement; 2. rock bursts in deep mines (resulting in large rock movements and fragments blocking the hoist way); 3. water, ice, and salt buildup (impeding the smooth flow of the conveyance); 4. severe vibration from hoisting (resulting in loose guide support brackets, broken welds, or other alignment and conveyance mechanism malfunctions). The second issue relates to dynamic rope loads applied during normal winding, particularly during loading, acceleration, and stopping. Safety factors on wire rope are based on static load. They are artificially high to account for all cases of dynamic loads, even though the total load history on the rope (static and dynamic) during service is unknown. Therefore the tension, and thus the compliance with wire rope load safety factors, is unknown to the hoistman.

By Avery H. Reed

RECORD production of cement, clays, salt, sand and gravel, and stone highlighted the mineral industry of the State in 1956. Coal and iron-ore production declined owing to increased imports of foreign iron ore and decreased demand for metallurgical coke. Alabama ranked second in production of bauxite and of native asphalt, and third in output of iron ore. New developments in the State included the Citronelle oilfield and its 97 wells, which more than doubled the total production of petroleum compared with 1955. There is no question about the impetus that field has given to the oil and gas industry in Alabama, now 13 years old. The State's 4 oilfields are in southwest Alabama and its 1 gasfield is in Marion County, in the Warrior coal basin.

Jan 1, 1958

In the USA, the National Institute for Occupational Safety and Health (NIOSH) does a lot of work and has provided news of interesting new developments. Marcia L. Harris describes an ?Explosibility Meter: ?In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. Federal [US] regulations require 65% and 80% incombustible content in samples taken in intake airways and return airways, respectively, assuming a nominal coal dust size of 20% minus 200 mesh. The Coal Dust Explosibility Meter (CDEM), a hand-held instrument developed by NIOSH uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture.? The CDEM is now commercially available. It provides real-time results during rock dust surveys instead of waiting weeks for laboratory results1. ?With real-time results, the potential for a disaster can be mitigated immediately. The CDEM displays the percent incombustible content as well as a colour indicating the relative explosibility of the coal and rock dust mixture. A red read-out indicates that more incombustible material is required to inert the coal and rock dust sample, while a green read-out indicates that the dust sample is sufficiently inert. When the mixture is marginally explosible, a yellow read-out is indicated. The red-yellow-green output depends upon the particle size distribution of the rock and coal dust mixture with the finer size fraction being more explosible.?

Jan 1, 2008