Search Documents

By Holt. Grover J.

"IntroductionThe history of iron ore production in the United States has followed a pattern not far different from that set in the production of non-ferrous ores; the first interest of the prospector and miner being the discovery and development of high-grade ores. In the early stages of development of most mining districts, high-cost low-grade ores are usually of slight interest due to the additional capital investment required in concentrating plants, as well as the increased requirements of •power and other facilities. As the reserves of higher grade ores are depleted and the technical knowledge of ore beneficiation is broadened, production of concentrates from the lower grade ores is stimulated.The real stimulus necessary to arouse serious consideration of beneficiated iron ore in the Lake Superior district has been provided by the serious inroads made in the high-grade ore reserves by two World Wars.The first shipment of high-grade iron ore from the Mesabi range in Minnesota was recorded in 1892, and the first token shipment of concentrates was made 15 years later, in 1907. Not until 1910 did the production of concentrates assume any great importance. A steady increase in concentrate production over the years is shown by the fact that, in 1910, concentrates accounted for 8 per cent of the total shipments from the State, whereas by the time of World War II this percentage had increased to 22 per cent and by 1948 had risen to 26 per cent. It seems a safe assumption that the shipment of concentrated iron ore, from the Mesabi range in particular, will continue to increase even more rapidly from now on, with other iron ranges of the Lake Superior district following this lead."

Jan 1, 1950

By F. McIntosh Galbraith

EMPLOYING geophysics to find ore was for a long time considered by the Canadian mining fraternity to be a performance of dubious value: in a category somewhere between the practice of sorcery, and using a divining rod to locate underground water. With increasing knowledge, however, and with constantly improving instruments, a solid speaking acquaintance with this adolescent science is becoming an integral part of the mining geologist's stock in trade. And quite properly so: for, in the established mining districts, the ore deposits which could be easily found, by ordinary prospecting methods, have already been located. There remain; however, in almost all of the principal mining camps, areas which are covered to varying depths by glacial debris; and it is here that the obvious opportunities exist for the successful application of geophysical methods. Geophysical results must always be considered in the closest possible relation to the local geology; and, in reality, the 'doodle-bugs' are simply additional tools for the geologist (in the same category with a plane table or a microscope). The Sudbury Basin is a shining example of precisely this state of affairs. Detailed geological mapping has not significantly altered the position of the outer norite contact as placed on Dr. Coleman's original map of the district. What detailed examination has done, of course, has been to reveal the accuracy with which the contact can be placed in different parts of the district, and to show up, in consequence, areas in which further work might reasonably be expected to disclose hitherto unknown or unsuspected ore. Viewed in this light, the proportion of the norite contact which is covered by substantial quantities of overburden is astonishingly large.

Jan 1, 1939

By Alfred W. G. Wilson

THE ultimate purpose of the Chemical Manufacturer is to produce consumer products which can be sold to customers. Such production and sales can be continued only if the operations yield a profit to the manufacturer and if the products meet the requirements o the consumer--bath parties to the transaction must be satisfied. There are vast numbers of consumer products, made by chemical pro-cesses. The production of some of these ultimate products may involve the use of several intermediate chemicals, applications of few or many different processes, and the utilization, somewhere in the series of operations, of a variety of raw materials. On the other hand, some ultimate products have a very simple chemical history between raw materials and end products. There are no chemical products in use which are completely independent of the mineral industry. For many, the association is direct and obvious; for others, it may be indirect and even obscure. Analyses of the process and raw-material ancestry of a very large number of consumer products would suggest that many products are derived from Industrial Mineral products directly, that there are many in which the connection is indirect, and that there are only a few products with which industrial minerals are not in some way or other associated. The vast majority of the more important chemical products, and especially the basic chemicals from which other products are made, are directly dependent for their production upon Industrial Minerals or their derivatives. In the preceding part of this paper, for each raw material mentioned some references have been made to the leading chemical products based on this material. This, however, is only part of the story, because in most cases the consumer product can be made from any special raw material mentioned only by the use of other materials or chemicals made from them. The production of consumer chemicals is really possible only through an intricate interlocking of processes, materials, and apparatus.

Jan 1, 1940

By D. Houghton

"I am very pleased to be a member on this panel today because abrasion and wear in mills has been part of my life over the past forty years. My presentation will deal with the role Ni-Hard has played in combating wear and abrasion in mills. Before Ni-Hard came along, unalloyed white iron was used in ball mills and one of the most popular types of white iron liners was the pocket liner. Slide #1 illustrates the design of the pocket liner used at Dome Mines in their 5' x 22' pebble mills. The pockets filled with grinding media and it was on this that the wear took place. The concept is not unlike the new magnetic liner which utilizes the ore and grinding media to form the wearing surface. In this slide please note the tapered pocket type of cored bolt holes. If cored bolt holes do not fill with grinding media there could be excessive grooving or wear at that area. Therefore all cored bolt holes should be tapered in this manner.Before Inco patented the name Ni-Hard several foundries were making the alloy iron under different brand names such as Diamond Alloy, Mitchelloy and Specialloy. In the early days some of the Ni-Hard was poor quality. Inco provided foundries with technical knowhow and provided assistance to licence them to sell under the name of Ni-Hard. This was in the late 1920's. The material we are discussing is Ni-Hard type I with the following analysis (slide #2). It is a martensitic white iron with BHN of 550 - 600 and is a relatively easy alloy to produce in either a cupola or electric furnace. The annual average production of Ni-Hard in North America is 90,000 tons with mill liners making up 25,000 tons and grinding media 30,000 tons, according to Warren Spear of Inco."

Jan 1, 1983

By D. A. MacLeod

DURING the past fourteen months, dust surveys have been made at thirty-six mines in the Province. These surveys are made to determine the concentration of dust in the mine atmosphere, the flow of air through the mine, the methods adopted to prevent the generation of dust, and the measures taken for its elimination. When high concentrations of dust are encountered, suggestions are given for its prevention ?and elimination wherever possible. Dust sampling is absolutely necessary to determine the effectiveness of any measure taken in the prevention and elimination of dust in the mine workings. Consequently, more time has been spent on this phase of the work than on any other. The apparatus used is the Devers circular konimeter and Zeiss microscope. At various mines, the Zeiss konimeter is used, and the dust counts taken by the two instruments have given results that are closely comparable; so much so that either instrument can be used with confidence and the results obtained will compare in accuracy with those obtained by the methods used in Ontario and South Africa. Before the Workmen's Compensation Act Amendment Act was passed in November, 1936, most of the mine operators were already keenly interested in the prevention of silicosis. This interest has been intensified at all the mines, and measures have been adopted to decrease the amount of dust in the mine atmosphere. Several operators have spent a large amount of time and money in bettering these conditions, and have met with decided success. Practically all others are adopting the known methods of prevention, suppression, and elimination of dust, that apply to their ?particular mines. To prevent the production of dust in underground workings should be the first, as it is the most important, aim, especially during the time the men are underground. An atmosphere free of dust cannot be obtained, but measures can be adopted to lower the concentration that is found? in the average mine.

Jan 1, 1939

By W. L. Falconer

"IntroductionThe very recent emphasis on the importance of the northern portions of the Alberta basin as a prospective oil province has led the oil companies northward into new and undeveloped territory. Northern Alberta is a land of continuous forest, covering a plains-type topography. The plains are only occasionally broken by sharp, broad river valleys. Tributary streams head up quickly and very soon lose themselves in large undrained areas. It is these pseudo-swamps that cause most of the troubles and headaches of the oil explorer.The rivers have served as the main transportation arteries since people first ventured into this area. The bush is being pushed back, but the advance is slow and there is very little more than trappers' trails beyond a few miles from the Northern Alberta Railway lines and the recently built Grimshaw or McKenzie Highway. Indeed, bush and muskeg flank many miles of the railways and roads within as close a distance as fifty miles of Edmonton. Northern Alberta is pioneer country in the truest sense of the word, and our greatest problems derive from this fact. In all pioneer areas, the first requirement is the development of access roads, and before active oil exploraton can get down to the job at hand these roads and trails must be an accomplished fact. There are two factors in Northern Alberta which offer discouragement to the oil explorer: the first and greatest stumbling block is presented by the numerous muskegs, large and small; the second is the fact that road building uses up so much of reservation time. Of course, the second is aggravated by, and a direct result of, the first. So we come back to the main problem facing the development of the north - the muskegs."

Jan 1, 1950

By J. M. Wetherill

"This paper presents the results of an investigation into the level of radon, as against the natural background, at the Vicary Creek coal mine in Alberta. The concentrations of radon and daughter products detected in the mine were considered to be insignificantly higher than the concentrations of naturally occurring radon and thus do not constitute a health hazard to the miners.INTRODUCTIONTHE HIGH INCIDENCE OF LUNG CANCER among miners exposed to radon was established some thirty years ago. The presence of this gas in mines is primarily associated with pitchblende extraction operations, al-though coal contains detectab`e quantities of U30s. A previous study bas shown that coal from southwestern Alberta (Exshaw and Banff) contains lower than average concentrations of this element (1).As part of a general investigation into the occupational health environment of coal miners in Alberta, field measurements were made to establish the level of radon and to investigate the natural background radiation in the Vicary Creek coal mine, located some 16 miles north of Coleman, Alberta, on the easternmost slopes of the Rocky Mountains."

Jan 1, 1968

By H. H. Gardner

Introduction The Greenhill mine of West Canadian Collieries, Limited, is on the Alberta side of the Crowsnest pass, twelve miles from the Alberta British Columbia boundary-line. Here, five coal seams of Lower Cretaceous age are found in the Kootenay formation. They outcrop on the north and south slopes of the valley, with strike approximately N.30°W., paralleling the main range of the Rocky mountains, and dip about 40 deg. westward. Of the five seams, only two, designated No. 1 and No. 2, have been worked to date. On the West Canadian Collieries property, No. 1 seam ranges in thickness from thirty feet to nil. Generally, it has a hard, strong conglomerate roof. No. 2 seam is separated from No. 1 by forty-five feet of shales and sandstones. It has a thickness of eight to thirty feet.

Jan 1, 1947

By E. P. Evoy, A. W. Jolliffe

"The Uranium deposit of Gunnar Mines, Limited, is on the south shore of Crackingstone peninsula in the Beaverlodge area of northern Saskatchewan.The ore consists of disseminated pitchblende and uranophane in brecciated syenite, and forms a tubular or pipelike body, outcropping at the surface and plunging southward at about 45 degrees for a known length of1,400 feet (see Figure I). The upper portion is being removed by open-pit mining to a depth of 300 feet below adjacent Lake Athabasca. The remainder will require underground mining methods (see Figure 2).The property was staked in July, I 952, and the orebody was subsequently defined by about 70,000 feet of diamond drilling. A 1,250-ton mill was completed in 1955, and production commenced in September of that year with ore from the open-pit operation. The mill is presently being increased to 1,650 tons capacity, and a three-compartment vertical shaft is being sunk to 1,250 feet in preparation for underground mining.GeologyThe mine property is underlain by an assemblage of Precambrian metasediments known locally as paragneiss, granite-gneiss, and syenite. These lie on the southeast limb of a southwest-plunging anticline, strike about north 75 degrees east, and dip southward at about 45 degrees. Para- gneiss outcrops in the northwestern half of the claim group, and again on the islands south of St. Mary's Channel. The granite-gneiss lies conform-ably within the paragneiss and makes up the southeastern part of the property. The syenite forms an irregular, triangular-shaped mass within, and near the footwall of, the granite-gneiss band. Small lenticular bodies of mafic rocks are also present, the former being most prevalent in the paragneiss.The granite-gneiss is coarse to medium-grained, pink to grey, well foliated, and composed of feldspar (65 per cent), quartz (20 per cent), chlorite, and minor mica. The general concordance of its contacts with paragneiss and the absence of intrusive relationships along these, the presence of uniformly oriented inclusions of obviously sedimentary origin within the granite-gneiss, and the variation in colour and texture across the strike all strongly suggest that this member represents a granitized sedimentary rock."

Jan 1, 1949

By J. Baumbach, H. Bombach, M. Stelter

"Today technical electro-refining processes for copper exclusively use sulfuric acid, for silver refining nitric acid electrolytes are used. Sulfuric acid is characterized by very good chemical and electrochemical stability, good conductivity and low cost. The disadvantages of sulfuric acid are the precipitation of fine-grained cathodes with smooth surfaces only by using additives like glue, thiourea and chloride. In case of silver the electrolyte is electrochemical unstable and bears the risk of the formation of toxic NOx when pH is too low. A second disadvantage is the form of electrodeposition of silver as dendrites with their removal from the bottom of the Möbius cells.This paper reports the results concerning the application of an alternative electrolyte in copper and silver electro-refining. At first the electrolyte was characterized by the determination of current density potential curves. Electrolysis experiments were performed in laboratory scale using technical anodes for copper and synthetic anodes for silver. During the copper tests the solubility of contaminations from the anodes and the amount and chemical composition of the anode slimes were determined. Moreover the influence of current density, electrolyte temperature and the effect of several additives on the precipitation and chemical purity of the cathodes were investigated. In all experiments cell voltage as well as anodic and cathodic polarization was measured and current efficiency and specific energy consumption were calculated. A comparison with the results with those of tests using conventional sulfuric acid electrolyte shows the advantages and disadvantages of both systems, additionally the technical application chances and limitations for the new electrolyte. This electrolyte enables the precipitation of smooth copper cathodes with low silver and sulfur concentrations even at lower temperatures without any additive. For silver refining the electrodeposition of compact silver sheets is possible, that can be stripped comparable to those in copper electro-refining."

Jan 1, 2016

By A. A. Tytko, T. S. Golosinski

"The paper discusses the accuracy of magnetic inspections of corroded hoist ropes. It quantifies the error of measured LMA (loss of metallic area) caused by presence in the rope of ferromagnetic products of corrosion. The paper concludes that in mining practice this error is not significant. Hoist Rope Corrosion and its AssessmentCorrosion is one of the most common forms of wire rope wear. For ropes working in wet mine shafts, ropes used by the fishing industry and, in general, ropes working in humid and chemically active environments, corrosion wear is usually the prime reason for rope discard. In most mining applications, rope corrosion is accompanied by fatigue cracking of wires, abrasion of external wires, internal nicking and other forms of wear.Quantification of corrosion damage in ropes using standard inspection procedures and examination methods is very difficult. Qualitative comparisons are sometimes used to describe the degree of rope corrosion to compensate for the lack of quantitative measures (SABS 0293, 1996). If available, the results of magnetic examinations of ropes may be of help in assessing their corrosion weakening.Magnetic rope examination requires that the rope first be magnetized. After that, the rope magnetic flux and the leakage flux along the rope are measured. The first is assumed to be directly proportional to rope metallic area (LMA) and its changes are indicative of the rope’s loss of breaking strength (LBS). Existence of the second indicates existence of local faults (LF) in the inspected rope. As the corrosion of rope results in development of corrosion cracks and in loss of rope metallic area, both the LF and the LMA should be used to quantify the level of rope corrosion. More specifically, the changes to the amplitude of the LF signal are considered to provide qualitative information on rope corrosion (Hansel et al., 1990), while those of the LMA signal are believed to provide quantitative information (Geller and Rousseau, 1990; Golosinski, 1996)."

Jan 1, 1999

By L. H. Smith, D. S. Taylor

"AbstractSherritt has been applying hydraulic drives to concentrator equipment since 1967. The initial application was made on a bank of 5- by 5-in. slurry pumps. This has now been extended to all slurry pumps requiring less than 40 hp and several conveyors which require variable-speed or low-speed/high-torque characteristics. The pump motors are directly connected through a flexible coupling, whereas the conveyor systems are directly mounted onto the head-pulley shaft extension.The different applications and design concepts will be described, with outlines of the operating and maintenance advantages and disadvantages and costs. The paper also outlines future possible applications, together with the limiting conditions, of such systems.IntroductionSHERRITT GORDON MINES LIMITED has been operating a mining division in Northern Manitoba for almost 50 years. The original mining operation was at Sherridon, Manitoba and was a copper-zinc producer. This mine was exhausted in 1948 and the mining plant was moved north to its present location at Lynn Lake, Manitoba. The Lynn Lake Mine is a nickel-copper producer. Since 1960, two new mines have been discovered and brought into production in the general vicinity of Lynn Lake. The first of these was the Fox Mine, a copper-zinc property operating at 3,000 tons per day from an underground operation. This mine started production in May 1970."

Jan 1, 1977

By M. A. Keogh

This paper reviews the physical properties that make low-density polyethylene the most practical and economical material for launder• fabrication in the majority of mine and mill applications. The basic design features and use of other launcher• materials are also discussed.

Jan 1, 1976

By S. N. Yu

Tele-operation manipulators applied in this paper are systems for the remote handling and management of pyroprocessing related facilities in an Argon cell of the KAERI (Korea Atomic Energy Research Institute). Generally, these kinds of systems are composed of a master-slave system and its peripherals installed along the wall of the cell, with the master transmitting the user?s own motion to the gripper directly. This study introduced various considerations and modifications to improve the remote handling performance. The analysis of an operator's ability using his/her own upper arm motion range while manipulating the MSM, and considerations of its manipulation margin and the related tool modifications are also included. Finally, the test results of several remote handling tasks are presented, and an adequate operation strategy for the tele-operation system of hot-cell type facilities is proposed.

Aug 1, 2013

By H. Vermette, J. Demers, R. Leclerc, P. Bergeron, P. Hudon, A. Lessard

The Arvida Smelter marked its 80th anniversary in 2006. Arvida currently operates 6 potrooms equipped with prebaked side-feeding pots producing 160 000t of aluminum per year, requiring the supply of 300 000t of alumina per year. In the past, to ensure reliable alumina supplies to the pots, especially in winter, a safety stock of alumina was kept inside the plant. The improved reliability of shipping on the Saguenay River has cut the need for such a stock. However, the stoppage of 8 Soderbergtechnology potrooms, starting in the 1980s up to 2003, generated alumina from the cleaning of pot pits, totaling 18000t and leading to the building-up of a significant alumina stock again. Concerns over working conditions, effect on potroom operations, and dust emissions prevented Arvida from tackling effectively this impressive alumina stock. Yet the increasing cost of alumina has created a strong motivation to use the stored alumina. In 2004 Arvida launched a project to recycle the stored alumina. This 4-year project aimed at clearing the alumina stock without affecting the operation of the smelter. It involved changing work organization, improving equipment and controlling the effect of the recycled alumina on the smelting process and working conditions.

Jan 1, 2006

By John A. Dresser

Seventy years ago a period of prospecting and mining activity began in the Eastern Townships of Quebec that seems to have been quite equal to that of recent years in the Rouyn field. In the following six or seven years a large amount of work was done over a widespread area. About fifty deposits gave some shipment of ore, from a few tons upwards, and as many as five hundred occurrences of copper were made known in the district by official records. Comparing the scale of commercial undertakings of that time and of the present day, these developments must have occupied quite as large a share of the capital and man-power of the Province as northern Quebec employs today. Working conditions at that time were not very favourable. The country was then only newly opened for settlement, and colonists were few and widely separated. Roads of the class built today were unknown. A single line of railway, the Grand Trunk, crossed the district from east to west. Colonization companies controlled large blocks of land on which they owned mining rights and usually reserved these rights in whole, or in part, when selling the lands. Then, as now, the precious metals belonged to the Crown. Yet the work was not without its successes. One of the first deposits discovered, the Acton, was, for a few years, one of the most profitable producing copper mines of its time. Another, the Eustis mine, has been in almost constant operation ever since, and is now vigorously pushing further development. At least two others, now quiescent, proved profitable operations, and several made considerable production. The manufacture of sulphuric acid in Canada was begun by the founder of the Nichols Company at Capelton, on a deposit that is now being re-developed, after a long and creditable career.

Jan 1, 1928

By Marc Piard

In a cool mine, tapping high-pressure lines through reducing valves lowers the temperature beyond remedy. It is the writer's suggestion that, for low-pressure work, law-pressure air ,should be generated in a compressor installed underground adjacent to the work, and that the jacket-water of the compressor should be utilised for re-heating purposes. Such a system of compressed air distribution, designed especially for service in cool mines, is described in the following notes. The suggested system includes a three-wire pole line from the sub-station to the opening nearest to the working face, with a cable connection extending to the latter from the openings; an electrical centrifugal unit; a reservoir excavated in the ground; and a distribution line, re-heated by jacket-water. As regards the reservoir, it may be pointed out that in many mines there are blind or abandoned tunnels that could be used for the purpose. The centrifugal type of compressed air machine is a comparatively new departure, and it was formerly considered that such a machine, operating at less than 1,000 kilowatts per unit, would be commercially impracticable. At the present time, however, these machines are being built in Europe for as little as 400 kilowatts per unit, and as much as 110 lb. per sq. inch pressure. One advantage which these centrifugal machines have over other types is that they may be driven by plain induction motors, without the help of special starters-a consideration of the first importance where the electrical regulations are severe.

Jan 1, 1926

By P. G. Dunn, J. Fitzgerald

ABSTRACT The scheduling of underground mining activities is a complex task that must simultaneously satisfy a large number of constraints. A schedule optimization tool (SOT) for underground mine planning is described, and its use for investigating strategic decisions is illustrated through a case study. The maincomponents of the SOT include (a) a genetic algorithm that searches for optimal schedules, (b) guidance for the application of heuristic rules, and (c) sliding, which implements just-in-time development. Findings indicated that preliminary scheduling performed before invoking the SOT, intended to provide a good starting point for the search, did not ultimately lead to higher value schedules.

Jan 1, 2010

The Environmental Excellence in Exploration (E3) project is driven by the recognition that the minerals industry can only maintain its long term viability by ensuring its continued access to lands to explore for, and develop, new mines. Widespread implementation of sound environmental management practices by the exploration community and improved education and understanding of that by stakeholders will help substantially in accomplishing this, and E3 is designed to meet these needs. Exploration crews are now viewed as ambassadors for the global mining community. Their performance in managing the environmental aspects of an exploration program can demonstrate a commitment on the part of the international mining sector to environmentally responsible exploration and mining. We have all observed that failure to behave responsibly can alienate local residents, encourage anti-mining NGOs and jeopardize development. As the saying goes, ?you don?t get a second chance to make a first impression?, and we want to make a favourable first impression. The E3 project is focused on creating an electronic manual, the e-manual, which will provide rapid access to the most up-to-date information on environmental management practices for minerals exploration globally. The e-manual will reflect current thinking and practices in environmental management. It will be richly illustrated with actual examples that reflect the realities of exploration. It will strive to identify the key environmental issues and concerns that apply to most exploration projects, and identify other sources of relevant information useful to field practice. It is our belief that E3, or something very like it, is central to ensuring that the industry survives the current challenges to its viability. E3 will be a cornerstone of the mining industry?s drive to sustainability simply stated, if we are not permitted to explore for mines, there will be none of them at some point in the relatively near future.

May 1, 2002

By G. C. Bateman

Canada is a very large country with a small population which is growing very slowly. We have great natural resources, but with our limited population we are continually looking afield for new capital to develop these resources. Our mining areas are among the most important fields offering opportunities for new capital and because of the wide-spread appeal which mining makes this industry commands a great deal of attention. While we are glad to see new capital from any source, we welcome it particularly from Great Britain, for, although we offer equal opportunities to the nationals of any country we would be glad to see the development of our natural resources financed as far as possible within the Empire. However, when we invite ne capital we must accept certain responsibilities, and while we have opportunities to offer, we should ask ourselves how these opportunities are taken advantage of and what sort of treatment the foreign investor receives.

Jan 1, 1925