Search Documents

By R. C. Gilmore, J. F. Brune

"Pulverized limestone rock dust used in United States underground coal mines to prevent and suppress coal dust explosions must easily disperse by forces of a methane or coal dust explosion. Moisture in the mine environment causes caking of the dust. Colorado School of Mines researchers performed dispersibility tests in a full-size explosion test drift. Tests included conventional, hydrophobized, and rock dust approved for German mines. Conventional and German standard rock dust products partially agglomerate, which may not be effective in suppressing a coal dust explosion, while hydrophobic rock dust retains better dispersibility.INTRODUCTIONA coal dust explosion devastated the Upper Big Branch mine in 2010 resulting in the death of 29 miners, the worst mining accident in the United States since 1972. The explosion propagated through approximately 65 km of active mine workings, but was extinguished in areas that had been properly rock dusted (Page, 2011). Researchers have long studied and established the ability of inert limestone rock dust to suppress coal dust explosions, see Richmond et al. (1975), Cybulski (1975), and Sapko et al. (2000).To be effective, rock dust must contribute to a total inert content of > 80% by weight and 100% of rock dust particles must pass through an 850 µm sieve, while 70% of the rock dust must be finer than 74 µm. This is established in US regulations 30 CFR §75.2. Dry rock dust is a nuisance that prevents mining work downwind from rock dusting activities. To overcome this problem, dust manufacturers have proposed applying the rock dust as a wet slurry or foam. After drying, manufacturers expected the slurry or foam-applied dust to have the same explosion suppression capabilities as dry-applied rock dust.Researchers at the Colorado School of Mines (CSM) designed and built a full-scale, underground Explosion Test Facility (ETF) at the CSM Edgar Experimental Mine in Idaho Springs, Colorado about 20 miles west of the CSM Golden, Colorado campus. To disperse the different rock dust products, researchers produced an air pressure pulse using a mesh array of PETN detonation cord. This method is simpler, more reproducible and safer than other methods considered, including methane-air explosions and a compressed air cannon. The detonation cord blasts produce a wind velocity of 30 to 50 m/s, the minimum velocity at which coal dust explosions can propagate, based on research by Nagy (1981) and Cybulski (1975)."

Jan 1, 2019

M INE production requires the coordination of the talents of men and the use of equipment. Mine operators maintain a continual surveillance of equipment, looking for improvements and modifications that will benefit them. Few give similar attention to the advances made in the education of mining engineers since they themselves graduated. That is not surprising. Education lacks the advertising budget available to manufacturers. A modification to improve a mechanical contrivance is advertised, and an advertiser's press releases get attention by publishers. The whole program for mining engineering education could be revolutionized and no one, except a few professors, would know about it. The Canadian Institute of Mining and Metallurgy's newly established General Commit-tee on Education can improve that situation. Nine groups of engineers in Canadian universities are trying to give undergraduates an education that will make them useful to the mineral industry as mining engineers. The tabulation offered here (Table I) is an analysis of the distribution of the undergraduate-teacher contact time.

Jan 1, 1963

Real Time Monitoring of Cemented Paste Backfill Introduction Methods ?how to instrument a Long Hole stope Key Results from 2 case studies: barricade pressures and displacement, in-stope pressures Importance of Real Time Monitoring How binder, rise rate, cement content affect fence pressures

May 1, 2010

By Mark W. Booth

THIS paper deals with the subject of inbye power as the mechanical . engineer sees it, and invites discussion, particularly from the electrical engineer. At the outset, it will be necessary to clear the ground a little by some definite statements. In this question of compressed air versus electricity for the transmission of power and driving of machinery in underground workings, we must see that there are definite fields that compressed air on the one hand, and electricity on the other, can fill to much greater advantage than the other, and in which there can be little or no direct competition, at least for the present. It is under conditions where these fields overlap, and as to where the line must be drawn between the two, that the respective merits of each must be considered. Steam was the first means used to transmit power from the surface of a mine to drive underground machinery, and so long as distances were short and means possible to ensure fairly efficient use of the steam, and where the fire hazard was not in evidence, it gave fairly efficient service. I have in mind an instance during my own connection with the mines-a duplex pump at the shaft bottom at Princess colliery, driven by steam, and which used the steam compound and condensing; and, but for the mechanical difficulties, it was a not inefficient proposition. The steam was taken direct from the surface boiler-plant through a line down the shaft, and used directly at the pump, being in effect a straight conversion from coal to steam to work done. It was the mechanical arrangement, and failure of the pump in that direction, that led to its removal and replacement by something better in the way of an electrically driven turbine pump. Given modern mechanical arrangements, such as a steam-turbine drive on a high-speed turbine pump, and all other parts made in accordance with best practice in the art of steam generation and use, a steam-driven unit fully as economical would have been obtained. But the central electric supply station, and all that that means or promises (not always the same), turned the scale against steam.

Jan 1, 1936

By N. Pajunen, R. Mäkikoskela

"The current state of environment has been achieved by acting linearly. At the same time, we know that transition towards circular economy cannot be made the same way that we have used to, trusting only a market economy and economic growth. Environmental improvements have been promoted, some progress has been made, but major steps towards sustainability have not been taken. Industry is now facing significant change, from process related environmental thinking to product-based environmental thinking.Engineers make decisions which have lifelong influence and even longer on environment and society. Material engineers in case of saving natural resources and increasing material cycle, have an important role to play in the transition towards sustainability. Best knowledge of minerals and materials is in the material development phase. If we want to increase the cycle of different materials, it is vital to make decisions towards circular economy in early phase of product´s life cycle.The target of this study is to promote circular economy; to increase material efficiency; to save natural resources; and to extend product lifecycles in process industry via product design and material development. In this study we have a new kind of cooperation. We combine two disciplines, engineering science and fine arts. We promote sustainability via breaking out the silos. We bring the cyclic artistic thinking into engineering science and environmental research. The new research combination makes the existing information visible in a new way, and it will change attitudes and ways to act by means other than traditional linear rationality.We have tested the new working method via the industrial case study with the chosen product: the sandwich panel of construction industry. The target of the study was to create something new from the chosen product with artistic thinking. The working method will be presented in this paper."

Jan 1, 2016

By Limao Zhang

This paper presents a BIM-based Risk Identification Expert System (B-RIES) for metro construction, composed of three main built-in subsystems: BIM extraction, knowledge base management, and risk identification subsystems. The engineering parameter information related to risk factors is extracted from the BIM of a specific project where the IFC standard plays a bridge role between the BIM data and metro construction safety risks. An integrated knowledge base, consisting of fact base, rule base and case base, is established to systematize the fragmented explicit and tacit knowledge. A hybrid inference approach, with case-based reasoning and rule-based reasoning included, is developed to improve the flexibility and comprehensiveness of the system reasoning capacity. During the safety risk identification process, B-RIES is able to improve the inefficiencies in engineering information extraction, reduce the dependence on domain experts, and facilitate knowledge sharing and communication among dispersed clients and domain experts. A typical safety hazard identification in the Mingdu station, located in the Wuhan Metro Line Two, is presented in a case study. The results demonstrate the feasibility of B-RIES, and its application potential. B-RIES can be used as a decision support tool to provide guidelines for safety management in metro construction, and thus increase the likelihood of a successful project in a complex environment.

Aug 1, 2013

By J. T. Kalala

The High Pressure Grinding Roll (HPGR) is gaining acceptance in the mineral processing industry and has become a competitive technology in reducing the specific energy consumption in Mineral processing plants. The amount of samples required for HPGR amenability testwork and HPGR wear tests is usually high and often cannot be available at early stage of projects were only a few drill cores are available. Although HPGR was initiated from small scale piston die compression tests, the development of small scale piston die test to predict the performance of HPGR has been slow. The objectives of this paper was to present the designs, operating procedure of piston-die press and operating conditions which have resulted in similar particle size distribution obtained from a piston die test and HPGR Labwal unit starting from the same feed size distribution. Testwork were conducted using a 2 MN piston-die press and a Labwal HPGR unit on major South African ore types, viz, gold, platinum and iron ores. The results obtained show that piston-die test can generate data to predict energy consumption, product size distribution, and even to evaluate the edge effect.

Jan 1, 2012

By Alessandro Navarra, Roberto Parra, Boyd Davis, Frank Mucciardi

A smelter scheduling algorithm has been developed, which allocates the oxygen production between the smelting furnace and the converter aisle, so as to maximize copper throughput. The algorithm is intended for daily operation planning, controlling the sequencing of the converter cycles, and the oxygen drawn by these cycles. In some cases, it may be worthwhile to decrease converter oxygen allocation in favour of the smelting furnaces. Thus, a better utilization of the oxygen plant can increase primary copper throughput by several percentage points. This principle is demonstrated through sample computations. The approach presented in this paper can be incorporated into smelter management software.

Jan 1, 2015

By R. Holmwood, M. Faris, P. Holloway, M. Collins

Sulphuric acid addition is a major driver of the economics in the processing of nickel laterite ores by high pressure acid leaching (HPAL). Understanding the optimal acid addition rate is essential for the success of any HPAL operation, and this is especially true at Ambatovy, where the composition of the feed tends to vary significantly on a day-to-day basis. Most studies on the effect of acid on nickel extraction in HPAL have used laboratory testwork as their basis. Although these studies are invaluable in assessing the economics of a new project, they are limited by the range of ore composition that can be tested and the differences between the operation of the laboratory equipment and the commercial plant. To enable optimization of the acid addition at Ambatovy, operating data from the HPAL operation were obtained using OSISoft’s PI system and the data from several periods were examined to develop relationships between acid addition and nickel extraction. The initial relationships from 2014 focused on the acid required to achieve a target nickel extraction of 95%, with aluminum and magnesium in ore and feed slurry solids content as the major variables. As Ambatovy ramped up through 2015 and 2016, the calculated acid requirement was further refined to address the effects of HPAL temperature and retention time, and the oxidizing/reducing characteristics of the ore, and to generate acid requirement relationships as a function of ranges of nickel extraction. These relationships supported raising the target nickel extraction to 96% and enabled the development of an economic model between acid addition and nickel extraction.

Jan 1, 2017

By K. Thuro, L. Wilfing, H. Kasling

"In mechanized tunneling, performance prediction is a crucial issue for estimating excavation costs and construction time of a tunnel project. The aim of this work is to compare the calculated parameters by penetration prediction models with the results of penetration tests during excavation by a Tunnel Boring Machine (TBM) at actual tunnel projects. This comparison helps to improve the existing prediction models (Gehring, 1995 and Rostami (Colorado School of Mines), 1997.) and to develop a new, so-called “Alpine Model” (research group ABROCK; Schneider et al., 2012).On-site penetration tests are a common tool to determine performance of a TBM in certain geological environments. During a test, the TBM is operated under defined conditions that allow comparing the results of different projects and machine types. There are two different types of penetration tests in use. The more common type, described by Bruland (1998a), is based on test drives at different thrust levels. The tests in this study are performed as start-stop-tests, meaning that the TBM starts from zero to the maximum possible thrust and reverse with slowly increasing respectively decreasing steps (Frenzel et al., 2012). To gain information about the interaction between TBM and rock mass, a detailed geological documentation including an analysis of the discontinuity pattern and laboratory testing for rock strength characterization are mandatory.Within the last year 16 penetration tests have been performed. The results are thrust- penetration curves (Figure 2) showing that up to a certain penetration rate only crushing occurs (subcritical penetration). From there the desired rock fragmentation process called chipping takes place (Frenzel et al., 2012). These two different fragmentation processes can be described best by a bilinear function as seen in Figure 3. Both, CSM- and Gehring-model, do not fit to the trend of the penetration rates determined during the excavation process as they are using potential or simple linear functions.Another parameter that has to be implemented into the new prediction model is the influence of discontinuities. In case of favorable orientation and spacing, discontinuities reduce the required thrust at same penetration rates. In contrast, unfavorable discontinuity systems can cause blocky faces and hence worse performance than predicted. Besides discontinuities, the toughness of rocks has to be taken into account when predicting the penetration as tough rocks need more energy to obtain complete failure than brittle rocks.Key advantage of these tests in comparison to existing are more data points in less time. By improving respectively extending the existing penetration prediction models with the stated parameters, the penetration prediction for TBMs can be more accurate and also wear calculation can benefit from this approach."

Jan 1, 2015

By D. M. Watson

Mineral discoveries and subsequent extraction have led to the establishment of many small communities, some major towns and a few cities . In Canada, such developments have essentially occurred without benefit of long-range regional or local planning. In the past, this was not a cause for concern. Now, however, rising expectations and reorientation of social values have placed increasing responsibility on government and industry to ensure the long-term viability of communities and regions. Such responsibility means large investments by government in infrastructure and by industry in extractive and processing plants. Uncertainty in the interpretation of ore reserve estimates becomes a critical factor. The traditional methods of reporting reserves - "proven", "probable" , "possible" - may be useful in individual mine production planning, but they are inadequate for planning industrial and public infrastructure, The need for a better information base is critical, with clear and precise definitions of what is being reported, but we are a long way from achieving it. The challenge is therefore to develop a closer professional relationship between government and industry and to tie mineral development to long-range regional strategies.

Jan 1, 1977

By P. J. Oakley, W. M. Thomas, S. W. Kallee, D. G. Staines

A Friction stir welding (FSW) is now extensively used in aluminium industries for joining and material processing applications. The (FSW) technology has gained increasing interest and importance since its invention at TWI almost 15 years ago. The basic principle, recent applications and the continuing development of the FSW technology are described. The paper will introduce some of the variants of FSW, such as Dual-rotation, Twin-stir(TM), and the Stir-lock(TM) technique.

Jan 1, 2006

By P. D. R. Maltby

This paper describes the background and markets for calcium carbonate and silica sand in Canada, as well as the results of recent test work carried out at the Ontario Research Foundation. Tests on sericite, tremolite, vermiculite, barite and graphite are also mentioned.

Jan 1, 1979

By W. J. S. Craigen, G. E. Wittur

"In the context of today's continuously changing world, there are many factors which must be considered when attempting to assess the ability of Canada's primary copper producers to remain competitive in the face of increasing competition in world markets. In this paper, we have attempted to document those factors that will have the greatest impact on the future viability of Canada's copper industry, and to suggest possible strategies to fully utilize whatever inherent advantages Canada may have to enhance its competitive position. Technological factors related to the efficiency of precious and by-product metals recovery, energy type and utilization efficiency, production and sale of sulphur by-products, and control of 502 emissions are given high priority in this evaluation of Canada's future needs to remain competitive. Particular emphasis is placed on assessing the relative viability of hydrometallurgical versus pyrometallurgical processes for copper; to address uniquely Canadian conditions and problems. Due consideration is also given to the economic incentives required to allow Canada's copper producers to compete under anticipated world market conditions and to facilitate the continued development of Canada's copper resources. IntroductionWhen we try to assess the viability or competitiveness of any industry the bottom line is still usually, ""Can we produce a pound of product cheaper than the competition?"" Canada's copper industry is certainly no exception. However, as with most resource-based industries dependent upon exports, there are many factors which have a significant effect on the cost components which make up the total cost of producing and selling a pound of copper. It is desirable therefore to have as clear a picture as possible of the cost components, the major factors affecting them, and how they compare with the competition, particularly the third-world copper producers.In this paper we have attempted to provide a brief outlook for world copper markets and a brief overview of Canada's competitive position. We have also attempted to document those factors which will have the greatest impact on future production costs, and have suggested possible initiatives to utilize inherent Canadian advantages to enhance our competitive position. Special emphasis has been placed on technological initiatives designed to make full use of these ""advantages"", to develop superior beneficiation and extraction! refining technologies. Major factors considered in the present study are:"

Jan 1, 1986

By J. L. Collins

"Une recherche debutee en 1987 tente de cerner divers éléments ayant un impact sur la productivite miniére, de facon à améliorer la planification des operations souterraines. II a été possible de recueillir jusqu'à trente variables dans sept opérations minières differentes du Nord-Ouest québécois. Cette présentation rend compte de quelques résultats préliminaires obtenus à l’une d'entre elle. Entre autres, elle montre comment une association entre une analyse de régression multiple et un logiciel d'optimisation (OPTIMUL) peut servir à une application particulière de la planification d'une opération minière du Québec. Plus spécifiquement, la présentation montre comment une quantité appropriée de ANFO et de TOVEX peut maximiser la quantilé de minerai cassé, minimiser les couts de sautage ou encore minimiser les coûts d'explosifs par tonne de roche cassée, en se basant sur une série de contraintes réalistes provenant de la mine.ABSTRACTA study, underway since 1987, tries to evaluate factors affecting mines' productivity. Information has been collected from seven underground mines in Quebec and this paper shows preliminary results from one. In particular, it shows how a combination of multiple regression analysis, mathematical programming and a set of realistic mine constraints can be used for a particular application of mine planning. More specifically, the paper shows a parallel between maximizing production of tons of broken are, minimizing explosives costs or minimizing the costs of explosives per ton of broken are by an appropriate selection of ANFO and TOVEX quantity of explosives. Finally, the paper shows that minimizing the costs of explosives per ton of broken are is the best alternative to follow providing a special optimization program can be set up."

Jan 1, 1990

By J. Guha, el, G. Bouchard, W. Zuckerk, J. Carignan, G. Archambault

The Gwillim Mine, located 8 km northwest of Chibougamau, is underlain by two mafic volcanic cycles separated by a dominantly felsic cycle. These rocks are part of the Gilman Formation of the Roy Group. The mafic rocks are cut by weak shear zones containing the "North" and "Main" veins, both east-west striking gold-bearing structures dipping 75° to the north. The felsic cycle, which is also gold-bearing, contains textures suggesting a syngenetic origin. The Gwillim Mine presents an excellent opportunity for the study of what may be two coexisting gold deposits, a volcanogenic and a veine type.

Jan 1, 1984

By A. M. King, J. M. Neilsen

"Roughness at varying scales is an important component of the shear strength of discontinuities. Small scale roughness can be assessed in drillcore and through laboratory testing of drillcore derived samples. Large scale roughness, or waviness, also plays an important part in peak shear strength and a number of methods for its incorporation into defect plane strength models are presented.A number of methods for capturing waviness data from exposed faces are reviewed. A method is presented for deriving waviness from downhole televiewer data, which is shown to be significantly more accurate than structural data derived from core logging. The method is based on work undertaken in the highly anisotropic bedded units of the Hamersley Province, Western Australia where televiewer surveys are routinely undertaken. Values of waviness are derived through a review of variation in dip resolved in the direction of the slope face. This method allows design engineers to incorporate large scale roughness in defect plane shear strengths at the design stage.INTRODUCTIONThere are a number of constitutive models currently being applied by rock mechanics practitioners in calculating defect plane shear strength parameters, such as Patton, Barton – Bandis and Hencher [1, 2, 3]. Most of these shear strength determinations are typically undertaken by determining the base or residual friction angle, and applying corrections for small and large scale surface roughness."

Jan 1, 2015

By H. Hitchen

THE PURPOSE of this paper is to indicate the working capacity of different types of ropes for various engineering and mining duties. ROPE CONSTRUCTIONS There are approximately one hundred different designs of ropes in use today but, normally, only about ten are necessary for mining and engineering duties. The rest are designed for unusual equipments, or are different ways of combining wires of special shapes. Basically, the various designs of mining ropes consist of round, triangular, and oval strands, constructed with one or several layers of wire over a single wire, or a compound construction of sever.al wires. To suit different installations ropes are made with 3, 4, 5, or more of these types of strands over a central core, the ?co re itself being manufactured from either a fibrous material or a combination of steel wires. Nevertheless, in mining, the demand for 'locked coil rope', wl1ich may be considered as a single strand, is steadily increasing, especially for use on vertical shaft winding engines. So far as the locked coil rope is concerned, many constructions have been developed to suit different requirements, such as - in addition to winding ropes - aerial carrying Topes, shaft guide ropes and haulage ropes.

Jan 1, 1957

By M. Bryson, S. Broom-Fendley, A. E. Brady, W. Dawes, G. Beer, N. Sehlotho, S. Al-Ali, F. Wall

The Songwe Hill Rare Earth Element (REE) Project in Malawi is a near surface carbonatite-hosted deposit with synchysite and apatite as the key REE bearing minerals. A strong focus has been placed on understanding the REE mineralogy of the Songwe Hill carbonatite as REE mineralogical characterization is a crucial component at all steps, ranging from exploration to production, in the development of REE deposits. Extensive mineralogical work has been completed at Camborne School of Mines (CSM), Natural History Museum (NHM) London, British Geological Survey (BGS), Nottingham, Aberystwyth University, Wales, Mintek, South Africa, and SGS Inc. Canada (SGS). The following analytical techniques were used: scanning electron microscopy (SEM), electron microprobe analysis (EMPA), laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS), and QEMSCAN®. The detailed studies have demonstrated that while synchysite is light-REE enriched as expected, apatite, abundant in all stages of carbonatite emplacement at Songwe, is anomalously enriched in mid- to heavy-REE relative to apatite in other carbonatite deposits. The distribution of REE within synchysite and apatite at Songwe has had important implications for the direction of the metallurgical work with respect to the behaviour of light and heavy REE through the flotation and hydrometallurgical stages of the flow sheet.

Jan 1, 2014

By F. O. Verret

Several grindability tests were developed over the years to design grinding circuits or optimize existing operations. Each test has its own strengths and weaknesses and it is imperative to select the proper test procedure(s) to meet project deliverables and minimize the risk of a project. Pilot plant testing of large bulk samples historically constituted the traditional approach for AG or SAG design, but was gradually replaced by small-scale tests. Nowadays, conducting grindability tests requiring only a few kilos of material on several samples is a more typical approach to grinding mill design. This paper summarises the requirements and deliverables of various bench-scale test procedures, their strengths and weaknesses, and cases where AG/SAG pilot testing should still be performed.

Jan 1, 2012