Search Documents

By J. A. Herbst

Professor Klaus Schönert and his students used fundamental physics to develop many of the principles required for the design and scale-up of "Gutt Bett Zerkleinern" devices such as the high pressure grinding roll (HPGR) or the high pressure roll crusher (HPRC). As the equipment evolved so have the tools used for its selection and analysis. In the current paper discrete element modeling (DEM), Metso's proprietary Fast Breakage simulations, and Schönert's packed bed piston test are combined with energy based population balance models (PBM) to yield an alternative to ore characterization and equipment selection by pilot plant testing. The resulting methodology is used to take the next step in understanding these devices with a view toward predicting plant performance. This paper describes a journey beginning with precise modeling of a small HPGR including stud geometry and system hydraulics. A key to predicting performance is the accurate modeling of individual particles, their motion in the machine, the probability of breakage and redistribution of fragments, and the inter-particle breakage events that occur between the rolls at different pressures, speeds and moisture levels. Advanced DEM simulations and particle breakage characterization methods provide the necessary technology. The resulting combined models were validated using a small diameter laboratory scale unit. The validated physics based model was used then used to predict the performance of plant scale units using a specific energy based scale-up method. Scale-up results are analyzed in terms of power draw, throughput, and discharge product size distribution.

Jan 1, 2012

By K. Soldenhoff, D. Wilkins, E. Ho

In the processing of rare earth ores, a pure, mixed rare earth chloride solution is usually produced and used as the feed to solvent extraction circuits to separate the individual rare earths. Cerium(III) may be separated from the other rare earths by oxidising it to cerium(IV), which precipitates as cerium(IV) hydroxide in chloride liquors. This oxidation step may be inserted either before rare earth separation by solvent extraction or between solvent extraction circuits. Although oxidation of cerium by sodium hypochlorite has been known for many years, detailed conditions for oxidation are not readily available. The effect of hypochlorite addition, temperature, pH and cerium concentration on oxidation of cerium(III) from synthetic solutions was investigated

Jan 1, 2014

By P. Zhang, K. Liu, L. Ou

"The strength and mechanism of Portland cement prepared from stone coal vanadium slag were studied in this paper. Initially, the slag was used as silicon raw materials to prepare clinker. By blending the prepared clinker with gypsum, waste, and fly ash, a series of different grades cement got well prepared. All of performances of the cement were up to the requirements of China’s national standard. The hydration products and microstructure of cement were identified and analyzed by X-ray diffraction and scanning electron microscopy. With the comparison of cement hydration characteristics at different ages, the strength formation mechanism of cement was clarified. The experimental results suggested that adding the fine materials (mainly waste and fly ash) to replace part of clinker would accelerate cement hydration, as it provided additional surfaces for the nucleation and growth of hydration products. And the hydration products were similar to ordinary Portland cement, mainly containing the amorphous calcium silicate hydrates (C-S-H), acicular ettringite (AFt) and portlandite (CH). With hydration time increasing, the hydration products continuously covered the cement particles, resulting in a thicker surface layer. As a result, it gradually condensed into a dense structure block with small pores and smooth surfaces, which led to higher strength. In conclusion, using the vanadium slag to prepare Portland cement can realize the utilization of solid mineral wastes, which will bring huge ecological and economic benefits.INTRODUCTIONWith the development of China’s mining industry, more and more mineral waste residue is discharged every year. These solid wastes cause varieties of resources and environmental problems on people’s living area. While at the same time, the demands of cement are increasing with the remarkable development of the construction industry. Thus, in recent years, utilization of proper solid waste to prepare cement has become an efficient way to deal with the solid mineral wastes problems (Boncukcuoglu, Kocakeri?M, & Tosunoglu, 2002; Simatupang, Hanafi, Purwasasmita, Imran, & Pane, 2012; Tsakiridis, Papadimitriou, Tsivilis, & Koroneos, 2008; Yun, Yong, Choi, Lee, & Lachemi, 2009)."

Jan 1, 2016

By R. L. Bruening, L. Navarro, Izatt. S. R., R. Adiga, R. M. Izatt, N. E. Izatt, A. Sharma, N. R. Patel, B. V. Rao

Bismuth is a notorious contaminant in the electrolytic refining of Cu that can cause cathodes to fail to meet ASTM International standards and not be suitable for use in Cu rod and other downstream products. Bismuth can significantly decrease electrical conductivity, decrease the mechanical strength of the annealed wire, retard recrystallization, and sometimes induce hot shortness during the hot rolling process in the production of rod. As a result, the control of Bi in the refinery tankhouse must be carefully managed. This paper describes how SuperLig® Molecular Recognition Technology (MRT) is being used for Bi removal at the Birla Copper Dahej Copper refinery. The operation of the SuperLig® MRT Bi removal plant is described and data on Bi removal efficiency are presented. INTRODUCTION Hindalco’s Cu division, Birla Copper, operates one of the largest Cu refineries in the world at Dahej, Gujarat; India. The main feed for this refinery is produced at the company’s smelter. Due to its massive production capacity, this operation mainly relies on imported Cu concentrates resulting in a variety of metals being carried out as impurities in the Cu anodes because pyrometallurgical technologies alone are not enough to remove them to the extent required. Metal impurities found in Cu ores include Fe, Zn, As, Pb, Bi, and Sb. During electrorefining, less noble metals dissolve in the electrolyte gradually increasing their concentrations creating the need for electrolyte control mechanisms that remove these impurities with varying degrees of success (Wang, 2004; Navarro et al., 2013.) Bismuth is one of the most significant impurities in a Cu refinery because it has the lowest ASTM product specification. This situation is critical because the Bi potential is very close to that of Cu making it possible to plate in the Cu cathode directly. Also, Bi can precipitate at high concentrations causing floating slimes and reduction of current efficiency (Ballinas, San Miguel, Munoz, & Gyves, 2003). Production of high purity cathodes from feed stock containing a diverse range of metal impurities becomes a major challenge in the refining of Cu (Izatt et al., 2015). In this work, the purification strategy followed by Birla Copper for the removal of Bi using a separation process based on MRT is presented, outlining the loading and stripping performance of SuperLig®83 and the benefits of using MRT over other lower selectivity methods where hazardous materials are produced instead of high purity products.

Jan 1, 2019

By John C. Robbins

A new technique for the determination of trace levels of uranium in solution has been developed. A compact laser emits short, but intense, ultraviolet pulses to excite the green fluorescence of a uranyl-complex formed by the addition of a proprietary reagent to the sample. Organic species present in most natural waters also fluoresce quite intensely, but their emission does not last appreciably longer than the excitation pulse, in contrast to the relatively long persistence of the uranyl fluorescence . Electronic 'gating' is employed to separate the long-lived contribution, rejecting substantially the organic emission. Results using the laser fluorescence method on many sets of natural waters of various origins have been compared against corresponding values generated by independent laboratories. Correlation has been generally good over a range from less than 0.1 to more than 100 ppb U. Solid samples have also been analyzed after extraction of the uranium into solution. Accuracies adequate for most exploration purposes have been achieved, but further work is required to determine effects of interferences in samples with complex matrices. The transport and deposition of uranium in natural waters is controlled by the organic and inorganic chemistry of the waters involved. It is suggested that interpretation of very low uranium levels will be aided by additional measurements of conductivity and organic content, with subsequent statistical treatment.

Jan 1, 1978

By S. Kelebek, B. Ingram, C. Gibson, T. MacNeil, M. Aghamirian

"The beneficiation and upgrading of pyrochlore from its ores is carried out through flotation. In industrial practice, upgrading is conducted in a two-stage flotation process in which pyrochlore flotation is carried out after gangue mineral pre-flotation (carbonate, silicate, sulphide or phosphate reverse flotation). In this study, the flotation of pyrochlore from a low grade carbonatite ore was performed at the laboratory scale following a two-stage flotation process in which carbonate minerals were floated in advance of niobium minerals. In parallel, a simplified flotation process was developed in which pyrochlore was floated directly from gangue minerals at increasingly acidic pH. Laboratory results indicated that both two-stage and direct flotation provided similar results in terms of niobium grade-recovery. Based on these results, a large scale, integrated pilot plant was conducted using a direct flotation flowsheet. While the elimination of reverse gangue flotation resulted in flowsheet simplification, the dissolution of carbonate minerals and the subsequent effect of dissolved cations on the floatability of pyrochlore added an element of complexity. A comparison of results from locked-cycle laboratory testing and pilot plant testing highlights the challenges of scaling up a complex flowsheet. A case is made for the direct flotation process and the key parameters to achieving success in large scale direct flotation of pyrochlore are discussed.INTRODUCTIONPyrochlore (Ca,Na)2Nb2O6(OH,F) is a niobium bearing mineral which has been the primary global source of niobium since the first pyrochlore mine commenced operations in the late 1960s (Gibson et al., 2015a). Preceding the discovery and development of high grade pyrochlore deposits in North and South America, the majority of global niobium supply came from gravity concentration operations of columbite (Fe,Mn)Nb2O6, across Africa (Perrault and Manker, 1981)."

Jan 1, 2016

By Min-Sung Kang

Excavation and earthmoving equipment mostly operate in accident-prone areas. These areas normally have rollover, confinement, and fall or may be considered harmful work areas due to demolitions and sewage removals. It is inevitable that excavation and earthmoving systems should be developed to secure the safety of operators through unmanned and remote control systems. Therefore, this research proposes a system that enables excavators to be unmanned and remote controlled without any renovation, remodeling, change, or transformation by applying attachable and separable mechanism and modules. Moreover, this research proposes the sensor module to evaluate the dynamic status without processing remodeling or transformation the existing hydraulic drive excavation system by adopting the easy attachable and separable mechanism. The study verifies this proposal based on observed possibility and feasibility through the experiments.

Aug 1, 2013

By W. A. Lang

COAL of sub-bituminous rank underlies much of the plains area of Alberta. This coal is geo-logically young, and occurs in Belly River and Edmonton strata of Up-per Cretaceous age. Generally, the seams are flat-lying, but in some areas they may dip as much as 5 degrees. The overburden, composed mainly of glacial clays and sand-stones, may vary in depth from a few feet to several thousand feet. Recovery of the coal has 'been by drift, slope, and shaft underground mines, and by open-pit stripping operations. Production has been obtained from a large number of mines, most of which have been relatively small and with preparation equipment limited to a loading tipple with screening facilities, and a picking belt where high-ash materials can be removed from the larger sizes. The coal has been sold for domestic and industrial space-heating, for production of process steam, and for power generation. In re-cent years competition from natural gas, propane, and oil has seriously interfered with the production and marketing of sub-bituminous coal, especially with the disposal of the smaller sizes at a realistic price.

Jan 1, 1958

By J. Dennett, M. Faris, M. Antonio, M. Collins, N. Tuffrey, R. Ellenwood, V. Reddy

"In January 2012, AngloGold Ashanti Córrego do Sítio Mineração, with assistance from Sherritt International Corporation, commissioned a new autoclave for pressure oxidation of refractory gold concentrate at the Córrego do Sítio operation in Brazil. Start-up of the plant occurred in a few weeks and enhanced gold recovery was realized almost immediately, with 94% gold extraction achieved in carbon in leach (CIL), compared to less than 70% without pressure oxidation. This paper describes start-up and commissioning of the plant and provides an overview of plant performance over the last five years.INTRODUCTION In 2008, AngloGold Ashanti purchased the former São Bento property from Eldorado Gold, which, along with AngloGold Ashanti’s existing Córrego do Sítio mine, was renamed AngloGold Ashanti Córrego do Sítio Mineração (AGA Mineração). Later that year, the Sherritt Technologies division of Sherritt International Corporation (Sherritt) was contacted to begin batch and continuous pilot plant tests to determine the amenability of the AGA Mineração refractory gold concentrates to the pressure oxidation process. Based on the results of the batch and pilot plant tests, AGA Mineração requested basic and detailed engineering studies to be conducted by Sherritt, eventually leading to commissioning of the plant in January 2012. AGA Mineração’s plant is located in southeastern Brazil in the state of Minas Gerais, near the city of Belo Horizonte. AGA Mineração`s Phase 1 mine plan covers three sites in the Laranjeiras, Carvoaria Velha and Cachorro Bravo ore bodies, and is designed to process 60,000 tonnes of refractory gold concentrate per year to produce 140,000 ounces of gold per year with an 11 year life of mine (AngloGold Annual Financial Statements, 2010). Recovery of gold at AGA Mineração is based on Sherritt`s pressure oxidation technology for refractory gold concentrates (Berezowsky et al., 1991; Collins et al., 2011a; Collins et al., 2011b). This process had previously been applied to the recovery of gold at the São Bento site (Carvalho et al., 1988; de Silva et al., 1989), in a plant that was operational between 1986 and 2007 (Silva et al., 2004)."

Jan 1, 2017

By N. Parnian

"Carryover of caustic soda (NaOH) in the steam path caused catastrophic failure of superheater 304H stainless steel tubes in a steam generator and led to an unexpected shutdown after just five months of continuous service of petrochemical following the start of production. The cause of the failure was studied, with a focus on the formation of sigma phase in the weld joint and effect of caustic embrittlement on stress corrosion cracking (SCC). The cracks were examined at the seam weld, heat affected zone (HAZ), and Ubend areas. Hardness was measured for the base metal, HAZ, and weld metal, and microstructures were examined using optical microscopy and scanning electron microscopy (SEM). Crack initiation is attributed to gouging on the precipitated carbide at the HAZ and also the formation of sigma phase in the weld metal, as shown by energy dispersive X-ray (EDX) analysis. In addition, cracking was propagated by caustic embrittlement because of residual stresses and hammering. Finally, the characteristic feature of fracture was illustrated by SEM fractography, and consists mostly of intergranular SCC and some quasicleavage transgranular. INTRODUCTIONThree key factors are needed for the initiation and propagation of intergranular stress corrosion cracking (IGSCC): a susceptible material, a corrosive environment, and sufficient stress. Although austenitic stainless steels are susceptible to sensitization and IGSCC, they are widely used in boiler and superheater tubes because of their high corrosion resistance, high oxidation resistance, acceptable mechanical characteristics at elevated temperatures, and low cost.Sodium hydroxide is injected to neutralize acidic constituents in the steam path, but caustic can concentrate in boiler tubes and attack the surface metal (known as gouging) even traces of caustic in the steam can deposit on surfaces and cause local concentrations of several percent (ASM handbook, 1992). Not only sensitized grains but also sigma phase formed in the weld metal can initiate caustic cracking. In this research, the cause of the failure of 304H stainless steel superheater tubes in a methanol petrochemical plant in Iran was studied with a focus on the effects of caustic embrittlement on IGSCC."

Jan 1, 2012

By A. Saigal

The effect of temperature on the cutting forces during machining of alumina reinforced aluminum composites was investigated, Aluminum 6061, 10% Al2O3 reinforced composite and 20% Al2O3 reinforced composite were tested, A 5/8-inch diameter high-speed steel end mill, a Micro 100 TiN coated single edge endmill cutter and a two-fluted solid carbide insert cutter were used for tooling, The results, in general, showed an increase in the cutting forces as the temperature of the material increased, From the raw data, there are temperatures ranges in which the force data did decrease but they were insignificant with regards to predicting a downward trend. A regression analysis was used to understand which variables had the greatest affect on the forces being generated, The correlation and regression analysis showed that at 600 rpm (velocity: HSS- 98,2 sfpm, Micro 100 cutter - 78,5 sfpm, solid carbide cutter - 192,4 sfpm) the tooling, the workpiece material, built up edge, and temperature were statistically significant factors in the test, Tooling was a significant variable in all testing, The smallest forces recorded during machining were generated with the solid carbide two-fluted endmill cutter, Visually, the solid carbide tooling produced a better surface finish during the testing which made it the tool of choice, In addition, the force data proved that as the cutting speeds were increased, the cutting forces decreased.

Jan 1, 2005

By Jerry Ran

Many large underground mines using the open stoping method have changed their primary applications of consolidated rock fill (CRF) to paste or consolidated hydraulic fill due to considerations of demand in infrastructure and equipment, system reliability, backfill capacity and material sources. However, some smaller or even large mines still use or consider using CRF for backfill purpose due to factors such as capital expenditure, availability or suitability of other fill types or in some cases local regulatory requirements. As demands on CRF applications diminish among major mining companies, there is a lack of recent literature on application of CRF to open stoping in design and operation. There are several methods being used for fill strength design. Results from these methods have been successfully applied to paste or hydraulic fill. However, the design strength for CRF is much higher than that determined by use of these widely accepted methods. In operation, CRF preparation and placement have significant impacts on the quality of placed CRF and therefore the mining performance. This paper reviews the current fill design methods and their applications to open stoping with presentation of the bench marking data, presents fill failure cases and various CRF preparation and placement arrangements and discusses quality assurance and control programs.

Jun 1, 2012

By J. P. Weiler

The increasing use of high-pressure die-cast magnesium alloys in the automobile industry requires a better understanding of the mechanical properties, the microstructure, and particularly, the relationship between these two. The goal of this study is to first understand the microstructural features which control the mechanical properties observed from an AM6OB magnesium alloy, and second, to be able to predict the local mechanical properties based on microstructural features encountered in different areas of the die-cast component. The two main tools used in this study are spherical indentation testing, used on local areas of the die-cast magnesium alloy AM6OB to detect changes in microstructure and mechanical properties, and X-ray tomography, used to non-destructively investigate the internal porosity in a sample. The results from these tests are then used to predict the local mechanical properties such as the yield stress, the strain-hardening characteristics, and the fracture properties of the AM6OB component.

Jan 1, 2006

By Wm. T. Bray

SYNOPSIS Canadian Refractories, Limited, produce a wide range of basic refractories. The chief raw material use in their manufacture is the magnesite which is mined, and beneficiated in a heavy media separation plant, at Kilmar, Que. This paper describes the underground operation and the plant and explains how the gravity separation of light, siliceous gangue from the ore has changed the mining practice, increased the ore reserves, and improved the chemical uniformity of the crushed ore. HISTORY REFRACTORIES are essential in the production of steel and base metals and in other high-temperature processes. Basic refractories, chiefly composed of magnesia which is obtained by burning magnesite, are used to line and repair basic furnaces. When World War I cut? off the importation of Austrian magnesite, upon which North American industry had depended, domestic sources bad to be found. In Quebec, work was begun on deposits of magnesite at Kilmar, half way between Ottawa and Montreal and about ten miles north of the Ottawa river. By the end of the war substantial tonnages were being quarried and calcined, but, when Austrian magnesite again became available, the industry declined rapidly. In 1925, the National Research Council, in co-operation with the Federal Department of Mines, began an investigation of the industry's technical problems. The result of this research work, which was taken over fully by the Company in 1943 and is actively continued, is that the single product of the early 1920's has been supplemented by more than forty specialized products serving the metallurgical and chemical industries across Canada and in more than thirty other countries.

Jan 1, 1951

By J. C. Murray

Introductory: In dealing with a topic so large, one that involves such a multiplicity of details, and that also has certain controversial aspects, it is quite impracticable within the limits of this article to touch upon many most interesting phases and incidents. Also, to bring out the actual truth, it is necessary to make certain categorical statements. The writer believes that all such statements made here-under are supported by facts. Again, however, it is out of the question to cite all the proof. The writer, therefore, will gladly answer any pertinent criticisms or questions and thus supplement the unavoidable brevity of this paper. Controversial points will take care of themselves. Historical: For present purposes the history of gold mining in Nova Scotia may best be summed up in a very few paragraphs, in some of which the writer quotes freely from recent reports compiled by himself. The first material discovery of gold was made in the year 1860. As this and rapidly succeeding discoveries were looked upon as bonanzas, the claims were fixed at a size of 20 by 50 feet, and a yearly rental of $20 was charged. Later the claims (areas) were increased in size to 50 by 150 feet. In the year 1866 a temporarily successful company, so we are informed by a contemporary writer, owned a mill and mining plant worth $6,000. As this fact is cited with admiration, it is apparent that most of the mining and milling must have been done in a very primitive manner indeed.

Jan 1, 1926

By D. W. McDonald, N. A. Duke, R. L. Hauser

"The NERCO Con Mine is situated in the amphibolite facies aureole of the Western Plutonic Complex overprinting the Yellowknife Greenstone Belt. Metamorphic grade of the upright monoclinal basaltic succession decreases from hornblende-amphibolite facies along the border of the batholith to greenschist facies. Metamorphic isograds, subparalleling the faulted margin of the batholith, transect volcanic stratigraphy and coincide with major goldbearing shears.Gold mineralization is confined to north-striking, west-dipping shear zones where hangingwall amphibolite facies mineral assemblages retrogress to chlorite-carbonate-sericite-sulfide bearing schists hosting multiple generations of quartz-ankerite veins. The gold-producing portions of the Con and Campbell Shears occur where these structures transect an east trending thermal corridor. The corridor is defined by granitic plugs and a number of related breccia bodies, that can be traced outwards from the batholith across the greenstone belt.Prograde reactions of greenstone during amphibolitization effectively liberate fluids that partition metals. With retrograde reactions at shear zones, gold is precipitated with quartz due to the destabilization of sulfide and arsenic complexes. The coupling of regional prograde metamorphic and restricted retrograde metasomatic overprints suggest mineralization is temporally related to emplacement of the Western Plutonic Complex. Economic gold concentrations within the intrusive corridor indicates enhanced metamorphic overprint of hornfelsed greenstones enveloping satellite intrusives peripheral to the main batholith."

Jan 1, 1993

By F. Rivard, M. G. Drouet, W. S. Ruff, P. Carabin

"In both the hot rotary-salt-furnace (RSF) treatment of aluminum dross and the cold ball-millsieving (BMS) treatment of zinc dross, enormous amounts of energy and recoverable metal are wasted and large amounts of greenhouse gas are produced. Such wastes and the environment pollution could be avoided by using the DROSRITE PLUS™ technology. Economic and GHG production comparisons between the presently used industrial treatment processes and DROSRITE PLUS™, supported by over one hundred tests conducted in Canada, the US and Europe, are presented. The savings, with DROSRITE PLUS™, would be about $191 and $418 per MT of aluminum and zinc dross, respectively.INTRODUCTIONDross is a material, which forms on the surface of molten non-ferrous metal, such as aluminum or zinc, during melting, metal holding and handling operations when the molten metal is in contact with a reactive atmosphere. Dross normally consists of metal oxides entraining a considerable quantity of molten free (unreacted) metal, and for economic reasons it is desirable to extract the free metal before discarding the residue. In the case of aluminum dross, recovery of the metal is usually carried out by treating the dross in a furnace at a high temperature (Peterson et al., 2002). By contrast, cold zinc dross is crushed in a ball mill followed by sieving to separate the coarse metal portion from the fine oxide residue.The conventional aluminum dross treatment process, using gas or oil-heated rotary salt furnaces (RSF), is thermally inefficient and environmentally unacceptable because of the salt slag and CO2 produced from the combustion of fossil fuels. In the past several years, a number of salt-free processes have been developed and some of these have found limited commercial use (Gripenberg et al., 1994; Lavoie et al., 1990). In all these dross treatment processes, heating of the cold dross in a rotary furnace requires an external energy input that varies between 375 and 2,500 kWh per (metric) tonne of dross. Molten metal separated during processing of the heated dross is tapped, and the remaining solid residue is discharged from the furnace."

Jan 1, 2012

By S. Ng, Peter Stapleton, Paul Mankowski, J. Spence, R. Siy

"Syncrude has developed a low energy extraction process for the recovery of bitumen from oil sand. This new process operates at a temperature of 25 °C, resulting in substantially lower energy costs and lower capital costs, especially for the thermal energy generation equipment. The process will be used in Syncrude’s Aurora Mine, which is scheduled for startup in mid 2000. The flowsheet for Low Energy Extraction includes hydraulic transport of oil sand slurry, and bitumen separation using collector and frother chemicals and air as process aids. A number of flow sheet innovations and optimizations have been included, resulting in the next generation of extraction technology. Experimental pilot plant results, engineering progress to date and areas of ongoing work will be discussed. SUMMARYThe Low Energy Extraction Process has been successfully developed for commercial implementation at Aurora. The 1996 100 tonne hour Field Pilot demonstrated that the bitumen recovery target could be met with an 11.1% grade oil sand. However, pilot plant bitumen recoveries for a lower grade oil sand were not acceptable. The subsequent flowsheet optimization study led to a new flowsheet for Low Energy Extraction, which includes a primary separation vessel, a flotation circuit for PSV middlings, and the use of middlings displacement in the PSV cone bottom with flotation underflow. A test program conducted in 1997 showed that the new flowsheet could significantly improve the bitumen recoveries for lower grade oil sands. Engineering work on process scale-up led to selection of a 30 meter diameter PSV, with a tangential feedwell. The successful development and commercialization of Low Energy Extraction for the Aurora Mine Project is a major enabling step in the Syncrude 21 program. The low energy requirements of this process allow Syncrude to develop the Aurora leases more cost effectively. The use of this process results in major capital cost savings, predominantly in the thermal energy infrastructure and also provides long term operating cost advantages for Syncrude."

Jan 1, 1999

By L O. Montpetit

The economics of the asbestos mining industry of Canada, and the physical and chemical characteristics of asbestos fibre, as well as exploration, mining, milling and quality control methods, have been described by several authors in the past few years. The scope of this presentation is to survey the application of asbestos fibres in the major product groups of the construction industry in North America. Principal categories considered include flooring materials, asbestos-cement pipes and building products, high-temperature insulation, textiles, saturated asbestos felts and asphalt com pounds. During 1962, the asbestos mining industry of Canada produced an estimated 1.3 million tons of chrysotile fibre grades, and production capacity is expanding. The market demand for chrysotile fibre, on this continent, has been in the order of 50 per cent of the production volume. The asbestos industry is dependent for growth on the construction industry. Product research is active in finding new uses for asbestos fibre; some of the new developments are presented, including the use of short-fibre asbestos grades for extending the life of asphalt pavement.

Jan 1, 1963

By Y. Zedan

Cutting fluids play important roles during machining, including the reduction of friction and temperature. Using a cutting fluid, however, degrades the quality of the environment and increases machining costs. The aim of the present research work is to study the effect of cutting fluids and their interactions with cutting parameters on the quality of holes during the drilling of 6061-T6 aluminum alloys. The lubrication types and modes investigated are dry machining, flood lubricant machining and minimum quantity lubrication machining (MQL), while the part quality criteria include the surface finish, the dimensional accuracy, and burr forms and sizes. A scanning electron microscope (SEM) was used to investigate the formation of built-up edges (BUE) in the drill flutes as well as the surface texture of drilled holes. It was found that dry machining and MQL machining can produce parts having quality levels comparable to those obtained in wet machining, when using the optimal cutting conditions.

Jan 1, 2011