Search Documents

By W. F. James

Introduction The season of 1927, from the point of view of mining development in the area west of Rouyn, was quite satisfactory. Serious prospecting and development' were undertaken over quite a large area, though the results in the matter of discovering new deposits of economic importance were rather disappointing. A large amount of systematic prospecting and geological mapping was carried out in the course of the work, and a considerable body of information collected. A widespread occurrence of sulphide mineralization was noted, chiefly near bodies of older gabbro. The frequent occurrence of pyrrhotite in or near which local concentrations of chalcopyrite were localized, lends support to the idea that such older sulphides as pyrite and pyrrhotite are relatively easy of replacement by chalcopyrite. From the prospector's viewpoint, areas near the contacts of masses of older gabbro are favourable prospecting ground, and pyrite and pyrrhotite mineralization are favourable indications that massive chalcopyrite may be found where it has completely replaced such sulphides. Pyrrhotite being magnetic is easily located, even where drift covered, by the use of such convenient instruments as the dip-needle and the magnetometer. It is suggested that pyrrhotite bodies, when located, be thoroughly prospected because of the fairly strong probability that they may show replacement by the more valuable chalcopyrite.

Jan 1, 1928

By R. W. Culley

"In many areas of Saskatchewan, known gravel deposits have been depleted or are diminishing rapidly; in other areas, particularly in the north, demands for all-weather highways and access roads are far exceeding the supply of gravel sources with which to surface them. These two problems have made conventional methods of air-photo and ground surveys insufficient for gravel location. In the first case, hauling costs on construction now warrant searching for buried deposits and for smaller, less obvious surficial deposits that may be closer to the project. In the second case, search and access conditions are so difficult and costly that the ratio of successes to failures must be kept very high. The Department of Highways has long been aware of the oncoming scarcity of quality gravel deposits and is continually investigating ways of forestalling it. One of these ways is the use of airborne geophysical methods that permit rapid coverage of large areas and that sense and discriminate between earth properties to a significant depth below ground surface. In 1967, the Department began an investigation of an airborne conductivity survey method called INPUT*, or ""Induced Pulse Transient'', leading to a trial in 1968 and data analysis in 1969. The results of this trial initiated• modifications to the technique to improve its sensitivity for mapping shallow deposits. Part way through this modification in 1970, a decision was made to change to an airborne resistivity survey method called EPHASE*. Trials with this technique were conducted and analysed in 1971. This paper is an explanation of the E-PHASE system and a summary of the results from one of three areas mapped in 1971."

Jan 1, 1973

By B. Dyck, C. Rodgers

ABSTRACT Cameco Corporation is revitalizing its Key Lake Operation uranium mill in northern Saskatchewan. The mill currently uses ammonia stripping in solvent extraction (SX) and ammonia yellowcake precipitation. As part of the revitalization, the company considered installing strong acid stripping in solvent extraction (used at its Rabbit Lake Operation), which would lead to using hydrogen peroxide for uranium precipitation. As part of the process evaluation, tests were carried out to study how the drying temperature in indirect fired dryers would affect the uranium peroxide yellowcake precipitate properties. This paper discusses the test work results, including the relationships between drying temperature and product reactivity with water, product colour, product grade, and energy input requirements.

Jan 1, 2012

By L. V. Bell

"The gold deposits of the Caribou mine are representative of those of the Province of Nova Scotia as a whole. The ore shoots within the deposits, in common with those elsewhere within the Province, are associated usually with interruptions or irregularities in the broader and uniform fold structures. The structural factors localizing ore deposition as applied more specifically to the Caribou mine are demonstrated chiefly by the close relationship of the two principal ore shoots, known as the main orebody and the 'high-grade' vein, with a pitching drag fold developed in the southeast limb of the major northeast-southwest trending anticlinal fold or elongated dome that constitutes the primary structural feature of the Caribou gold district. It is of interest to note that the evidence indicates that this drag fold, in common with other folds subsidiary to the primary fold, formed as a result of movement similar in nature to that which caused the primary fold itself. Presumably, therefore, these folds are coincident in time.The property described here as the Caribou mine is an amalgamation of two adjacent properties formerly known as the Ross and the Nova Scotia Gold, but which since 1934 have been controlled and operated as a unit by The Consolidated Mining and Smelting Company of Canada, Limited. The Caribou mine is situated in the Caribou gold district about 45 miles to the northeast of the city of Halifax and about 6 miles to the north of the Moose River gold district.The history of mining at Caribou dates back to 1867. The first recorded gold production is for 1869. From 1869 to 1933 the gold produced from the mines of the Caribou district aggregated 47,249 oz. from 93,234 tons of ore treated. The grade of the ore on the basis of the gold actually recovered from the district would thus average 72 oz. gold a ton, which, as will be noted from the following, is precisely the grade of the ore treated from the Caribou mine during operations by The Consolidated Mining and Smelting Company. These operations commenced in September, 1934, and milling on a commercial basis was under way during 1938. Since that time production, apart from a short period in 1945 during which efforts were concentrated on development work, was continuous to early in 1947, when the mine closed down owing to exhaustion of the known orebodies. Gold produced from the Caribou mine by The Consolidated Mining and Smelting Company from September, 1934, to the close of 1946 aggregated 43,205 oz. from 90,754 tons of ore milled; the grade of ore treated averaged 0.50 oz. gold a ton. The indicated average grade of O.S oz. gold a ton for the ore of the Caribou district throughout its mining history ranks somewhat higher than the 0.37 oz. a ton average for the ore milled to date from the several gold districts throughout the Province as a whole according to the production statistics of the Provincial Department of Mines."

Jan 1, 1954

By B. R. Johnston, K. D. Streeter

"ABSTRACTCoal Mountain Operations is the newest of Fording Coal’s operations although it is the oldest in terms of its historical production. In October, 1994, Fording purchased the former Corbin Creek/Byron Creek Mine. The mine is located in southeastern British Columbia, approximately 150 air kilometers from Calgary, Alberta. It was first developed in 1905 and has gone through a variety of owners in its 90-year history.This paper will deal with the remobilization strategy and the mining plans for the operation which are being implemented to make this operation competitive in the world export coal market. IntroductionIn October 1994, following a due diligence process, Fording Coal Limited purchased Coal Mountain Operations from Corbin Creek Resources, an employee group which had previously owned the mine. The purchase awarded Fording Coal Limited with 100% of the assets, and control of all the coal leases at Coal Mountain.The mine is located in southeastern British Columbia, southeast of Sparwood at the hamlet of Corbin, (Fig. 1).Rehiring of laid-off employees started in November 1994, with mining activities also recommencing in November. The coal preparation plant was restarted in December with one shift, went to two shifts in January 1995, and had four-shift, full-time operation in April 1996."

Jan 1, 1997

By B. MohammadSadeghi, S. Bakhshivash, M. Haghshenas, F. Rahimi

"Constrained groove pressing (CGP), as a severe plastic deformation (SPD) technique, is one of the applicable methods for sheet metal forming capable of producing ultra-fine grained materials (UFGMs). In CGP, processing and die design parameters can significantly affect the deformation response of sheet metal specimen. Having said this, in the present research the effects of die design variables and processing parameters (i.e. shear angle and friction) on the deformation behaviour of an Al-Mg-Si Alloy are studied thoroughly. Finite element analysis (FEA), was used to evaluate the effectiveness of mentioned parameters on the deformation homogeneity, strain distribution and pressing load variations. Also, mechanical properties of the deformed sample in term of micro-hardness was analyzed. It is observed that with increasing the shear angle, effective stress, strain and pressing load are enhanced. Moreover, by increasing the coefficient of friction, pressing load enhances. The color coded micro-hardness measurement showed a good agreement with the strain distribution obtained from FEA (higher hardness for the zones associated with higher shear plastic strain values).INTRODUCTIONWork hardening results in enhanced mechanical properties upon cycles of deformation (Hosford & Caddell, 2007). However, the formability of the processed products are affected by work hardening reducing the possibility of processing in subsequent deformation cycles. Therefore, many industrial processes cannot be performed on sheet metals to produce products with desired mechanical and physical properties (Valiev, Islamgaliev, & Alexandrov, 2000). Severe plastic deformation (SPD) is an effective grain refining technique which can impose large plastic strains through cold working on a metallic specimen (Bisadi, Rastgou, Payganeh, Zeynali, & Ghahremani, 2010). SPD techniques are mainly categorized into three types; sheet, bulk and tube forming. Among SPD sheet forming methods, Constrained Groove Pressing (CGP) (Shin, Park, Kim, & Park, 2002), Accumulative Roll Bonding (ARB) (Saito, Tsuji, Utsunomiya, Sakai, & Hong, 1998) and Repetitive Corrugation and Straightening (RCS) (Zhu, Lowe, Jiang, & Huang, 2001) possess potential applications in manufacturing industries."

Jan 1, 2016

By C. T. Morley

The steadily increasing interest in high pressure grinding rolls (HPGR) as a legitimate alternative comminution technology for hard rock applications has led to a proportional increase in the demand for trade-off studies comparing HPGR with more established approaches, typically SAG-based but including AG and stage-crushing designs. The primary trade-off is between a) the higher capital cost typically incurred with HPGR-based designs and b) the higher operating costs of the more traditional technologies. However, if, through circuit design innovation, the capital cost penalty of HPGR circuits could be eliminated or reversed, then the need for trade-off studies would diminish.

Jan 1, 2012

By C. Barnett

"The mill at Noranda Mines Limited, Geco Division in Manitouwadge, Ontario went into production in 1957 treating 3,500 tons per day of copper, zinc, silver, lead ore. It was not until 1964, however, that the zinc concentrate drying plant was constructed. In 1970, milling capacity was increased from 4,000 to 5,000 tons per day. The zinc content of the ore is quite variable so that the tonnage of zinc concentrate dried varies from 200 to 650 tons per day.The drying plant was designed to dry 25 tons of zinc concentrate, dry basis, per hour from an initial moisture of 8.5% to a final moisture of 2%. Major components were selected so that capacity could be increased to 35 tons per hour with minor modifications.The rotary dryer is a Hardinge type ""XH-12"" with a diameter of 80"" and a length of 50 feet. The all welded construction shell is 1/2 inch thick mild steel plate with 3/4"" thick reinforcing bands under the tires arranged for operation at a slope of 1/2 inch to the foot. The 3/8"" x 12"" radial flights are welded to the shell. There are no flights in the last ten feet of the shell in order to reduce dusting. This unit is driven by a 50 HP motor through a Hamilton type CD250 double reduction helical gear speed reducer. The shell speed is 5.8 RPM.The standard Peabody horizontal air heater has a rated capacity of 10,000,000 B.T.U. 's/Hr. The combustion chamber is lined with high temperature refractory brick and is air cooled. The conical outlet section of the air heater is lined with insulating fire-brick. The burner is a type AT wide range mechanical atomizer fired by a type ""CR"" gas-electric ignitor.The Bunker ""C"" fuel is supplied by a Compower duplex pumping, heating and straining unit, including tank hotwell, Powertronic oil line heating system with a 550/24 volt transformer."

Jan 1, 1972

By Yu Chen, Charlie C. Li

The application of rock bolts for the stabilisation of underground openings needs a good understanding of the response of the bolts during rock excavation. The pull-and-shear performance of two types of rock bolts—that is, the fully encapsulated rebar and the D-Bolt—has been studied both experimentally and numerically. The rock bolts were tested under a pull-and-shear load at five displacing angles (i.e., 0°, 20°, 40°, 60°, and 90°), and at the same time, the strains on the bolts were monitored during testing. The two types of rock bolts have similar loading capacities, while the loading angle has obvious influence on the deformation capacity of the D-Bolt. The ultimate total displacement of the D-Bolt decreases from 140 mm under pure pull loading to 70 mm under shearing. The displacement capacity of the rebar is not significantly influenced by the loading angle but remains at a quite low level from 29 to 53 mm. The D-Bolt yielded in a longer section the rebar bolt under pure shear. A trilinear material model was used to simulate the strain hardening behaviour of the bolt steels in the numerical code FLAC3D. The numerical results show that the axial load in the bolt decreases exponentially with the distance from the loading position for the rebar bolts, but it remains constant in the bolt sections between the anchor positions for the D-Bolts. When the bolt is subjected to a lateral load, shear stresses are created on the D-Bolt surface within a short distance from the loading position.

Jan 1, 2015

"IntroductionNOTE.-All figures on the supply and consumption of coal in Canada cited in this paper were collected and reported by the Dominion Bureau of Statistics. The friendly and efficient co-operation of the officials of the Bureau. is the foundation upon which it has been my privilege to rely in the preparation of this and two earlier papers ( 1). My thanks are due also to our own staff on the Dominion Coal Board, who spared neither time nor effort in helping to prepare this paper.STATISTICS are comparatively dull and, to many people, coal statistics are duller than most. Coal is, however, the one basic mineral upon which our whole way of life depends and it may be well if attention is drawn to this fact by an occasional statistical review of the coal position in Canada. The recent furore over the oil and gas discoveries has so obscured the basic position of coal in many minds that a little basic coal information may be useful. It is for this reason that, for the third successive year, a factual survey of the coal position is being presented.In the previous papers (1) explanations have been given of the basic considerations in the preparation of these reports and some special phases of the overall picture have been examined. For these explanations, the earlier papers may be consulted."

Jan 1, 1952

By W. G. Robinson

"MINING is one of Canada's most important industries and exploration is the life-blood of this dynamic and exciting business. The health and growth of the mining industry of tomorrow depends on the effort and thought that go into exploration today. The Members of the Geology Division of the C.I.M. are directly concerned with exploration, and it is fitting that this Division should periodically sponsor reviews of the thoughts and practices of the exploration com-munity. Accordingly, we have invited seven leading authorities to contribute papers dealing with specialized aspects of this field.Exploration is a science, or art if you will, that is constantly changing in keeping with our expanding knowledge of geology and technology. It started with the old-time prospectors who searched the wilds for exposures of ore, and made finds that developed into some of our most important mining camps. As more discoveries were made, they were able to relate certain types of deposits with particular geological conditions, laying the foundation for modern concepts of economic geology. The mapping by the early field parties lacked detail and usually served to outline the ""greenstone"" areas considered favourable for prospecting. More de-tailed studies through the years by government and company geologists led to new thoughts on the origin, emplacement and geological control of orebodies. The continuing diversity of opinion on these subjects indicates a need for further research, but each year sees an increase in our reserves of factual information."

Jan 1, 1967

By H. H. Wang

Construction safety documents regulate significant safety actions and requirements by which construction workers or employees should abide in order to secure them from occupational hazard events. Therefore, facilitating faster identification of applicable safety requirements from the documents has become an important topic in the construction safety domain. To address the need in this regard, tools and techniques have been developed and research efforts have been made. One of the research efforts is to utilize ontology, a knowledge representation and reasoning approach, as the methodology to achieve the goal of identifying applicable safety requirements. In such ontology-based researches, the development and construction of the safety concept ontology is an essential task as the concepts and the relationships between the concepts both representing key safety knowledge need to be carefully identified. In this paper, the author focuses on the safety documents without predefined concept structure and aims to address the concept and relationship identification difficulties. Specifically, the author leverages the Formal Concept Analysis (FCA) methodology, a theory of data analysis that identifies conceptual structures among data sets, to mine and analyze the documents in order to discover safety concept structure and to further assist the development of the concept ontology for the construction safety documents. The author expects the application of FCA to construction safety domain can eventually benefit the ontology-based approaches for identification of applicable safety requirements.

Aug 1, 2013

By Adrian Dance

Newmont Ghana Gold Limited?s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto- Mill projects, PTI?s methodology is termed Process Integration & Optimisation (PIO). Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit. Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended. A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI?s SmartTag? system. The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material. This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput.

Jan 1, 2012

By François Charette

High stress conditions in weak rock masses lead to large deformation and breakdown of the rock material, while stress release events in hard rock mines can lead to sudden and usually violent rock failure. Typical support systems combine various reinforcement and support mechanisms to provide the required convergence control and retainment, but results are often mitigated by failure of surface liners, shotcrete and tendons. The paper reviews differing requirements of support and reinforcement for different failure types. In addition, the mechanical performance of a new reinforcing tendon is presented and analysed in view of the field requirements. Field tests results are presented.

May 1, 2011

By G. Danko, C. Lu

"High temperature and humidity at the working negatively affect safety and health in deep and hot underground mines. It is necessary to predict during design the dynamic changes in temperature with heat and moisture emitted into the mine ventilation-thermal-humidity (VTH) system from various sources such as auto-compression, wall of strata, mining equipment and workers. Currently available mine ventilation and climate models are either furnished with a simplified, step-change-type (SCT) model for thermal solver (such as in Climsim, VnetPC, Minevent, MFire, etc), or with more advanced models to account for the “thermal history effect” (also known as thermal flywheel effect), such as in Ventsim and MULTIFLUX. The goal is to quantify the modelling error caused by the lack of variable thermal history component in the SCT model. Two models are compared: one with and one without the thermal history component in long, single airway examples with long-term climate simulations for 20 years assuming an input air temperature with daily variation. The examples illustrate the magnitude and the time-lag phase of the variation of the modelling errors with space, time and model conditions. Large errors are shown in the order of +14°C and –7°C errors, persistent for long time periods, up to 20 days in one example.INTRODUCTIONIt is important to predict the heat and humidity distributions during the design of hot and humid underground mines for the safety and health of the workers. The feasibility of extracting a rich deposit in great depth may depend on the extent of ventilation and mine climatization for maintaining an acceptable working environment. The cost of ventilation and cooling may be substantial, up to 40–50% of the total energy cost of mining (Clausen, 2017). The accuracy of model solution is important in view of the low profit margin in mine feasibility for deep and hot mines. Safety and health of the miners, the primary concerns, are therefore inherently connected to finding ever better solutions in simulation methods and ventilation control techniques."

Jan 1, 2019

By Ted Nuorivaara

The use of polymer-surfactant mixtures as foam stabilization agents is a topic that has drawn the attention of several fields but has so far not be thoroughly studied in the context of mineral froth flotation. The present work showcases a study on the impact on flotation performance of cellulose surfactant derivatives and their mixtures with commercial frothers. Bubble size and foam property measurements were run in a two-phase system along with laboratory-scale flotation experiments conducted using a porphyry copper ore from a mine in Finland. A comparative analysis on recovery, grade and flotation kinetics is presented on the products obtained using: i) a partially hydroxylated cellulose derivative (i.e. hydroxypropyl methyl cellulose; HPMC), ii) a commercial polyglycol-ester frother (Nasfroth240; NF240), and iii) mixtures of these two. The results show that using frothers with a total concentration of 30 ppm, the HPMC-NF240 mixtures provide advantages in terms of Cu recovery, (i.e., up to 95%), compared to the use of either NF240 (ca. 76%) or HPMC alone (ca. 1%). Interestingly, only a small proportion of HPMC mixed with NF240 was sufficient to produce a measurable increase in recovery. This improved performance was attributed to a synergistic effect of the polymer-surfactant mixture which further reduced the bubble sizes in a two-phase system compared to that of NF240. The present work offers a further step into understanding the phenomena taking place when a short chained surfactant is either substituted or mixed with a cellulose derivative, offering potential ways of exploiting this behavior for the enrichment of minerals. INTRODUCTION Froth flotation has been the predominant technology used to beneficiate sulfidic copper minerals such as chalcopyrite ever since it was invented in the late 19th century. The reason for the domination of flotation technology lies behind its versatility in selective separation as well as relatively cheap operational costs (Wills & Finch 2015). Even though flotation of sulfidic copper minerals is moderately well understood based on the broad research work done around the subject (e.g., Albijanic et al., 2015, Bournival et al., 2017, Wang et al., 2015, Mikhlin et al., 2015, to cite only a few), the modern era presents new challenges to the primary raw material industry, including questions regarding sustainability of mining operations accompanied by a need to improve the process efficiencies due to declining ore grades (Edraki et al., 2014).

Jan 1, 2019

By K. Kryst, K. Elkayar

The increasing need to process lower grade contaminated copper concentrates and simultaneously produce higher purity copper cathodes necessitates a more diligent control in the electrorefining process. Ion exchange processes can be a powerful tool in controlling electrolyte impurities to ensure trouble free operation within the tankhouse and to help maintain cathode purity. In addition, some impurities can be recovered as a value added product. The use of a short bed ion exchange process provides a unique opportunity for impurity management in copper refineries. Several metals are discussed in this paper, including Sb, Bi, As and Ni and their methods of control and recovery within the copper electrolyte circuit. INTRODUCTION To produce a high purity copper product by electro-refining a copper electrolyte, it is important to control the concentration of impurities such as arsenic (As), bismuth (Bi), antimony (Sb), and nickel (Ni). These impurities are introduced into the electrolyte from the copper anode and can affect the copper product and the production operation. The presence of As in the copper product results in a lower electric conductivity and reduced workability of the copper. High levels of Bi in the electrolyte will result in a copper cathode product containing Bi. High Sb concentration will cause undesired floating slimes. A variety of methods have been developed to control the level of these impurities in the copper electrolyte including precipitation, liquid extraction, and ion exchange. These impurities can be recovered and used. This paper discusses novel methods that utilize short bed ion exchange technology to control these impurities. Also, the use of ion exchange to recover acid from the liberator cells bleed for reuse in the tankhouse is reviewed. SHORT BED ION EXCHANGE Short bed ion exchange technology has been employed extensively in the metal finishing industries for over forty years. Unlike conventional ion exchange, short beds are fixed beds without freeboard space. The application of short bed technology results in significant benefits when compared to conventional ion exchange. The resin used in this technology has a significantly smaller diameter than conventional ion exchange resin. As a result of the smaller resin size, exchange kinetics improves dramatically. This facilitates operation at higher flow rates and the use of smaller beds with a small mass transfer zone length. Smaller beds are especially important for applications that use chelating resins due to the high cost of the resin.

Jan 1, 2019

By J. A. Haskin

The Engineering Department at Flin Flon has the following responsibilities: 1. Underground Surveying. 2. Open-Pit Surveying and Supervision of Blasting. 3. Mine Geology and Examination of Prospects. 4. Design of Plant Additions and Improvements. 5. Miscellaneous Field W ork, Reports, etc. The entire surface plant, as well as the underground workings, are located by co-ordinates based on a triangulation system covering an area approximately one mile long by one-half mile wide. The origin of this system and one end of the base-line is the southwest corner of Township 67, Range 29, west of the Principal Meridian. The bearing of the base-line was determined from the township boundary, which runs true north, so that all other bearings are almost astronomical. This is a great convenience when our surveys must be tied to mineral claims, rights-of-way, and land subdivisions. As the base-line extends across Flin Flon lake, its measurement across smooth ice was simple and accurate. The length, slightly over 1,600 feet, has been adjusted for the temperature and tension of the standard tapes used and checked sufficiently to ensure a maximum error of 1 : 15,000. Each angle was repeated ten times, but as no special refinements were used, errors of as much as four or five seconds are possible. The elevation of the origin of the triangulation system was approximately 1,050 feet above sea level. The use of this true elevation in our surveys would have resulted in negative elevations underground as soon as the mine reached a depth greater than 1,050 feet. To avoid this complication we therefore added 4,000 feet to this elevation. The collar of the Main shaft, for example, which is actually 1,072 feet above sea level, appears in our records as at elevation 5,072. Underground surveying, which follows standard practice, is done by two mine surveyors who share three helpers. The meridian is taken underground from two wires hung in either of the two vertical shafts.

Jan 1, 1935

By J. -M. Lalancette, D. Lemieux, C. Chouinard

"A gold bearing concentrate containing 107 g/T of gold, 9.3% copper and 706 ppm of mercury was processed at the demonstration scale for the extraction of gold and copper using a cyanide free process. The concentrate was generated through flotation to upgrade the gold and copper grade, but also showed contamination with mercury. This concentrate was submitted to the DST process demonstration plant. The concentrate was first oxidized using a fluidized bed to produce a calcine. The mercury was volatilized during the oxidation stage with an efficiency higher than 98%. The mercury was condensed and removed from the sulfuric acid using a thiosulphate process. Copper was extracted from the calcine as copper sulphate using diluted sulfuric acid. The solid remaining after acid leaching was submitted to the DST chlorination process for gold extraction. Under optimized conditions, a gold extraction of 97.3% was achieved in the chlorination reactor. Gold was recovered from the pregnant brine by precipitation on silica using a DST proprietary process.INTRODUCTION Dundee Sustainable Technologies Inc. (DST) offers proprietary metallurgical processes for the treatment of material from the mining industry. DST processes enable the extraction of precious metals and for the removal and stabilization of contaminants, such as arsenic, from ores and concentrates. DST provides environmentally-friendly, viable and efficient processes, capable of handling complex and refractory ores which cannot be processed with conventional approaches due to metallurgical issues or environmental considerations. Several mining jurisdictions around the world have banned or restricted the use of cyanide. DST has developed a closed loop chlorination process as an alternative to the conventional cyanidation process for the extraction of precious metals from minerals. The tailings from the process are inert from toxic substances such as cyanide and organic compounds, are sulphide depleted which means they do not generate acid, and thus, meet and/or exceed environmental norms. The process has demonstrated excellent gold recoveries within a fraction of the time needed for cyanidation to obtain similar results. Moreover, the closed loop process does not generate any liquid effluent and does not consume much water: it only requires a water make-up to compensate for moisture leaving with the tailings and by-products, and seawater may be used. The improved environmental footprint of the DST process has been certified by the Environment Technology Validation program (ETV) which provides an independent evaluation of the performance claims of innovative technologies."

Jan 1, 2017

By D. DeGagne, E. De Souza, J. F. Archibald

This paper describes the potential use of anew agent material for backfill consolidation, ground waste glass, to be used as partial replacement of Portland cement fractions within backfill. Significant fractions of commercial and residential silica glass production is currently utilized as waste landfill and must be disposed of at high cost and with no foreseeable environ-mental benefit. This paper also demonstrates that waste glass materials could be effectively recycled as backfill additives, and that a significant, large and stable source of additive supply, currently land filled, can be developed. This new application will generate added value for such materials, serve to promote positive environ-mental stewardship and satisfy engineering sup-port requirements in mines.

Jan 1, 1997