Search Documents

By H. C. L. Reemeyer

One of the fundamental trade-offs for copper concentrators is between grinding circuit product size and copper recovery. The capital and operating cost savings and throughput increases for a coarser grind should be evaluated against potential recovery reductions. Other benefits of coarser grinds, such as GHG emissions reductions and favourable effects on tailings and water management should also be considered. This paper assesses the formation of laboratory and pilot test programs, design of process flowsheets, equipment selection, and evaluation methods to determine the most appropriate and economical grind size for a given deposit. The paper will include an evaluation of case studies. INTRODUCTION The majority of the world’s mined copper comes from sulphide deposits, which are mostly processed using crushing, grinding, flotation and dewatering flowsheets to produce copper-bearing concentrates for smelting. Ores must be ground to a sufficiently fine size to achieve an acceptable level of liberation to allow both high recovery of copper and valuable by-product minerals while efficiently rejecting gangue to tailings. Therefore, a key design parameter in process plant design is the grind size of the flotation feed. Copper concentrators use a variety of grind size targets that depend on various factors, including ore mineralogy and the grain sizes of valuable and gangue minerals; the sensitivity of valuable mineral recoveries in the rougher flotation stages to grind size, ore hardness; electricity costs; and mining vs. processing throughput constraints. Typically, copper and by-product recovery increase as grind size is reduced, which can improve revenue, but finer grinds increase power and grinding media operating costs and may have implications for tailings management. This paper explores the trade-offs that should be assessed in determining the optimum grind size, and to answer the question if coarser grinds are worthwhile. METALLURGICAL AND FLOWSHEET FACTORS Recovery-by-size behaviour of sulphide-bearing particles In base metals sulphide flotation, it is typical that flotation recoveries vary by particle size. Metal sulphide particles rendered hydrophobic by collector in intermediate size ranges (e.g. 10 to 100 um) usually show very high recoveries, often approaching 100%. Recovery usually falls away in finer size fractions (<10 um) as fine particles have little inertia and can move around bubbles without colliding and attaching to them. Coarser particles (>100 um) are susceptible to particle-bubble detachment and dropback (Jameson, 2019).

Jan 1, 2019

By Raymond B. Hryciuk

Environmental auditing has evolved rapidly over the last decade — first in North America, then Europe, and most recently in Asia — into a widely practiced discipline designed to provide senior management with assurance that operations are being managed in compliance with established governmental standards, internal company policies, and good industry practices. This paper first examines the evolution of environmental auditing, focusing in particular on three interlocking driving forces: company initiatives, collaborative industry initiatives, and government initiatives. Characteristics of effective audit programs, those that have emerged among the leaders, are discussed, including: objectives, scope, coverage, approach, staffing, and organizational considerations. The author then addresses important future trends and developments for environmental audit program design, content, and coverage.

Jan 1, 1996

By James R. Kuipers

Center for Science in Public Participation CSP2 ? Organized in 1997 to provide technical assistance to public interest groups on mining and water quality issues ? 80%of effort devoted to direct support of grassroots groups and tribal governments ? 20% of effort devoted to public-oriented education for public, tribal, state and federal regulators, and for industry ? Board represented by public interest groups, at large citizens, and academia ? Professional staff with experience from mining industry, academia and government ? website: www.csp2.org CSP2 Mission Statement The CENTER for SCIENCE in PUBLIC PARTICIPATION provides training and technical advice to grassroots groups on water pollution and natural resource development issues, especially those related to mining. CSP2 seeks to focus the debate on factual issues, as brought to light by its technical analyses, and whenever possible to seek consensus and win-win solutions. CSP2 also performs policy related work with federal and state regulatory agencies on the implementation of water quality, waste disposal, and mining reclamation regulations.

May 1, 2002

By Michael Bauer

Increases in productivity and improvements in mining occupational safety and health are intrinsically linked. Over the past years, the German Hard Coal Mining Industry has been able to accomplish both: an increase in coal production and, at the same time, a significantly reduction of accidents. This success has been achieved by advances in technology, better organization and investment in people. Since 1990 productivity has more than doubled, while the total number of accidents has been reduced by more than 90%. Further development started initially with the mechanisation of the winning and drivage technology. Innovative technology and standardisation of the mining equipment were one reason for the increase in productivity and reduction of the accident rate. Therefore this technical development was not only one important pillar of the TOM model explicated later but also the requirement for the successful development of the other pillars. In addition to further developing this innovative technology it was possible to realise procedural and organisational improvements. As a result, the above achievement is based on implementing the three pillars of the so-called "TOM" model (technology, organization, ?Mensch? = human). To increase safety, improve performance, raise awareness and change of employees? attitude, the following technical and organizational requirements have been introduced: ??New innovative technology and procedures, standardized techniques and better equipment. ??Measures to revise or redefine the organizational structure, processes and systems of work, which were then integrated into the company policy and procedures as a company management tool. ??Personnel measures (investment in people). These include, improving motivation and behaviour, training, communication to raise and to change awareness of safety issues. Success in Occupational Health and Safety is not an automatic or self-regulating process. It needs hard work to make improvements and it must be treated as a recurring cyclic process. As a result of the above, occupational health and safety has become a natural part of daily work in the German Hard Coal Mining Industry. This could only be achieved by the unconditional "commitment" of all managers and employees to the issues, coupled with discipline and responsible action. Further improvements towards the ultimate aim of "zero" accidents are only possible by mutual involvement in implementing the ?TOM? (technology, organization and ?Mensch? human) model.

Aug 1, 2013

By J. W. Reynolds

This paper describes the function of the research and development department of a large mining organization and the benefits which can be derived over the years. Examples are given of work done in rock drilling, ventilation, noise control and the development of backfill stowing machinery.

Jan 1, 1970

By Stephen G. Downs

PCF?, or Penetrating Cone Fracture, is a propellant-based technique for rock excavation, which has significant potential for the mechanization of narrow-vein mining. The technique is currently being developed for use in the narrow-vein flat-dipping gold and platinum deposits in South Africa in conjunction with major mining companies. The technique is also applicable to steeply dipping vein deposits, such as those found in North America, Australia and elsewhere. The implementation of PCF? in South Africa to date is reviewed and plans for the introduction of PCF? excavation in other areas are highlighted.

Oct 1, 2001

By T. Melfi, M. James

Attaining required mechanical properties in welds made using the double submerged arc welding (DSAW) process is difficult, and it is becoming more difficult as the strength level of the base materials continues to increase. Producing weld metal with adequate mechanical properties involves factors that are often overlooked and not taken into consideration. Not least amongst these problems is simply finding information to use in selecting the appropriate flux/wire combination. Most of the available data on flux/wire combinations provided by consumables manufacturers is generated using the multiple pass welding procedures required for classification per specifications such as AWS A5.17 and A5.23. This data really gives no insight into the properties that can be expected in a DSAW application. Also, base plate composition plays a very significant role because of the fact that base plate dilution can be as high as 70% in DSAW welds. This means that if any elements are present in the base metal that are deleterious to mechanical properties, they will also be present in significant quantities in the weld deposit. Some of these elements can decrease toughness and increase hardness (increased hardness is a concern if the pipe is intended for sour service). Some of these problems can be mitigated by proper selection of welding consumables. Selection of proper welding consumables means selecting an electrode that provides the appropriate alloying elements to obtain the desired level of impact toughness while also keeping the hardness within any specified limits. In order to attain the necessary impact toughness, selection of a flux with an appropriate composition (in terms of its basicity and its ability to control the nitrogen content of the weld deposit) is required. As with all welding processes, the mechanical properties of DSAW welds are also highly dependent on the welding procedures. This work clarifies how to select appropriate consumables to meet a given set of requirements, and also how to achieve the optimum mechanical properties from those consumables.

Jan 1, 2005

By Donald S. Macdonald

"I AM thankful for this opportunity to address the Toronto Branch of The Canadian Institute of Mining and Metallurgy. The Members of your Institute can have a great influence on the direction in which the mineral policies of Canada will evolve, and to assure that optimum benefits from our country's vast mineral resources will accrue to the nation as a whole and to all its citizens. Today, I want to: (1) offer an outlook on the mineral industry for 1973; (2) talk briefly about the role of minerals in the total economy; and (3) outline some of our thinking with respect to a national minerals policy for Canada."

Jan 1, 1973

By M. Eikerling

The full competition between mass transport and reaction in PEMFC unfolds in cathode catalyst layers (CCLs). Recently developed models provide vital insights into effects of thickness and composition on effectiveness of catalyst utilization and performance. However, the CCL&apos;s key function in liquid water removal is rather unexplored. Studies of water balance in PEMFCs focus mostly on other cell components. Notwithstanding this prioritization, a simple calculation shows that the CCL is the PEMFC&apos;s favourite medium for conversion of liquid water into vapor. Porous structure and wetting properties steer the interplay of evaporation, transport and reaction. A model will be presented, that links pore space morphology, composition, distributed properties (concentrations, pressures, reaction rates, potential) with global performance (critical phenomena). It reveals how problems of flooding in the fuel cell could be mitigated by properly adjusting catalyst layer structure and operation conditions and under which conditions all liquid water arriving in the CCL would leave it as water vapour through the CCL/GDL interface. Results for a simple variant of the model emphasize the role of the CCL as a watershed for the whole cell.

Jan 1, 2005

By M. Piche

The western part of the Hauy Formation of the Opemisca Group, occurring near the town of Chapais, is described in this paper. As it has been defined previously, the Formation is composed of a succession of subaerial andesi tic lava flows with some interbedded proximal volcaniclastic sediments. Towards the East, these volcanics yield to coarse grained fluviatile sediments having similar composition to the interbedded lavas. Further east, the composition of these sediments is more arkosic with dioritic and tonalitic fragments. It is proposed that these arkosic sediments are a part of the Stella Formation which has been described by Dimroth et al. (1982).

Jan 1, 1984

By C. D. Williams

The following paper deals with some of the aspects of the law as it relates to the oil and gas industry in the Province of Alberta, but it should be stated here that consideration of this large subject will be confined to discussion of only those laws, rules, and regulations which affect actual exploratory operations. The paper will not touch on those branches of the law which deal with such matters as income tax, customs, and other kind red subjects which are of a highly technical nature and which are more properly the field of the specialist. Generally speaking, any system of law consists of certain major components. There must be, firstly, a national authority capable of ensuring the existence of the state itself and of maintaining the stability and continuity of its institutions; secondly, a philosophy of government covering the relationship of the state to the individual and of the individuals to one another; thirdly, a body of law to effect the purposes of the philosophical principles; and, fourthly, a judiciary to arbitrate any disputes that may arise from such relationships. All of these components and the system itself are, of course, subject to a varying degree of modification with the changing times and with the influence upon them of other systems of law. Now. while it is true to say that all systems of law comprise these similar basic features, it is apparent that the end result of any two systems of law in their impact upon the individual may be quite different.

Jan 1, 1951

By Jianzhong Liu

Based on the characteristics of overburden rock strata movement, surface ground subsidence and casing deformation and failure, a tension-shear combination failure model of surface borehole was set up. The main controlling factors of the mining-induced deformation and failure of surface borehole were researched with this failure model and the limit analysis method. The mining methods and geology conditions mechanics action mechanism to surface borehole and its time ?space evaluation rule was found. The surface borehole deformation and fracture rule were advanced. It provides theoretical support to optimizing layout, structure type, security measure and local casing protection of surface borehole.

Aug 1, 2013

By M. Stelter

Since the first years in copper electrorefining natural products have been used as so called "additives" in the electrolyte. Glue as one of these additives offers a lot of different reactions with the metal ions and also with other additives like thiourea in the electrolyte. For a deep understanding of the effect of these additives it is important to know the routes of possible reactions in the electrolyte as well as the basics of electrocrystallization. Using this knowledge the interpretation of nodulation or inclusions of electrolyte in the cathodes in copper electrorefining is easier than before. Setting up on physical and chemical properties of the electrolyte and the additives practical investigations of the effects of additives in copper electrorefining and their impacts on copper crystallization and cathode quality are presented in this paper. Chemical deposition of glue against time and temperature are only few of the effects that are mainly caused by the use of natural products. In fact parameters like anodic and cathodic polarization are strongly affected by the additives as well as the effects of the additives are strongly affected by current density. This second part of the paper presents results concerning interactions of the above mentioned parameters.

Jan 1, 2007

By Melinda Bissinger, Frederic Berube

Environmental considerations are important in the aerospace industry. To that effect, several elements such as engine emission, noise and materials are identified by the industry and the society as requiring significant improvements for future and current products in order to be aligned with current expectations. In this context, the industry is addressing this opportunity by investing significantly in new engineering solutions that will meet greener targets. To this effect, the impact of material choice is significant and will make a difference in the forth coming solutions. Several opportunities to develop more efficient products, quieter aircrafts using materials and manufacturing processes that will be more respectful of environmental considerations exist. The presentation will cover those elements and provide an overview of the upcoming solutions.

Jan 1, 2010

By S. Vézina

"Environmental issues have evolved considerably over the last two decades. The main contributing factors, to name a few, have been the changing values of modern societies, the globalization of trade and its linkage to environment, evolution and accessibility of information/ communication technologies, better educated populations, climate change, longrange transport of toxics, and the increasing influence of non-governmental organizations (NGOs) and multistakeholders.As well, environmental management of mining operations had to be realigned in order to meet these new realities and to respond to more elaborated regulations oriented towards sustainability. Environmental management systems (EMS) have been introduced not only to meet the assurance of conformance to regulations but also to prevent pollution and to apply the continuous improvement of mining processes. EMS models have been developed and certification to international standards (e.g. ISO 14 001) is a common practice.Globalization has imposed challenges and additional requirements to environmental management. Developing a mine in emerging countries implies dealing with international agencies, local communities, and a variety of government infrastructures to obtain a “license to operate.” This paper presents the structure of Cambior’s EMS and how it was adapted and implemented in the company’s operations in South America."

Jan 1, 2006

By R. von Gal

Hazelett Strip-Casting Corporation has been producing the Hazelett® twin-belt casting machines for copper casting since the mid-1960s. The first commercial casters were developed for copper alloy strip and anode plate. In 1968, development work was started to adapt the twin-belt caster for copper bar casting to be rolled in-line into wire rod. Since then, 36 casters have been sold as part of the CONTIROD® system for the production of a substantial portion of the world&apos;s copper rod supply. A unique feature of the twin-belt caster is the mold&apos;s ability to comply with the size and shape of the cast bar as it shrinks during solidification. Maintaining contact between the mold and the bar provides a high rate of heat transfer as well as other benefits, including the prevention of surface imperfections caused by remelting in the mold. This paper will give an overview of the continuous evolution of the twin-belt caster technology with an emphasis on recent developments in compliant mold technology for copper casting.

Jan 1, 2007

By O. Zach, K. Gamweger

"The Process of gas purging in molten Aluminium has been an industrial practise for many years. The melting of alloying elements and their rapid distribution in the bath is very important. To improve the mixing and homogenisation process, at RHI NON FERROUS METALS ENGENEERING GMBH a lot of CFD calculations were done. The so developed new ""purging program"" was tested at Alumino Catalan S.A., Spain. The results of the testtrials were very satisfactory and corresponds very well with the calculated data."

Jan 1, 2004

By M. Sabau

The Electrowinning Plant at INCO&apos;s Copper Cliff Nickel Refinery is a precious metals upgrading plant. The feed to the plant contains copper, nickel, cobalt, iron, significant amounts of precious metals and some impurities. Copper is the most abundant element in the feed. This paper describes the major equipment and process changes over the last twenty years, geared to improve the tankhouse operation, workroom environment and recovery of copper from the acidic solution. Copper is plated on to titanium blanks using explosion-bonded crossrods, animal glue as a levelling agent, and an organic surfactant for mist control. The installation of the stripping machine in 2001 required a number of changes: cathode and anode contacts were redesigned, flat bus bars were replaced with dog-bone type, spacer boards for cathodes and anodes were installed, longer anodes started to be used, and the plating cycle was extended from seven to fourteen days. A number of initiatives for improvement are being carried out. Explosion-bonded crossrods are being replaced with titanium-clad crossrods. The plan for the near future is to increase copper production by increasing current efficiency and current density. The possibility of lowering the iron concentration in electrolyte and changing the acid mist control method is being investigated.

Jan 1, 2007

By Juan Pablo Vielma

In this work we study how to incorporate risk control to the generation of ultimate pits when orebodies are modeled through a finite number of conditional simulations. To control risk we consider a chance constraint on the value of the ultimate pit. We incorporate this measure into the generation of ultimate pits by solving a stochastic programming version of the ultimate pit problem. We compare this stochastic programming problem to previous approaches such as generating the ultimate pit for each simulation and the hybrid pit approach introduced by Whittle and Bozorgebrahimi. We also study the effect of using different number of simulations in the generation and evaluation of ultimate pits.

Oct 1, 2009

By Grazyna Zakrzewska-Trznadel

The paper outlines the main objectives of the project that concern the evaluation of the possibility of uranium production from indigenous resources since Poland enters the nuclear program. The best available technologies are considered for uranium extraction and obtaining the yellow cake - U3O8. Liquid-liquid extraction with novel extracting agents, as well as membrane processes for separation of by-products will be tested in course of the project. The technological part will be completed with techno-economical analysis. Acknowledgement The studies were supported by the POIG project, No 01.01.02-14-094-09-00 ?Analysis of the possibility of uranium supply from domestic resources?.

Aug 1, 2010