Search Documents

By R. Thierbach, W. Kahnt, Oberthür. T., D. Eisenburger, V. Gundelach

ABSTRACT: The ground penetrating radar (GPR) method was used in a platinum mine in Zimbabwe by members of the Federal Institute for Geosciences and Mineral Resources (BGR). The measurements were carried out in boreholes and drifts. Electromagnetic re?ections from a fault that consistently trends parallel to the mineralization zone permitted the mapping of the economically minable parts of the deposit. An introduction is given to the geology of the studied area and the application of the GPR method. The electrical parametres of the rocks are measured in situ, the GPR measurements are displayed with radargrams, and the visible structures are explained in illustrations.

Jan 1, 2010

By I. Caraconcea, M. Cousineau, S. Gariepy

"Several base metal plants operate in low grade/high tonnage conditions which impose strict cost control on all fronts for their operations to remain profitable. This leads to decisions regarding plant design, procurement, operations and maintenance that often favor cost minimization over value optimization. This may hinder the representativeness of the metal accounting systems while this should be a priority in a low margin environment. Such poor representativeness not only creates confusion in plant scheduling but can also hide suboptimal metallurgical performance. Furthermore, this situation can run undetected for a while since one dominant feature of a poor metal accounting system is its poor self-awareness. During their practice, authors have particularly identified measurement bias and reproducibility, as well as their impact on metal recoveries as areas of concern. These issues have not been extensively reviewed in the specific context of precious metals in base metal plants. Pragmatic solutions are proposed either at the design stage for a new project or to retrofit an actual operation. These solutions should be based on a business analysis that set a value of information matching the contribution of precious metals as well as the potential to use such information to act toward increasing plant profitability. Conclusions are that trade-offs are an inherent part of the design/audit/retrofit of any metal accounting system in any plant processing either base or precious metals. However, compromises must be evaluated on economic/technical ground.INTRODUCTION Every mineral processing plant must produce metal accounting reports (Morrison, 2008) where estimated saleable metal flows and inventories are published. These metal accounting reports are delivered to a variety of stakeholders who use them for internal management purposes (day-to-day plant production planning, plant operation optimization, capital spending, etc.) as well as for external management (royalty settlements, tolling agreements, etc.). Hence, there should be no doubt that state of the art metal accounting is instrumental for mining companies to reach and sustain high-quality corporate governance (Gaylard, Randolph, & Wortley, 2014). However, producing a metal accounting report involves much more than just printing it (Lachance, Leroux, & Gariépy, 2015a). The underlying metal accounting system (Figure 1) is responsible not only for the reliable production of the metal accounting reports but also for the quality of the outcome. As such, the crucial tasks of its design/audit/retrofit should neither be seen as ancillary nor be left as an afterthought."

Jan 1, 2017

By A. Gutiérrez

At present, most ore milling is done in tumbling mills, consisting of huge cylinders turning on their horizontal axis. This rotational motion causes the ore charge and the grinding balls to interact by impact, compression and abrasion, to reduce the size of the ore. This method is very inefficient since only around 12% of the energy supplied is used for actual grinding, the rest being used in moving the large mass of balls and ore within the mill. This work aimed at better understanding the milling process by evaluating the movement of the load through the Discrete Elements Method (DEM). First, the number of bodies (balls and ore) moving inside the mill is determined, to correlate to the potential impacts that constitute one of the milling mechanisms. Then, the number of high energy impacts is evaluated to correlate to the bodies in motion. At this stage, a differentiation between grinding media and the ore, as well as between the types of contact taking place in the mill, has to be made. This latter issue is of great relevance since from the five identified contact types (ball-ball, ball-liner, ore-ore, ball-ore and ore-liner) only the last three actually contribute to the milling process, the other two causing structural damage to the mill.

Jan 1, 2007

By Tibor Horvath

Dust abatement is possible on bulk materials, whether conveyed or stockpiled. Minimum (ppm) quantities of chemical additives can efficiently and rapidly control dust of conveyed substrates with no effect on floatation chemistry. Top coating of large surface areas can control surface dust and wind erosion. Environmental and toxicity impact must be considered in any treatment, especially on areas with percolation runoff, leachates, or limited containment. The most effective dust control is preventing release of substrate fines rather than trapping and removing air borne dust. Techniques to prevent release of fines from conveyed substrates will be discussed. Dust control dynamics are a very complex combination of solid phase physical and chemical interactions between the substrate and the fines. ?Smart Technology? products permit dust abatement of stockpiled substrates and tailing fields with no environmental impact. Using ?Smart Technology?, the dust abatement products remain active and can re-seal damaged areas. Efficient, low environmental and toxicity impact, dust control will be demonstrated through case studies where these principals have been applied.

Oct 1, 2010

By R. D. White

"The Cumberland Basin of Nova Scotia has long been considered a structural basin by virtue of the elliptical outcrop and inward dip pattern of the Pennsylvanian outcrops. Recent published and unpublished data indicate that subsidence began in the late Devonian, perhaps resulting from a graben or rift. The Mississippian sediments which filled the growing depression were continental, lacustrine and marine with evaporites. The cessation of the riftforming processes is recorded by the alluvial swamp-type sediments of the Pennsylvanian which filled the depression. In excess of 25,000 feet of Carboniferous rocks are believed to be present in the deepest part of the Basin. Starting with the rift hypothesis, we can speculate on the kinds of sediments, their location and the structural features present beneath the Pennsylvanian surface. Using surface exposures and a limited amount of subsurface data, we theorize that (1) the Mississippian evaporites acted as glide zones which effectively divided the Basin into two horizontal structural layers. The rocks above the evaporites, responding to Appalachian stresses, formed the long diapiric folds with cores of overthickened evaporites. Below the evaporites the structures are related to movements of the rift floor, compaction closures and structures formed by differential horizontal movements of the rift walls. (2) The rift, in its deeper parts, will have more and a greater variety of marine rocks than the outcrops indicate. Should the rift hypothesis be correct, the possibility of finding hydrocarbons is enhanced."

Jan 1, 1972

By D. D. Downing

This paper is a review of material selection considerations concerning protective coatings in the mining industry. The discussion will cover both capital-dollar projects and maintenance requirements. Emphasis will be on industrial finishes for structural steel and process equipment subjected to aggressive atmospheres. The presentation will cover the total needs of a job, emphasizing not only the owner's requirement for a cost-effective system during plant operations, but also taking into consideration the short-term requirements of general contractors, steel fabricators, erection firms and paint contractors.

Jan 1, 1979

By B P. Scott

Podsol soil horizons developed on Pleistocene glacial sediments overlying the Coronation Mine orebody were analyzed for copper and zinc spectro-photometrically, using biquinoline-isoamyl alcohol and dithizone carbon tetrachloride reagents. Copper and zinc are concentrated in the A. and C horizons, whereas the A1, A2 and B horizons are leached. Of economic significance is the fact that the C horizon contains a copper anomaly, in excess of 100 times back-ground, directly over the orebody. Due to the erratic distribution of high copper concentrations in the Ao horizon with respect to the orebody, that horizon is not considered as a reliable prospecting datum. U NDER certain conditions, metallic ore deposits are accompanied by primary halos of trace elements in unweathered rock surrounding the orebodies or by secondary halos in weathered rock, alluvium, soil, or vegetation above or near the mineralized zones. Where such halos occur, chemical analysis, as applied to the detection of trace elements, is a valuable prospecting aid, permitting the detection of mineralization of possible economic value.

Jan 1, 1965

By J. S. Godard

The mining developments in western Quebec have shown the ores of this district to be more complex in character than was at first expected. When the initial discoveries were made it was thought that the ores would be similar in character to those of Kirkland Lake and Porcupine areas. Developments have since shown that although the ores along the southern margin of the belt are somewhat similar, those within the belt, constituting by far the greater proportion, are vastly different, being complex mixtures of base-metal sulphides carrying values in the precious metals. These mixtures of base-metal sulphides of copper, zinc, and iron, present several problems to the metallurgist, especially in their concentration into marketable products. For the purpose .of this paper the following classification may be made of the ores of the district. Group I. - Milling Ores: (a) Ores in which~ arsenopyrite is the predominating sulphide. In this class of ore the gold occurs in fractures in the quartz and is associated to a lesser extent with the arsenopyrite and pyrite. Examples of this class of ore are the Granada, south of Pelletier lake, and the O'Brien and the Thompson in Cadillac township. (b) Ores in which iron pyrite is the predominating sulphide and gold is the valuable constituent. This may also be classed as a concentrating ore-Group III.

Jan 1, 1928

This paper outlines the position and capabilities of Western Canada's bituminous coal industry, and indicates the increasing importance of Japan as an export market. The use of coal in Japan is reviewed, especially as regards future trends, and an appraisal is made of Canadian coal in comparison with domestic Japanese coal and imports from other countries. The importance of maintaining a solid nucleous within the Canadian bituminous coal industry is emphasized. I N RECENT years, Japan has emerged as a valuable market for Canadian exports. The first major product exported in volume to Japan was wheat, which has become very successfully established in Japanese markets. Following this, iron ore gradually found a market in Japan, with exports usually based on long-term contracts. This iron ore was produced entirely in British Columbia In 1958, the Western Canadian bituminous coal industry -jointly with the Dominion Coal Board -sent an official mission to Japan to investigate the

Jan 1, 1964

By Julie Q. Shang

The electrokinetic (EK) technology for dewatering of two tailings from the uranium mines in Northern Saskatchewan is studied in bench scale experiments. The study includes four phases: 1. Characterization of two uranium mine tailings; 2. Assessment of voltage loss on the coated Ti anode and water interface. 3. EK cell test series to measure electrokinetic permeability (ke) of two tailings; 4. EK dewatering test series to study electrokinetic enhanced gravity dewatering on two tailings samples. The results have demonstrated that both tailings responded positively to the EK process. For the tailings containing gypsum, the EK dewatering should be a short term process (within one hour) with anode conditioning (pH adjustment). The tailings containing clay minerals responded well to EK dewatering, in which pH adjustment is optional and will further enhance the EK flow. Both tailings as tested have low hydraulic conductivity and are particularly suitable for EK dewatering and consolidation.

Aug 1, 2010

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, P. Ghobadi

Design and selection of equipment for a grinding circuit strongly depends on the mill function, ore properties and requirements of the down-stream circuit. Primary mills usually work in open circuit and size distribution of product would be controlled in the final steps using a classifier like cyclone. Although HPGRs are mostly utilized as pre-grinding mills, it is preferred to utilize them in a closed circuit due to their specific mechanism of comminution. Unique mechanical design of HPGR and its completely different crushing process than tumbling mills needs precise consideration on its circuit design. In this paper, we investigate the impact of different parameters on design of pre-grinding HPGR circuit and selection of the proper classifier. Our study focuses on iron ore properties (e.g. moisture, particle size distribution of feed and product, compatibility and de-agglomerability). We also investigated various options of HPGR circuit according the classifier efficiency and influences on down-stream processes. The optimum operating parameters of HPGR (working pressure, speed and level of hopper) for the selected circuit were also determined based on pilot and industrial data. Our pilot and industrial tests and observations revealed that HPGR should be arranged in closed circuit because of the edge effect, as a negative factor of non-uniform distribution of pressure force along the roller width and presence of non-crushed particles in the mill product. Wet vibratory screen could be the optimum option for screening of its discharge. Fine part of the wet screen discharge could be delivered to the concentration stage without over-grinding in ball mill using a hydrocyclone working in a reverse closed circuit mode. Moreover, our pilot and industrial tests during design and operation of ten HPGRs in various iron ore processing plants proved that higher pressure and lower roller speed in a fixed level of material inside the hopper could give the desired product size distribution.

Jan 1, 2016

By Noel Brien, O&apos

General: National Asbestos Mines Limited has operated an asbestos mine and mill near Thetford Mines, Quebec, since 1958. As a result of additional exploration of the orebody in 1962-63, it became apparent that long-range mining plans would have to be revised to allow for a large increase in both ore and waste tonnages. It was decided that the task of checking out possible mine designs could best be analyzed by a computer to obtain data from which an optimum open-pit configuration could be plotted. Object: It was desired to arrive at an optimum open-pit configuration with an over-all pit slope of 45 degrees and a minimum operational width of 200 ft. at the bottom. Calculations were based on assay values from diamond drill holes in cross sections of the mine. The computer's assignment was to select and describe, by coordinates, the optimum cross section for the mine. Mine engineers then assembled the various optimum sections to produce the pit outline. As this would not necessarily result in a practical mining arrangement, the computer also provided alternate solutions,

Jan 1, 1965

By Fred Horne

1N THIS PAPER, the writer proposes to limit his comments to few generalized phases of the subject, based on his personal experience in the midwestern United 'States and in one section .of the Coal Branch in Western Alberta. The following statistics are submitted to show the importance that strip mining has assumed in the coal mining industry of the United States. In 1914, 1,281,000 tons of strip coal were produced, amounting to 0.3 per cent of the total production. In 1948, the total was 13~,505,000 tons, representing 23.3 per cent. In 1949, the percentage figure dropped slightly and this can be partially accounted for by the labour disturbances prevalent throughout the year. In 1914, there were 48 power shovels and draglines being used in the stripping of coal; in 1949 there were 3,712, not to mention other types of coal stripping equipment such as bulldozers, tractors and scrapers, rotary excavators, and stackers. At the bituminous coal mines in Western Canada, strip mining was introduced only a few years ago, two of the major reasons for its development being the need for increased production during the war and post-war years and the need to hold the line on increasing production costs, but even in these few years the percentage of strip production has in-creased to such an extent that some mines that, five or six years ago, were producing all their tonnage from underground operations are today obtaining up to 80 per cent of their total output from strip mines.

Jan 1, 1951

By J. Shanks

In 1920 the writer presented some notes, embodying his experience with storage-battery locomotives as main under-ground haulage-motors at Brazeau collieries. (1) Since that date these motors have stood up well to the test of maximum output and heavy overloads, having accomplished all that was expected of them. The notes presented in 1920 gave a brief description of the conditions under which these motors were working at Brazeau collieries, also the cost, per ton mile, of operating them. The cost per ton mile has since then been appreciably reduced, by working the locomotives nearly to capacity and under more ideal haulage conditions, on both shifts. It is not the intention of the writer to repeat what was written in 1920, but rather to give members the benefit of his experience in operating different types or designs of locomotives; to draw their attention to the drawbacks of some designs, and to the improvements made in some of the more recent storage-battery locomotives put on the market, as regards efficiency, upkeep, and safety. Because of their flexibility storage-battery locomotives have advantages over any other type of haulage, where grades are suitable to their use. The number in use in the mines in the United States has increased enormously during the past few years, and this method of haulage is, at the present time, attracting the attention of British and Continental mining engineers.

Jan 1, 1924

By A G. Rogers

This paper discusses the lubrication of surface and underground mining machinery and equipment from the standpoint of machine components. The machine components considered are bearings, cylinders, gears, chains, couplings, fluid drives, hydraulic systems, screws and wire ropes. The best selection of lubricants for these machine components, and for sub-divisions of the components, are outlined. They form general recommendations, for average operating conditions in both surface and under-ground mining operations. The American Petroleum Institute's service classification of both engine crankcase oils and gear oils is de-scribed and used in recommending products for these applications. The practical aspect of lubrication is kept foremost in the recommendations, which are designed to meet the requirements of a wide variety of equipment with the minimum number of lubricants. THE lubrication of mining machinery and equipment presents a variety of problems peculiar to the industry. The type of mine, the ambient temperature, water, dust, and operating and maintenance practices, as well as the age and condition of the equipment, are variables which have to be considered in making lubricant recommendations.

Jan 1, 1963

By P. Curry, H. G. Stephenson, B. Van Den Bussche

"Three Sisters Resorts Inc. currently owns a2035 acre (824 ha) parcel of land, which previously belonged to Canmore Mines Ltd. Approximately 50% of these lands, that are slated for residential, resort and recreation development, have been undermined for coal in one or more seams.Norwest Mine Services has been contracted by the developer to assess and advise them on any past mining activity that may be potentially hazardous to their development and offer solutions to how these hazards may be mitigated or avoided.The following paper deals mainly with the procedures put in place and accepted by the approval authorities, and the Staged approach to the Investigative Procedure that Norwest follows in the mining assessment and mitigation work for Three Sisters."

Jan 1, 1996

By DON E. MacDONALD

Marl in Alberta is confined to highly specific geological, hydrogeologica/ and climatic settings. Tufa is fa irly abundant in those areas of western Alberta where bedrock is of the Paskapoo Formation. Marl and tufa originate when the following conditions are met: presence of a carbonate source in drift or nearsurface bedrock; leaching of the carbonate by percolating groundwater; transportation of calcium and bicarbonate ions in a permeable aquifer; discharge at the surface as springs, seeps or lakes; re-precipitation of calcium carbonate. Alberta has seven categories of marl and tufa deposits, based upon over-all depositional environment and calcium carbonate

Jan 1, 1984

By Lionel A. York

This paper outlines the type of water-bearing formations encountered in the Prairie Sediments and describes a method for effectively sealing these zones in order that shaft-sinking operations may be carried out with safety. Details are given of the procedure for carrying probe holes ahead of the shaft bottom. These probe or grout holes are employed for establishing a series of overlapping grout covers around the proposed shaft excavation to safeguard against large inflows of water during sinking. The pattern and length of grout covers cannot be standardized, and each cover needs to be specially designed to suit the varying ground conditions. In order to provide effective protection through the Prairie Sediments, the number of holes in any one cover would not be less than 8, and possibly as many as 64 would be required in certain zones. The length of covers would vary from 100 ft. to 250 ft. Emphasis is placed on the need for obtaining accurate geological and water information from exploratory holes, drilled in the shaft vicinity, in order to effectively plan all grout covers.

Jan 1, 1964

By J. Kang

There is increasing demand to utilize aluminium alloy sheets and their spot welds by the automotive industry. While traditional uniaxial tensile tests only determine mechanical properties to small strain, direct measurement of the constitutive behaviour of aluminium alloy spot welds at large strain remains a challenge. A technique was successfully developed using digital image correlation coupled with shear tests to directly measure the constitutive behaviour of an AA6022-T4 spot weld to large strains. The results show that the spot welding process not only decreases the yield strength but also lowers the work hardening rate of the nugget versus the base material. Details of sample preparation, experimental approach and results will be discussed.

Jan 1, 2011

By BARRY BANNATYNE

Gypsum in Manitoba is quarried from the Jurassic Amaranth Formation a1 Gypsumville and Harcus; it has been mined near Amaranth and Silver Plains. At Gypsumville, gypsum is carbonate- free but has thin clay laminae between gypsum layers; the rock is folded in places, and some anhydrite is present. At Harcus, gypsum contains scattered dolomite, both as patches in a penemosaic pattern and as thin layers; small chalcedonic concretions also can be found. The quarry at Harcus was opened late in 1978 and currently produces about 100,000 tonnes annually. The two inactive mines near Amaranth operated from 1932 lo 1963 and from 1967 to 1970, and contain a central anhydrite layer. The mine near Silver Plains was flooded from an underlying artesian aquifer in 1975 and has not been reopened. Manitoba gypsum is used in cemem plants in Mani1oba and Saskatchewan and in wallboard plants in the three Prairie Provinces.

Jan 1, 1984