Search Documents

By P J. Dailey, S L. Burchell, R F. Chiappetta

High-speed motion picture photography and its application to the mining, quarry, construction, and explosive industries has proven to be a valuable diagnostic tool. The techniques developed allow one to evaluate blasting performance, compare explosive efficiencies in relation to burden velocity, and estimate optimum delay times to provide adequate forward relief.

Jan 1, 1983

By J. Silva, M. Kotraba, F. Pontanilla

Blasting is the application of highly complex science that, in some cases, could be viewed as an art. Many variables are involved in a blast, including geology, pattern design, timing and firing sequence, and explosives selection. Assuming that better results can be achieved by only increasing the powder factor is inaccurate. The Drill-to-Mill (D2M) concept has been in the mining industry for over two decades. The D2M approach is commonly viewed in an oversimplified manner, assuming that by simply increasing drilling and the amount of explosives used (both of which add operational costs), the downstream value will be created. An optimized D2M initiative should combine the smart application of explosives at the beginning of the mining process, matching the dynamic properties of the rock to the explosive selected to improve the efficiency of the energy created by the explosive to the rock mass being blasted, and to bring benefits to the mining operation across the entire mining and processing value-chain. This paper reviews the principles behind matching the shock impedance of the rock and the explosive and compares the traditional use of explosives versus the smart application for two hypothetical blasts.

Jan 1, 2024

By Blair Jackson, Tjaart Louw

Martha Mine, owned by Newmont Mining, Australia appointed Macmahon Contractors (NZ) Ltd as the mining contractor to drill, blast, and crush and convey ore for processing, followed by construction of a tails dam facility from the waste material. The open pit is located 140km(90miles) south east of Auckland, New Zealand in the middle of the township of Waihi (the main street of the town with a population of 3,500 is 90m from the perimeter of the open pit mine). Mining must proceed at 325,000m3 (of which involves blasting approximately 11,000 holes per month, in order to ensure continued ore supply.

Jan 1, 2003

By Scott G. Giltner, Terry Millar, Ben Bringhurst

"Kennecott Utah Copper (KUC) Smelter scheduled a rebuild of their flash smelting furnace forSeptember, 2014. KUC’s goal in this project was to reduce the rebuild time from 65 to 55 days by using explosives to break the matte and brick layers of the uptake shaft and hearth sections of the furnace. Previous rebuilds had employed the slower technique of mechanical breakers to remove the matte and brick layers which took 22 days. KUC has many years of experience in removing slag from the uptake shaft, but they had never used explosives to remove the hearth. As far as KUC was aware, no other smelter operation had attempted a hearth removal in this way."

Jan 1, 2016

By Richard J. Mainiero, James Q. Wheeler, Lewis H. Kopera, Yael Miron, Solin S. W Kwak

The research reported here was part of an effort to evaluate the safety of a process to recover TNT from MK-9 depth bombs by the autoclave meltout process. In this process the depth bombs are heated to 121oC so that the TNT will melt and run into a vat. Unfortunately, asphalt lining the inside surface of the bomb also melts and flows out with the TNT. Prior to this study, it was not known what effect the asphalt contamination and the higher than normal process temperatures (121oC) would have on the sensitivity of the TNT.

Jan 1, 1996

By Daodu Opeyemi

This paper describes several damages of blasting operations on some case studies, analyzes causative factors, and emphasizes preventive measures. Due to several complaints from some host mining communities as a result of blasting operations; two quarries from Nigeria suburbs were visited for study. The blasting design parameters in the mining companies were examined. Also, the history and existing conclusion of the neighboring buildings were studied using structured questionnaire, personal contact and visual examination. From the study carried out, it was discovered that varying negative environmental and socio economic problems resulted from the effects of vibration and flyrock on the nearby agro mining communities. The consequences are not limited to distortion of landscape but also include extinction of some animals, poor agricultural productivity; such as damages to economic trees and reduction in the yield of crops, health problems as a result of shock resulting to psychological disturbances, communal conflicts, blast induced cracks of structures and sometimes total collapse of host agro mining buildings, thus indicating that most mines did not comply with the safety concept of the existing environmental laws and regulations. Based on the results of the study it was recommended that proper blast design of quarries/mines should be conducted and the compulsory use of seismograph will be crucial in developing predictions. Environmental impact assessment should always be conducted before, during and after each blasting operation. Other possible control of vibration, flyrock and airblast, are also discussed in the paper

Jan 1, 2009

By Vitor Fonseca de Barcelos, Jair Carlos Koppe

Our society is experiencing a digital revolution. Technology is demonstrating its significant potential for mining industry. In this paper are presented the measured and estimated impacts of applying new technologies on blasting operations in a copper mine.

Feb 1, 2020

By Abdulkadir Karadogan, Zikri Keti, Umit Ozer, Mehmet Aksoy, Ulku Kalayci

This paper presents an investigation about how the motions of blast induced vibration waves were affected by the presence of the fault planes. This study was carried out at Espey Open- Pit Boron (Colemanite) Mine in Turkey. Within the scope of the study, ground vibration components were measured for 8 shots using 9 vibration monitors, considering the direction of the fault. Measurement stations were located around the fault line that intersects the open-pit mine in the north-south direction and on different benches along the fault plane. Then, the data of the vibration components obtained from the 77 recorded events were analyzed and the results were presented.

Jan 1, 2012

By Brian Stump, Chris Hayward

Blasting operations at one copper mine are studied in detail to examine the relation between blast design parameters and near-shot, in-mine, and regional seismic and acoustic observations. Five observational experiments, namely collection of blast design data, near source recordings, GPS synchronized video, near mine recordings and distant regional observations were performed during one week in August. A variety of seismic and infrasound instruments were installed near the shot, on the perimeter of the open pit mine, and at several locations up to 500 km distant. Time tagged video recordings were taken of several shots. Three shots were used in the preliminary analysis, a 350,000 lb pattern with long delays, a 60,000 lb pattern with short delays, and a 256,000 lb pattern with short delays. Maximum peak-to-peak amplitudes of the seismic signals in the mine are not a simple function of the total size of the shot, but are related to the pattern timing. Peak pressures have a less clear relation to peak pressure but match the relative amplitudes of spectra modeled from the pattern design. The predicted spectrum based upon a simple impulse model fits the observed spectrum for ground acceleration measured near the pattern and explains why in this case a pattern of 60,000 lb results in the same seismic disturbance as the 350,000 lb pattern.

Jan 1, 2002

By C Jamie Kridler

"An increased concern for pit safety and more stringent, highwall requirements for augermining of final cuts has led to a new emphasis on wall control for a Central Pennsylvaniacoal operator. Over the course of two and one half years and several locations, fieldpersonnel developed a very practical yet very effective system for maintaining safehighwalls. This involved the use of the blast design to: l) shape the highwalls 2) create andprotect a system of benching 3) pre_split large diameter holes using suspended ANFOcharges."

Jan 1, 1993

By T. G. Sitharam, P. B. Choudhury

Prediction of ground vibration (peak particle velocity, PPV) and frequency is an important task in geoscience. Till date, many empirical equations are derived from conducting trial blasts in the mines, to arrive at attenuation predictors. These predictors are usually site dependant and hold good for one particular type of rock/strata. These predictors cannot be used for geologically different rocks/strata. This paper presents the application of support vector machine (SVM) model, for predicting blast induced ground vibration and frequency, using a one comprehensive model for three different types of rock. Inputs to the SVM model formulation involve twenty one parameters consisting of geotechnical properties of the rock mass, blast design geometry and explosive properties, and the output of the formulated model is peak particle velocity and its associated frequency. The data has been acquired from eight limestone mine, five coal mine and two manganese mines. The comprehensive SVM model is formulated using 400 datasets and tested with 143 datasets. The performance indicators to the model not only justify its formulation but also the advantages it has over site specific predictor models. The SVM model not only predicts PPV, with higher correlation coefficients as compared to predictor equations, but also the associated frequency.

Jan 1, 2010

By Deepesh Yadav, B. S. Choudhary

Underwater drilling and blasting is conducted for deepening of sea channels for port berths, lake or reservoirs for water supply etc. so that rock dredging becomes easier. During this process there are several associated unwanted effects having potential to cause damage to surrounding structures and the environment, flora and fauna. Though all these ill effects can’t be completely eliminated but adopting controlled blasting techniques can minimize these to tolerable levels. It is recognized that ground vibrations resulting from rock blasting below water near dam may endanger the safety of earthen dams. Therefore, controlled blasting technique was used to ensure the safety of dam and its efficacy was established by monitoring of blast vibrations. The usage of small quantity of explosives confined in blast holes, non-electrical delay detonators and initiating each hole with a separate delay helped to minimize the ground vibration effects on surrounding structures.

Jan 1, 2018

By L C. Taylor

Very small scale testing has been shown to be able to predict quite accurately, in many situations, the results of full scale testing. Small scale tests are more cost efficient, easily observed, and easily instrumented than full scale tests. Over the past 10 years small scale testing in the Dynamic Effects Laboratory at the University of Maryland has been used to successfully study the response of structures and soils to explosive detonation. Small scale testing has been successfully used to predict full scale results in underwater cratering and channeling, the loading (both pressures and impulse) on vehicles due to the detonation of buried charges, the positive effects of bottom shaping for military vehicles to reduce this loading, and the movement of obstacles underwater by explosive charges.

Jan 1, 2012

By Michael Wieland

The thrust of this report is to overcome some of the technical deficiency in the scientific methodology that correlates the work output during a charge explosion to the resulting toxic fumes. Thermodynamic work-principle models yield (undissipated) shock and heave results for shooting underwater and in rock stratum with related toxic fumes. Underwater circumstances yield reliable test data for the work process, though questionable or no fume results. Work-output measurements in rock shots remain difficult if not intractable, though some fume reports exist. Underground tests with thick-wall metal pipe bombs yield consistent toxic fumes trapped within the test chamber. The work output, rendered as fragment kinetic energy, can be inferred from the well-tested theory of R. W. Gurney, originally designed for military ordinance. Therefore a work-principle model for cylindrical pipe bombs was developed to predict fragmentation work output and reaction-zone fumes, permitting the double comparisons to reported and inferred results.

Jan 1, 2010

By Lon Santis

Although unproven, it is suspected that there have been eleven locations since 1988 where explosive generated carbon monoxide (CO) gas moved through the earth and accumulated in nearby underground enclosed spaces. This paper summarizes the incidents, which involved about 30 suspected or medically verified CO poisonings and 1 fatality. Ten incidents occurred in residences and one occurred in a manhole. Although practically nothing is known about the mechanism behind the suspected gas migration, review of the incidents and available information indicates there are certain warning signs and a successful remediation technique available. In each case, overburden heavily confined the explosive in the blasts, preventing release of explosive-generated gases to the atmosphere. All the blasts were in residential areas, and none were excavated immediately. Where the distance from the blast was recorded, 5 of the blasts were within 20 to 50 feet (ft) (6 to 15 meters [m]) of the underground enclosed spaces, 3 were 100 to 150 ft (30 to 46 m) away, and 1 was 400 to 500 ft (120 to 150 m) away. Investigators often identified suspected pathways from the blast site into the underground enclosed spaces. One technique appeared successful at quickly correcting an existing condition. This technique involved applying negative pressure to the earth and removing the CO from the ground surrounding the underground enclosed space.

Jan 1, 2001

By Joshua Calnan, Braden Lusk, Kyle Perry

This paper presents detailed information and data regarding the load transfer characteristics of Blast Resistant Glazing Systems utilizing two different thicknesses of polycarbonate. A series of triaxial load cells, along with surrogates of identical stiffness characteristics, were placed around the glazing perimeter to directly measure the load transferred to the support system from explosions of varying degrees. The blast loads were developed using an explosive driven shock tube administered by the University of Kentucky Explosives Research Team (UKERT) in Georgetown, KY. Results presented include distribution of loading, maximum load transferred to connections, blast pressure-time data, glazing system deflection-time data, and final performance results of each system. The two glazing systems respond differently to the applied blast loading. Differences and similarities in the load transfer characteristics are discussed. The experimental results are then compared to a commonly used blast resistant glazing system analysis software tool utilizing a Single Degree of Freedom (SDOF) method of analysis for each system. Preliminary results show that currently used models do not correspond well with experimental data.

Jan 1, 2014

By Robert Cefalo

Drill and Blast Engineer Abstract In 2019, the Bingham Canyon Mine, owned by Rio Tinto Kennecott Utah Copper Company, mined through the active underground that dewaters the pit. The active underground required the limitation of vibrations to avoid catastrophic damage or damage that would require work to the shotcrete and additional roof support. The surface design of the current sector next to and through portions of the active underground. The drill and blast group was required to test site law vibration parameters to ensure that vibration limitations were lower than limits set by the underground management team. Seismographs were used to validate the vibration prediction model and check performance of blast in areas of the underground. The bench conditions and limited pounds-per-delay created large obstacles for the blasting team, making it difficult for them to accurately load the pattern with the number of decks in the blast. Methods were used to improve the loading instructions and ensure that each hole achieved pound requirements based off of the distance to the underground that it was designed to protect. The project evolved from start to finish, and the process to estimate distances and loading improved to make the blast a more repeatable process for the size of the project.

By Pierre De Pasquale, Gilles Jauffret, Ricardo Chavez

"When blasting in quarries or mines, the main source of inconsistent results is directly related to thenon-homogeneous energy distribution through the rock-mass volume. This variation has differentorigins: drilling deviations, geometry differences from one borehole to another (burden, spacing ...),and inherent geological conditions."

Jan 1, 2016

By Steve Collinsworth

Sometimes, for those of us in the right place at the right time with the right product, necessity creates opportunity. Such is my case at a West Virginia coal mine where a mine manager was desperately seeking a way to eliminate coal damage on cast shots while maintaining cast percentage without the expensive process of secondary drilling. This paper will focus on how bottom hole air decking is solving the problem.

Jan 1, 2000

By Dr. Calvin J. Konya, Anthony Konya

Blast violence has always been a criteria that has been analyzed without a quantitative approach relying on opinions of those viewing the blast and oftentimes does not transfer between open-pit mines, quarries, and construction projects. Added to this confusion is that on many regulate projects, such as U.S. Army Corp of Engineers construction projects, the definition of "flyrock" or violence can vary, and contractors must be able to meet this requirement. This project analyzed hundreds of blasts from various construction projects to develop a new metric to determine blast violence - the Violence Factor. If a blast is fired using 1.25" (32 mm) diameter product and a 10-foot (3 m) bench, vertical uplift of 60 feet (18.3 m) would be considered extreme and violent by any professional in the industry. However, a 100-foot-high (30.5 m) bench using 12" (305 mm) bulk product, having a vertical displacement of 60 feet(18.3 m)might be considered typical or non-worrisome. This is where violence factor is beneficial as itprovides a system of scaling the violence of a blast based on the bench height to give manager a keyperformance indicator (KPI) which is easy to monitor and can provide a large amount of information onsite-specific design variables for their performance on blasting and the end-results of the blast. The Violence Factor of a blast is an integer which is scaled to determine how high vertical uplift of a blast is compared to the bench height. This project analyzed numerous blasts to determine what blast design variables contribute to violence. This violence has also been shown to occur when a non-optimal breakage mechanism, cratering, occurs and the design criteria that lead to this cratering. Finally, this paper will present typical results of various levels of violence including backbreak, fragmentation, and muckpile configuration.