Search Documents

By D. Royston

Reducing SAG Mill feed size has been a major trend in recent years. ‘Mine to mill’ strategies have reduced blasted-rock size, and in a growing number of operations reducing the primary crusher CSS and/or adding additional crushing upstream of the SAG mill have reduced rock feed size. While reducing feed size will increase SAG mill throughput, issues arise in terms of retaining charge in the mill, exposing the shell lining to impact damage, and maintaining milling performance should the pre-crush system shut down. This paper reviews the past experience on pre-crushing for SAG mills and provides an analysis of liner design (in particular grates and shell liners) for pre-crushed feed.

Jan 1, 2012

By R. S. Rogers

Abstract - Forensic geology in a mineral exploration context is concerned with geology and related technical matters as they pertain to legal cases involving exploration and evaluation of mineral properties. Such cases involve the possibility of outright scams that include falsification of data and information, as well as inappropriate application of various technical procedures. Experience in forensic geology in such cases emphasizes the need for systematic quality control procedures during routine exploration/appraisal and indicates the need for more attention to ‘target hardening’ (improving security in the chain of custody of samples and assay results). A number of ‘early warning signs’ that might suggest some form of tampering or falsification of information are listed. These measures will support the work of the "Qualified Persons" (geologists and engineers) entrusted with the scientific and technical aspects of mineral exploration, and facilitate the increased attention to regulatory oversight and enforcement of securities laws recommended in the report "Setting New Standards."

Jan 1, 1998

By J. H. McMillan

Most of the recent papers read before the Institute have dealt with purely scientific matters, or with experiences in the various phases of mining operations. Very little, if anything, has been said concerning the part played by the human element in the industry. It is now opportune to consider this vital factor if we are to cope with the complex work of the present-day miner and, at the same time, meet the demands of the executive for greater efficiency. It is time we made an inventory of our knowledge to determine if we are absorbing the information so essential to modern mining practice. We must keep in close touch with all new ideas and developments in our chosen field and keep ourselves up-to-date in regard to everything pertaining to mining operations in general. The man who ceases to study ceases to advance. There are men who on attaining an executive chair give up all study, because they think they have reached the pinnacle of success. Modern industrial business, and coal-mining is no exception, demands that executive officers shall be 'live wires' -- men who are not only well-informed as to their immediate duties, but who are closely in touch with all matters of importance affecting the industry as a whole. We may be graduates of schools and colleges, but the training we receive in these institutions is only the foundation for our later work. Certainly no executive officer can know too much concerning the work he is engaged in, and the more he knows the more pleasure he will get out of his work.

Jan 1, 1925

By D. A. McIsaac

In these days, when mass production seems to be the watchword of all industrial companies, nothing is left undone to attain this end. Transportation, where necessary, becomes a question of very great importance. For this reason every mechanical contrivance known to man is employed, with its resultant advantages. So successful has man's ingenuity been that, offhand, we are inclined to say that practically all transportation on a large scale is done mechanically, that is, where speed and economy are desiderata. Granting this, one would think that to read a paper on the horse before your honourable and highly technical Society would surely be a waste of time, and that any Company employing old-fashioned 'horse' power would certainly be very much behind the time, to say the least. However, the fact remains that the biggest industry in our country today-coal mining-must use horse power to a great extent, being compelled -both by considerations of economy and by necessity. For this reason,' in the production of coal under present conditions, the pit horse is of great importance to this industry and is to be considered seriously as one of the units that help to make coal mining a success or a failure. Hence, in employing horses as a power for transportation, care must be exercised in selecting the animals, and the care of this power must be considered as seriously as any other department of such an organization. In selecting a pit horse, several things must be borne in mind, that is, one must get as much horse power as possible in as compact a form as is practicable. This determines the type of horse we must use, which is of very great importance under our present conditions of coal mining. With low roof, steep grades, and forced production, a distinct type of animal must be selected.

Jan 1, 1930

By Yasuhiro Aoki, Akihiro Sato, Mikiya Arai

In this study, a freckle formation model based on the Rayleigh number was applied to actual multi-component Ni-base single crystal superalloys and verified in large scale casting trials. Finally, new Ni-base SC superalloys having a balance between castability and creep strength has been developed.

Jan 1, 2010

By Murray D. Fredlund

The consolidation of soil material is central to many types of engineering analysis. Problems such as the building of highway structures, landfills, or buildings over saturated soft clays require application of such theory. It has been found in industry that the application of consolidation theory has lagged significantly behind the theory which has been developed some time ago. The application of small-strain saturated consolidation theory was first proposed in a 1D form by Terzaghi. Although this theory has been available for some time it?s implementation into software packages in 2D and 3D forms has been slow due to inherent complexities in the coupling equations. The flow and stress equations are also inherently somewhat unstable and this further complicates software implementation. Of particular interest in the mining industry is the consolidation of uranium tailings. One such disposal method that has been utilized is the subaqueous deposition of uranium tailings in large pit structures. When performing such deposition the calculation of consolidation rates is central to determining final pit capacity and expected life. Consolidation software can be successfully used in such cases in order to determine pit filling rates. The primary complexity, however, is that tailings are typically deposited in slurry form and therefore the potential deformations are large. Large-strain consolidation theory is therefore required in order to properly solve the deformations over time. This paper presents the use of a large-strain consolidation analysis in order to predict long-term filling rates in a uranium tailings pit.

Aug 1, 2010

By Saeid Akhavan

Accumulative roll bonding (ARB) is a severe plastic deformation process for achieving ultrafine grains in metallic sheets without changing the sample dimensions. In this study, ARB process was carried out on 5083 aluminum alloy sheets up to 6 cycles. In this process, the surfaces of the strips to be joined are roughened and cleaned and then stacked. After stacking, the specimen is roll-bonded by rolling using a 50% reduction. The rolled specimen is cut into two halves, and the above-mentioned procedure is repeated for several times. Microstructural characterizations were analyzed by transmition electron microscopy (TEM). Tension and Vickers hardness tests were performed on produced sheets for evaluating their mechanical properties. In order to clarify the failure mode, fracture surfaces after tensile tests were observed by scanning electron microscopy (SEM). The results indicated that at the early stages of ARB process, grains were subdivided by deformation induced boundaries. After several ARB cycles, lamellar structure elongated in the rolling direction contains lamellar boundaries was formed. With increasing the strain, mean spacing of lamellar boundaries decreased. Finally, continuous recrystallization resulted in a microstructure covered with small recrystallized grains with an average diameter below 100 nm at the end of four cycle. The tensile strength and hardness of the 6 cycle ARB processed 5083 aluminum alloy sheet increased about two and three times of the initial values, respectively. Results indicated conformity between mechanical evolutions and microstructural changes during ARB process. Fracture surfaces observations showed that failure mode in ARB processed aluminum is shear ductile rupture with elongated small dimples.

Oct 1, 2011

"Adopted in 2003, theses guidelines are intended to assist the Qualified Person(s) in the planning, supervision, preparation and reporting of mineral resources and mineral reserve estimates. The report is divided into two broad sections “General Guidelines” appropriate for most metals and “Guidelines Specific to Particular Commodities” for potash, industrial minerals, uranium and coal. “These guidelines are reference in the Companion Policy of NI 43-101 with a statement that a qualified person classifying a mineral deposit as a mineral resource or mineral reserve should follow them.”Executive SummaryThe following is a summary, in table format, of the main elements of the Estimation Best Practice Committee's report ""Estimation of Mineral Resource and Mineral Reserve Best Practice Guidelines"". While the summary table is provided for convenience, the Committee recommends that the report be read in its entirety and the table summary not be used as a stand alone document. These guidelines are not intended to be either prescriptive or exhaustive. They do not preclude innovation. Preamble: These guidelines have been prepared by the Canadian Institute of Mining and Metallurgy and Petroleum (CIM) led Estimation Best Practices Committee. They are intended to assist the Qualified Person(s) (QP) in the planning, supervision, preparation and reporting of Mineral Resource and Mineral Reserve (MRMR) estimates. All MRMR estimation work from which public reporting will ensue must be designed and carried out under the direction of a QP in accordance with National Instrument 43-101 (NI 43-101) and related forms. A QP is defined in NI 43-101 as ""an individual who is an engineer or geoscientist with at least five (5) years of experience in mineral exploration, mine development, mine operation, project assessment or any combination of these; has experience relevant to the subject matter of the mineral project and technical report; and is a member in good standing of a professional association"". Disclosure of MRMR estimates is to be made in accordance with industry standard definitions approved by the CIM (the CIM Standards adopted by the CIM Council in August 2002) which have been incorporated by reference into NI 43-101."

Jan 1, 2003

By A Sadough Vanini

In this paper large deformation of smart functionally graded beams with initial imperfection and under thermal loadings is considered. Smart beam consist of two types of layers. One layer is made from functionally graded materials and a layer or a set of layers from active materials that usually is made from piezoelectric materials that are bounded on the surfaces of beam. An active controller is used for controlling the deformation and stress in functionally graded layer of beam. A simple Euler- Bernoulli beam theory is used for analyzing of beam. In functionally graded layer the material property vary continuously through the thickness direction and power law model is used for the variation of elastic modulus, heat expansion and heat conduction coefficients. Poisson ratio is assumed to be constant in functionally graded layer. The effects of varying the power law constants and the Gain of controller is considered here. The results are reduced and compared with smart functionally graded beam without initial imperfections.

Oct 1, 2011

By Saeid Akhavan

Accumulative roll bonding (ARB) is a severe plastic deformation process for achieving ultrafine grains in metallic sheets without changing the sample dimensions. In this study, ARB process was carried out on 5083 aluminum alloy sheets up to 6 cycles. In this process, the surfaces of the strips to be joined are roughened and cleaned and then stacked. After stacking, the specimen is roll-bonded by rolling using a 50% reduction. The rolled specimen is cut into two halves, and the above-mentioned procedure is repeated for several times. Microstructural characterizations were analyzed by transmition electron microscopy (TEM). Tension and Vickers hardness tests were performed on produced sheets for evaluating their mechanical properties. Moreover the texture parameter of the ARB-ed samples was calculated using their XRD patterns and the related equation. Additionally, the texture evolution during the ARB process was demonstrate by analyzing the measured pole figures and orientation distribution functions (ODF) and skeleton lines. The results indicated that at the early stages of ARB process, grains were subdivided by deformation induced boundaries. After several ARB cycles continuous recrystallization resulted in a microstructure covered with small recrystallized grains with an average diameter below 100 nm at the end of four cycle. Texture analysis revealed fiber textures have been discovered with continiuose of the ARB process cupper. Brass, S and dillamor textures identify which their differences are in intensity of ARB process. Results indicated conformity between mechanical evolutions and texture evolutions during ARB process.

Oct 1, 2011

By D. E. Wakefeld

"My first reaction to Joanna LaForte’s discussion paper is that she has quite properly assumed that I would like the process of equitable participation between aboriginal landowners and mining companies to be a fast process. On the other hand, I have been a business lawyer long enough to know that the past experiences of the parties will have a significant effect on how they will proceed at any one time.In my article, I was trying to convey the importance of responding to the wishes, aspirations and fears of aboriginal communities in Arctic regions without land settlements. I agree that if it is necessary to wait for governments, the process will be quite slow. My article did point out that often aboriginal communities and mining companies who have become comfort-able that a project is in their mutual interest regard the government(s) involved as their common enemy. I agree that the education and training of aboriginals should “expedite the negotiations and end the power struggles equitably”. Also, I did not mean to suggest that the elders distrust of changes in traditional land use was solely due to concern for alienation and separation from their offspring; however, I suspect it is one reason for their caution. I also agree with this author that establishing opportunities that enable the young aboriginal community members to remain in the north and avoid the problems that await them in southern urban culture should be a common concern of the mineral developer and the Arctic aboriginal community.When this author suggests I am “overly concerned about how much land the aboriginals will control, how educated they may become, how ignorant they are of mining procedures, how objections from aboriginals will escalate expenses, etc.”, she attributes to me as “concerns” matters that were intended to be general information for my readers. My references to the increased land holdings and the improvement in education of aboriginal peoples was intended to deter mining companies from any attempt to be inequitable in their dealings with aboriginal communities."

Jan 1, 1996

By Russell F. Palmer

"THE PRACTISING MINING ENGINEER has little time for the expression of opinion on abstract questions concerning the definition and future of mining engineering. The following comments indicate some of the thoughts and suggestions of those who have found mining engineering a very satisfying field of endeavour. The future of mining engineering has been under discussion for perhaps twenty years. It is significant that the University of Saskatchewan program was in- 88 traduced at the time that some traditional mining schools were questioning the need for mining engineers. One Canadian university, and some American schools, actually abandoned the field at this time, some ten years ago.Five years ago, Mining Magazine sponsored an international debate on training for the future, and concurrently, the CIM undertook a major survey of the mineral industry's manpower needs. The current CIM discussions should prove more fruitful, as they are directed toward mining engineering alone, rather than the broad, and confusing, spectrum of all professionals and semi-professionals of the mineral industry."

Jan 1, 1972

By Edmund C. Bovey

"AS I begin my remarks this morning, please let me say how honoured and gratified I was to receive your invitation to address you here during your deliberations in historic Quebec City. The high esteem in which your Institute is held is reflected in the respect and deference accorded to it by industry across Canada. I feel privileged to be here with you today.I would like to discuss with you some applications of natural gas in the mining industry and suggest to you, in closing, some possible avenues of future development.Natural gas first became avail-able for industrial purposes in Northern Ontario in late 1958. Acceptance of natural gas, as a source of energy by the industry of that area, has been both widespread and gratifying. The mining industry of Northern Ontario has in-creased its annual use of natural gas by approximately 35 per cent each year since 1958. We believe that this trend will continue, al-though we will probably have to accept a more modest 10 per cent annual gain as the market approaches saturation. I would like to explain how we were able to do this and where all this gas is used. Our first sales were largely a matter of price-and the savings we offered were substantial."

Jan 1, 1966

By S. Brophy

Controlled Short Circuit ? Metal Inert Gas (CSC-MIG) welding is a process that can be referred as a "Cold Welding" technology. The CSC process is based on accurate control of the welding wire position, thus the mandatory requirement for the automation of the process. One of the main advantages of the CSC-MIG process is the rapid solidification of the deposited material, resulting in weldments displaying low porosity contents, and enabling the joining of thin sheet materials. These characteristics render this process an ideal one for freeforming of components, where rapid solidification would be efficacious. This presentation will focus on the progress made towards the freeforming of Al-based components in the NAIN laboratory at McGill University. The relationship between the filler metal used, freeforming (deposition) parameters, resulting microstructure and mechanical properties will be presented.

Jan 1, 2011

By C. Sorel

The PAREX code has been developed since the nineties by CEA and AREVA to describe the PUREX process implemented in the French fuel reprocessing plants. It enables the calculation, either in steady or transitory states, of the behaviour of the different elements of interest at each process step. The high customized structure of the software allowed the implementation of various phenomenological models describing solvent extraction systems dedicated to uranium purification from crude ore to spent fuel. After qualification of the implemented models, the code was used to perform the design of flowsheets, for safety demonstration analysis or for operational assistance.

Aug 1, 2010

By P. M. Chapman

Risks to aquatic receiving environments from uranium mining and milling fall into three categories: physical (habitat change), chemical (e.g., uranium, selenium, total dissolved solids [TDS], metals including vanadium), and radiological. Although all categories of risk need to be managed, chemical risks are the most significant and are typically chronic rather than acute. For instance, selenium toxicity is primarily manifested as reproductive impairment due to maternal transfer, resulting in embryotoxicity and teratogenicity in egg-laying vertebrates. Risk is best assessed using a weight of evidence approach focused on ecosystem services. Risk management should be based on both risk assessment and adaptive monitoring.

Aug 1, 2010

By Arne Renström

A fleet management system such as Minestar with CAES and Aquila could basically be defined as a tool for production control and distribution of drill and load maps, but should also be considered as continuous improvements and a never ending production study. The objective of production studies is to establish facts to be used for production improvements. In a mine operation there are many issues to improve and they spread from achieving productions plans, drilling precision, improved spotting while loading to equipment utilisation. This gives that there is not one single key value to present; we need to manage information presented on maps, as trends, graphs, tables and pre-calculated data for ?free-use? normally in spread-sheets to be able to turn data into useful information.

May 1, 2003

By George McIsaac

This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development and mining method. Based on practical considerations, maximum rates are set for each zone?s development and production capacity. As for the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum number of development metres per day is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Furthermore, the fixed cost of operating the mine is taken into consideration whenever mining activities take place. Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analysed. What-if scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan.

May 1, 2003

By G. Portillo

Electrospark Deposition (ESD) is a pulsed-arc micro-welding process characterized by using high current electrical pulses, of a short duration, to deposit an electrode material on a metallic substrate. The short duration of the electrical pulse allows for a low heat input over the substrate and an extremely rapid solidification of the deposited material. As a result, the ESD is capable of a wide variety of microstructures like micro-segregationfree solid solutions, nanostructured grains, metastable structures, and amorphous phases. The present work shows a microstructural analysis of rapidly solidified Al-Ni alloys coatings by the ESD process. Field Emission Scanning Electron Microscopy (FE-SEM) and X-Ray Diffraction (XRD) were performed to present the microstructural evolution as a function of the welding parameters. The phases and non-equilibrium metastable structures present in the alloys, and their distribution, were found to be a sensitive function of the alloy composition; hence its formation is governed primarily by thermodynamic considerations.

Jan 1, 2011

By E. De Souza

The instrumentation and monitoring of rock behaviour have played an important and necessary role in the practice of potash, rocksalt, gypsum, trona and coal mining. The art of rock instrumentation applied to soft rock and coal mining has progressively evolved over the past years and will surely continue to advance at a faster pace in the future as a result of the technological revolution we experience today. The development of sophisticated mine-wide data communications systems is being used for instrumentation and sensor automation, and laser, sonar and geophysics technology are being continuously adapted for rock monitoring purposes. In this paper, the author provides an overview of typical rock instrumentation used today and offers some views of the progressive evolution in rock mechanics instrumentation sophistication and design.

Jan 1, 1998