Search Documents

By Gautier Njiekak

The current study provides an experimental approach that aims at documenting the effects of different phases of CO2 (gas, liquid, supercritical fluid) on rock seismic responses. This has implications on obtaining quantitative estimates of fluid saturations for geological storage. The ultrasonic pulse transmission technique is the underlying methodology used in this work. Unlike previous rock physics studies involving CO2 as pore fluid, care is taken to fully saturate the studied samples and also to separate pore fluid effects from pore pressure build-up effects during the experiments. This allows to record seismic effects that are solely reflective of changes in the pore fluid properties. Measurements were done on a CO2 saturated Berea sandstone. Laboratory results show P- and S- waveform variations (velocity, amplitude) in response to CO2's varying phase state. Overall, CO2 phase changes (gas to liquid and gas to supercritical fluid) are marked by a drop in velocities, with the drop being smaller and less immediate over the gas-supercritical fluid transition than over the gas-liquid transition.

Jun 1, 2012

By John Emery, George Wang

Research and applied utilization activities for the increased use of ferrous and nonferrous slags in construction are presented. The overall use of blast furnace slag is relatively well known for a range of construction applications from aggregates to slag cements. In contrast to blast furnace slag, which is volumetrically stable and straightforward in its construction uses, steel slag contains hydratable oxides that can result in volumetric instability that must be dealt with through appropriate steel slag aging, testing and quality control to ensure its appropriate use. Particular care must be taken to prevent potential steel slag expansive behaviour in confined applications. Quality requirements and guidelines on steel slag expansivity to further the use of steel slags, with demonstrated acceptable performance, are outlined. There is a full range of proven construction uses - from aggregate to cementitious materials - for copper, nickel and phosphorus nonferrous slag. The use of air-cooled nickel slag is presented, based mainly on practical highway construction experience. It has been shown that air-cooled, crushed nickel slag can be an excellent aggregate in granular base, engineered fill and hot-mix asphalt. There is a good potential for increased ground, granulated copper and nickel slags use as supplementary cementitious materials that is being developed, which takes advantage of the 'latent energy' content. The scope of a new technical text in preparation on the technology of slag utilization is reflected throughout to provide a practical context for the engineer.

Jan 1, 2004

By J. Zinck

The management of mine wastes generated by both active and inactive mining is an ever more challenging issue. The cost to manage and treat mine wastes, including tailings, waste rock, treatment sludge and slag, is estimated at over $50B in Canada and the United States alone. Cost-effective technologies are required to meet both short and long term challenges and increasing environmental standards. This paper will provide an overview of novel and conventional technologies to manage mine waste particularly in the areas of waste stabilization, treatment and disposal technologies.

Jan 1, 2004

By Patrick Laflamme, Jean-François Boulanger

Les minerais de cuivre sulfurés, qui représentent 80% de la production mondiale de cuivre, imposent une étape de concentration des minéraux, premièrement pour atteindre une teneur en cuivre minimale qui permette le traitement pyrométallurgique, mais aussi pour limiter la présence d’élément pénalisants (délétères). Cette introduction offre un survol des principes, limites et pistes d’améliorations touchant la concentration des minéraux de cuivre.

May 2, 2024

By F. R. Archibald

IN a recent paper on Roasting of Beattie Concentrate (1), the importance of controlling the temperature, and the sulphur dioxide concentration was pointed out. It is the purpose of the present paper to present further information by which the most satisfactory conditions for roasting are more specifically defined. Incidentally, a method of illustration is developed for representing roasting curves on a three-dimensional diagram. The primary purpose of this investigation, as in the case of the earlier work, was the search for information that would be of practical value in improving plant operation and gold recovery. For this reason, emphasis is laid on the regulation of essential variables and on definition of their optimum values and limits for maximum gold recovery in the subsequent cyanidation process. Good roasting is considered at least as much an art as it is a science, and, in this light, theoretical consideration of the nature and sequence of the chemical reactions involved is of secondary importance. The presentation which follows includes a series of graphical illustrations, an interpretation of the graphs, some theoretical considerations, and a description of laboratory technique.

Jan 1, 1940

"Energy efficiency in mining and minerals processing has attracted considerable public and industry attention because of the significant quantities of energy consumption involved. In this context the question of what are worthwhile targets for energy efficiency improvements ought to be of the highest priority. It is however worth taking a step back to avoid falling in the trap of taking preconceived ideas that have been reiterated repeatedly before as gospel. The aim of this paper is to highlight areas where new or alternative approaches could potentially be the better way forward. Some may come as a surprise to conventional industry thinking. Ultimately any such solutions are attractive to practitioners not just in an environmental but also in an economic sense, and hence should be targeted through applied research and development efforts. This paper highlights key aspects of each group of opportunities and some of the individual approaches to provide an overview of the current status quo.MINING INDUSTRY POWER UTILISATION – WHERE IS THE BIGGEST BANG FOR THE BUCK?The question of where is the biggest bang for the buck when trying to determine worthwhile targets for energy efficiency improvements has not always been reported on broadly enough, typically because industry practitioners operate in specific areas of expertise and comfort zone. Looking beyond the familiar doesn’t always come easy. Any technology or methodology consideration to address energy efficiency needs to take into account the context of alternative opportunities of superior value or risks not achieving desired uptake. The following sub-chapters have been ordered by magnitude of improvement potential as best as is possible, starting with the biggest first, and the smallest last. Some may be a surprise relative to conventional mining industry thinking."

Jan 1, 2016

By F. O. Verret, A. McKen, G. Chiasson

Several grindability tests were developed over the years to design grinding circuits or optimize existing operations. Each test has its own strengths and weaknesses and it is imperative to select the proper test procedure(s) to meet project deliverables and minimize the risk of a project. Pilot plant testing of large bulk samples historically constituted the traditional approach for AG or SAG design, but was gradually replaced by small-scale tests. Nowadays, conducting grindability tests requiring only a few kilos of material on several samples is a more typical approach to grinding mill design. This paper summarises the requirements and deliverables of various bench-scale test procedures, their strengths and weaknesses, and cases where AG/SAG pilot testing should still be performed.

Jan 1, 2012

By P. Mottahed, E. De Souza

One of the major unsolved problems of safe, economical roof support in the evaporite industry has been that of obtaining and maintaining anchorages in relatively soft rock. This is due to the viscoelastic and viscoplastic behaviour of salt rock and associated deposits. This paper introduces a low-cost, yieldable support mechanism, consisting of a system of buckling disks, which provides viable solutions to dynamic support. The yieldable support system offers a number of advantages in comparison with existing dynamic support systems. It is characterized by its simplicity in design and installation, repeatability in behaviour and cost effectiveness. It also has the added advantage of providing the operator with a means of assessing support behaviour and ground performance by direct visual observation of changes in disk shape. Thus, the system can be utilized as a warning mechanism of ground stress and support load conditions. Such system not only provides a feasible and more effective rock mass stabilization strategy but improves mine safety.

Jan 1, 1999

By W. T. Boyes, J. M. Harrison

"Squall Lake Gold Mines, Limited, owns a group of claims at Squall lake, northern Manitoba, about 75 miles east of Flin Flon and 3 to 4 miles north of the Nor-Acme mine at Snow lake. Gold mineralization was discovered in this locality several years prior to 1944, but it was only in that year that a comprehensive examination of the occurrences was begun. Development work to the end of 1946 has been encouraging and the deposits show interesting relations to rock structure.GEOLOGICAL SETTINGThe gold occurs in a sill of biotite-hornblende diorite at or near its contact with gneisses derived from arkosic sediments . In detail, the contact between the diorite and the arkose to the southeast of it is irregular, with interfingering of the two rock types. On the northwest side of the sill, between it and Squall lake, the rock is staurolite schist (see accompanying sketch-map).Several mineralized shear zones are known, of which those shown are the most important. Within the zones, the diorite is silicified and somewhat carbonatized. Fairly coarse arsenopyrite is the chief sulphide mineral in these zones but, locally, they contain also pyrite and pyrrhotite. Where quartz and chlorite are present, rather coarse gold is associated with them. In that part of the main zone where gold assays have been most consistent, the diorite is rich in albite."

Jan 1, 1954

By W. K. Coughlan

The Wabana deposit of Dosco Industries Limited is situated on the east coast of Newfoundland, at Bell Island in Conception Bay. It is a Clinton-type iron-formation of Lower Ordovician age. Five separate beds have been recognized, with others noted locally. Economic production has been obtained from the Lower, Middle and Upper beds, which are second, third and fifth in sequence, al-though at present only the Lower Bed is worked. The potential area of occurrence is about 70 square miles. It i;; bounded by major faults to the north, east and west and truncated by erosion at the south, where rocks of the de-posit crop out on the north side of the island. The iron is contained in oolitic hematite and chamosite, with minor siderite. As the deposit is submarine, conventional exploration methods are not applicable and much interpretation and projection from mined areas is necessary to guide exploration and development. With the interpretation of information from existing mined ores, it is possible, using a minimum of diamond drilling in advance of working faces, to maintain adequate ore reserves.

Jan 1, 1966

By Murray W. Grabinsky

This paper considers thickening mine tailings to dense non-segregating slurry or paste for surface disposal. The driving motivation for this initiative is the elimination of ponds, reduction in containment dams and significant decrease in water being sent to the tailings basin. This inherently reduces risks of environmental and structural failure. Some of the engineering challenges in creating a stable stack of thickened or paste tailings are identified, and possible field and laboratory testing techniques in support of design are discussed. Finally, the integration of monitoring activities into the ongoing management of the surface disposal site is considered.

Nov 1, 2002

By B. T. Lu, J. L. Luo, T. Yu, C. W. Chen

In this paper, the synergism in erosion-corrosion process occurring in oil sand wastewater transportation caused by the interaction of mechanical and electrochemical factors was experimentally investigated. The erosion-corrosion tests were conducted with A1045 steel in synthetic slurries comprising tap water and silica sand. The material loss due to corrosion-enhanced erosion was assessed with the chemo-mechanical model developed by the authors recently. The results indicate that the material loss produced by corrosion-enhanced erosion at the open circuit potential can be formulated as a linear function of logarithm of corrosion current density. The wastage caused by the erosion-enhanced corrosion was analyzed based on the concept of non-equilibrium thermodynamics. The material loss induced by the erosion-enhanced corrosion is approximately a linear function of overall erosion rate measured in synthetic slurries, indicating that erosion-enhanced corrosion could be reduced by adopting surface strengthening techniques to improve the resistance to the plastic deformation in surface layer.

Jan 1, 2004

By A. G. Doll

The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less. This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference.

Jan 1, 2012

By T. Motegi

Semisolid casting provides grain refinement of the cast structure and prevents macro-segregation. The conventional semisolid slurry is obtained by electromagnetic or mechanical stirring. In our process, the magnesium alloy (AZ31) slurry is made using an inclined cooling plate instead of the conventional methods. The slurry obtained is cast into a twin-roll caster and makes a continuous sheet of 2 or 3 mm thick. The most important factors that influence the sheet casting are the casting temperature and twin-roll speed.

Jan 1, 2007

By J. Lammers, D. Adams

Most pressure oxidation operations introduce oxygen through a large multi-use nozzle in the vapour space of the autoclave. Sparge pipes extend inside the vessel to the point of discharge below the compartment agitator. However, two zinc pressure leach operations have successfully used a bottom entry oxygen sparge system for a number of years. Recently, the concept has been used in a whole ore gold pressure oxidation operation as well as a copper pressure leach plant. Both of the latter operations also introduce cooling water for temperature control through the same sparge pipe. This paper addresses the benefits of the bottom entry system with regards to autoclave performance and the positive effects on agitator performance.

Jan 1, 2004

By W. Kempson

"As has been noted on numerous occasions, the vertical shafts being sunk around the world are all tending to get deeper as we seek to take advantage of higher grades of minerals which can sometimes be found at greater depths. One of the challenges with these deeper shafts is the requirement to supply services to the mine’s operations at depth as well as the requirement to dewater the mine. Both the supply of water and the dewatering of mines is generally done using piping. With the greater shaft depths, this piping is now required to contain higher pressures as well as to accommodate changes in temperature resulting from normal mine operations. This paper will discuss the requirements for the design of high pressure piping in deep vertical shafts. The discussion will start with the general definition of the systems and the detailed design requirement. Once this is clearly outlined, we will discuss the options available for fulfilling these requirement as well as the advantages and disadvantages of each of the systems. We will finish with the installation recommendations and provide a basis for the maintenance of these systems. INTRODUCTION Piping in vertical shafts is used to provide a number of services in underground workings. These services vary depending on geographical location and the type of the ore body which is being mined. For example, in the Zambian Copper mines, one of the largest requirements for in shaft piping is for dewatering. Similarly in the Gold deposits in the West Wits basin as well as the deep level Copper deposits in Arizona, one of the largest uses for the piping is the supply of a cooling medium to underground workings to create a safe working environment (this can in the form of water or of glycol depending on the application). In South Africa, systems were installed which used the hydrostatic head which is generated from supplying chilled water to mines whose depths exceeded 2,000 m below surface. This chilled water was supplied as a closed system, allowing for high pressures to be generated which was then used to supply useful work (for example, Rock Drills, Face Cleaning and other ancillary services) whose power was traditionally supplied by compressed air or electricity. This system was initially researched by Chamber of Mine in South Africa. The design pressure range of these systems is 14 MPa to 18 MPa."

Jan 1, 2019

By E. You

Kennecott Utah Copper Refinery and Outokumpu Technology have developed a wireless Electrolytic Cell Monitor (CellSensor) system to monitor cell voltage and temperature. The system is based on a robust self-organizing and self-healing wireless network with a very reliable redundant structure. The microprocessor controlled CellSensor device operates off a small amount of energy harvested from the cell bus and requires no external power source. The radio works in the 2.4 GHz international ISM band using robust Spread Spectrum technology. The CellSensor does not require end user calibration of either the voltage or temperature sensors and accuracy is superior to previous systems. The on-board computation power allows digital filtering of the cell voltage signal which results in very high quality data. The system requires much less maintenance than conventional hardwired systems and is intrinsically safer since no high voltage isolation is required. The advanced diagnostic functions allow the device to determine if the bus tap contact is degrading. The CellSensor can also be used for monitoring electrowinning (EW) cells for a variety of metals. CellSensor have been tested for over two years at the Kennecott Utah Copper and Boliden Harjavalta Pori refineries. The CellSensor system is now commercially available through Outokumpu Technology.

Jan 1, 2007

By G. I. Mathieu

"An experimental study was carried out to evaluate the performance of column flotation versus conventional flotation for the recovery of molybdenite from a Newfoundland ore. The objective was to verify the claims made by the inventors of the flotation column, Messrs. Pierre Boutin and Remi Tremblay, that their apparatus reduces the entrainment of fine gangue and other mineral impurities in the froth product. The research included a factorially designed series of tests to determine satisfactory operating conditions of the column. These provided a basis for comparative flotation tests with column and Denver cells. In the course of the work, the action of a few depressants was studied. Results indicated greater selectivity in the column and reduced reagent consumption."

Jan 1, 1972

By P. Cavanagh

Summary This paper discusses the fundamental principles which allow the development of a new method for studying the deformation and failure of metals in terms of 'internal microstrains'. Internal microstrains mechanical and magnetic properties are defined and their influence on of metals is outlined. A research programme at present in progress will determine whether magnetic measurements of internal microstrains give sufficiently accurate values for predicting the performance of metals under service conditions. These magnetic test techniques are also being used to detect the beginning of plastic deformation and to trace the development of deformation processes and failure. Results of the experimental work in each field will be published. Introduction Any attempts are being made to develop a complete theory embracing the mechanical behaviour of metals. In spite of the amount of experimental data available, the theoretical approach is rather difficult, since most of the mechanical properties of a metal are determined by deviations from the pure chemical composition or the perfect crystal. Both types of deviation are difficult to reproduce experimentally and to describe theoretically. In general, there are three main avenues of approach to the problem being followed today.

Jan 1, 1950

By O. Kodym

The paper has focused on possibilities of interconnecting information sources concerning monitoring & control of mining industry technical processes (TP), and the related safety hazards. The key issue is the comprehensiveness of the information presented to users. Information can be presented by virtual reality means, when the seemingly true presentation of the production process scene along with user friendly presentation of related information is available. The user in its role of a process supervisor is not only a mere scene observer but, thanks to the interactive functions of virtual environment, he participates in the scene of his control. As such his control and management abilities increase because he can absorb, more easily understand and asses the information provided.

Aug 1, 2013