Search Documents

By L. Paulino, C. E. Zangiacomi, J. Yamamoto

"This paper presents the learning from Alcoa Po9os de Caldas Smelter in Brazil, after several energy restrictions resulting from the failures of three rectifier units at its power switchyard. Starting on December 27th, fuses and diodes failed in three rectifier units of Potline #1, causing a long and dangerous power interruption. Even after current was reestablished, amperage was only 70% of the line target leading to a bath freezing process that lasted for around 48 hours. The process engineering team played with several potroom parameters as pot resistance, bath and metal levels, alumina feeding and bath chemistry in an attempt to minimize impact on the potline metal output and energy consumption. As it will be illustrated, the first battle was to keep the pots running on a ""survival"" approach. After that, several changes took place on the procedures used to run at reduced current which were considered rather successful. Finally, some recommendations will be given to foresee and prevent transformers and rectifiers from undesirable failures."

Jan 1, 2006

By Karen M. Moffitt

Developments in mining methods and rates have led to an increase in the frequency and size of waste dump failures that have not been adequately predicted or explained in terms of conventional slope stability analysis. Monitoring data and visual observations suggest a unique mode of failure responsible for large runout events. A numerical model has been developed to capture commonly observed patterns of deformation, and investigate the formation of the ensuing failure mechanism. The analyses have yielded a good correlation with observed field behaviour and have provided significant insight into the coincident stresses and deformations within the dump. Results indicate that while creep effects in the waste dump could have a significant effect on the magnitudes of displacement, the overall dump stability is governed by the strength of the foundation soils underlying the toe region. Consideration of both the stress and velocity fields leads to factors of safety for various dump heights and foundation slopes that are considerably less than predicted from limit equilibrium analysis. The results suggest that conventional limit equilibrium analysis techniques may not be adequate when assessing the stability and design of waste dumps on steeply sloping terrain.

May 1, 2001

By J. Gogal

Cameco's Cigar Lake Operation (CLO) started commercial uranium ore production in 2015. Initial mining was focused in areas of the ore body with relatively low concentrations of elements of concern (EOCs). As mining progressed into areas of the ore body that were richer in EOCs, some statistically significant behavior of certain analytes was noted in the water treatment circuits. It was ultimately found that the CLO ore body natively hosts numerous alkyl arsine compounds in addition to inorganic arsenide minerals. The alkyl arsines were found to be recalcitrant to typical adsorption on ferrihydrite, with the degree of recalcitrance associated with the degree of alkylation. A number of changes to the process circuits and water balance were performed and planned in order to inhibit the transport of alkyl arsines from the ore stream into the process water stream, and to optimize the overall site water usage. In some instances, the interactions of equipment in conjoined circuits of the process had controlling effects on the behavior of the overall circuit. Work continues to iterate upon the capital design features in order to further tighten the water balance, and to optimize water usage and operating costs.

Jan 1, 2020

By Harry V. Warren

Introduction Any person concerned with the welfare of mining in British Columbia cannot help being perturbed by the fact that the industry, to an alarming extent, is living on its capital. The great majority of mines and mining camps of today represent a heritage handed down by the prospectors of yesterday. It is true that mining engineers, geologists, mineral dressers, metallurgists, and their fellow scientists and engineers have played an honourable, indeed a vital, part in he1ping to make our producing mines, often after costly and extensive underground development and extended researches. It is also true that the mineralization at the Sullivan, Britannia, and Copper Mountain mines was all discovered before the turn of the century. Likewise the Cariboo, Bridge River, Hedley, Ymir, Rossland, Boundary, Slocan, Salmo, and Portland Canal mining areas, although they had not all been developed, were all known more than fifty years ago. Furthermore, every one of these camps owed its discovery and eventual exploitation to the fact that encouraging ' mineralization occurred at the surface. Where would the mining industry of British Columbia be today had those precious outcrops been buried beneath twenty to forty feet of glacial drift or other overburden? Anybody familiar with the geology and geography of British Columbia will probably agree that finding new mining camps is going to be an increasingly difficult and costly business: disappointments there will be in abundance. Nevertheless, most persons will probably also agree that other valuable mines and even mining camps await discovery by those who will prove resourceful and lucky enough to unearth them. It has become increasingly obvious to the authors of this paper that any new too1s which can aid either prospectors or engineers in their search for new orebodies should be welcome. This paper outlines our efforts to develop biogeochemistry and related techniques to the point where they may be considered as useful tools in the search for hidden mineralization.

Jan 1, 1950

By CIM Mineral Resource

On January 9, 2018, the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Council formed the CIM Mineral Resources and Mineral Reserves Committee (CIM MRMR Committee), which is a combination of the previous Standing Committee on Reserve Definitions and the Best Practices Committee. As part of its mandate, the CIM MRMR Committee updates guidelines for use by Industry, which include the Uranium Practice Guidelines. The 2024 CIM Uranium Leading Practice Guidelines were adopted by CIM Council on November 22, 2024, and supersedes the 2003 version. The main principles and guidelines relating to preparation of Mineral Resource and Mineral Reserve (MRMR) estimates are provided in the CIM Estimation of Mineral Resources and Mineral Reserves Best Practices Guidelines (MRMR BP Guidelines, as updated from time to time). The MRMR BP Guidelines provide information pertaining to metalliferous and other deposits and many sections are readily applicable to the preparation of MRMR estimates for uranium deposits. However, additional guidance is appropriate for uranium deposits due to the radioactive nature of uranium, and its amenability, in some cases, to in situ recovery (ISR) mining methods.

Nov 1, 2024

By C. Dragusanu, J. Sims, J. Connolly

Based on a statistical analysis of the categorical and numerical data from the established geological model, a geochemical classification of mineralization has been shown to be objective in nature and correlated to the envisioned metal extraction process. Multivariate chemical classification has the potential to discriminate within a combined response from different types of alteration and metal abundances. Distinct domains of chemical response determined by clustering analysis were used as a validating criterion for a geologically driven metallurgical testing program. The groups established are spatially linked to the geological process responsible for their genesis, providing clarity in geometallurgical and resource modeling.

Jan 1, 2011

By N. Morrison, I. Holl, R. Welyhorsky, A. Hempstock

ABSTRACT: The Victor diamond mine is located in the James Bay lowlands, 90 km west of the First Nations village of Attawapiskat. The project was the first of its kind in northern Ontario. The process plant was designed to produce a 95 to 98% by weight diamond concentrate through three stages of comminution, dense medium separation, and proprietary X-ray technology for final recovery. The plant was commissioned over a period of six months, commencing prior to substantial completion of construction. Through effective planning of the commissioning phase, the Victor mine start-up was safely completed nine months ahead of schedule.

Jan 1, 2011

By George P. Demopoulos

In a departure from the traditional domain of hydrometallurgical extraction processes we consider new R&D opportunities for innovative application of solution processing into the advanced green energy and clean technology fields. It would not be an exaggeration if we state that protection of the environment via advancement of clean technologies on the one hand, and harvesting and utilizing renewable energy in a sustainable and cost-effective way on the other hand are clearly among the top pressing global priorities. When hydrometallurgy is approached on the basis of its aqueous chemistry and reactive processing fundamentals, it can indeed provide a highly fertile ground for innovation outside the "box". In this context therefore we will present highlights from our recent research that is directed towards the development of new generation HCl recycling, environmental, and solar energy conversion/storage technologies. In all systems the research is approached via the innovative integration of aqueous process engineering and material chemistry principles. The presentation will include discussion of (i) the development of crystallization-based HCl regeneration technologies; (ii) the supersaturation-controlled production and encapsulation of scorodite that was recently commercialized; (iii) the aqueous synthesis of nano-TiO2 and its electrophoretic deposition into solar cell electrodes; and (iv) the hydrothermal synthesis of nanostructured lithium titanate and lithium iron phosphate materials to make lithium-ion batteries destined for electric cars.

Jan 1, 2014

By T. R. Chari

The safe-level dilution of low-level radioactive wastes in large volumes of selected granular material is proposed as an alternative method of permanent waste disposal to current Canadian practice of concentration and encapsulation. Accepting the fact that a "background level" of radioactivity exists throughout the world, the authors feel that the concept of controlled dilution of radioactive wastes to a level in keeping with "background" is a plausible alternative to current thinking on the subject and is worthy of equal consideration.

Jan 1, 1979

By Marcel Vallee, D. C. Gagnon, C. CARBONNEAU, P. ST-JULIEN

The Magdalen Islands archipelago, a cluster of fifteen islands, is located near the centre of the Gulf of St. Lawrence on the thickest portion of the Carboniferous Fundy Basin of the Maritime Pro vinces. The bedrock of the Magdalen Platform includes a thick succession of evaporites of Visean Age, occurring as a series of thickenings, ridges, domes and diapirs reaching a probable vertical thickness of close to 6000 m. The emplacement of 1hese salt structures by flowage has much dislurbed 1he SlrOligraphic sequence of the rocks of the Windsor Group, particularly 1he Havre-aux-Maisons Formation. Subsequent tectonic movemenl has broken the overlying Cap-auxMeules Forma1ion info an assemblage of panels and blocks now slightly tilted. Following detailed gravimetric surveys and more than 30,000 m of diamond drilling, SOQUEM has discovered, at various dep1hs, seven salt domes on four of 1he main islands of the archipelago. These evaporite bodies generally are localized near the cemre of complex anticlinal struclUres where diapiric movements and faulting have disturbed the original stratigraphic succession. At Rocher du Dauphin near Grosse 1/e, in 1he northern part of the archipelago, Seleine a SOQUEM subsidiary is developing a mining complex with an annual capaci1y of 1,250,000 1onnes of deicing salt for 1he Canadian and Eas1ern United Swtes marke1s. The stan of operations is scheduled for April 1982.

Jan 1, 1984

By J. A. Russell

"UNTIL the last few years, the collieries of the Dominion Coal Company, Limited, while highly mechanized as to the cutting and transportation of the coal, still relied on the hand-loading of coal from the seam onto face conveyors. In these circumstances it was possible to assure that no large proportion of extraneous materials would be loaded with the coal, and the product could be quite well cleaned for the market by screening and hand-picking.Within the past few years, however, the Company has introduced an intensive programme of mechanization which will result in the virtual elimination of hand-loading .of coal. It has been the experience of other producers that mechanical loading inevitably leads to a very large increase in the amount of impurities in the product. This is occasioned by the fact that, at least up to the present, all types of loading machines have relied on the coal being broken from the seam by under-cutting and shooting. In this operation, a certain amount of roof and pavement material inevitably becomes mixed with the coal and, since selective loading is impossible with a loading machine, all this foreign material is loaded out with the product."

Jan 1, 1952

Deformation is a critical indicator required to evaluate the structural safety, stability, and integrity. For example, the deformed shape of a building structure is a key parameter that needs to be measured and tracked during laboratory testing or post-disaster inspections. However, existing techniques used for the deformation measurement and tracking do not have all the desirable characteristics, such as: reliability, accuracy, low-cost and simplicity of tools installation. In order to address this issue, a novel method has been proposed in this study. The method consists on using the image processing technique to automatically measure and track the deformations of concentrically braced frame (CBF) structures. Accordingly, the critical points in a CBF structure are first identified and the topological configuration of the structure is retrieved. The points and topological configuration characterize the basic shape of the structure. In this way, the deformation of the structure can be determined by measuring and tracking these points and their topological configuration. To show its effectiveness, the proposed method has been tested against the manual deformation measurements.

Aug 1, 2013

By G. V. Sirianni, G. E. Viens, R. A. Campbell, G. N. Banks

A combination shaft-electric furnace for the smelting of ores and the melting of metallized feed is being developed at the Mines Branch. When iron oxide pellets are smelted in this unit, they are preheated and partially reduced in the shaft before being transferred to the electric furnace where smelting is completed. Also, limestone flux added with the pellets is-preheated and calcined in the shaft. It has been demonstrated that, in smelting iron oxide in this unit, the throughput of the 250-kva electric furnace can be approximately doubled and the amount of electrical energy required can be very significantly reduced when the shaft furnace is operated in conjunction with the electric furnace. These benefits are achieved mainly by utilizing the sensible heat and latent energy contained in the arc furnace off-gases.

Jan 1, 1971

By Zhenyu Han, Dion Weatherley, Ruslan Puscasu

"This study aims to demonstrate the capacity of the Discrete Element Method (DEM) to model and simulate fracture in brittle rock, capture the crack propagation process and determine crack propagation rates for various levels of external loading. In the numerical experiments reported here, a macroscopically homogeneous body of brittle rock, containing a single pre-existing crack, was subjected to tensile stress loading. Simulations concerned with model I crack growth process in 3D were carried out. The process of fracture has been observed under various steady state and dynamic conditions. The numerical results obtained reproduce qualitatively and quantitatively a variety of observed fracture phenomena. Specifically, this study examined the onset of cracks, single dominant cracks that grow across the specimen, crack bifurcations and branching. The density of fractures that can be nucleated and grow to a significant size with and without arresting each other, crack growth speed and stress distribution, all have been consistently and systematically analyzed. Suggestions on potential future developments are made and discussed.INTRODUCTIONFracture and failure mechanics are very important in mining, manufacturing, materials processing, mineral processing, civil and mechanical engineering, and many other disciplines of science and engineering. Yet, due to the complexity of fracture phenomena, no theoretical models of broad applicability are currently available (Bieniawski 1967). The simulation of crack propagation is therefore considered an open question in numerical rock mechanics. Although, a significant body of experimental research on fracture of materials was carried out since the early days of fracture mechanics (circa 1940s) (Poncelet 1946, Mott 1948), often in parallel with the development of fracture mechanics theories as well as with the development of experimental and observational techniques themselves, the experimental results were often done on particular classes of material such as glasses and other very brittle materials. Indeed, a number of specific experimental observations on the behavior of growing cracks in brittle materials were made in the 1940s for which generally accepted explanations based on physical principles are still lacking. Likewise, quantitative numerical modeling, based on both continuum and discrete methods, as a basis for understanding dynamic crack growth is still in a preliminary stage."

Jan 1, 2015

By Ali Montaser

This paper presents an experimental study conducted to facilitate the use of RFID on construction job sites. The study focuses on deployment settings to provide data acquisition with higher accuracy for indoor location sensing. It provides extension to the state-of-the-art in this field as it addresses the impact of metal media proximity to RFID tags, the reasonable duration for data capturing, number of RFID tags employed and the distance between them. Low cost passive RFID tags were used in the experiments where each tag is used as a reference point with a known location. Five hundred and forty (514) experiments were conducted in lab environment using a 3m by 3m test bed that is dynamically rearranged to generate 15 test beds and a total of 67713 data sets were collected and analyzed. The collected data were captured from nine locations for each test bed at four time intervals. Received Signal Strength Indicator (RSSI) was used as the main attribute for signal measurement to process the captured data. Results of the data analysis performed are studied under four main categories: duration, number of tags, locations of tags and metal interference. The best duration was found to be the 15 second in the test bed with the least number of tags; as the short amount of time to capture data did not allow creation of a lot of interference among the emitted signals. Within each test bed, errors occurred most at points where the received signals were not well distributed in a 360 degree vicinity of the data capturing point. It means that the center point of each test bed resulted in lowest errors and the points located on the extremities led to the highest errors. Finally, metal objects were found to have major impact on the accuracy of the captured data; to the level where reliable values for errors could not be calculated in the test beds attached to metal objects. In summary, the results of the experimental study and related findings are expected to provide guidelines to the users of RFID technology for localization in building construction.

Aug 1, 2013

By William E. Roscoe

"Mineral exploration properties are those on which an economically viable mineral deposit has not yet been discovered. Such properties are bought, sold, optioned and joint ventured on the basis of their perceived potential for the existence and discovery of a viable mineral deposit. The intrinsic value of an exploration property is therefore based on the exploration potential. One measure of the exploration potential is the amount that can be justified to spend on exploration for a viable deposit.The appraised value method uses a cost approach to value exploration properties. It is based on the premise that an exploration property is worth the meaningful past exploration expenditures plus warranted future costs to test remaining exploration potential. Results of past exploration work are analyzed in order to retain only those past expenditures that are productive in terms of identifying remaining potential. Warranted future costs comprise a reasonable exploration budget to test that potential.INTRODUCTIONThe purpose of this paper is to describe a cost approach to the valuation of mineral exploration properties and to provide some valuation examples. The particular cost approach described is the Appraised Value Method, which is best applied to mineral properties at the exploration stage.At present there are no comprehensive regulations or guidelines in Canada which specify what approaches and methods to use for the valuation of mineral properties. In this paper, the Appraised Value Method described is one method that the writer considers to be accepted industry practice for mineral properties at the exploration stage.Mineral properties are valued for a number of reasons, including mergers and acquisitions, non arm's length transactions, pricing of initial public offering of stock, support for property agreements, litigation, expropriation, and insurance claims."

Jan 1, 2003

By Hasini Wijayaratne

Anode cover material, a mixture of crushed electrolyte and alumina, is a crucial part of an aluminium reduction cell because of its important role in maintaining overall heat balance. However, until recently little attention has been given to understanding or controlling its composition and quality. The thermal conductivity of anode cover material determines the extent of the heat loss from the top of the cell. This will change as a function of the granulometry and composition of the applied cover as well as over time as the cover material consolidates on top of the cell. The ability to measure or predict the thermal conductivity of fresh and ageing cover is an important tool for managing cell heat balance. Recent studies have shown that granulometry or more correctly, voidage is likely to be the predominant determinant of thermal conductivity of anode cover materials. We have developed equipment to measure the thermal conductivity of granular cover material and tested the relative importance of composition (ratio of alumina to crushed electrolyte) and granulometry/voidage on cover thermal conductivity. In general, our results confirm that granulometry is the dominating factor. Generally, high voidages contribute to lowering the thermal conductivity especially when particles are mostly fine. However the relationships between granulometry, voidage and thermal conductivity are complex due to the varying nature of heat transfer between particles. Aging of granular cover material occur during cell operation forming a consolidated crust due to exposure to heat and fumes over time. Structure and thermal behaviour of this consolidated crust is also important in understanding the overall properties of cover. This paper presents the outcomes of laboratory studies conducted in order to understand the thermochemical behaviour of anode cover material and in particular, the role of fines in anode covers mixtures.

Jan 1, 2011

By I. Spector

A SHORTAGE of cement in the Prairie Provinces, together with an aggressive policy on the part of the Saskatchewan Government in bringing new industries to the province, combined to create a favourable set of conditions for the establishment of Saskatchewan's first cement plant on the outskirts of Regina. Built by Saskatchewan Cement Corporation Limited, this single-kiln plant, tl1e latest addition to cement producers on the Prairies, began operations in the Fall of 1956. Location of the plant followed the trend of building cement manufacturing facilities in market areas rather than at raw material sources. In 1957, all assets of the Corporation were taken over by Inland Cement Company Limited and the plant and quarry now operate as Saskatchewan Cement Company, an Inland division. The Regina plant's production makes up approximately eleven per cent of the productive capacity of all plants in the Prairie Provinces. At present, two types of cement are manufactured -normal portland and sulphate resisting.

Jan 1, 1960

By G. A. Gillett, C. F. Bonney

"The Davy McKee combined mixer-settler (CMS), is a liquid-liquid contactor, which has been commercially applied to the recovery of uranium from dilute sulphuric acid-bearing leach liquors. CMS differs from most other solvent extraction systems in that the mixing and separation of the phases is carried out in the same vessel.IntroductionTypical solvent extraction plants for the recovery of uranium operate at organic to aqueous feed flow ratios of 1 : 2 to 1 : 30. Because it is beneficial to mix the organic and aqueous phases at an organic/aqueous (O / A) ratio of between I : 2 and 2 : I there is incompatibility between the over-all and operating O /A ratios.Conventional mixer-settler designs require an external recycle of the minority flow which results in the possibility of over-mixing, increased settling requirements and entrainment losses. Other workers have approached this problem in terms o f enhanced sett ling and this has been partly successful.Davy McKee's approach involved a radical rethink of the principles of liquid-liquid contact and separation.Description of CMSThe CMS has the important advance that the required mixing O/A ratio can be achieved without external recycle and is not affected by the O /A ratio of the feeds. Three zones co-exist within the CMS unit-a central mixing zone and upper and lower separation zones. A pump impeller on a draught tube is installed within the mixing zone and baffles are installed above and below the mixing zone. Conventional mixer- settlers have several undesirable features which ca n largely be eliminated using the CMS system:"

Jan 1, 1983

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to maximise health and safety performance in the mining industry through implementing continual improvement in management of major unwanted events. A comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This will be extended to outburst, coal burst and bumps, interface displays and controls, tailings dams and inrush in 2013. RISKGATE presents substantive and leading edge controls to assist industry stakeholders in the design, management and reporting of organisational and regulatory compliance requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry. All major Australian mining companies are contributing topic experts to this broad industry initiative. In the first 24 months, nine coal mining companies nominated over 80 different experts who contributed over 400 days of individual time to the knowledge capture workshops. RISKGATE is the largest single Australian Coal Association Research Program (ACARP) occupational health and safety (OHS) initiative to date.

Aug 1, 2013