Search Documents

By Donald A. Deardorff

The capacity of a helical pile can be determined analytically using the individual bearing or cylindrical shear methods which are dependent on soil strength parameters and helical bearing area. The torque correlation method is widely used in the helical industry to determine the capacity during installation by monitoring torque during the final seating of the helicals. This method has been shown to be a better predictor of strength than the individual bearing or cylindrical shear methods. To determine capacity using the torque correlation method, the final average installation torque (ft-lbs) is multiplied by an empirical torque correlation factor (Kt, ft-1). Kt values have been well documented for square bar shaft helical products and can vary from about 3 to 20 ft-1 depending on pile geometry and soil type. A default value of 10 ft-1 is generally used for all square shaft sizes and soil conditions. Less research has been done on determination of Kt for round pipe shaft helical products. Studies have indicated that factors which affect Kt include soil type/strength, number of helical plates, helix spacing, helix pitch, depth of embedment, downward pressure (crowd), shaft diameter (round pipe) and load application direction while other studies have discounted some of these factors as inconsequential. This paper reviews past research findings regarding Kt determination for square and round pipe shaft helical products and presents a case history of round shaft helical pile installations in Chicago clay which resulted in much lower than expected Kt values.

Jan 1, 2007

By Jon Huff, Jeffrey Donville, Hannah Iezzoni, Dan Stevenson

Occasionally, in the design of deep foundations for a structure, a single deep foundation element may be used to support a building column. The most common type of element used in such cases is a drilled shaft (also referred to as a drilled pier, caisson, or bored pile). However, as installation capabilities have improved, large diameter augercast piles are increasingly more common. While drilled shafts and augercast piles differ significantly in construction methods, in the eyes of the International Building Code (IBC), both are treated as cast-in-place deep foundations and must comply with many of the same code provisions. Deep foundations are required to be braced such that lateral stability is provided in all directions, however isolated, cast-in-place elements that have a diameter (D) of at least 2-feet and a length (L) not more than 12 times the diameter can be an exception. In response to the concerns raised by some member professionals, the Deep Foundations Institute’s (DFI) Augered Cast-in-Place Pile and Drilled Displacement Pile Committee took a closer look at the code and its applications, the historical development of the code language through the years and performed analytical modeling to evaluate the impact of this ratio on a pile’s stability. The question is whether the limiting ratio included in the IBC 2018 code provisions is justified, or whether different criteria should be used to determine when isolated deep foundation members are allowed.

Sep 8, 2021

By Nasr Sheta

"After Hurricane Sandy, the stability of an earth slope in the Atlantic Highlands, New Jersey in the United States was deteriorating due to slumping soils and erosion from flooding. A slope stability evaluation indicated the slope did not satisfy the requirements of the local building code. A triple-tier, pile-supported and mechanically stabilized earth wall was designed and constructed to stabilize the slope. The construction was planned from a 3-m-wide roadway and, because of rough terrain and limited work space at the site, a cast-in-place drilled-pile construction was deemed impractical due to slow pile production. An alternative procedure was utilized by pre-drilling holes, and installing precast tip-and-shaft-grouted (PCTSG) piles, which extended to competent soils to improve slope stability. A grade beam, connecting the PCTSG piles along with soldier beams and concrete lagging were used to form the lowest tier of the slope stabilization, while the middle and higher tiers were built as mechanically stabilized earth. The stability of the proposed stabilization was analyzed using 2-D non-linear finite elements. After construction, monitoring of the wall continued for about 8 months to check its performance, and indicated lateral and vertical wall movements were less than 25 mm and 6 mm, respectively, indicating effective slope stabilization.INTRODUCTIONStabilizing earth slopes using piles to connect near-surface unstable soils to underlying stable ground masses has been investigated by many researchers, who presented various approaches to evaluate the contribution of the pile system towards improving the stability of the slope. Some of these approaches consider the piles as structural elements receiving forces from the upper sliding ground mass and transmitting these forces to the underlying stable one. The force from the top sliding mass is applied at between one third and one half of the pile embedment into the top sliding mass, Anagnostopoulos et al. (1990), Fukuoka (1977) and Matsui et al. (1988). The point of application of the sliding force was explored based on successful case histories while addressing the safety factors for both geotechnical and structural design, Vessely A. et al. (2007). The development of numerical analysis techniques utilizing the method of finite elements (FE) also enabled better analysis and design of slopes stabilized using piles. A FE-based approach was successfully utilized to design slope stabilization with target safety factor based on the shear and bending demands and the spacing of the piles, Pradel D. et al. (2010).After Hurricane Sandy in October 2012, the stability of many properties constructed atop earth slopes located along the coast of the Atlantic Ocean has become a concern due to storm-induced erosion. This paper presents the analysis, design and construction of a hybrid slope stabilization system utilized at one of these storm-impacted properties, which is located in the Atlantic Highlands, New Jersey in the United States. The subject property consisted of a two-story residential dwelling and a parking structure, and was built on top of an about 8-m-high earth slope having crest at about elevation 10 m (el 10) and toe at about el 2."

Jan 1, 1900

By Sudip Basack

"The topic of pile foundation subjected to lateral cyclic load is an age-old problem confronted by Geotechnical Engineers. The environment prevalent in ocean and shorelines necessitates the piles supporting offshore and onshore structures to be designed accounting for the lateral cyclic loading resulting from the effects of sea waves. The quasi-static nature of this type of loading induces remarkable deterioration in the interactive performance of the soil-pile system. This can be manifested as progressive loss in pile capacity associated with increased pile head deflection. The work reported herein is aimed towards conducting rigorous theoretical analysis using finite difference technique so as to analyze the lateral cyclic loading response of a single, vertical pile embedded in cohesionless soil. The theoretical results are compared with the experimental results and reasonably good agreement is noted. This paper presents a brief description of the theoretical analysis carried out with some typical results and the relevant conclusions drawn therefrom. 1. INTRODUCTIONOffshore structures, namely, quay & harbour structures, jetties, tension leg platforms, oil drilling platforms, etc. are largely supported on pile foundations. Apart from usual loads from superstructures, these piles are subjected to continuous action of wave loading. This type of lateral loading is quasi-static cyclic in nature which results in considerable degradation in the interactive performance of the pile-soil system initiating progressive reduction in pile capacity associated with increased pile-soil stiffness. This may ultimately lead to disastrous consequences.Amongst limited research works in this field, the major contributions are made by Matlock (1970), Idriss et al (1978), Poulos (1982), Vucetic et al (1988), Long & Venneste (1994) and Basack (1999). A brief review of these works indicates that the degradation of the pile-soil system under lateral cyclic loading mainly depends upon the following parameters: number of cycles, frequency (cycles per unit time), cyclic load level (ratio of cyclic load amplitude to the lateral static ultimate pile capacity, in case of loadcontrolled mode) and cyclic displacement level (ratio of cyclic displacement amplitude applied at the pile head to the external pile diameter, in case of displacement-controlled mode). As pointed out by Poulos (1981 & 1982), the degradation is mainly due to: 1) partial to zero dissipation of excess pore water pressure generated during cyclic loading in progress, 2) destruction of interparticle bond with particle realignment and 3) rearrangement and gradual accumulation of permanent plastic deformation around pile"

Jan 1, 2005

By Benjamin B. Buensuceso III

Crosshole sonic logging (CSL) is a popular quality assurance and quality control method used to examine the concrete quality of cast-in place deep foundations, though the evaluation of the results is subject to certain limitations. One such limitation explored in this paper is the occurrence of false positives, where signal anomalies indicated by CSL test results are not necessarily indicative of imperfections in the foundation that could affect its performance. A case study of false positives evaluated in CSL records in a major infrastructure project in Metro Manila is presented in this paper. A detailed desktop evaluation and results from complementary high-strain dynamic load testing and low-strain pile integrity testing were used to evaluate the significance of the suspected false positive signal anomalies from the CSL test results. Recommendations for the proper interpretation and evaluation of CSL test results in Philippine practice, given the method’s limitations and examples presented, are also shared.

Sep 8, 2021

By Saba Mohan

This study presents results based on the Pile Installation Demonstration Project (PIDP) that was conducted as a part of the East Span San Francisco-Oakland Bay Bridge Seismic Safety Project. For the three full-scale pile installations, two different high-energy hydraulic hammers were selected for the installation. However, these hammers may not have sufficient energy to drive these large diameter piles at their ultimate capacity following long-term set-up. Nevertheless, these hammers were selected because, soil plug behavior, the generation of excess pore pressures and remolding of soil during driving were expected to reduce the shaft and end bearing resistance, and therefore reduce the energy required to drive these piles to design penetration. Data collected during continuous installation driving and after a series of re-strikes at different set-up times ranging from 1 to 33 days were used as input data for CAPWAP. These results were used to estimate the soil resistance along the pile length and at the toe of the pile, and the soil pile set-up behavior. Validity of the procedures used to predict the soil resistance to driving and predicted blow counts were verified with the field observed blow counts and the energy that was delivered to the pile. Based on combined CAPWAP analyses, the soil pile set-up with time was estimated and compared with results of other methods currently available in the literature for predicting the soil pile set-up rate.

Jan 1, 2002

By K. Rainer Massarsch

"Part 1 of 2 By K. Rainer Massarsch, Geo Engineering AB, Stockholm, SwedenINTRODUCTIONConstruction activities, such as driving of piles and sheet piles, soil compaction or excavation generate noise and vibrations. In populated areas these can have a negative impact on the environment, disturb inhabitants and, under unfavorable conditions, cause damage to buildings and installations. This condition is aggravated by the growing public awareness of environmental issues and the increasing use of vibration-sensitive electronic equipment and machinery in industry. In many countries, environmental regulations are enforced more stringently and limit or even prohibit the use of impact or vibratory hammers. This development has restricted the use of cost-effective foundation methods, such as driven and vibrated piles and sheet piles.Vibration problems are gaining importance in many European countries and extensive research has been performed during the past decade, especially with respect to traffic vibrations (Massarsch, 2004). Significant progress has been made owing to the availability of high-quality field measurements and an improved theoretical understanding of how vibrations are generated and transmitted through soil layers. These findings can also be applied to vibration problems associated with construction activities. However, this information is not yet appreciated by the geotechnical profession and even less by the construction industry.This paper discusses the effects of ground vibrations on the surrounding soil and on buildings, with particular emphasis on the different mechanisms of damage that may occur. Guidance is given on the elements which should be taken into account in an assessment of risks associated with piling projects. A simplified method is proposed for assessing the risk of settlements or strength loss in soil deposits. Limiting vibration levels are presented, based on the Swedish standard, which can be used to assess the risk of damage to buildings. Aconcept to predict ground vibrations caused by pile driving and the mechanisms which control the propagation of ground vibrations, will be presented in the second part of this paper."

Jan 1, 2004

By Dan Brown

Deep foundation contracting for transportation projects in the United States has typically followed the design-bid-build model in which contractors bid on a specific work product according to relatively inflexible prescriptive specifications. With continuous flight auger piling and the many types of proprietary drilled displacement auger piling, there appear to be advantages to contracting this work according to a different model. This paper provides a discussion of the use of a performance specification for this work in which the contractor has greater freedom to choose the most appropriate foundation system and also greater responsibility for the performance of the completed foundation. With public agencies subject to open bidding, this type of contractual arrangement presents opportunities to encourage innovation. There are also challenges for implementation in public works projects, notably the selection of qualified contractors and the verification of performance requirements on production foundations.

Jan 1, 2006

By Quanchen Sun, Mohammed Z. E. B. Elsahife, Anthony Fisher, Chris Barker, Jennifer Schooling

A review of the literature shows that pile integrity is a significant concern in pile construction. Recently, a new integrity test, thermal integrity profiling (TIP,) has been put into use in foundation construction. It measures temperature changes and thermal profiles of concrete during curing. Heat generation and dissipation of early-age concrete is determined by the concrete mix, the ground conditions and the shape of concrete structure. The current data interpretation practice is primary based on experience. Anomaly detection through direct analysis of temperature profiles is currently indicative or suggestive and temperature signatures are usually similar, and numerous causes are not easily isolated. The core of the TIP testing technique, i.e. collecting detailed temperature measurements along the pile during the hydration process, is promising but a new interpretation approach is required. In this paper, a new interpretation approach has been developed in which TIP constitutes the first step. An investigative staged process is then followed to establish and assess the anomalies in the problematic regions along the pile employing the combined use of detailed finite element (FE) simulations, the actual temperature data from TIP and genetic evolution algorithms. In each stage, more details could be revealed about the anomalies being investigated including, ultimately, location, size and shape; this staged process enables practitioners to follow a riskbased approach and decide whether or not to pursue subsequent stages depending on the results they get at the end of each stage. This new approach, depending on the stages required for the analysis, will potentially avail practicing engineers of crucial test results about the quality of the pile immediately following pile construction, hence enabling repair and remedial work straight away at a lower cost.

May 1, 2022

By David J. Puller

As part of the value engineering process on a major Design Build highway project, instrumented trial pile load tests were used to achieve savings in cost and time on the foundations for a major river crossing. Two trial piles were tested close to failure load at 25MN. Following the interpretation of the pile load test results which included the determination of the ultimate shaft and base capacity, the mobilisation of the shaft and base resistance with pile displacement, and correlations with vertical effective stress and SPT profile, a revised design methodology was proposed. A 25% enhancement on commonly assumed ultimate shaft friction in Chalk was adopted. In addition a significant reduction in the Factor of Safety on end-bearing capacity generally used was also implemented. The revised design resulted in a significant cost and time saving on the piling operation with the pile length reduced by up to 6m (approx. 20%) for the river piers.

Jan 1, 2002

By Jason N. Scott

It is now possible using low-cost wireless technology and rugged hand-held devices to record data on site electronically and for that data to be instantly available to others. This could potentially eliminate many problems that traditionally lead to remedial work, such as poor communication and the late detection of non­conformances. However, determining how best to implement such a system and integrate it with the rest of the business process is far from simple. This paper looks at Stent's experience of these issues by way of a case study of the SHERPA system. This is a wireless site data collection system developed for use with rotary bored piling.

Jan 1, 2006

By Heman Manchanda, Jyoti Agarwal

Several infrastructure projects are under construction in India; many of them involves construction of deep foundations like reinforced concrete and steel piles to support super structures. As most of the piles being constructed in India are reinforced concrete bored piles, there are always uncertainties relating to the quality of construction, and in this case non-destructive methods to ascertain quality of piles becomes very crucial to success of any project. Non-destructive pile testing is becoming more and more popular with growing technologies wherein geophysical techniques and wave propagation theories are being used for pile quality and length analysis. Low-strain pulse echo method and cross-hole sonic logging testing are two pile integrity testing techniques being currently practiced in India which are cost effective and provides reliable near accurate results if analyzed properly. Paper presents current practices being adopted in India for conducting these two tests, highlighting the critical site considerations and analysis techniques. The paper also discusses various execution and interpretation challenges faced by practicing engineers and recommends a way forward.

Sep 1, 2022

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The subsurface soil profile consists of up to 50 ft of a soft organic silty clay layer that is very vulnerable to scour, underlain by a deep deposit of hard sandy clay. Foundation construction in the Potomac River required the use of cofferdams to allow structural concrete work to be performed in the dry. This paper will the present the types of cofferdams used to construct the foundations for the WWB replacement project. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over a navigation channel in relatively deep water. Foundation construction included the installation of 48" to 72" open end steel pipe piles and cast-in-place concrete pile caps. To achieve the desired bridge appearance, pile caps were required to extend below the water surface and below the existing river bottom in shallow water locations. Conventional steel sheet pile cofferdams with tremie concrete seal were used to construct fixed span, shallow water piers. Selection of deep water bascule span foundation cofferdams was governed by several factors including contraction scour, environmental considerations and cost. Potomac River cofferdams, i.e., relatively shallow depth cofferdams that are supported by the foundation piling were selected. This cofferdam system provided a shallow profile which minimized contraction scour and the amount of filling in the river. Design issues include load selection and cofferdam stability in very soft alluvial soils. Construction issues include erection sequence, tremie concrete mix design and placement procedures.

Jan 1, 2005

By Shigetoyo Yasui, Masahiro Saitou, Nobushige Yasuoka, Keisuke Tsujimoto

"The Dry Jet Mixing (DJM) Method was developed and has been put to practical use on the initiative of the Public Works Research Institute and Japan Construction Method and Machinery Research Institute. This method is used to inject powdery binder with compressed air into soft ground while mixing the binder with the soil using the mixing blade to reduce the moisture content of the ground and cause chemical reactions between the soil and binder, thereby strengthening the ground and stabilizing its quality.Recently, there is a demand for high-quality, high-accuracy execution control.This paper introduces the New DJM Execution Control System, developed to meet the future demand for more sophisticated ground improvement, based on the past results of the conventional system in order to provide new automated execution control with improved accuracy, functionality and column quantity.1. INTRODUCTIONIn association with the densification of cities and the improvement of the social overhead capital, the underground space in urban areas is tangled with various underground structures including transportation facilities such as subways and underground roads, buried pipe such as water supply and sewerage systems,gas, electric power and communications lines, and underground malls.In addition, a lot of aboveground structures such as office and residential buildings, elevated tracks, expressways, embankment tracks are also supported with underground foundations.Tokyo, Osaka, Nagoya and many other large cities in Japan grow on plains spread along the coast or rivers. Waterfront flat areas which are very convenient for human activities, however, are often on the alluvial soft ground, where soft cohesive soil with a high moisture content, loose sandy soil, etc. are accumulated in a thick formation, with a high groundwater level.The DJM Method introduced here is used to decrease the moisture content of the soft ground, strengthen the ground and stabilize the soil quality by injecting powdery binder into the ground with compressed air, while mixing the binder with the soil using the mixing blade.2. OUTLINE OF DJM METHODThe DJM Method is used to inject powdery binder with compressed air into soft ground, while mixing the binder with the soil using the mixing blade, to cause chemical reactions between the soil and binder, thereby decreasing the moisture content of the ground and strengthen and stabilize the ground."

Jan 1, 2015

By Emad Farouz, Ehab S. Shatnawi

"The increasing demand for small deformations and high-capacity drilled shafts without enlarging drilledshaft diameters has motivated the development and increasing use of a base grouting (BG) technique. This technique has been demonstrated to improve drilled-shaft capacity, especially for shafts tipped into loose cohesionless soils. Nevertheless, there remains considerable uncertainty in predicting the performance of base-grouted shafts, particularly for shafts tipped into cohesive soils. To date, there are only two documented design methods for estimating the axial geotechnical resistance of base-grouted shafts: Tip Capacity Multiplier (TCM) and Axial Capacity Multiplier (ACM) methods. A comprehensive test program was carried out during the design phase of the Wisconsin Zoo Interchange project to help optimize the flyover ramp’s foundation design. The test program included installing and testing one base grouted shaft and one ungrouted shaft at two sites with different ground conditions. Based on test results, it was concluded that prediction of the TCM method is well correlated with the measured values for both cohesive and granular soils; however, both methods tend to underestimate the axial resistance. Results also highlighted the importance of the base-grouting criteria in taking full advantage of the base grouting.INTRODUCTIONBase-grouted drilled shafts (BGDS), also known as post-grouted drilled shafts, consist of conventionally installed drilled shafts that contain access grout tubes placed within the shaft during construction. After installing the drilled shaft and achieving the pre-established concrete strength, grout is injected at the shaft tip through the access grout tubes to improve soil behavior around the drilled-shaft base. The tip grout injection improves the overall shaft capacity and reduces settlement through Densifying the in situ soils, compressing any debris left by the drilling process, preloading the soil beneath the tip to mobilize the shaft base resistance within service limits, increasing the tip area, and increasing the side resistance in the lower portion of the shaft."

Jan 1, 2016

By W. G. K. Fleming

Mr P. Bermingham introduced paper 9.1, describing the development and trials of a new pile load-testing technique that the Authors had termed "Statnamic". The system involved launching a test weight mounted on the head of the pile by igniting chemical fuel in a pressure combustion chamber between the pile head and the test weight. The expansion products from the burning fuel generated large pressures which were used to launch the weight upwards at high velocity. The reaction from this force generates an equal and opposite force at the pile head. This force is typically of much longer duration compared with, for instance, dynamic load testing by drop hammer. In addition the pile experiences a much lower acceleration - typically of less than one g. Because of the long duration blow, the pile is loaded at below its natural frequency and is therefore under a uniform high stress over its full length throughout the duration of the test. The pile behaviour is not dominated by the complex action of an impulsive stress-wave as with standard dynamic testing. The test technique is thus essentially quasi-static. It was anticipated that a ram test weight of 16 tonne would be sufficient to provide the test reaction for a 600 tonne load test. It was pointed out that the device was still at the research stage, but had yielded encouraging results to date. Testing would proceed from model testing and computer simulation to full scale field testing.

Jan 1, 1991

By D. Dreher Whetstone, Paul M. Blakita, Christopher M. Reith, Ravi P. Malviya

"Micro-piles are small diameter (5 to 10 inches), cast-in-place piles which can develop high load capacities by bonding with soil or rock. Micro-piles are particularly well-suited for moderate to heavily loaded structures requiring deep foundations in difficult subsurface conditions, such as karst, bouldery mine spoil, or unsuitable fills with concrete debris or other obstructions. Attempts to install conventional deep foundations including driven piles, drilled piers, or auger-cast piles are likely to be fraught with construction difficulties and disputes, delays, cost overruns, and may be unfeasible in some cases. Micro-pile installation equipment is very effective in installing foundations through such overburden or rock materials.This paper presents case histories of Micro-pile installations on two projects with difficult soil/rock materials. The project sites are located in Charles Town, West Virginia and Masontown, Pennsylvania.Charles Town, West Virginia ProjectThe Charles Town project entailed construction of a four-story pre-cast concrete garage. Triad Engineering, Inc. performed a geotechnical investigation for this project (Triad, 2001). The subsurface, geologic, and project specific information described in th is paper are largely based on the aforementioned geotechnical report.Ground ConditionsThe project site is located in Jefferson County, West Virginia, and is mapped to be underlain by the Elbrook Formation. This formation is described as argillaceous, dolomitic limestone with beds of dolomite and aphanitic and algal limestone (Dean, et al. , 1990). The carbonate rocks at the site were characterized as ""moderately solution-prone, highly calcareous and weathers differentially to produce a pinnacled or ""sawtooth"" top of rock profile. (Triad, 2001 )"" Overburden soils consist of low to high plasticity, fine grained residual soils formed by weathering of the parent carbonate rock. The residual soils include variable proportion of sand and rock fragments."

Jan 1, 2005

By Joshua R. Omer

A numerical model is developed for predicting the load transfer and settlement behaviour of vertically loaded, bored cast in-situ piles. Based on analysis of full-scale pile tests, closed-form equations are formulated to uncouple the shaft and base transfer resistance components of the pile/soil system. Appropriate parameters are introduced to take into account: (i) the shaft resistance distribution in unlined and partially lined piles, (ii) the effects of ?soft toe? (voided toe pile) behaviour on base resistance development. For convenience, an interactive computer program has been developed in Matlab? with a user friendly interface system. The program can be applied to predict the complete load-settlement curve and axial force distribution in bored cast in-situ piles if reliable soil test data are available. To demonstrate its validity, the proposed method is applied to 4 test piles, which are also analysed using two previously published methods: (a) elastic solution method and (b) layer discretisation method. Methods (a) and (b) above are based on load transfer (t-z) and finite element models respectively. It is shown that the proposed method yields axial force distributions and load-settlement curves that are in good agreement with the observed pile test data.

Jan 1, 2010

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

The city of Naruto in the southwestern part of Japan is situated at the mouth of the mighty Yoshino River. An approximately 1,000m-long levee/bulkhead along one of the river’s tributaries in the city was raised with prefabricated steel panel walls on a concrete base bulkhead. Some sections of the walls’ foundations were combi-walls made of sheet pile cut-off walls and interspaced pipe piles; both of which were installed with press-in piling because the new wall alignment was very close to existing homes and businesses. A Clamp Crane, which clamped onto already installed piles and moved forward and backward on them, was utilized for a segment where the access to its piling location was too tight for a conventional crane or a track-mounted pile driver to maneuver.

Sep 8, 2021

By George J. Tamaro

In 1967 the Port Authority of New York and New Jersey undertook the construction of the World Trade Center (WTC) diaphragm walls, installation of the lateral support system and the excavation of the site, commonly referred to as the "Bathtub". The work took two years to complete. In 2001 the City of New York undertook the re-excavation of the site after the terrorist attacks. The recovery work will take eight months to complete. This paper describes the initial work on the WTC "bathtub" in the late 1960s and the recent work during the recovery.

Jan 1, 2002