Search Documents

By M. Vallée

Several reviews of mineral project performance in the past 35 years indicate a pattern of occasional, but recurrent, mining project failures due to shortcomings in geological information and estimation, mineral processing and metallurgical testing, feasibility study objectives and requirements, and project start-up methods. A commitment to quality assurance and continuous improvement methods and to obtaining “ENOUGH DATA, OF APPROPRIATE QUALITY” is essential. Recent international and Canadian proposals for mineral resource and ore reserve definitions have taken a nonprescriptive stance that will undermine the formulation of requirements, guidelines and industry standards for efficient deposit delineation and estimation, and for the determination of project feasibility. To help reduce problems, every feasibility study supporting a mine development and production decision should be based on objectives and methods adequate to reach completion targets similar to the bankers’, as a good business target for a profitable project. In a resource/reserve system, the use of reserve should be restricted to a project that meets required technical, economic and legal feasibility requirements for successful project implementation, and the definitions of these categories should provide explicit limits. Current shortcomings will limit the ability of the Qualified Person to provide “adequate professional practice,” fulfill his/her professional responsibilities to his employer or client and provide adequate information to the investing public. We must take advantage of present opportunities for Setting New Standards for the new Millennium.

Jan 1, 2000

By D. W. McDonald

Coal mining and railway transportation are so closely en-twined and so dependent one upon the other that the failure of one would mean the total collapse of the other. With this indisputable fact in mind, there is no doubt that the operator of each is deeply interested in the other's success. Railway transportation began at the mouth of a coal mine. The first railway car was the English coal-wagon, a crude box on four wooden trowlets, running on wooden rails and holding 1,600 pounds. This was operated by gravity or horse-power in England to convey coal from the mines to the rivers. The first coal-cars used on Nova Scotia railways were of 4 tons capacity with side doors and "V" shaped centres. Then followed flat-bottom, 4-ton cars that operated on tipples, the car bei.ng held in tipple by a chain passing over the top and fastened on either side. Next came the 6-ton car with drop-bottoms, then the 10, 15, 30-ton cars, and now the modern 50 and 100-ton steel cars, equipped with automatic couplers, brakes, and rachet dumping device. Contrast the first coal-car with a modern luxurious pull-man or a I 00-ton coal and ore car, and you have a record of progress in railway transportation. The development of the steam locomotive was no doubt the greatest factor in this progress, but let us not forget that the foundation of all industrial development was and is coal. and that development in mining and railway transportation should keep abreast.

Jan 1, 1924

By W. S. Dyer

The Minto coal basin lies in the central part of the province of New Brunswick, near the head of Grand Lake. The village of Minto which is the centre of mining activity of the district, lies about 35 miles east of Fredericton and somewhat greater distances to the north and west of the cities of St. John and Moncton respectively. Although coal has been mined in the basin for a number of years, it was not until recently that the production became sufficient to warrant a thorough geological investigation. The summer of 1922 was spent, in accordance with in structions from the Director of the Geological Survey, in making a detailed study of the geology and coal resources of the Minto coal basin, which is covered by the Minto and Chipman map sheets, each embracing an area of 200 square miles. The present paper is a short outline of the principal results obtained in the field. The writer wishes to acknowledge the assistance cheerfully given him by the managers and officials of the various companies operating in Minto. He wishes especially to thank Mr. W. B. Evans, Manager of the Rothwell Coal Company, for assistance in the collection of fossils and for the generous supply of information relative to the early history of the coal field.

Jan 1, 1924

By A. Fawceit, B. C. Dyer

"The basis of the tomographic velocity imaging technique is briefly described and an application of the method to detect and image a cross-section through a chromite pod is presented. Using the chromite application as an example, the relative costs of tomographic data acquisition and processing are compared with those of diamond drilling to obtain similar resolution. A number of different tomographic survey configurations and the potential role of the method in surface and underground exploration are discussed.IntroductionThe technique of seismic tomography has been most widely applied in oil industry exploration, nuclear waste disposal, civil engineering site investigations and in the assessment of the condition of mass concrete structures. Although model studies had indicated that tomography would be a useful tool in mineral exploration, relatively few applications have been reported.Essentially the method relies on the determination of the speed with which sound travels through a region within a cross-section of the earth or large body. The speed of sound is determined by the physical characteristics of the medium through which it is passing. In geophysics the speed of sound is generally referred to as the seismic velocity. Due to variations in the formations of different rocks the seismic velocity will vary and so can be used to map geological boundaries"

Jan 1, 1994

By Fred W. Snow

THE mines of the Consolidated Copper and Sulphur Company, consisting of the Eust1s, the Albert, and the Capel mines, are situated w Ascot township, Quebec, about ten miles southeast of Sherbrooke, on the main line of the Quebec Central railway. Of these mines, only the Eustis is now producing, and it has been operated almost continuously for the past seventy years. Mining methods have been improved in recent years but are still old fashioned when compared with those employed in more modern and up-to-date mines. The ore is of milling grade and is mined for its copper and sulphur con-tent. Silver is present in small quantity, together with a trace of gold. The ore is mined by the shrinkage stope method. Pillars are frequently left as supports for the hanging-wall to prevent serious dilution of the ore and are sometimes recovered after the ore is drawn from the stope. Occasionally, small blacks of ore in close proximity to the shaft are mined by a cut-and-fill method. HISTORY ALBERT AND CAPEL MINES: The Albert and the Capel mines, originally known as the Capelton mine, were discovered in 1863 by George Capel (1). By the end of 1866 the Albert shaft had been sunk to a depth of 121 feet on an incline of about 30 degrees where a vein five feet thick was encountered. In 1879, these mines passed into the hands of G. H. Nichols and Company, by whom they were operated practically continuously until 1907. When mining operations ceased in that year, the shafts had reached depths on the incline of approximately 2,300 feet and 1,000 feet, respectively. These mines have been allowed to cave and fill with water and have been inaccessible for many years.

Jan 1, 1936

Who is CIBC? ? Canadian Imperial Bank of Commerce (?CIBC?) is a leading North American financial institution. ? Total Assets: US$315 billion ? Market Capitalization: US$29 billion ? CIBC comprises three strategic business lines: ? CIBC Retail Bank ? CIBC Wealth Management ? CIBC Wholesale Bank ? CIBC Wholesale Bank is a leading North American investment bank with niche capabilities in Asia, Australia & Europe. ? 1,000 + employees around the world ? Product range includes: Mergers & Acquisitions advisory and financing, Equity and Debt issues, Merchant Banking and Strategic Lending ? CIBC is ranked as the #1 investment bank in Canada across most of its key products and industries ? #1 Equity Underwriter in Canada ? #1 Mergers & Acquisitions Advisor in Canada

May 1, 2010

By D. Kalumba, S. Jjuuko

"Thin Spray-on Liners resist relative small deformations (< 1 mm) between rock blocks or fragments in terms of a combination of shear, adhesive and tensile-bond strengths. Shear-bond strength addresses the ability of a thin liner to resist stresses that act parallel to the rock-liner interface. Therefore quantification of shear-bond strength is essential in the formulation of design standards and requirements for Thin Spray-on Liners. In this paper Thin Spray-on Liner support mechanisms are reviewed. In addition previous methods of Thin Spray-on Liner shear-bond testing are discussed. The paper also explains the research being carried out at the University of Cape Town to investigate the effect of different parameters on the shear-bond strength.INTRODUCTIONRock surface support is widely used to combat rockfalls and resulting injuries and fatalities in the vicinity of active faces (Potvin, 2002), where workers spend most of their time (Adams & Baker, 2002; Potvin, 2002; Lacerda, 2004). The conventional (traditional) surface support systems in underground rock support include passive methods such as mesh and lacing and active methods such as shotcrete. However, rockfall sources between 1990 and 2000 in Nevada gold mines showed a steady increase in rockfall injury associated with mesh support as shown in Figure 1 (Lacerda, 2004). The conventional methods also negatively impact the mining operations with regards to costs, logistics and mining cycle times due to large material volumes (Tannant, 2001; Ozturk & Tannant, 2010; Ferreira, 2012). Therefore, these systems need to be substituted, with enhanced methods, in order to realize the business target of the mining industry of providing the planned return on investment made without harm and within budget."

Jan 1, 2015

By W. Andrew Falls

Although we have yet to reach the midway point in the decade, the copper concentrate market has already witnessed some of the most volatile swings in history, moving from record high treatment and refining charges in 1991-92 to historic lows, in real terms, during the past year. What has been the cause for such volatility? By and large the swings can be attributed to factors of supply and demand in the "custom" copper concentrate market. For example, two relatively recent events which had a major impact on the supply-demand balance were the shutdown of the Bougainville copper mine in Papua New Guinea in 1989 due to rebel insurgency and the startup of the La Escondida mine in Chile in 1992. The first event, threw a balanced to slightly surplus concentrate market into a substantial deficit, forcing treatment terms down as smelters, caught short by the loss of concentrate supplies scrambled to cover their positions. The second event, brought over 300,000 mt per year of new copper in concentrate to the market, more than reversing the losses from the Bougainville shutdown. In combination with other additions to mine capacity via new mines or expansions, the custom concentrate market moved into a huge oversupply in 1991-92 and many mines found themselves unable to place uncommitted tonnage. But even this event was quickly overcome by the use of underutilized capacity at non-traditional buyers, such as those in the C.I.S., Zambia, or those which were not traditionally buyers of custom materials. All of this has happened in the space of five short years, a mere snapshot in the history of the market. I'll return to these points a little further on, but first I would like to review the fundamentals which govern the copper concentrate market.

Jan 1, 1995

By Harold N. Miller

Lost time and services caused by electrical equipment breakdown or cable faults can often be substantially reduced by the use of direct-current high-voltage testing as a maintenance tool. This paper discusses the relative merits of alternating-current versus direct-current testing, pointing out the advantages in size and cost of equipment and more definitive results achieved through the use of D.C. General principles of direct-current high-volt-age testing, types of testing, methods of performing the actual test and interpreting the results are explained. ?The value of insulation resistance measurements and their relationship to high-voltage testing is discussed. Pinpointing the physical location of a cable defect using a fault locator or thumper is described. Reference is made to several organizations that have effected considerable savings with high-voltage test programs. Introduction T HE past decades have seen great advances in the field of electrical power distribution and application. Motor generators, power-operated equipment, cables, etc., have all gone through various stages of improvement both in efficiency and reliability. Un-fortunately, however, power failures and equipment breakdown still occur -frequently with disastrous effects in loss of time,

Jan 1, 1965

By T. Nagasaka, T. Miki

Suppression of CO2 and waste such as slags discharged from iron- and steelmaking processes are some of the typical major issues for the protection of global environment and sustainable growth of steelmaking industry. Utilization of active phytoplankton growth will be one of the best options to stabilize and suppress carbon dioxide at high-efficiency. Inorganic minerals such as C, 0, N, Si, P and Fe are necessary for phytoplankton multiplication. It is crucial for supply of nutrition into seawater effectively for phytoplankton multiplication to understand the dissolution behavior of some elements from steelmaking slags into seawater. The morphology of the precipitated phases in steelmaking slags during cooling period was investigated in the present work. The dissolution behavior of some elements from steelmaking slags into artificial seawater has also been studied. The effect of nutrient dissolved into seawater on phytoplankton multiplication, some examples of marine structure made from steelmaking slag, and estimation of CO2 fixation amount by marine phytoplankton are also discussed.

Jan 1, 2004

By W. A. Alexander

Introduction In the course of a programme of research on beryllium in progress in these laboratories, knowledge of the recrystallization temperature became necessary. As the information is not available in the literature, the determination of this temperature for metallic beryllium was undertaken. By the reduction of grain size through working and recrystallization and the probable simultaneous induction of preferred orientation, it was hoped to improve the working properties of beryllium at lower temperatures. The recrystallization temperature is usually determined by observing the lowest temperature of annealing at which new crystals are formed in severely cold-worked metal or alloys. This temperature is profoundly influenced by the following factors: the purity of the metal, in the case of an element, or the composition of the alloy; the degree of straining or working; the temperature of straining; the original grain size; and the time held at the annealing temperature. The observed temperature is lowered by higher purity, more severe straining, lower temperature of working, smaller original grain size, and longer time of annealing. Beryllium presents special difficulties in that the percent elongation in tension is effectively zero, so that ordinary squeezing or rolling was not possible. A possible means of straining was suggested by the fact that indentation hardness tests could be made. It was known from earlier work that the metal could be worked at elevated temperatures, so that working at the lowest feasible temperature and quenching might also be a means of producing strain. The purity of the metal is also a point of some uncertainty in the case of beryllium. Losano has prepared 99.96% Be which appears to be the best reported. Distilled metal used in the present work approached this purity. However, by analogy with other metals, residual impurities may have a pronounced effect on the recrystallization. Further purification of beryllium would evidently entail considerable difficulties due to the highly reactive nature of the metal, and was not attempted.

Jan 1, 1947

By L. A. Jameson, J. Awmack, P. J. Lind

"Peñasquito is a polymetallic deposit containing gold, silver, lead, and zinc. The operation is currently the largest producer of gold in Mexico. Over the next few years, the process flowsheet will be expanded beyond the flotation of lead and zinc to include flotation of pyrite from zinc tails and subsequent leaching of the pyrite concentrate. This paper outlines mineralogical leach characterization that has been carried out to improve the understanding of the complex hosting of gold and silver minerals in the ore. Organic carbon that is present in the ore can have an impact on flotation and leaching. Mineralogical techniques used to characterize this deleterious component of the ore are introduced.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas as shown in Figure 1. Peñasquito has been in operation since 2009 and is currently Mexico’s largest gold mine. Mining is carried out by open-pit methods, with oxide ore proceeding to a heap leach facility and sulfide ore treated in the sulfide processing plant.The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 450,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead, and 263 million lb of contained zinc in lead and zinc concentrates. GEOLOGY The Peñasquito deposit is hosted in and adjacent to two breccia pipes; Peñasco and Breccia Azul. The two breccia pipes are branches of a larger intrusive-related complex, which is hosted in the sedimentary Caracol formation as illustrated in Figure 2. The regional geology is dominated by Mesozoic sedimentary rocks which comprise a thick series of marine sediments deposited during the Jurassic and Cretaceous periods. A 2 km thick sequence of carbonaceous and calcareous siltstones and interbedded sandstones is underlain by a 1.5 to 2 km thick limestone sequence (Goldcorp Inc., 2015)."

Jan 1, 2017

By F. Shi

The JKRBT (JK Rotary Breakage Tester) is a newly developed impact breakage testing device for rapid ore breakage characterisation, and has recently been commercialised after a three year comprehensive validation study, involving five major mining companies and six industrialised JKRBT units deployed worldwide. Comparisons of breakage mechanisms and characterisation data between the JKRBT and the Drop Weight Tester (DWT) indicate that, despite the differences in the breakage modes, the JKRBT can provide statistically similar A*b parameters, by using a data reduction procedure which takes into account the difference in the number of contact points, strain rate and potential for secondary breakage. Feedback from the validation sponsors has indicated higher productivity and better repeatability of the JKRBT compared with the DWT. This better precision, combined with the JKRBT’s wider particle size capability and wider specific energy range, provide a more powerful tool, ideally suited to rapid mapping of ore hardness in geometallurgical and comminution applications.

Jan 1, 2012

By Lisa L. Van Loon, Neil R. Banerjee

Canada is a world leader in uranium exploration, but many deposits are located in remote regions making exploration targeting challenging. Novel approaches are needed to detect the presence of large-scale ore-forming systems and to vector toward mineralization. Boron is commonly used as a key pathfinder element associated with sandstone/unconformity-hosted and basement-hosted uranium deposits in the Athabasca Basin, but the genetic relationship remains uncertain. Alteration assemblages containing boron geochemical anomalies are commonly spatially-associated with – and possibly coeval with – uranium mineralization. Boron is commonly found in tourmaline minerals but in some portions of ore deposits the host mineral for the anomalous boron remains cryptic. Boron coordination chemistry within alteration haloes can better constrain boron host mineralogy, provide insight into the nature of the boron-uranium relationship, and thus has the potential to better constrain targets for exploration. Synchrotron-source X-ray absorption near-edge structure (XANES) spectroscopy is a direct, element-specific analysis that identifies boron coordinated in both trigonally- (BO3) and tetrahedrally-coordinated (BO4) forms. This makes XANES uniquely suited for identifying the geochemical hosts for boron that may be related to hydrothermal ore forming processes. XANES spectroscopy was conducted on whole-rock assay powders from uranium deposits across the Athabasca basin containing boron concentrations ranging from <10 ppm to >10,000 ppm. XANES directly identifies the relative amount of trigonally- (BO3) and tetrahedrally-coordinated (BO4) boron in these complex mineralogical mixtures. Our work suggests a link between boron and uranium that is likely related to the unique physiochemical characteristics of ore bearing fluids that may provide a unique vector to mineralization.

Jan 1, 2020

By M. Cossette, P. C. A?tcin

At present there is considerable confusion in the asbestos industry with regard to density and porosity measurements of asbestos. In order to clarify the situation, various notions of porosity and density are defined by means of simple schemes and clear symbols are proposed to denote them. An experimental procedure is then preposed and outlined, which is based upon Archimedes' principle. Experimental conditions at each stage of the method are explained clearly in order to minimize the opportunity for errors. Finally, the results of a study on the porosity and density of asbestos minerals having various characteristics are presented.

Jan 1, 1972

By M. Somppi, Z. Yamak

"Gold producers invest significant effort in mining, processing, and creating an intermediate gold doré product. Nonetheless, equal effort should be extended to the final handling and processing of the doré bar, and managing the high-purity gold produced at the fine-gold toll refiner. This detailed attention to bullion handling and refining provides rigor and confidence that the mine site is achieving, through fair and controlled methodology, the most appropriate value for the final product. With the above in mind, the following study explores the importance of preparing a set of site best-practices for bullion handling and specifically, detailing the peculiarities of sampling methodologies and the impact on assays.INTRODUCTION Gold and silver handling practices are common place at mine sites and refineries. The practices include but are not limited to smelting, ingot casting, weighing practices, and secure transportation. Proper handling and processing of the bullion material ensures that the mine site is achieving the true value of the final product. Various handling aspects can critically impact the perceived value of the bullion. A few of these particulars include weight tracking, scale recertification and calibration, refining and melting practices, melt temperature measurement, sampling, pouring, bar cleaning, furnace technology and crucible selection, and assaying. Nevertheless, this report discusses and focuses on the importance of proper sampling and molten-metal temperature measurement and their potential impact on the final doré bar value. Refining or re-melting operations achieve a proper measure of the precious metal content of its bullion when the sample accurately represents the whole bar. At first this task appears seemly straightforward, however, taking a representative sample can be challenging and is also one of the most important tasks for valuing gold during the settlement stage at the precious metal refinery. Various bullion sampling methodologies exist; including: dip sampling, granulation, drilling, cutting, and vacuum pin sampling. The Royal Canadian Mint (2009) indicated in their technical review of refinery operations that pin sampling is one of the best methods for cases where representative sampling and accuracy are required, e.g. to determine the payable metal content. Pin sampling consists of inserting a sealed glass vacuum tube (Figure 1) into the molten metal; when the molten metal contacts a purposely-designed weak portion of the glass, the seal breaks and the metal is suctioned into the hollow centre (Figure 2)."

Jan 1, 2018

By N. Novikov, M. Jastrzebski, N. Kryzhanovskaya, D. Shevchenko, I. Kapran, N. V. Novikov, T. Koehler, B. Zaporozhets

"The PFK FeNi Smelter was re-commissioned by Solway Resources in 2002, ending a long period of economic decline in the adjacent town. In 2009 Hatch was retained to design, supply and install a custom furnace crucible that would accommodate a capacity increase from 34 MW to 40 MW and increase campaign life through binding and cooling technologies, as part of ongoing improvement efforts. The involvement of PFK personnel was critical to the successful integration of the new furnace technology with the existing process and operational practice. The furnace upgrade project was completed in 18 months during 2010 – 2011. Since start-up, the furnace has exceeded production expectations, operating successfully at 42 MW.INTRODUCTIONAfter ceasing operations in the 1990’s, the Pobuzhsky Ferronickel Combine (PFK), located in central Ukraine, was stripped of useful equipment and deteriorated while dormant. The surrounding town experienced a period of economic decline throughout the 1990’s. Solway Industries purchased the complex in 2002 and began a systematic incremental program to re-commission the smelter using both local expertise and specialists from other parts of the former Soviet Union. This led to the re-birth of PFK as a successful toll-smelting complex, and a renaissance for the surrounding economy.As part of the continuing improvement program, PFK approached Hatch in 2009 to study the possibility of a capacity expansion from 34 MW to 40 MW. It was decided, based on the results of the study, to design and install a custom furnace crucible integrating the unique PFK FeNi process with modern Hatch furnace technology. This novel approach had many benefits, including: maximum re-use of existing furnace components (off-gas, feed equipment and transformers), minimal impact on upstream and downstream equipment and building structure, and the retention of a familiar operating regime. The latter was a key factor in the success of the project, as it allowed the extensive operating expertise of the PFK staff to remain highly relevant to the upgraded furnace. This led to minimized capital investment, a rapid start-up and no significant operational challenges switching over to the new equipment incorporating Hatch furnace technology."

Jan 1, 2012

By K. Sakaguchi, T. Yokoyama

"In-situ rock stress measurement was carried out in the Kamaishi mine of Iwate Prefecture to quantify the variation of the shallow crustal stress field associated with the 2011 Tohoku-oki earthquake. Stress measurement was conducted by the Compact Conical ended Borehole Overcoring (CCBO) technique, which is one of the stress relief method. The CCBO technique is the one of the suggested method of ISRM. Measurement period is from 1991 to 2014. Main results obtained in this study can be summarized as follows.The direction of the maximum principal stress did not change much before and after the earthquake. However, the directions of the intermediate principal stress and the minimum principal stress of one year after the earthquake changed from those of before earthquake. Namely, the direction of intermediate principal stress was East-West horizontally, and the direction of minimum principal stress was vertically. This state of stress is reverse fault type and was maintained for three years after the earthquake.The magnitudes of principal stresses and the vertical stress of one year after the earthquake became more than the double before the earthquake. However, the magnitudes of the maximum principal of two year after the earthquake became smaller comparing with those of one year after the earthquake. Furthermore, the magnitudes of the intermediate principal stress and the minimum principal stress of two year after the earthquake became almost same as those before earthquake, and the vertical stress of two year after the earthquake became almost equal with the overburden pressure. And the magnitudes of three principal stresses of three year after the earthquake became the same level before the earthquake."

Jan 1, 2015

By Mel Torrie

1 Want access to low level vehicle data so 3rd party apps can be applied as desired 2 Hardware Agnostic (COTS plug and play) 3 Common/Open protocols that facilitate integration and the coexistence of a variety of applications on a variety of equipment 4 Minimum computer hardware footprint 5 Technology Independence (including comm. backbone)

May 1, 2013

By M. R. Shadnam

This contribution provides an assessment of research and development efforts to optimize SOx, NOx and mercury capture in flue gas. Coa, characteristics and combustion conditions in a power plant have an impact on the types and concentration of flue gas pollutants. These factors can also affect the amount of pollutant removed. This contribution would also provide a comparative study of the technologies that holistically aim remova, of SOx, NOx and mercury altogether in coal-fired power plants. A portion of this contribution provides background information on regulatory drivers.

Jan 1, 2010