Search Documents

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter in blowing the copper stage has been developed to predict the molten temperature. The key assumption of the model was that white metal and gas phases in the converter were in thermal and chemical equilibrium. In this model, the chemical reaction of white metal and oxygen was accomplished completely. So long as sulfur existed in the bath, the generation of Cu2O was frozen. The reaction rate was considered to be constant and controlled by the reacted sulfur. The converter temperature was calculated by heat balances over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depended on process parameters such as oxygen efficiency, molten emissivity and oxygen enrichment.

Jan 1, 2007

By D. Jean Hutchinson, Mark Diederichs

"Cable bolts are an important support component in modern underground mines. If an optimized cable bolt system is to be achieved, it is insufficient to focus on cable bolt layout design or on cable bolt installation in isolation. Cable bolt support, like all engineered systems, requires a holistic approach, encompassing integrated elements of design, implementation and verification. The “Cable bolting Cycle” described in this paper incorporates these components along with related tools and procedures which should be used together to ensure effective and efficient cable bolt support.Design involves the consideration of demand, capacity and constraints as outlined in this paper. The demands imposed on the sup-port system by the rock mass response to excavation under the combined action of stress and gravity must be matched to the capacity of the cable bolt array. The cable bolt system capacity is a function of the component strengths of the steel strand and the bond (load transfer) and by the deformation response and retention characteristics of the system. The design is bounded by operational and economic constraints.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.The information presented in this paper represents a very abbreviated version of much broader concepts, procedures and design charts, presented in a practical cable bolting handbook by Hutchinson and Diederichs (1996)."

Jan 1, 1996

By H. Tokuichi, H. Ohta, K. Sato

A physical separation technique of tantalum capacitors from waste print circuit boards is in a development phase in Japan. A tantalum capacitor consists of an exterior coating of resin (epoxy resin) mixed with silica fillers and a sintered tantalum compact, the latter of which is impregnated with manganese dioxide (MnO2). In this study, we developed a process to recover tantalum oxide from tantalum capacitors by roasting, fluidized-bed separation, and hydrometallurgical treatments. Our aim was to recover tantalum oxide with high purity from waste tantalum capacitors. In this process, the exterior resin was selectively decomposed by roasting without oxidation and pulverization of the sintered tantalum compact at a proper temperature. Furthermore, the decomposed resin with silica filler on the surface of the sintered tantalum compact was mostly removed by fluidized-bed separation. The surface of the sintered tantalum compact was cleaned by ultrasonic irradiation in an acid solution to remove the MnO2 paste as well as residual Ag paste and silica filler. The impregnated MnO2 in the sintered tantalum compact was leached as Mn(II) ions using acid solutions via the reducing effect of tantalum metal to recover purified tantalum oxide.

Jan 1, 2014

By E. F. Evoy

"The Gunnar uranium deposit was within metasedimentary rocks of the late Archaen Tazin Group. These rocks were intensely altered by albitization so that the immediate host to the ore consisted dominantly of albite, and by the subsequent introduction of calcite. The ore consisted of disseminated pitchblende and uranophane in a pipe-shaped breccia zone. Oxidation of the ore was more intense near surface than at depth, but there was no near-surface enrichment.IntroductionThe Gunnar Mine site is on the tip of Crackingstone Peninsula, on the north shore of Lake Athabasca, Province of Saskatchewan, Canada. The peninsula forms the southern part of the Beaverlodge mining area. The ore consisted of disseminated pitchblende and uranophane in brecciated metasedimentary rocks of the Tazin Group, and the deposit was characterized by extreme albitization and subsequent carbonatization of the host environment.Production from the mine began in 1954 and the ore was depleted by 1963. In that interval the deposit yielded about 5 million tonnes of ore containing about I. 75 kg/tonne U3O8. It was mined initially from an open-pit and subsequently from underground; the open-pit contributed about 55% of total tonnage. Uranium was recovered by atmospheric leaching in sulphuric acid, ion exchange concentration, and precipitation with magnesia.This paper is based on studies made during the productive life of the mine and is concerned primarily with pre-ore alteration of the rocks containing the deposit, and with the ore mineralogy."

Jan 1, 1986

By Andrew Barnes

The adsorption capacity of peat collected from a proposed mine development in northern Sweden has been determined using laboratory column experiments in which peat was irrigated with a simulated (acidic) waste rock dump leachate. The simulated leachate was made using a hydrogen peroxide leach of composite waste rock from the proposed mine development. The waste rock samples were composited in proportion to their predicted extractable tonnage for the mine development in order to generate a more representative leachate solution for the waste rock facility. As expected the test revealed that the peat material shows a very high affinity for attenuation with greater than 70% of Co, 90% of Ni and 95% of Cu removed from influent solutions through the majority of the tests demonstrating the potential benefits in mine water treatment. In contrast, it was found that Fe is initially released from the peat at concentrations up to 100 mg/L and can mean potential problems for the water released depending on the receiving environment. The exact mechanisms for Fe release is uncertain, though it is suspected that ion exchange / competitive desorption is responsible. Inspection of the laboratory results and drainage data from the natural peat wetland receiving drainage during overburden prestriping and mine development at the mine site are comparable, confirm the validity of the experiments, and further emphasize the potential for future use of pre-stripped peat material in managing water quality.

Aug 1, 2013

By Bill Charbonneau

Lumen, lm The measurement unit of light emitted by a light source 60W incandescent840 lumens 32W T8 linear fluorescent3200 lumens 54W T5HO linear fluorescent5000 lumens 400W metal halide24,000 lumens

Oct 1, 2010

By A. Kapoor, L. Morin, S. Mortazavi, P. Béedard, Gould. W. D., A. Kuiper

The degradation of thiocyanate in a simulated gold mill effluent was studied using a laboratory scale rotating biological contactor (RBC). Complete SCN- removal was obtained at temperatures of 8 and 12°C, and a hydraulic retention time of approximately 3.3 h. The NH4+ produced by thiocyanate hydrolysis was oxidized by nitrifying bacteria to NO2 and NO3-. The HS- produced by thiocyanate hydrolysis was chemically and biologically oxidized to elemental S, which was subsequently biologically oxidized to sulfate. Incomplete sulfur oxidation occurred in the RBC, particularly at 8°C and elemental sulfur deposition was observed on the RBC disks. The RBC feed exhibited toxicity to rainbow trout but the RBC was effective in removing the acute toxicity of thiocyanate.

Jan 1, 2005

By Karina Forster

Open stope design depends on the ore body geometry, loading conditions and rock mass properties to estimate stope dilution and ground support requirements. Rock mass conditions for design primarily rely upon estimates of well established rock classification systems. Many sources of data exist for obtaining estimates for these rock mass classification values which include core logging, geotechnical mapping, geological mapping as well as linking one classification system to another through the use of empirically derived equations. The extent of mapping coverage can also vary significantly based on the data collection technique. This paper proposes an approach where individual components of rock mass classification systems are collected by the different available data collection techniques. Data from different rock types are also considered separately based on their alteration characteristics and general observation products. Data from the Cameco Corporation Eagle Point Mine is presented and an approach is outlined for obtaining average representative classification values for stope hanging wall characterization. The effectiveness of this approach is demonstrated through the analysis of a data base of hanging wall dilution information.

Jun 1, 2012

?Introduction to the Delphi Group ?Why is carbon important to your organization ?Key elements of a carbon management strategy ?Inventory ?Risk & opportunity scan ?Mitigation options and financial mechanisms ?Identify targets and develop policy ?Communication and improvement ?Manage for success

May 1, 2009

By C. Stapel, P. D. Roberts, D. G. Jones, W. G. Macdonald, R. J. De Meijer

"Abstract-Measurement of natural radioactivity has been used in both a qualitative and a quantitative way in mineral exploration, particularly in the search for uranium. In the last five years, the Kernfysisch Versneller Instituut (KVI) and British Geological Survey (BGS) have designed, built and tested a new detector system that greatly improves quantitative applications in mineral exploration, especially on the seafloor and in the nearshore zone. The new system is an enhancement of an earlier BGS design. The major improvements comprise the use of a highly sensitive ?-ray detector, together with new data processing, from which concentrations of natural radionuclides may be deduced in real time. After laboratory analysis of samples, these concentrations can be converted into mineral percentages. Once the mineralogy of an area has been characterized, this conversion can also be done in real time.Thus far the system has mainly been used to map heavy-mineral concentrations in coastal subtidaland intertidal sediments. For such work the multi-sensor detector probe is towed on the seafloor and various parameters are recorded continuously. The probe contains, in addition to the gamma-ray detector, a water-pressure sensor (giving water depth) and an acoustic device to measure bottom roughness. The system, when used together with high-precision positioning systems such as D-GPS, enables the production of detailed maps of bathymetry, bottom roughness, and seafloor radioactivity or mineral distribution. These maps allow mineral concentrations to be readily correlated with seabed topography and sediment type. In the same way, ?-ray detectors could be used advantageously during dredging operations to provide on-line assessment of the mineral content of the dredged sediment as well as to guide the direction of dredging. Additionally, the same technique could be used to monitor the subsequent fate of a dredge spoil after dumping on the seafloor.Natural radioactivity arising from potassium and the thorium and uranium decay series has potential use for the fast and reliable assessment of siliciclastic and phosphatic impurities in limestones. Detection of such impurities may preclude the use of the limestone for chemical or cement production.Apart from its use in exploration, the technique has significant potential in mineral processing, particularly of heavy minerals. It can be applied as on-line quality control in dry and wet separation processes and for process control, by using decisions based on the results to control valves and other instrumentation. In addition, it can also be used in environmental monitoring of waste arising from mineral extraction and processing. In conclusion, the technique described has a diversity of applications in exploration, mining and mineral processing."

Jan 1, 1997

By Engineering Staff

In 1958, the Iron Ore Company of Canada decided to proceed with the Carol Project. The ore deposits in the area are part of the highly metamorphosed southern zone of the Labrador Trough. They lie along the shore of W a bush lake, in the western part of Newfoundland-Labrador, 190 miles north of Sept-Iles. The project is designed to mine, by open-pit methods, 17,200,000 long tons of crude ore, grading 37 per cent iron, per year. This ore will be beneficiated to produce 7,000,000 long tons of concentrate, grading 66 per cent iron, of which 5,500,000 long tons will be pelletized. Production is scheduled to commence this summer. Initially, ore will be taken from 45-foot benches in the Smallwood mine, using jet-piercing production drills and large-scale blasting with "slurry" explosives. Four 13-yard electric shovels will muck the broken ore into 100-ton trailer trucks. The trailers will be hauled to two 2,000-ton loading pockets, which feed the ore into 100-ton railcars. Four ore trains, each comprised

Jan 1, 1962

By Victor Azbe

Azbe System of Controlled Calcination To obtain good and cheap lime there are certain fundamental requirements that need to be satisfied. These are : (1) Proper combustion of fuel and steady supply of heat to the kiln. (2) Proper heat distribution in the kiln. (3) Uniform drawing of lime through the several shaft sections. (4) Complete cooling of the lime and recovery of the heat. (5) Temperature control of the hot zone by economical means. (6) Ample draft to obtain high capacity. (7) Arrangements to facilitate operation. Figure 17 shows diagrammatically one of the smaller kilns, intended for large stone. Such a kiln can be supplied with gas from a centrally located automatic gas producer, or, as shown, from an integral producer located snugly against the kiln. These producers make very good gas and have a gasification capacity of either 10 or 15 tons of coal a day. The producers have water-sealed ash pits, a rather thick fuel bed that is conducive to the making of high-CO gas, and are under forced draft. No steam is used. Clinkering is prevented by admixing some spent gas from the kiln with the air. Coal feeding is from a coal bunker through spouts into the hoppers over the producer. This is done, at proper intervals, by manual operation of slides, but it is planned to install mechanical feeders. Central mechanical gas producers have the advantage of requiring little labour, but the blowing of soot is a problem, as also is the proper distribution of the gas among several kilns. In the case of integral gas producers, soot from the centre burner is blown back into the producer to be burned, and the supply of gas to the kiln is controlled by regulation of air to the producer. In large plants, the mechanical producer may be preferable, but in small ones, the integral producer is cheaper, better, and more reliable. The kiln shown in Figure 17 is suitable for both systems of gas supply. It will be noticed that there are no side gas burners. All gas enters the kiln through the centre burner in a manner that permits any desired amount of gas to be directed to any of the kiln sections by the aid of regulating slides.

Jan 1, 1946

By D. M. Muir

Many plants produce iron(II)/(III) waste liquors which must be treated by neutralisation and precipitation to remove the iron. Iron can be precipitated as crystalline goethite or jarosite by controlled oxidation at low pH and as magnetite by controlled oxidation at high pH, but only at elevated temperatures (>70°C). This study focuses on the characterisation and settling properties of the iron oxides produced at ambient temperatures using various neutralising agents in order to improve the performance of thickeners. It was found that two-stage addition of caustic to FeC12 solutions produced a fast settling material characterised by Mossbauer spectroscopy and XRD as maghemite and magnetite. However, lime and magnesia additions resulted in more ferrihydrite formation and much lower settling rates because of the enhanced oxidation of Fe(II) by air. Settling rates decreased significantly as the proportion of Fe(III) to Fe(II) in the liquor increased. The mechanism of iron oxide precipitation is discussed together with some reasons for the different behaviour of the neutralising agents.

Jan 1, 2006

By Andre Panteleyev, Charels S. Ney, John M. Anderson

"Sam Goosly prospect, 22 miles southeast of Houston, B.C., was discovered in 1967 through geochemical reconnaissance. Soil sampling interpreted with respect to an east-to-west ice movement led to drilling targets.Mineralization is in a window of rocks thought to be Hazelton Group surrounded by Tertiary volcanic rocks and intruded by two stocks separated by about one mile. A westerly quartz monzonite stock is dated 61.1 m.y. and an easterly gabbro-monzonite complex is dated 52.5 m.y. The Tertiary volcanics are trachyandesites shown by the B.C. Department of Mines and Petroleum Resources to be in part extrusive equivalents of the gabbro, and they overlie Hazelton rocks uncomformably. Copper-molybdenum mineralization is sparsely developed in the westerly stock. Silver-copper mineralization forms an elongate west-dipping slab between the stocks in Hazelton rocks, which are continuously pyritized. The gabbro stock is not mineralized, but some dikes related to it are slightly so. Tertiary rocks are pyritized, but are not known to carry copper-silver mineralization. Hazelton rocks are divided into a lower conglomerate, an intermediate pyroclastic unit and an upper mainly sedimentary unit. They form a west-facing homocline. Coppersilver mineralization resides in the pyroclastic unit, mainly in a massive dust tuff through which are lenticular units of lapilli tuff. Well-mineralized rock is typically a breccia of light fragments in a dark chlorite-sulphide matrix. Sulphides are pyrite, chakopyrite and locally pyrrhotite, with very minor tetrahedrite, s phalerite and other sulphosalts. Rock alteration is predominantly a pervasive pyrite-sericite type, with widespread tourmaline, scorzalite, gypsum, ankerite and traces of fluorite. The most evident control of the copper-silver mineralization is the gross parallelism, over a strike length of 1.5 miles, to Hazelton strata, particularly a massive dust .tuff unit. In detail, mineralization crosscuts bedding and there is no appreciable banding within sulphides . A strictly syngenetic origin is untenable, but some initial concentration in a volcanogenic environment with subsequent modification by thermal processes seems likely."

Jan 1, 1972

By I-H. Jung, J. Kim

"Mg alloys are extensively used as light structural materials in modern industry. Mn and RE (rareearth) metals are effectively used as alloying elements to enhance the properties of Mg alloys. Therefore, the thermodynamic database of those alloys is important in the Mg alloy design and processing. Critical evaluation and optimization of all available literature data for the Mn-RE systems were conducted to obtain reliable thermodynamic functions. The Mn-RE systems shows systematic changes in the phase diagrams and thermodynamic properties with increasing atomic number in the lanthanide series. This systematic approach for all RE elements allows to resolve inconsistencies in the available experimental data. INTRODUCTIONRare Earth (RE) metals are widely used in many industrial fields including permanent magnet, electronic materials and structural materials. As a small addition of RE can enhance magnetic, electronic, optical and mechanical properties of numerous materials, the usage of the RE is still expanding regardless of the strategic control of their supply.Magnesium alloys are getting great scientific and industrial attention as the lightest structural materials. One of the drawbacks of Mg alloys is their poor formability at room temperature due to the limited slip system with hcp crystal structure. Recently, several studies (Farzadfar et al., 2011; Sandloebes et al., 2010; Stanford, 2010; Stanford et al., 2008; Yan et al., 2010) show that the additions of small amounts of RE can considerably enhance the ductility of Mg alloys. Therefore, a lot of research on Mg-RE alloys is undergoing to clarify the role of RE on the enhanced deformation mechanism and to find out the most optimum Mg alloy compositions. In order to respond to the need of Mg-RE alloy development, a large thermodynamic database for Mg alloys containing RE has been developed with critical systematic analysis and optimization of the entire RE series data. This includes the thermodynamic database of the Mg-RE (Kang et al., 2009), Mg-RE-RE (Kang et al., 2009), Mg-Al-RE (Jin et al., 2011; Jin et al., 2010), Mg-Zn-RE and Mg-Mn-RE systems."

Jan 1, 2012

By K. Thuro, B. Sellmeier, M. Krautblatter

"Recent rockfall events, like the Tramin rockfall at January 21st, 2014, underline the significance of a comprehensive hazard assessment. A common way of estimating the hazard along infrastructure is the performance of run-out modelling using 3D rockfall codes like Rockyfor3D or RAMMS::Rockfall (Dorren, 2010, Bartelt et al., 2013). The potential block volumes are often roughly estimated from talus material and an overview of the source area, where the magnitude assessment is usually physically and intellectually demanding. Nevertheless especially for increased magnitudes, the volume estimation is crucial in terms of hazard analysis. Mid-Magnitude-Events exceed the load capacity of the most mitigation measures and their date of failure is hard to predict. Here we define the term Mid-Magnitude-Events as block volumes between boulder falls (10-100 m³) and block falls (100-10,000 m³) (Whalley, 1984).The current contribution provides an approach of integral process analysis for a 200 m3 carbonate block above the federal road B 305 near the city of Salzburg in the Bavarian Alps, Germany. We performed detailed analysis of the critical carbonate block exposed to planar failure. The block volume and the dimensions of the failure surface were mapped in detail, due to the unique occasion of an accessible failure surface. The discontinuity persistence was recorded to assess a minimal degree of fragmentation for a potential failure scenario. A maximum degree of fragmentation was estimated due to recording of block dimensions at the talus slope resulting from frequent rockfalls.We performed parameter studies in terms of run-out modelling using the code RAMMS::Rockfall (Bartelt et al., 2013), taking the recorded data for block fragmentation into account. In our contribution, we aim to demonstrate a comprehensive approach for hazard assessment of mid magnitude rockfalls, taking detachment processes, fragmentation and run-out analysis into account."

Jan 1, 2015

By Q. B. Li, B. Gonçalves da Silva, J. T. Germaine, H. H. Einstein, Z. Moradian

"Shale gas and oil production has grown rapidly in recent years, and consequently there are increasing demands to understand the mechanical and microseismic properties of shale. Acoustic emission (AE) monitoring provides useful information on the fracture mechanisms of shale rocks, and provides a basis for interpreting field seismic observations. While there have been attempts for microseismic monitoring of conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted to understand the characteristics of the AE waveforms propagated through Opalinus shale rock in the time and frequency domains. Frequency range, arrival time, first arrival amplitude and other parameters such as counts, duration and energy of the waves generated from artificial and natural sources in the shale specimens were detected and compared with AE characteristics of granite, a brittle rock that has been extensively investigated. The experimental tests showed that there are some important factors that influence the analyses and interpretations of seismic surveys and microseismic monitoring of shale compared to granite. One of these factors is the anisotropic behavior of shale that causes the wave to propagate with different velocities in different directions. Also bedding planes and micro-discontinuities in the shale cause attenuation of the waves. Thus the AE waveforms that arrive at the sensor are a distorted and attenuated versions of the source waveform.INTRODUCTIONMonitoring microseismic activity from hydraulic fracturing of shale provides vital information for mapping injection paths and fluid migration in order to check the effectiveness of the hydraulic fracture stimulation. Analysis of microseismic source locations can be used to identify fracture networks induced or mobilized during the hydraulic fracturing operation (Rotherd and Shapiro, 2003). On the other hand, by monitoring and assessing detected signals from hydraulic fracturing one can evaluate the induced seismic impact of the stimulation operation.While there have been attempts to monitor microseismic events in conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted on Opalinus shale to understand its acoustic emission (AE) characteristics in the time and frequency domains."

Jan 1, 2015

By D. B. Dreisinger, M. Rasouli

"Developing technology to address the environmental hazards associated with selenium in mine-impacted waters has been a serious challenge. Ion exchange (IX) has been identified as a potential treatment technology. This paper begins with a review on selenium adsorption with commercially-available basic anionic exchangers (BAS). It then looks at the use of resins for selenium removal via modification with the addition of -O, -N, or -S-containing chelating ligands and chelating polymeric ion exchangers pre-loaded with immobilized metal cations. The synthesis of chelating exchangers requires a final product with a highly stable metal in the ligand-metal complex. The nature, oxidation state, size, and affinity of the metal for the target oxyanions and the size, degree of protonation and space configuration of the oxyanion are among critical factors affecting the oxyanion uptake. There is a limited number of studies on the critical parameters affecting the selenium affinity for chelating exchangers. Such a study could fill in the gaps of our understanding of selenium-metal-chelating ligand interactions and assist in developing a new ion exchanger. In addition to commercial IX resins, layered double hydroxide materials (LDH) have received attention for oxyanion removal from waste water. The adsorption capacity of the LDHs are affected by the crystallinity of LDH, the nature of metal components, the ratio of metals, charge and type of anion, and the space between the layers. In particular, the Friedel phase (FP), a member of the LDH family, showed high adsorption capacity for selenate removal from synthetic solution. A study is currently underway at the University of British Columbia to investigate the effect of different synthesis methods and aging on the suitability of FP for selenium removal from mine waste water."

Jan 1, 2017

By Andrew Young

A Question Murray Dodge ?Inco Stobie Maintenance ?I visually inspect my hoist ropes every day and seldom find anything. Is there a better way to do the inspection?? Based on HRIA research activities, the answer would seem to be ?yes?.

May 1, 2006

By R. W. Coburn

The results of field experiments on wells which required stimulation indicated that engineered well-completions will cause an increase in ultimate recovery at reduced costs. Techniques and tools have been developed which can be used to establish well conditions most conducive to successful stimulation. Cementing, perforating and treating are bound together so completely that the success of one phase is completely dependent on the .effectiveness of the preceding phase. A method of determining the efficiency or effectiveness of any given well-stimulation treatment has been derived. Pressure behaviour during a treatment can be analyzed to yield the total percentage of the formation which has been treated.

Jan 1, 1960